Synthesis and electrochemical properties of submicron LiNi0.8Co0.2O2 by a polymer-pyrolysis method

A polymer-pyrolysis method was used to synthesize LiNi_0.8Co_0.2O₂, which has potential application in lithium ion batteries. The effect of calcination temperature and time on the structure and electrochemical performance of the material was investigated. XRD analysis showed that the powders obtained by calcination at 750 °C for 3 h had the best-ordered hexagonal layer structure. SEM image showed these powders were fine, narrowly distributed with platelet morphology. The charge-discharge tests demonstrated these powders had the best electrochemical properties, with an initial discharge capacity of 189 mAh/g and capacity retention of 95.2% after 50 cycles when cycled at 50 mA/g between 3.0 and 4.3 V. Besides, these powders also had exhibited excellent rate capability.     

A delithiated LiNi0.65Co0.25Mn0.10O2 electrode material: A structural, magnetic and electrochemical study

A crystalline LiNi_0.65Co_0.25Mn_0.10O₂ electrode material was synthesized by the combustion method at 900 °C for 1 h. Rietveld refinement shows less than 3% of Li/Ni disorder in the structure. Lithium extraction involves only the Ni²⁺/Ni⁴⁺ redox couple while Co³⁺ and Mn⁴⁺ remain electrochemically inactive. No structural transition was detected during cycling in the whole composition range 0 < x < 1.0. Furthermore, the hexagonal cell volume changes by only 3% when all lithium was removed indicating a good mechanical stability of the studied compound. LiNi_0.65Co_0.25Mn_0.10O₂ has a discharge capacity of 150 mAh/g in the voltage range 2.5-4.5 V, but the best electrochemical performance was obtained with an upper cut-off potential of 4.3 V. Magnetic measurements reveal competing antiferromagnetic and ferromagnetic interactions - varying in strength as a function of lithium content - yielding a low temperature magnetically frustrated state. The evolution of the magnetic properties with lithium content confirms the preferential oxidation of Ni ions compared to Co³⁺ and Mn⁴⁺ during the delithiation process.     

Novel synthesis of layered LiNi1/2Mn1/2O2 as cathode material for lithium rechargeable cells

A new solution combustion synthesis of layered LiNi_0.5Mn_0.5O₂ involving the reactions of LiNO₃, Mn(NO₃)₂, NiNO₃, and glycine as starting materials is reported. TG/DTA studies were performed on the gel-precursor and suggest the formation of the layered LiNi_0.5Mn_0.5O₂ at low temperatures. The synthesized material was annealed at various temperatures, viz., 250, 400, 600, and 850 °C, characterized by means of X-ray diffraction (XRD) and reveals the formation of single phase crystalline LiNi_0.5Mn_0.5O₂ at 850 °C. The morphology of the synthesized material has been investigated by means of scanning electron microscopy (SEM) and suggests the formation of sub-micron particles. X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV) studies on the synthesized LiNi_0.5Mn_0.5O₂ powders indicate that the oxidation states of nickel and manganese are +2 and +4, respectively. Electrochemical galvanostatic charge-discharge cycling behavior of Li//LiNi_0.5Mn_0.5O₂ cell using 1 M LiPF₆ in EC/DMC as electrolyte exhibited stable capacities of ∼125 mAh/g in the voltage ranges 2.8-4.3 V and 3.0-4.6 V and is comparable to literature reports using high temperature synthesis route. The capacity remains stable even after 20 cycles. The layered LiNi_0.5Mn_0.5O₂ powders synthesized by this novel route have several advantages as compared to its conventional synthesis techniques.     

Effect of ZnO modification on the performance of LiNi0.5Co0.25Mn0.25O2 cathode material

ZnO was coated on LiNi_0.5Co_0.25Mn_0.25O₂ cathode (positive electrode) material for lithium ion battery via sol–gel method to improve the performance of LiNi_0.5Co_0.25Mn_0.25O₂. The X-ray diffraction (XRD) results indicated that the lattice structure of LiNi_0.5Co_0.25Mn_0.25O₂ was not changed distinctly after surface coating and part of Zn²⁺ might dope into the lattice of the material. Energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) proved that ZnO existed on the surface of LiNi_0.5Co_0.25Mn_0.25O₂. Charge and discharge tests showed that the cycle performance and rate capability were improved by ZnO coating, however, the initial capacity decreased dramatically with increasing the amount of ZnO. Differential scanning calorimetry (DSC) results showed that thermal stability of the materials was improved. The XPS spectra after charge–discharge cycles showed that ZnO coated on LiNi_0.5Co_0.25Mn_0.25O₂ promoted the decomposition of the electrolyte at the early stage of charge–discharge cycle to form more stable SEI layer, and it also can scavenge the free acidic HF species from the electrolyte. The electrochemical impedance spectroscopy (EIS) results showed ZnO coating could suppress the augment of charge transfer resistance upon cycling.     

