Near 100% CO selectivity in CH4 direct catalytic oxidation at low temperatures (<700‡C) under unsteady state conditions

Almost 100% CO selectivity was achieved with small pulses of CH₄/O₂ (2/1), using very short residence times over a reduced NiO/La₂O₃ catalyst. One concludes that CH₄ conversion depends on its dissociation, whereas CO selectivity is mainly dependent on the strength of oxygen binding to the catalyst. Over the reduced catalyst, the oxygen species oxidize with difficulty (because of their strong binding to metal Ni) CO to CO₂, whereas over the unreduced catalyst (which contains Ni oxide), the oxygen species easily oxidize (because they are weakly adsorbed) CO to CO₂.     

Role of the surface state of Ni/Al2O3 in partial oxidation of CH4

The effect of gas phase O₂ and reversibly adsorbed oxygen on the decomposition of CH₄ and the surface state of a Ni/Al₂O₃ catalyst during partial oxidation of CH₄ were studied using the transient response technique at atmospheric pressure and 700°C. The results show that, when the catalyst surface is completely oxidized under experimental conditions, only a small amount of CO and H₂ can be produced from non‐selective oxidation of CH₄ by reversibly adsorbed oxygen which is more active in oxidizing CH₄ completely than NiO via the Rideal–Eley mechanism and both the conversions of CH₄ and O₂ and the selectivities to CO and H₂ are very low. Therefore, keeping the catalyst surface in the reduced state is the precondition of high conversion of CH₄ and high selectivities to CO and H₂. The surface state of the catalyst decides the reaction mechanism and plays a very important role in the conversions and selectivities of partial oxidation of CH₄. During partial oxidation of CH₄, no oxygen species but a small amount of carbon exists on the catalyst surface, which is favorable for maintaining the catalyst in the reduced state and the selectivity of CO. The results also indicate that direct oxidation is the main route for partial oxidation of CH₄, and the indirect oxidation mechanism is not able to gain dominance in the reaction under the experimental conditions. This revised version was published online in July 2006 with corrections to the Cover Date.     

Comparative Study on Partial Oxidation of Methane over Ni/ZrO2, Ni/CeO2 and Ni/Ce–ZrO2 Catalysts

The partial oxidation of methane has been studied by sequential pulse experiments with CH₄ O₂ CH₄ and simultaneous pulse reaction of CH₄/O₂ (2/1) over Ni/CeO₂, Ni/ZrO₂ and Ni/Ce–ZrO₂ catalysts. Over Ni/CeO₂, CH₄ dissociates on Ni and the resultant carbon species quickly migrate to the interface of Ni–CeO₂, and then react with lattice oxygen of CeO₂ to form CO. A synergistic effect between Ni and CeO₂ support contributes to CH₄ conversion. Over Ni/ZrO₂, CH₄ and O₂ are activated on the surface of metallic Ni, and then adsorbed carbon reacts with adsorbed oxygen to produce CO, which is composed of the main path for the partial oxidation of methane. The addition of ceria to zirconia enhances CH₄ dissociation and improves the carbon storage capacity. Moreover, it increases the storage capacity and mobility of oxygen in the catalyst, thus promoting carbon elimination.     

Dehydrogenation of propane with selective hydrogen combustion: A mechanistic study by transient analysis of products

The role of lattice and adsorbed oxygen species in propane dehydrogenation in a perovskite hollow fiber membrane reactor containing a Pt–Sn dehydrogenation catalyst was elucidated by transient analysis of products with a sub-millisecond time resolution. Propane is mainly dehydrogenated non-oxidatively to propene and hydrogen over the catalyst, while lattice oxygen of the perovskite oxidizes preferentially hydrogen to water. For achieving high propene selectivity at high propane conversions, the formation of gas phase O₂ on the shell side of the membrane reactor should be avoided. Otherwise, oxygen species adsorbed over the Pt–Sn catalyst participate in non-selective C₃H₈/C₃H₆ transformations to C₂H₄ and CO_x.     

