Performance improvement of Nafion based solid state electrochemical supercapacitor

An electrochemical supercapacitor in all solid configuration using perfluorosulfonate ionomer as polymer electrolyte has been successfully realized. Electrodes of supercapacitor have been prepared using activated carbon material and Nafion ionomer. This latter had the double function of binder and electrolyte. Nafion 115 membrane has been used as electrolyte separator in the preparation of small scale supercapacitors. The capacitance performance of these devices is comparable or better than traditional systems, which use sulfuric acid as electrolyte. The electrochemical evaluation of studied supercapacitor has been carried out by cyclic voltammetry, dc charge/discharge measurements and electrochemical impedance spectroscopy. A capacitance of 90 F/g (referred to the weight of active carbon material in the electrode) has been obtained with carbon having surface area (SA) of about 1000 m²/g and, a capacitance of 130 F/g with activated carbon having SA of 1500 m²/g. These interesting results have been tentatively explained with an optimal configuration of electrodes and with the concomitant beneficial effects on the carbon pores of adsorbed water and Nafion distribution, which produce low distribute resistance in the carbon composite electrodes.     

Effects of electrolytic composition on the electric double-layer capacitance at smooth-surface carbon electrodes in organic media

As a fundamental research on the optimization of electrolyte composition in practical electrochemical capacitor device, double-layer capacitance at Glassy Carbon (GC) and Boron-doped Diamond (BDD), as typical smooth-surface carbon electrodes, has been studied as a function of the electrolyte composition in organic media. Specific capacitance (differential capacitance: F cm⁻²) determined by an AC impedance method, in which no contribution of mass-transport effects is included, corresponded well to integrated capacitance evaluated by conventional cyclic voltammetry. The specific capacitance at the GC electrode varied with polarized potential and showed clear PZC (potential of zero charge), while the potential dependence of the capacitance at BDD was very small. The effects of the solvent and the electrolytic salt on the capacitance behavior were common for both electrodes. That is, the sizes of the solvent molecule and the electrolytic ion (cation) strongly affected the capacitance at these smooth-surface carbon electrodes.     

Development of new nanocomposite based on nanosized-manganese oxide and carbon nanotubes for high performance electrochemical capacitors

We report the synthesis of a new composite electrode based on nanosized-manganese oxide and carbon nanotubes (CNTs) by electrophoretic deposition of CNTs on a stainless steel (SS) substrate followed by direct spontaneous reduction of MnO₄⁻ ions to MnO₂ to form the multi-scaled SS-CNT-MnO₂ electrode. The resulting material was characterized by scanning electron microscopy, energy dispersive X-ray analysis, cyclic voltammetry and galvanostatic charge-discharge in a 0.65 M K₂SO₄ aqueous solution. The binderless SS-CNT-MnO₂ nanocomposite electrode shows a very high specific capacitance of 869 F/g of CNT-MnO₂ and good stability during long galvanostatic charge-discharge cycling. To the best of our knowledge, this is one of the highest capacitance for manganese oxide electrode ever reported. In addition to its applicability in electrochemical capacitors, this methodology could be extended to develop other high performance nanocomposite material electrodes based on carbon nanotubes and metal oxide for the future generation of electrochemical power sources.     

Electrochemical determination of bromide at a multiwall carbon nanotubes-chitosan modified electrode

A multiwall carbon nanotubes (MWNTs)-chitosan modified glassy carbon electrode (GCE) exhibits attractive ability for highly sensitive cathodic stripping voltammetric measurements of bromide (Br⁻). In pH 1.8 H₂SO₄ solution, a substantial increase in the stripping peak current of Br⁻ (compared to bare GCE and chitosan modified GCE) is observed using MWNTs-chitosan modified electrode. Operational parameters were optimized and the electrochemical behaviors of Br⁻ were studied by different electrochemical methods. The kinetics parameters were measured, the number of electron transfer (n) was 1 and the transfer coefficient (α) is 0.17. A wide linear calibration range (3.6 × 10⁻⁷-1.4 × 10⁻⁵ g mL⁻¹) was achieved, with a detection limit of 9.6 × 10⁻⁸ g mL⁻¹. The mechanism of electrode reaction was fully discussed.     

