冷弯薄壁卷边槽钢轴压构件畸变与局部相关屈曲试验研究

对卷边尺寸不同的两类腹板中间设置加劲卷边槽形截面,共18个冷弯薄壁型钢固支轴压试件进行畸变屈曲与局部屈曲相关作用的静力试验研究。得到试件的屈曲模式、相关屈曲行为、破坏模式以及极限荷载。试验结果表明：畸变屈曲与局部屈曲的耦合相关对试件的变形和极限荷载有不利作用;畸变屈曲与局部屈曲的耦合相关作用存有较大的屈曲后承载力;畸变屈曲与局部屈曲的耦合相关顺序,即畸变屈曲 局部屈曲耦合相关、局部屈曲 畸变屈曲耦合相关,对试件的变形、非线性平衡路径、破坏模式以及极限荷载的影响有所不同。采用ABAQUS有限元软件对试件进行模拟分析,计算结果与试验结果吻合良好。     

冷弯薄壁型钢卷边槽形截面构件畸变屈曲控制研究

基于部分加劲板件的畸变屈曲和局部屈曲的稳定系数比较,提出了冷弯薄壁型钢卷边槽形截面构件畸变屈曲发生于局部屈曲之后或畸变屈曲不发生的临界控制条件;给出了通过构件畸变屈曲计算长度控制畸变屈曲的临界条件;提出一种控制畸变屈曲的构造措施,即在卷边间加设缀板,并通过已有试验对其有效性进行验证,同时推导了卷边间缀板的刚度需求。结果表明：通过构件截面尺寸控制畸变屈曲不发生或发生在局部屈曲之后,可以不考虑构件畸变屈曲的影响,简化冷弯薄壁型钢卷边槽形截面构件承载力的计算;计算长度小于畸变屈曲半波长一半的构件不发生畸变屈曲;通过在卷边间加设缀板的构造措施能有效阻止部分加劲板件的转动,构件的畸变屈曲荷载和承载力都有很大的提高,缀板布置间距不同,构件承载力的提高幅度也不同,缀板间距越小,构件承载力提高幅度越大。算例分析表明,满足一定间距和刚度需求的缀板能够提高构件的畸变屈曲承载力或避免畸变屈曲的发生。     

受弯的冷弯卷边槽钢畸变屈曲强度和其相关屈曲承载力

受弯的冷弯薄壁卷边槽钢基本上有板件局部屈曲,截面畸变屈曲和构件弯扭屈曲三种屈曲模式,随后有它们之间的相关屈曲。由于畸变屈曲模式对缺陷的敏感度高,因此其屈曲后强度提高的幅度远低于局部屈曲模式。但是与局部屈曲模式相比,畸变屈曲模式抵抗破坏的能力却很强。可以用有限单元法计算受弯卷边槽钢截面的畸变屈曲强度。本文介绍了澳大利亚-新西兰标准AS/NZS4600-2005,用手算法计算受弯卷边槽钢截面的弹性畸变屈曲应力,並用直接强度法计算其相关的屈曲承载力。     

Behaviour of cold-formed singly symmetric columns

An experimental investigation into the behaviour of cold-formed plain and lipped channel columns compressed between fixed and pinned ends is presented in this paper. It is shown experimentally that local buckling does not induce overall bending of fixed-ended singly symmetric columns, as it does of pin-ended singly symmetric columns. Consequently, local buckling has a fundamentally different effect on the behaviour of pin-ended and fixed-ended singly symmetric columns. In order to show this fundamental different effect caused by local buckling, a series of tests was performed on plain and lipped channels brake-pressed from high strength structural steel sheets. Four different cross-section geometries were tested over a range of lengths which involved pure local buckling, distortional buckling as well as overall flexural buckling and flexural-torsional buckling. The different effects of local buckling on the behaviour of fixed-ended and pin-ended channels are investigated by comparing strengths, load–shortening and load–deflection curves, as well as longitudinal profiles of buckling deformations. The purpose of the paper is to demonstrate experimentally the different effects of local buckling on the behaviour and strengths of fixed-ended and pin-ended channels.     