Hydrothermal synthesis of LiNi0.9Co0.1O2 cathode materials

Ultrafine powders of LiNi_0.9Co_0.1O₂ were prepared under mild hydrothermal conditions. The product was characterized by XRD, TEM and EDS tests, which indicated that the obtained products were pure and well-crystallized LiNi_0.9Co_0.1O₂. The ICP-AES results indicated the products were lithium-deficient compounds. The addition of KOH hardly effected the crystallinity of the product but gave larger crystals.     

Spray-drying synthesized LiNi0.6Co0.2Mn0.2O2 and its electrochemical performance as cathode materials for lithium ion batteries

Layered LiNi_0.6Co_0.2Mn_0.2O₂ materials were synthesized at different sintering temperatures using spray-drying precursor with molar ratio of Li/Me = 1.04 (Me = transition metals). The influences of sintering temperature on crystal structure, morphology and electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ materials have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and charge-discharge test. As a result, material synthesized at 850 °C has excellent electrochemical performance, delivering an initial discharge capacity of 173.1 mAh g^− 1 between 2.8 and 4.3 V at a current density of 16 mA g^− 1 and exhibiting good cycling performance.     

Improvement of electrochemical and thermal properties of Li[Ni0.8Co0.1Mn0.1]O2 positive electrode materials by multiple metal (Al, Mg) substitution

Al and/or Mg-substituted Li[Ni_0.8Co_0.1Mn_0.1−x−yAl_xMg_y]O₂ were prepared by a co-precipitation method and characterized by X-ray diffraction with Rietveld refinement, thermogravimetric analysis, differential scanning calorimetry (DSC), and electrochemical measurements. The Rietveld refinement results show that cation mixing of Al and/or Mg-substituted Li[Ni_0.8Co_0.1Mn_0.1−x−yAl_xMg_y]O₂ was reduced with increased doping amounts of Al and Mg. The Al and/or Mg substitution in Li[Ni_0.8Co_0.1Mn_0.1]O₂ also resulted in improved electrochemical cycling behavior, structural stability, and thermal stability compared to pristine Li[Ni_0.8Co_0.1Mn_0.1]O₂. The improvements of electrochemical and thermal properties resulted from the stabilized host structure by Al and/or Mg incorporation into Li[Ni_0.8Co_0.1Mn_0.1]O₂.     

Structural, electrochemical and thermal properties of LiNi0.8−yTiyCo0.2O2 as cathode materials for lithium ion battery

Multiple substitution compounds with the formula LiNi_0.8−yTi_yCo_0.2O₂ (0≤y≤0.1) were synthesized by sol-gel method using citric acid as a chelating agent. The effects of titanium substitution on the structural, electrochemical and thermal properties of the cathode materials are investigated. A solid solution phase (R-3m) is observed in the range of 0≤y≤0.1 for the titanium-doped materials. X-ray photoelectron spectroscopy (XPS) shows that there are Ni³⁺, Ni²⁺, Co³⁺, Co²⁺ and Ti⁴⁺ five transition metal ions in titanium-doped materials. Rietveld refinement of X-ray diffraction (XRD) patterns indicates that titanium substitution changes the materials’ structure with different cationic distribution. An increase of the Ni/Co amount in the 3a Li site is found with the addition of titanium amount. An improved cycling performance is observed for titanium-doped cathode materials, which is interpreted to a significant suppression of phase transitions and lattice changes during cycling. The thermal stability of titanium-doped materials is also improved, which can be attributed to its lower oxidation ability and enhanced structural stability at delithiated state.     