Microwave-polyol synthesis of nanocrystalline ruthenium oxide nanoparticles on carbon nanotubes for electrochemical capacitors

The ruthenium oxide nanoparticles dispersed on multi-wall carbon nanotubes (CNTs) were successfully synthesized via microwave-polyol process combined with forced hydrolysis without additional thermal oxidation or electrochemical oxidation treatment. The HRTEM, Raman spectra and TGA curve indicate that CNTs were uniformly coated with crystalline and partially hydrous RuO₂·0.64H₂O nanoparticles of 2 nm diameter and the loading amount of ruthenium oxide in the composite could be controlled up to 70 wt.%. The specific capacitance was 450 Fg⁻¹ of ruthenium oxide/CNT composite electrode with 70 wt.% ruthenium oxide at the potential scan rate of 10 mV s⁻¹ and it decreased to 362 Fg⁻¹ by 18% at 500 mV s⁻¹. The specific capacitance of ruthenium oxide in the composite was 620 Fg⁻¹ of ruthenium oxide at 10 mV s⁻¹. The ruthenium oxide nanoparticles in ruthenium oxide/CNT nanocomposite electrode had a high ratio of outer charge to total charge of 0.81, which confirmed its high-rate capability of the composite through the preparation of the nano-sized ruthenium oxide particles on the external surface of CNTs.     

Wet chemical synthesis of Gd+3 doped vanadium Oxide/MXene based mesoporous hierarchical architectures as advanced supercapacitor material

In this paper, Gd³⁺ doped V₂O₅/Ti₃C₂T_x MXene (GVO/MX) hierarchical architectures have been synthesized by wet chemical approach. As prepared GVO/MX composite, along undoped VO and unsupported GVO were well characterized by XRD, FESEM, EDX, FT-IR and BET techniques. Electrochemical performance of VO, GVO and GVO/MX was evaluated by CV, GCD and EIS measurements. Among the three electrodes, GVO/MX composite exhibited highest electrochemical activity with the optimum specific capacitance of 1024 Fg^-1 at 10 mVs^?1. The specific capacitance of GVO/MX was ～1.7 and ～3 times higher than unsupported GVO (585 Fg^-1) and VO (326 Fg^-1), respectively. The cyclic life of GVO/MX with capacitance retention 96.12% was observed at 60 mVs^?1. EIS measurements showed reduction in electrochemical impedance for GVO/MX as compared to GVO and VO. The corresponding impedance values of Rct and Resr for GVO/MX were calculated as 18 Ω and 1.8 Ω, respectively. The superior capacitive ability of GVO/MX can be ascribed to its unique morphology, short diffusion path and high surface area of fabricated composite. Considering it, the present work provides a feasible strategy to fabricate highly effective electrode materials for next generation energy storage devices.     

Electrochemical behavior of high-pressure synthetic boron doped diamond powder electrodes

Boron doped diamond (BDD) was synthesized under high pressure and high temperature using B-doped graphite intercalation compositions (GICs) as carbon sources. The electrochemical characteristics of high-pressure synthetic BDD powder electrodes were investigated by measuring the cyclic voltammetry curves and AC impedance spectrum. For the [Fe(CN)₆]^3−/4− redox couple, the electrode reaction process is reversible or quasi-reversible at the scan rates of 0.01-1.0 V/s. At the low scan rate the linear relation between peak current and square root of scan rate indicates that the electrode process was a diffusion-controlled mass transport process. The electrochemical behavior is similar to a planar electrode. With the increasing of the scan rate the electrode process is controlled by the mass transport plus kinetic process. AC impedance spectra exhibit the porous structure characteristic of BDD powder electrode.     

Catalytic reduction of hydrogen peroxide at metal hexacyanoferrate composite electrodes and applications in enzymatic analysis

The electrocatalytic activity of various metal hexacyanoferrates (Mhcfs) (i) immobilized on graphite electrodes, and (ii) as components of a composite electrode was investigated with respect to the reduction of hydrogen peroxide. The flow-through working electrode was a thin layer consisting of a composite of Mhcf, graphite, and polymethylmetacrylate (PMMA) as a binder, sandwiched between two Plexiglas plates. Among the pure Mhcfs immobilized on a graphite electrode, iron(III) hexacyanoferrate (Prussian blue) exhibits the highest electrocatalytic effect, whereas in the composite electrodes chromium(III) hexacyanoferrate (Crhcf) shows the highest activity and best performance and reproducibility for the electrochemical reduction of H₂O₂. The Crhcf electrode provides a linear dependence on H₂O₂ concentration in the range 2.5 × 10⁻⁶ mol L⁻¹ (LOD) to 1 × 10⁻⁴ mol L⁻¹ (phosphate buffer, pH 7). The sensor was applied for the detection of H₂O₂ enzymatically produced by glucose oxidase. The optimal conditions for the peroxide injection were 2 min after the beginning of the reaction and 25 °C with a detection limit of 7.0 × 10⁻⁶ mol L⁻¹ for glucose.     