高强冷弯薄壁型钢卷边槽形截面轴压柱畸变屈曲试验研究

本文对550MPa高强冷弯薄壁型钢卷边槽形截面轴压构件畸变屈曲性能进行了试验研究,17根试件的试验结果表明:由于试件局部屈曲一般发生在畸变屈曲之前,促使畸变屈曲提前出现,这种相关作用减弱了构件整体刚度,降低了构件承载力;澳洲规范AS/NZS 4600:1996及北美规范NAS 2004中关于发生畸变屈曲构件承载力的计算方法没有考虑局部屈曲和畸变屈曲相关作用的不利影响。依据试验结果本文提出了一种修正直接强度法的建议计算方法,该法计算结果与试验结果较为接近且偏安全。     

Strength of cold-formed lipped channel beams under interaction of local,distortional and lateral torsional buckling

Cold-formed thin-walled lipped channel steel beams may undergo buckling modes such as short half-wavelength local buckling, intermediate half-wavelength distortional buckling and long half-wavelength lateral-torsional buckling or a combination of these before failure. ABAQUS software based on finite element analysis is used to analyse the interaction behaviour of these buckling modes in this study. The finite element model, after calibration with experimental results available in the literature, is used to perform parametric studies, to evaluate the behaviour and strength of such beams under different types of interactions due to variation of material and member properties. The large volume of synthetic data thus generated over a range of failure modes along with the available test results are used to evaluate different equations for calculating the strength of such cold-formed lipped channel beams. Based on the comparison, a method for the design of lipped channel beams failing under the interaction of local, distortional and overall lateral torsional buckling is recommended.     

Coupled instabilities with distortional buckling in cold-formed steel lipped channel columns

The paper addresses the elastic post-buckling behaviours of cold-formed steel lipped channel simply supported columns affected by mode interaction phenomena involving distortional buckling, namely local/distortional, distortional/global (flexural-torsional) and local/distortional/global mode interaction. The results presented were obtained by means of Abaqus shell finite element analyses adopting column discretisations into fine 4-node element meshes. In order to enable a thorough assessment of all possible mode interaction effects, the column lengths and cross-section dimensions were carefully selected to ensure similar local, distortional and/or global buckling loads. One analyses otherwise identical (elastic) columns having initial geometrical imperfections (i) with various configurations (combinations of the competing critical buckling mode shapes) and (ii) sharing the same overall amplitude.     

高强冷弯薄壁型钢轴压柱畸变屈曲研究

550MPa高强冷弯薄壁型钢卷边槽形截面轴压柱发生畸变屈曲时会出现三种模式（O—O,O-I,I—I）,考虑材料和几何双重非线性的有限元法对三种畸变屈曲模式的构件承载力、变形模式、畸变屈曲应力、横截面应力的分布等相关性能进行比较分析,可看出三种畸变屈曲模式诸性能存在较大不同,同时畸变屈曲与局部屈曲、整体屈曲在相关性能方面也存在不同。采用直接强度法对畸变屈曲轴压柱极限承载力进行计算,计算结果与试验结果较吻合,故在计算畸变屈曲轴压柱极限承载力时建议采用直接强度法．     

Design of cold-formed steel channels with stiffened webs subjected to bending

The objectives of this study are to investigate the structural behaviour and evaluate the appropriateness of the current direct strength method on the design of cold-formed steel stiffened cross-sections subjected to bending. The stiffeners were employed to the web of plain channel and lipped channel sections to improve the flexural strength of cold-formed steel sections that are prone to local buckling and distortional buckling. An experimental investigation of simply supported beams with different stiffened channel sections has been conducted. The moment capacities and observed failure modes at ultimate loads were reported. A nonlinear finite element model was developed and verified against the test results in terms of strengths, failure modes and moment–curvature curves. The calibrated model was then adopted for an extensive parametric study to investigate the moment capacities and buckling modes of cold-formed steel beams with various geometries of stiffened sections. The strengths and failure modes of specimens obtained from experimental and numerical results were compared with design strengths predicted using the direct strength method specified in the North American Specification for cold-formed steel structures. The comparison shows that the design strengths predicted by the current direct strength method (DSM) are conservative for both local buckling and distortional buckling in this study. Hence, the DSM is modified to cover the new stiffened channel sections investigated in this study. A reliability analysis was also performed to assess the current and modified DSM.     