LixNi0.7Co0.3O2 electrode material: Structural, physical and electrochemical investigations

The layered LiNi_0.7Co_0.3O₂ cathode material was synthesized by the combustion method using sucrose as fuel at 800 °C for 1 h, which leads to homogeneous size distribution with sub-micron particle size. The characterization of this material was realized using X-ray diffraction, scanning electron microscopy and completed by magnetic measurements. The Rietveld refinement shows the presence of 2.6% extra nickel in the interslab space. The presence of nickel ions in the lithium layers was confirmed by magnetization measurements. The 90° Ni-O-Ni ferromagnetic coupling is the main magnetic interactions. Lithium extraction from this phase occurs without major structural modifications. Cycling tests have shown a very good cycling stability at various current rates. Furthermore, this material delivers high reversible capacity of about 150 mAh/g in the 2.8-4.4 V range at the C/20.     

Effects of surface modification on the cycling stability of LiNi0.8Co0.2O2 electrodes by CeO2 coating

A high-performance LiNi_0.8Co_0.2O₂ cathode was successfully fabricated by a sol-gel coating of CeO₂ to the surface of the LiNi_0.8Co_0.2O₂ powder and subsequent heat treatment at 700 °C for 5 h. The surface-modified and pristine LiNi_0.8Co_0.2O₂ powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), slow rate cyclic voltammogram (CV), and differential scanning calorimetry (DSC). Unlike pristine LiNi_0.8Co_0.2O₂, the CeO₂-coated LiNi_0.8Co_0.2O₂ cathode exhibits no decrease in its original specific capacity of 182 mAh/g (versus lithium metal) and excellent capacity retention (95% of its initial capacity) between 4.5 and 2.8 V after 55 cycles. The results indicate that the surface treatment should be an effective way to improve the comprehensive properties of the cathode materials for lithium ion batteries.     

Modeling the impedance versus voltage characteristics of LiNi0.8Co0.15Al0.05O2

The power-delivery capability of lithium-ion cells based on LiNi_0.8Co_0.15Al_0.05O₂-based positive electrodes shows a significant dependence on the cell's state-of-charge. One reason for this behavior is the variation of the positive electrode's impedance with the oxide's lithium content. In this article, an electrochemical model based on concentrated solution porous electrode theory is used to model impedance data obtained on LiNi_0.8Co_0.15Al_0.05O₂-based positive electrodes charged to potentials ranging from 3.55 to 4.55 V versus Li. The parameters obtained from model fits include the exchange-current density and Li-ion diffusion coefficients in the oxide. The variations in these parameters with oxide potential are correlated with structural changes in the material observed during Li-ion intercalation-deintercalation reactions.     

Electrochemical characterization of zirconium-doped LiNi0.8Co0.2O2 cathode materials and investigations on deterioration mechanism

The electrochemical performance and the degradation mode of the zirconium doped cathode material, LiNi_0.8Co_0.18Zr_0.02O₂ were investigated and compared with the pristine cathode, LiNi_0.8Co_0.2O₂. The cyclic performance of the doped cathode was superior to the pristine cathode, especially under the high voltage cutoff, although its rate capability remained unimproved. The trend in the graphs of the differential capacity showed that the impedance growth of the cell made of the pristine cathode was much faster than the doped. From the results of the XRD pattern changes between before and after the galvanostatic cycling, less cation mixing and more ordered hexagonal structure were observed for the doped cathode. The impedance spectra showed that the charge transfer resistance for the pristine cathode grew significantly with cycling, while that for the doped cathode increased just moderately. Considerable decrease in the impedance was observed when the new lithium was substituted with the cycled anode, which implied that the interfacial impedance growth on the anode accounted for about 20% of the total impedance measured. It is concluded that the fading mode for LiNi_0.8Co_0.2O₂ is mainly due to the cation mixing, partially contributed by the impedance growth on the anode and by doping the pristine cathode with Zr, cation mixing can be efficiently suppressed.     

Preparation, morphology and electrochemical characteristics of LiNi1/3Mn1/3Co1/3O2 with LiF addition

LiNi_1/3Mn_1/3Co_1/3O₂ with LiF additives was prepared by a spray dry process, and characterized by XRD, SEM, TEM, ICP, XPS, EIS and charge-discharge testing. Although some of the LiF was lost during the preparation, the remaining LiF existed on the surface of the LiNi_1/3Mn_1/3Co_1/3O₂ particles and had little influence on its structure. The LiF addition could not only promote the combine of the particles and increase the tap density of the material, but also effectively improve the cyclic performance of LiNi_1/3Mn_1/3Co_1/3O₂ at high cutoff voltages (up to 4.7 V) and at a high current density. The EIS results suggest that the LiF presence could significantly suppress the increase in the charge transfer resistance that occurred during the charged storage state or after long cycling, which should be related to the improvement on the electrochemical properties.     