Preparation and electrocatalytic oxidation properties of a nickel pentacyanonitrosylferrate modified carbon composite electrode by two-step sol-gel technique: improvement of the catalytic activity

The sol-gel technique was used to construct nickel pentacyanonitrosylferrate (NiPCNF) modified composite ceramic carbon electrodes (CCEs). This involves two steps: forming a CCE containing Ni powder and then immersing the electrode into a sodium pentacyanonitrosyl-ferrate solution (electroless deposition). The cyclic voltammograms of the resulting surface modified CCE under optimum conditions show a well-defined redox couple due to the [Ni^IIFe^III/II(CN)₅NO]^0/−1 system. The electrochemical properties and stability of the modified electrode were investigated by cyclic voltammetry. The apparent electron transfer rate constant (k_s) and transfer coefficient (α) were determined by cyclic voltammetry being about 1.1 s⁻¹ and 0.55, respectively. Sulfite has been chosen as a model to elucidate the electrocatalytic ability of NiPCNF-modified CCE prepared by one- or two-step sol-gel technique. The modified electrode showed excellent electrocatalytic activity toward the SO₃²⁻ electro oxidation in pH range 3-9 in comparison with CCE modified by homogeneous mixture of graphite powder, Ni(NO₃)₂ and Na₂[Fe(CN)₅NO] (one-step sol-gel technique). Sulfite was determined amperometrically at the surface of this modified electrode in pH 7. Under the optimized conditions the calibration curve is linear in the concentration range 2 μM to 2.0 mM. The detection limit (signal-to-noise is 3) and sensitivity are 0.5 μM and 13.5 nA/μM. The modified carbon ceramic electrode containing nickel pentacyanonitrosylferrate shows good repeatability, short response time, t (90%) <2 s, long-term stability (3 months), and it is renewed by simple mechanical polishing and its immersing in Na₂[Fe(CN)₅NO] solution. The advantages of the SO₃²⁻ amperometrically detector based on the nickel pentacyanonitrosylferrate-doped CCE is high sensitivity, inherent stability at wide pH range, excellent catalytic activity and less expense and simplicity of preparation. This sensor can be used as amperometric detector in chromatographic instruments.     

Hydrogen evolution on RuxTi1−xO2 in 0.5 M H2SO4

Hydrogen evolution from 0.5 M H₂SO₄ on Ti electrodes coated with a Ru_xTi_1−xO₂ (x=0.04-0.5) layer has been studied by potentiostatic polarisation, cyclic voltammetry and ac-impedance spectroscopy. The results indicate that after a certain activation period the performance of such an electrode coating is comparable to platinum. The addition of small amounts of sodium molybdate increased the capacitance of the electrode and a reduction of the performance was observed. Increasing the temperature of the pure electrolyte from 20 to 75 °C caused an increase in the rate of the hydrogen evolution and in addition an increase of the electrode capacitance. The electrodes have been found to be rather tolerant to chloride and Fe²⁺ ions, and could hence be promising candidates as catalyst materials for solid polymer water electrolysis systems. From steady state measurements the Tafel slopes were found to change from −105 mV/decade for pure titanium to about −40 mV/decade for the (RuTi)O₂ coated electrodes. The exchange current densities were calculated from the steady state curves, as well as from impedance data, to be about 10⁻⁴ A cm⁻² after activation.     

Combination of redox capacity and double layer capacitance in composite electrodes through immobilization of an organic redox couple on carbon black

Carbon electrodes have been modified with 2-nitro-1-naphthol with the aim of producing composite supercapacitor electrodes, which make use of both the electric double layer (EDL) capacitance of high surface area carbon and the redox capacity (pseudocapacitance) of the organic compound. In situ FTIR and cyclic voltammetric data confirm literature reports of the reduction of 2-nitro-1-naphthol to 2-amino-1-naphthol and the subsequent oxidation of the o-aminonaphthol to the corresponding o-naphthaquinoneimine in aqueous acidic media. The measurements also show that the quinoneimine is not stable and hydrolized in sulphuric acid electrolyte to 1,2-naphthaquinone. The chemically highly reversible o-naphthaquinone/o-naphthahydroquinone couple remains immobilized on the carbon electrodes during redox cycling. The organic redox couple contributes a capacity of 35 mA h g⁻¹ of the bare carbon to the overall charge storage capability of the composite electrode. Surprisingly, it does not affect the capacitance of the electric double layer of the carbon. During 1000 charge/discharge cycles, the pseudocapacitance decreases by less than 20% in a normal large-volume electrochemical cell. Electrochemical impedance measurements show that the full capacity of the electrode is accessible at frequencies below 0.1 Hz.     