中间加劲复杂卷边槽钢纯弯构件弹性畸变屈曲应力计算方法研究

为了研究中间加劲复杂卷边槽钢纯弯构件弹性畸变屈曲应力简化计算方法,采用有限条分析软件CUFSM对不同参数的复杂卷边槽钢、∑形复杂卷边槽钢以及腹板V形加劲复杂卷边槽钢各70个构件的畸变屈曲应力进行数值分析.在此基础上,借鉴现有板件局部屈曲应力的表达方式,引入畸变屈曲系数,经拟合分析提出上述构件畸变屈曲应力的简化计算公式,并将复杂卷边槽钢和腹板V形加劲复杂卷边槽钢的公式进行合并,对公式的有效性进行验证.     

Post-buckling behaviour and DSM design of web-stiffened lipped channel columns with distortional and local mode interaction

This paper examines the design and load-carrying capacity of fixed-ended web-stiffened lipped channel columns eroded by mode interaction behaviour combined with distortional and local deformations. Initially, the paper presents the results of an experimental investigation of compressive tests on web-stiffened lipped channel columns fabricated from cold-formed mild steel with a thickness of 1.50 mm, which is aimed at determining their failure load-carrying capacity; the experimental investigation also aims to provide experimental evidence of the occurrence of such coupling phenomena concerning distortional and local modes, namely, local-distortional interaction and distortional-local interactive failures. Then, the paper examines the ultimate strength data of experimental columns, both reported in this paper and collected from the literature, and concludes that the current direct strength method (DSM) provides very unsafe predictions concerning such a detrimental interaction nature. Next, two DSM-based design approaches, namely, the nominal strength against local-distortional (NLD) and distortional-local (NDL) procedures, are presented and evaluated on the basis of all available experimental ultimate strength data. Finally, proposals and design considerations based on the DSM-shape for the thin-walled cold-formed steel sections, which fail in mixed modes of distortional and local buckling, are presented.     

受压翼缘外带卷边和中间加劲肋的冷弯型钢梁的局部和扭转屈曲特性

采用数值模型分析受压翼缘含卷边和中间加劲肋的冷弯型钢梁的屈曲特性。通过一系列非线性有限元分析,研究了由局部或扭转屈曲导致失稳的两侧翼缘处均含卷边和中间加劲肋的冷弯Z型钢的弯曲性能。研究了中间加劲肋的尺寸和位置以及卷边加劲肋和中间加劲肋的相互作用对型材的屈曲特性和极限强度的影响。有限元分析结果常可用来检验用欧洲设计规范在预测这类断面极限强度时的精确度。     

Compression tests of longitudinally stiffened plates undergoing distortional buckling

This paper describes a series of compression tests performed on longitudinally stiffened plates fabricated from a mild steel plate of thickness of 4.0 mm with nominal yield stress of 235.0 MPa. The stiffened plates with longitudinal stiffeners of a range of rigidities were tested to failure. The ultimate strengths and performances of the longitudinally stiffened plates in compression undergoing distortional buckling or interaction between local and distortional buckling were investigated experimentally and theoretically. The compression tests indicated that the critical buckling mode was dependent mainly on the rigidity of the longitudinal stiffeners and the width-to-thickness ratio of the sub-panels. A noticeable interaction between local and distortional buckling was also observed for some stiffened plates. A significant post-buckling strength reserve was shown for those sections with distortional buckling and for those sections showing interaction between local and distortional buckling. A limiting strength curve for distortional buckling of longitudinally stiffened plates was studied. Simple design strength formulas in the direct strength method are proposed to account for the distortional buckling and the interaction between local and distortional buckling of longitudinally stiffened plates. The strength curves were compared with the test and FE results conducted. The adequacy of the strength curve was confirmed. A set of conclusions on the buckling behavior of longitudinally stiffened plates was drawn from the experimental studies.     

不同斜卷边檩条的局部屈曲和畸变屈曲

利用Hancock的简化模型分析了卷边槽形、卷边Z形檩条的畸变屈曲,用有限元方法计算了卷边槽形、卷边Z形檩条的畸变屈曲荷载以及翼缘局部屈曲系数,研究了卷边角度对畸变屈曲荷载的影响,提出斜卷边加劲板的屈曲系数取值以及屈曲系数关于卷边角度变化的公式。经对比验证,在卷边角度40°～90°的范围内,误差在2%以内。可供实际设计参考。     