A study on electrochemical characteristics of LiCoO2/LiNi1/3Mn1/3Co1/3O2 mixed cathode for Li secondary battery

In this study, the LiCoO₂/LiNi_1/3Mn_1/3Co_1/3O₂ mixed cathode electrodes were prepared and their electrochemical performances were measured in a high cut-off voltage. As the contents of LiNi_1/3Mn_1/3Co_1/3O₂ in the mixed cathode increases, the reversible specific capacity and cycleability of the electrode enhanced, but the rate capability deteriorated. On the contrary, the rate capability of the cathode enhanced but the reversible specific capacity and cycleability deteriorated, according to increasing the contents of LiCoO₂ in the mixed cathode. The cell of LiCoO₂/LiNi_1/3Mn_1/3Co_1/3O₂ (50:50, wt.%) mixed cathode delivers a discharge capacity of ca. 168 mAh/g at a 0.2 C rate. The capacity of the cell decreased with the current rate and a useful capacity of ca. 152 mAh/g was obtained at a 2.0 C rate. However, the cell shows very stable cycleability: the discharge capacity of the cell after 20th charge/discharge cycling maintains ca. 163 mAh/g.     

Optimization of microwave synthesis of Li[Ni0.4Co0.2Mn0.4]O2 as a positive electrode material for lithium batteries

A positive electrode material for lithium ion battery applications was successfully synthesized using microwave irradiation. This microwave synthesis has several merits such as homogeneity of final product and much shorter reaction time compared to conventional synthetic methods. We synthesized spherical [Ni_0.4Co_0.2Mn_0.4](OH)₂ as a precursor by a co-precipitation method. The pelletized mixture of the precursor and lithium hydroxide was calcined under different reaction times and temperatures by applying 1200 W of microwave irradiation at 2.45 GHz. We determined the optimum conditions of microwave synthesis for positive electrode materials. The powders were characterized by X-ray diffraction, scanning electron microscopy, and electrochemical testing. The capacity, its retention, and thermal stability of Li[Ni_0.4Co_0.2Mn_0.4]O₂ synthesized by the microwave synthesis were comparable to the Li[Ni_0.4Co_0.2Mn_0.4]O₂ prepared by the high temperature calcination method.     

Synthesis and electrochemical characteristics of Al2O3-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium ion batteries

LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials have been coated with Al₂O₃ nano-particles using sol-gel processing to improve its electrochemical properties. The X-ray diffraction (XRD) pattern of the as-prepared Al₂O₃ nano-particles was indexed to the cubic structure of the γ-Al₂O₃ phase and had an average size of ∼4 nm. The XRD showed that the structure of LiNi_1/3Co_1/3Mn_1/3O₂ was not affected by the Al₂O₃ coating. However, the Al₂O₃ coatings on LiNi_1/3Co_1/3Mn_1/3O₂ improved the cyclic life performance and rate capability without decreasing its initial discharge capacity. These electrochemical properties were also compared with those of LiAlO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material. The electrochemical impedance spectroscopy (EIS) was studied to understand the enhanced electrochemical properties of the Al₂O₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ compared to uncoated LiNi_1/3Co_1/3Mn_1/3O₂.     

Synthesis of LiNi1/3Co1/3Mn1/3O2 cathode materials by using a supercritical water method in a batch reactor