Low-temperature reforming of ethanol over CeO2-supported Ni-Rh bimetallic catalysts for hydrogen production

A new series of Ni-Rh bimetallic catalysts with different Ni and Rh loadings on a high-surface-area CeO₂ was developed for the reforming of bio-ethanol at low-temperature (below 450 °C) to produce H₂-rich gas for on-site or on-board fuel cell applications. Oxidative steam reforming of ethanol (OSRE) over a Ni-Rh/CeO₂ catalyst containing 5 wt% Ni and 1 wt% Rh was found to be more efficient offering about 100% ethanol conversion at 375 °C with high H₂ and CO₂ selectivity and low CO selectivity compared to the steam reforming of ethanol (SRE) reaction which required a higher temperature of about 450 °C to achieve 100% ethanol conversion. The high temperature SRE reaction favors the formation of large amount of CO, which would make the downsteam CO cleanup more complicated for polymer electrolyte membrane fuel cell (PEMFC). The presence of O₂ in the feed gas was found to greatly enhance the conversion of ethanol to produce H₂ and CO₂ as major products. Increase in Ni content above 5 wt% in the catalyst formulation decreased the H₂ selectivity while the selectivity of undesirable CH₄ and acetaldehyde increased. The 1 wt% Rh/CeO₂ catalyst was twice as active as 10 wt% Ni/CO₂ catalyst in terms of ethanol conversion and acetaldehyde selectivity and this indicated that Rh was more effective in C–C bond cleavage than Ni. The reaction was found to proceed through the formation of acetaldehyde intermediate, which subsequently underwent decomposition to produce a mixture of CO and CH₄ or reforming with H₂O and O₂ to produce CO, CO₂ and H₂. The role of Rh is mainly to cleave the C–C and C–H bonds of ethanol to produce H₂ and COx while Ni addition helps converting CO into CO₂ and H₂ by WGS reaction under the conditions employed.     

Pulse studies of CH4 interaction with NiO/Al2O3 catalysts

Pulse studies of the interaction of CH₄ and NiO/Al₂O₃ catalysts at 500°C indicate that CH₄ adsorption on reduced nickel sites is a key step for CH₄ oxidative conversion. On an oxygen-rich surface, CH₄ conversion is low and the selectivity of CO₂ is higher than that of CO. With the consumption of surface oxygen, CO selectivity increases while the CO₂ selectivity falls. The conversion of CH₄ is small at 500°C when a pulse of CH₄/O₂ (CH₄O₂=21) is introduced to the partially reduced catalyst, indicating that CH₄ and O₂ adsorption are competitive steps and the adsorption of O₂ is more favorable than CH₄ adsorption     

CH4/CD4 isotope effect on the reaction of adsorbed hydrocarbon species in CO2-reforming over Ni/Al2O3 catalyst

By replacing CH₄ with CD₄, the isotope effect on the reaction of adsorbed hydrocarbon species with CO₂ over Ni/Al₂O₃ catalyst was studied using pulse surface reaction rate analysis (PSRA). The first-order rate constant for this step was 1.45 times larger for CH₄ than for CD₄. The observed isotope effect suggests that the reaction of adsorbed hydrocarbon species with CO₂ (or adsorbed oxygen) is rate-controlling for the reforming of CH₄.     