冷弯薄壁卷边槽钢轴心受压构件承载力计算的折减强度法

为了研究冷弯薄壁卷边槽钢轴心受压构件的极限承载力,对15根轴心受压的冷弯薄壁卷边槽钢进行了破坏性试验,并采用有限元分析方法对试件进行模拟分析,有限元计算结果与试验结果吻合良好,验证了有限元方法的有效性,然后对典型截面构件进行大量的有限元参数分析。研究结果表明：冷弯薄壁卷边槽钢轴心受压构件的极限承载力随着构件翼缘宽厚比、腹板高厚比、长细比以及钢材强度的增大而减小。通过参数分析得到了考虑局部屈曲、整体屈曲和畸变屈曲影响的构件屈服强度折减系数,提出了冷弯薄壁卷边槽钢轴心受压构件承载力计算的折减强度法及其相应计算公式,且通过试验验证了本文折减强度法计算卷边槽钢轴心受压构件极限承载力的适用性。     

卷边槽钢纯弯构件畸变屈曲板组约束系数的直接强度法计算

现行国家规范《冷弯薄壁型钢结构技术规范》（GB50018—2002）提出了适用于各种型钢构件板组的约束系数统一计算公式。针对冷弯薄壁卷边槽钢纯弯构件畸变屈曲运用直接强度法计算受压翼缘板组约束系数,并与规范计算结果比较,得到一些有价值的结论,供设计研究参考。     

高强冷弯薄壁型钢卷边槽形截面轴压构件试验研究及承载力分析

对63根屈服强度550MPa高强冷弯薄壁型钢卷边槽形截面轴压构件进行试验研究,分析了构件的屈曲模式和极限承载力,并将参考AISI规范、澳洲规范和北美规范及我国现行行业标准《低层冷弯薄壁型钢房屋建筑技术规程》（报批稿）计算的构件承载力与试验结果进行分析比较。在此基础上,对高强超薄壁型钢卷边槽形截面轴压构件的承载力合理计算模式进行研究。结果表明：高强超薄壁型钢卷边槽形截面轴压构件在宽厚比较大时会出现畸变屈曲模式;采用等效板件方法计算加劲板件有效宽度后,我国《低层冷弯薄壁型钢房屋建筑技术规程》（报批稿）适用于屈曲强度550MPa、厚度小于2.00mm的冷弯薄壁型钢卷边槽形截面构件承载力计算。     

Tests and finite element analysis of pin-ended channel columns with inclined simple edge stiffeners

This paper presents an experimental investigation and a finite element analysis on cold-formed channels with inclined simple edge stiffeners compressed between pinned ends. Compression tests of pin-ended channel columns with inclined simple edge stiffeners have not been performed till now. A total of 36 channel specimens including three different cross sections with different edge stiffener inclined angles and column lengths were tested. Detailed measurements of initial geometric imperfections and material properties of the specimens were also conducted before the above tests. Failure modes include local buckling, distortional buckling, flexural buckling and interaction among these buckling modes were observed in tests. The results indicate that inclined angle and loading position significantly affect the ultimate load-carrying capacity and failure mode of specimens. Moreover, a non-linear finite element model was developed and verified against tests. Geometric and material non-linearities were included in the model. Results from the finite element analysis agree well with experimentally ultimate loads and failure modes. However, it should be improved on prediction for certain displacement.     

550MPa高强冷弯薄壁卷边槽钢受弯构件畸变屈曲试验研究

为了研究屈服强度550MPa高强冷弯薄壁型钢受弯构件的畸变屈曲性能,分别对直卷边、斜卷边和复杂卷边3种卷边形式的12组高强冷弯薄壁槽钢受弯试件进行了静力试验研究,其中纯弯试验6组,非纯弯试验6组。试验结果表明,卷边形式是影响试件发生畸变屈曲或局部和畸变相关屈曲的重要因素。相同卷边形式下,非纯弯试件的承载力均高于纯弯试件的承载力,且提高幅度与试件屈曲破坏模式有关,只发生畸变屈曲的试件承载力提高幅度最大,而在发生局部和畸变相关屈曲的试件中,由畸变屈曲引起破坏的试件承载力提高幅度次之,由局部屈曲引起破坏的试件承载力提高幅度最小。     

冷弯薄壁卷边槽钢轴压柱屈曲实用计算研究

基于直接强度法,拟合冷弯薄壁卷边槽钢轴压柱局部屈曲、畸变屈曲实用计算公式,取局部屈曲、畸变屈曲与整体屈曲三者的最小值作为轴压柱屈曲计算结果。3种屈曲计算值与有关试验值的对比分析表明,所提出的实用计算公式在适用范围内与试验值吻合较好,且计算公式简单、实用,避免了对专用计算程序的依赖。