LiNi_1/3Co_1/3Mn_1/3O₂ and LiCoO₂ cathode materials were synthesized by using a supercritical water (SCW) method with a metal salt solution in a batch reactor. Stoichiometric LiNi_1/3Co_1/3Mn_1/3O₂ was successfully synthesized in a 10-min reaction without calcination, while overlithiated LiCoO₂ (Li_1.15CoO₂) was synthesized using the batch SCW method. The physical properties and electrochemical performances of LiNi_1/3Co_1/3Mn_1/3O₂ were compared to those of Li_1.15CoO₂ by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and charge/discharge cycling tests. The XRD pattern of LiNi_1/3Co_1/3Mn_1/3O₂ was found to be similar to that of Li_1.15CoO₂, showing clear splitting of the (0 0 6)/(1 0 2) and (1 0 8)/(1 1 0) peak pairs as particular characteristics of the layered structure. In addition, both cathode powders showed good crystallinity and phase purity, even though a short reaction time without calcination was applied to the SCW method. The initial specific discharge capacities of the Li_1.15CoO₂ and LiNi_1/3Co_1/3Mn_1/3O₂ powders at a current density of 0.24 mA/cm² in 2.5-4.5 V were 149 and 180 mAh/g, and their irreversible capacity loss was 20 and 17 mAh/g, respectively. The discharge capacities of the Li_1.15CoO₂ and LiNi_1/3Co_1/3Mn_1/3O₂ powders decreased with cycling and remained at 108 and 154 mAh/g after 30 cycles, which are 79% and 89% of the initial capacities. Compared to the overlithiated LiCoO₂ cathode powders, the LiNi_1/3Co_1/3Mn_1/3O₂ cathode powders synthesized by SCW method had better electrochemical performances.     

Synthesis of LiNi0.9Co0.1O2 from Li2CO3, NiO or NiCO3, and CoCO3 or Co3O4 and their electrochemical properties

Cathode active materials with a composition of LiNi_0.9Co_0.1O₂ were synthesized by a solid-state reaction method at 850 °C using Li₂CO₃, NiO or NiCO₃, and CoCO₃ or Co₃O₄, as the sources of Li, Ni, and Co, respectively. Electrochemical properties, structure, and microstructure of the synthesized LiNi_0.9Co_0.1O₂ samples were analyzed. The curves of voltage vs. x in Li_xNi_0.9Co_0.1O₂ for the first charge–discharge and the intercalated and deintercalated Li quantity Δx were studied. The destruction of unstable 3b sites and phase transitions were discussed from the first and second charge–discharge curves of voltage vs. x in Li_xNi_0.9Co_0.1O₂. The LiNi_0.9Co_0.1O₂ sample synthesized from Li₂CO₃, NiO, and Co₃O₄ had the largest first discharge capacity (151 mA h/g), with a discharge capacity deterioration rate of −0.8 mA h/g/cycle (that is, a discharge capacity increasing 0.8 mA h/g per cycle).     

A novel method for the preparation of submicron-sized LiNi0.8Co0.2O2 cathode material

A novel method has been employed to synthesize layered LiNi_0.8Co_0.2O₂ cathode material by calcination of Ni–Co hydroxide–carbonate precursor prepared by a route involving separate nucleation and aging steps (SNAS) together with LiOH under air atmosphere. Thermogravimetry (TG) and differential thermal analysis (DTA) combined with on-line evolved gas mass spectrometry (EGMS) analysis were employed to study the reaction process. The synthesized material was characterized by means of X-ray diffraction (XRD), laser particle size distribution analysis, field emission scanning electron microscope (FE-SEM) and galvanostatic charge/discharge cycling. The synthesized LiNi_0.8Co_0.2O₂ presents a narrow distribution of submicron-sized particles and exhibits a good electrochemical property with initial discharge specific capacity of 194.8 mAh g⁻¹ in the voltage range 2.75–4.5 V (versus Li/Li⁺). The novel method for the preparation of submicron-sized LiNi_0.8Co_0.2O₂ material has the particular advantage of simple synthesis process and low synthesis cost.     

Synthesis and electrochemical performance of LiNi0.5Mn1.5O4 spinel compound

Spinel compound LiNi_0.5Mn_1.5O₄ was synthesized by a chemical wet method. Mn(NO₃)₂, Ni(NO₃)₂·6H₂O, NH₄HCO₃ and LiOH·H₂O were used as the starting materials. At first, Mn(NO₃)₂ and Ni(NO₃)₂·6H₂O reacted with NH₄HCO₃ to produce a precursor, then the precursor reacted with LiOH·H₂O to synthesize product LiNi_0.5Mn_1.5O₄. The product showed a single spinel phase under appropriate calcination conditions, and exhibited a high voltage plateau at about 4.6-4.8 V in the charge/discharge process. The LiNi_0.5Mn_1.5O₄ had a discharge specific capacity of 118 mAh/g at about 4.6 V and 126 mAh/g in total in the first cycle at a discharge current density of 2 mA/cm². After 50 cycles, the total discharge capacity was above 118 mAh/g.