Oxy-CO2 reforming of methane to syngas over CoOx/MgO/SA-5205 catalyst

The oxy-CO₂ methane reforming reaction (OCRM) has been investigated over CoO_x supported on a MgO precoated highly macroporous silica–alumina catalyst carrier (SA-5205) at different reaction temperatures (700–900 °C), O₂/CH₄ ratios (0.3–0.45) and space velocites (20,000–100,000 cc/g/h). The reaction temperature had a profound influence on the OCRM performance over the CoO/MgO/SA-5205 catalyst; the methane conversion, CO₂ conversion and H₂ selectivity increased while the H₂/CO ratio decreased markedly with increasing reaction temperature. While the O₂/CH₄ ratio did not strongly affect the CH₄ and CO₂ conversion and H₂ selectivity, it had an intense influence on the H₂/CO ratio. The CH₄ and CO₂ conversion and the H₂ selectivity decreased while the H₂/CO increased with increasing space velocity. The O₂/CH₄ ratio and the reaction temperature could be used to manipulate the heat of the reaction for the OCRM process. Depending on the O₂/CH₄ ratio and temperature the OCRM process could be operated in a mildly exothermic, thermal neutral or mildly endothermic mode. The OCRM reaction became almost thermoneutral at an OCRM reaction temperature of 850 °C, O₂/CH₄ ratio of 0.45 and space velocity of 46,000 cc/g/h. The CH₄ conversion and H₂ selectivity over the CoO/MgO/SA-5205 catalyst corresponding to thermoneutral conditions were excellent: 95% and 97%, respectively with a H₂/CO ratio of 1.8.     

Performance of Ba0.5Sr0.5Co0.8Fe0.2O3 + δ membrane after laser ablation for methane conversion

A cross-shaped pattern was formed on the surface of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 − δ oxygen permeation membrane by laser ablation. A membrane reactor made from this membrane was operated for partial oxidation of methane to syngas in the presence of Ni/ZrO₂ catalyst. The CH₄ conversion and CO selectivity of the membrane reactor were 98.8% and 91.5%, respectively, and the oxygen permeation flux through the membrane was 11.0 ml/cm² min at 850 °C. The effects of space velocity (SV) on CH₄ conversion and CO selectivity in such reactor were discussed. The mechanism of POM in such membrane reactor may follow the combustion and reforming mechanism.     

Oxidative Reforming of Bio-Ethanol Over CuNiZnAl Mixed Oxide Catalysts for Hydrogen Production

Hydrogen (H₂) is expected to become an important fuel for the future to be used as an energy carrier in automobiles and electric power plants. A promising route for H₂ production involves catalytic reforming of a suitable primary fuel such as methanol or ethanol. Since ethanol is a renewable raw material and can be cheaply produced by the fermentation of biomass, the ethanol reforming for H₂ production is beneficial to the environment. In the present study, the steam reforming of ethanol in the presence of added O₂, which in the present study is referred to as oxidative steam reforming of ethanol (OSRE), was performed for the first time over a series of CuNiZnAl mixed oxide catalysts derived from layered double hydroxide (LDH) precursors. The effects of Cu/Ni ratio, temperature, O₂/ethanol ratio, contact time, CO co-feed and substitution of Cu/Ni by Co were investigated systematically in order to understand the influence of these parameters on the catalytic performance. An ethanol conversion close to 100% was noticed at 300 °C over all the catalysts. The Cu-rich catalysts favor the dehydrogenation of ethanol to acetaldehyde. The addition of Ni was found to favor the C–C bond rupture, producing CO, CO₂ and CH₄. Depending upon the reaction condition, a H₂ yield between 2.5 and 3.5 moles per mole of ethanol converted was obtained. A CoNi-based catalyst exhibited better catalytic performance with lower selectivity of undesirable byproducts, namely CH₃CHO, CH₄ and CO.     

Oxidative dehydrogenation of 4-vinylcyclohexene into styrene over ZrO2 catalyst promoted with Fe2O3 and CaO

The oxidative dehydrogenation of 4-vinylcyclohexene (VCH) into styrene was carried out in the presence of oxygen over a ZrO₂ catalyst promoted with Fe₂O₃ and CaO. Intrinsically, ZrO₂ showed high dehydrogenation activity, which resulted in 80% styrene selectivity with 45% conversion at 425 °C and LHSV 3 h⁻¹. When the ZrO₂ was further promoted with calcium and iron, CaO/Fe₂O₃/ZrO₂, the highest styrene selectivity of 88.9% was obtained as well as the lowest deactivation. The deactivation of catalyst was prohibited properly through the introduction of oxygen in the reactant together with the modification of Fe₂O₃/ZrO₂ with CaO. The CaO/Fe₂O₃/ZrO₂ showed constant catalytic activity and selectivity for more than 50 h without deactivation. The selectivity of styrene was strongly influenced by the mole ratio of O₂/VCH and 95% selectivity with 80% conversion was obtained at O₂/VCH mole ratio of 6 over Fe₂O₃/ZrO₂. It is thought that the oxidative dehydrogenation proceeds through the dehydrogenation (DH) of ring-hydrocarbon of VCH followed by selective combustion of hydrogen (SHC) and the high selectivity of styrene was achieved by the bi-functional role of ZrO₂ for DH and SHC reactions. This revised version was published online in July 2006 with corrections to the Cover Date.     

Steam reforming of ethanol on Ni–CeO2–ZrO2 catalysts: Effect of doping with copper, cobalt and calcium

Steam reforming (SR) and oxidative steam reforming (OSR) of ethanol were investigated over undoped and Cu, Co and Ca doped Ni/CeO₂–ZrO₂ catalyst in the temperature range of 400–650 °C. The nickel loading was kept fixed at 30 wt.% and the loading of Cu and Co was varied from 2 to 10 wt% whereas the Ca loading was varied from 5 to 15 wt.%. The catalysts were characterized by various techniques, such as surface area, temperature programmed reduction, X-Ray diffraction and H₂ chemisorption. For Cu and Co doped catalyst, CuO and Co₃O₄ phases were detected at high loading whereas for Ca doped catalyst, no separate phase of CaO was found. The reducibility and the metal support interactions were different for doped catalysts and varied with the amount and nature of dopants. The hydrogen uptake, nickel dispersion and nickel surface area was reduced with the metal loading and for the Co loaded catalysts the dispersion of Ni and nickel surface area was very low. For Cu and Ca doped catalysts, the activity was increased significantly and the main products were H₂, CO, CH₄ and CO₂. However, the Co doped catalysts showed poor activity and a relatively large amount of C₂H₄, C₂H₆, CH₃CHO and CH₃COCH₃ were obtained. For SR, the maximum enhancement in catalytic activity was obtained with in the order of NCu5. For Cu–Ni catalysts, CH₃CHO decomposition and reforming reaction was faster than ethanol dehydrogenation reaction. Addition of Cu and Ca enhanced the water gas shift (WGS) and acetaldehyde reforming reactions, as a result the selectivity to CO₂ and H₂ were increased and the selectivity to CH₃CHO was reduced significantly. The maximum hydrogen selectivity was obtained for Catalyst N (93.4%) at 650 °C whereas nearly the same selectivity to hydrogen (89%) was obtained for NCa10 catalyst at 550 °C. In OSR, the catalytic activity was in the order N > NCu5 > NCa15 > NCo5. In the presence of oxygen, oxidation of ethanol was appreciable together with ethanol dehydrogenation. For SR reaction, the highest hydrogen yield was obtained on the undoped catalyst at 600 °C. However, with calcium doping the hydrogen yields are higher than the undoped catalyst in the temperature range of 400–550 °C.     

La0.6Sr0.4Co0.8Ga0.2O3‐δ (LSCG) hollow fiber membrane reactor: Partial oxidation of methane at medium temperature

In this study, La_0.6Sr_0.4Co_0.8Ga_0.2O_3‐δ (LSCG) hollow fiber membrane reactor was integrated with Ni/LaAlO₃‐Al₂O₃ catalyst for the catalytic partial oxidation of methane (POM) reaction. The process was successfully carried out in the medium temperature range (600–800°C) for reaction of blank POM with bare membrane, catalytic POM reaction and swept with H₂:CO gas mixture. For the catalytic POM reaction, enhancement in selectivity to H₂ and CO is obtained between 650–750°C when O₂:CH₄ <1. High CH₄ conversion of 97% is achieved at 750°C with corresponding H₂ and CO selectivity of about 74 and 91%. The oxygen flux of the membranes also increased with the increase in oxygen partial pressure gradient across the membrane. The postreacted membranes were tested via XRD and FESEM‐EDX for their crystallinity and surface morphology. XPS analysis was further used to investigate the O1s, Co 2p and Sr 3d binding energies of the segregated elements from the reducing reaction environment. © 2013 American Institute of Chemical Engineers AIChE J, 59: 3874–3885, 2013     

Partial oxidation of methane over Ni/Ce-Zro<Subscript>2</Subscript>/θ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The catalytic behavior of Ni/Ce-ZrO₂/θ-Al₂O₃ has been investigated in the partial oxidation of methane (POM) toward synthesis gas. The catalyst showed high activity and selectivity due to the heat treatment of the support and the promotional effect of Ce-ZrO₂. It is suggested that the support was stabilized through the heat treatment of γ-Al₂O₃ and the precoating of Ce-ZrO₂, on which a protective layer was formed. Moreover, sintering of the catalyst was greatly suppressed for 24 h test. Pulse experiments of CH₄, O₂ and/or CH₄/O₂ with a molar ratio of 2 were systematically performed over fresh, partially reduced and well reduced catalyst. Results indicate that CH₄ can be partially oxidized to CO and H₂ by the reactive oxygen in complex NiO_x species existing over the fresh catalyst. It is demonstrated that POM over Ni/Ce-ZrO₂/θ-Al₂O₃ follows the pyrolysis mechanism, and both the carbonaceous materials from CH₄ decomposition over metallic nickel and the reactive oxygen species present on NiO_x and Ce-ZrO₂ are intermediates for POM.     

Raney Ni catalysts derived from different alloy precursors Part II. CO and CO2 methanation activity

Catalytic activity, in conjunction with reaction mechanism, was studied in the methanation of CO and CO₂ on three Raney Ni catalysts derived from different Ni-Al alloys using different leaching conditions. Main products were CH₄ and CO₂ in CO methanation, and CH₄ and CO in CO₂ methanation. Any other hydrocarbon products were not observed. Over all catalysts, CO methanation showed lower selectivity to methane and higher activation energy than CO₂ methanation. The catalyst derived from alloy having higher Ni content using more severe leaching conditions, namely higher reaction temperature and longer extraction time, showed higher specific activity and higher selectivity to methane both in CO and CO₂ methanation. In CO and CO₂ methanation on Raney Ni catalyst, catalytic activity was seen to have close relation with the activity to dissociate CO This paper was presented at the 2004 Korea/Japan/Taiwan Chemical Engineering Conference held at Busan, Korea between November 3 and 4,2004.     

Modeling of Catalytic CO2 Methanation Using Smart Computational Schemes

An analyzing tool as a sustainable method to combine CO₂ capture and production of CH₄ by utilizing CO₂ as a feedstock is proposed. The impact of incorporating metallic promoters such as Fe, La, Ce, and Co to an Al₂O₃-supported catalyst containing Ni as the first metal in the CO₂ methanation was modeled. Smart models were employed to analyze the CO₂ conversion and CH₄ selectivity in CH₄ production from CO₂. The genetic programming (GP) model provides a mathematical framework for the estimation of CO₂ conversion and CH₄ selectivity. The model inputs are catalyst surface area, temperature, H₂/CO₂ ratio, gas-hourly space velocity, and catalyst pore volume and diameter. The results confirm that the GP model estimates the CO₂ conversion and CH₄ selectivity very well.     

Oxidation of butenes to maleic anhydride on MnMoO4 based catalyst

The oxidation of n-butene-1 was carried out in a stirred tank reactor and in a pulse reactor using MnMoO₄ as a catalyst. This catalyst exhibits a fairly good selectivity to maleic anhydride. MnMoO₄ shows a polyfunctional nature; it is possible to distinguish the properties of isomerization, dehydrogenation, oxidation with oxygen insertion, and complete oxidation by varying parameters such as temperature, oxygen concentration and contact time.The compositions of the products in the oxidation of n-butene-1 carried out in a pulse reactor are completely different in the presence and in the absence of oxygen, respectively. In the absence of oxygen, MnMoO₄ is a very selective catalyst in the dehydrogenation of n-butene-1 to butadiene. In the presence of oxygen, CO and CO₂ are the main products together with small amounts of maleic anhydride.The selectivity of MnMoO₄ to butadiene formation has been attributed to the presence of MoO bonds which are responsible for dehydrogenation reactions.A monocenter oxidation mechanism, accounting for the formation of CO, CO₂, and maleic anhydride, has been proposed in which the gaseous oxygen is considered to be adsorbed on the same center of the hydrocarbon.     

Oxidative coupling of methane over LaF3/La2O3 catalysts

We studied the oxidative coupling of methane over the LaF₃/La₂O₃ (5050) catalyst. The catalyst was found active even at 873 K. At 1023 K, the C₂ yield was 12.7% at 26.0% CH₄ conversion and 49.1% C₂ selectivity. It was found to be stable and had a lifetime not less than 50 h at 1023 K. The catalyst was effective in C₂H₆ conversion to C₂H₄. XRD results indicated that the catalyst was mainly rhombohedral LaOF. It is suggested that the catalyst has ample stoichiometric defects and generates active oxygen sites suitable for methane dehydrogenation.     

Cerium-promoted Ni/SiO2 catalyst for CO methanation

Ce-promoted Ni catalysts were developed and applied in a CO methanation reaction. The 10%Ni/SiO₂ catalyst exhibits poor initial CO conversion (32.8%) and rapid deactivation with the highest methane selectivity during CO the methanation reaction. In contrast, the 4%Ce–10%Ni/SiO₂ catalyst shows dramatically increased initial CO conversion, which is up to 90.7%. Additionally, the apparent activation energy, Ea value, of 4%Ce–10%Ni/SiO₂ was calculated to be 102.2 kJ/mol according to the Arrhenius equation, which is much lower than that of the 10%Ni/SiO₂ catalyst, which was 139.1 kJ/mol. Based on various characterization results, it is found that the added Ce significantly improves the dispersion of the supported nickel, suppresses the sintering of nickel particles, and forms more adsorbed CO species of three-fold carbonyl species, resulting in higher CO conversion and good stability during the CO methanation reaction.     

Reactivity of a NiO/Al2O3 oxygen carrier prepared by impregnation for chemical-looping combustion

The reactivity of a Ni-based oxygen carrier prepared by hot incipient wetness impregnation (HIWI) on α-Al₂O₃ with a NiO content of 18 wt% was studied in this work. Pulse experiments with the reduction period divided into 4-s pulses were performed in a fluidized bed reactor at 1223 K using CH₄ as fuel. The number of pulses was between 2 and 12. Information about the gaseous product distribution and secondary reactions during the reduction was obtained. In addition to the direct reaction of the combustible gas with the oxygen carrier, CH₄ steam reforming also had a significant role in the process, forming H₂ and CO. This reaction was catalyzed by metallic Ni in the oxygen carrier and H₂ and CO acted as intermediate products of the combustion. No evidence of carbon deposition was found in any case. Redox cycles were also carried out in a thermogravimetric analyzer (TGA) with H₂ as fuel. Both tests showed that there was a relation between the solid conversion reached during the reduction and the relative amount of NiO and NiAl₂O₄ in the oxygen carrier. When solid conversion increased, the NiO content also increased, and consequently NiAl₂O₄ decreased. Approximately 20% of the reduced nickel was oxidized to NiAl₂O₄, regardless ΔX_s. NiAl₂O₄ was also an active compound for the combustion reaction, but with lower reactivity than NiO. Further, the consequences of these results with respect to the design of a CLC system were investigated. When formation of NiAl₂O₄ occurred, the average reactivity in the fuel reactor decreased. Therefore, the presence of both NiO and NiAl₂O₄ phases must be considered for the design of a CLC facility.