Voltammetric investigation of the dissociative electron transfer to polychloromethanes at catalytic and non-catalytic electrodes

The electrochemical behavior of CCl₄, CHCl₃ and CH₂Cl₂ has been investigated by cyclic voltammetry at glassy carbon and silver electrodes in DMF + 0.1 M Et₄NClO₄ in the absence and presence of a good proton donor. At both electrodes, each compound exhibits a series of reduction peaks which represent sequential hydrodechlorination steps up to methane. The nature of the electrode material and the proton availability of the medium affect drastically the voltammetric pattern of the compounds. Silver exhibits extraordinary electrocatalytic properties toward the reduction process, with positive shifts of the peak potentials of about 0.57-0.95 V as compared to glassy carbon. Reduction of any polychloromethane, CH_nCl_(4−n) (n = 0-2), yields the carbanion CH_nCl_(3−n)⁻ which partitions into two reaction channels: (i) protonation and (ii) Cl⁻ elimination to give a carbene :CH_nCl_(2−n). If a strong proton donor is added into the solution, sequential hydrodechlorination becomes the principal reaction route at both electrodes. When, instead, purposely added acid is not present in solution, both reaction pathways ought to be considered. In these conditions, when possible, self-protonation reactions play an important role in the overall reduction process.     

Micro-supercapacitors based on three dimensional interdigital polypyrrole/C-MEMS electrodes

Symmetric micro-supercapacitors with three dimensional (3D) interdigital electrode structures have been designed and fabricated through Carbon-microelectrochemical system (C-MEMS) technology. The micro-supercapacitor consists of a 3D C-MEMS structure which serves as a high effective surface area current collector and conformal polypyrrole (PPy) films deposited on the carbon structures as electroactive materials. The electrochemical performance of single electrodes and symmetric micro-supercapacitor cells were evaluated by cyclic voltammetry (CV) at different scan rates and galvanostatic charge/discharge tests. The effect of the 3D electrode structure on the performance of the micro-supercapacitor was studied. Single PPy/C-MEMS electrodes presented a specific capacitance of 162.07 ± 12.40 mF cm⁻² and a specific power of 1.62 ± 0.12 mW cm⁻² at 20 mV s⁻¹ scan rate. The symmetric micro-supercapacitor cells exhibited an average specific capacitance of 78.35 ± 5.67 mF cm⁻² and a specific power of 0.63 ± 0.04 mW cm⁻² at 20 mV s⁻¹ scan rate, demonstrating that 3D micro-supercapacitors are promising for applications that require high power in a limited footprint area of the device.     

Synergistic effect of a catechin-immobilized poly(3,4-ethylenedioxythiophene)-modified electrode on electrocatalysis of NADH in the presence of ascorbic acid and uric acid

Catechin is a polyphenolic flavonoid that can be isolated from a variety of natural sources, including tea leaves, grape seeds, and the wood and bark of trees such as acacia and mahogany. In our experiments, catechin was immobilized on PEDOT/GC (poly(3,4-ethylenedioxythiophene)/glassy carbon)-modified electrodes and used as a mediator for NADH (nicotinamide adenine dinucleotide) oxidation. The effect of the PEDOT thickness on the surface coverage of the catechin molecules was studied using cyclic voltammetry. The electrochemical properties and the effect of pH on the redox properties of the immobilized catechin molecules were studied by cyclic voltammetry in phosphate solution. The electrocatalytic oxidation of NADH at different electrode surfaces such as the bare GC-, the PEDOT/GC-, the catechin/GC- and the catechin/PEDOT/GC-modified electrodes was explored in phosphate solution at pH 7. In the catechin/PEDOT/GC-modified electrode, the PEDOT film plays an important role in resolving the oxidation potentials of ascorbic acid and NADH into two peaks that occur at the same potential for the catechin/GC-modified electrode surface. The heterogeneous electron transfer rate constant for NADH oxidation at the catechin/PEDOT/GC-modified electrode was determined using the rotating disk electrode technique and found to be 9.88 × 10³ M⁻¹ s⁻¹. The amperometric determination of NADH at the catechin/PEDOT/GC electrode was tested. The sensitivity of the electrode was 19 nA/μM.     

Self-assembled nano-arrays of single-walled carbon nanotube-octa(hydroxyethylthio)phthalocyaninatoiron(II) on gold surfaces: Impacts of SWCNT and solution pH on electron transfer kinetics

The construction by sequential self-assembly process of reproducible, highly stable and pH-responsive redox-active nanostructured arrays of single-walled carbon nanotubes (SWCNTs) integrated with octa(hydroxyethylthio)phthalocyaninatoiron(II) (FeOHETPc) via ester bonds on a gold surface (Au-Cys-SWCNT-FeOHETPc) is investigated and discussed. The successful construction of this electrode is confirmed using atomic force microscopy and X-ray photoelectron spectroscopy as well as from the distinct cyclic voltammetric and electrochemical impedance spectroscopic profiles. The Au-Cys-SWCNT-FeOHETPc electrode exhibited strong dependence on the reaction of the head groups and the pH of the working electrolytes, the surface pK_a is estimated as 7.3. The high electron transfer capability of the Au-Cys-SWCNT-FeOHETPc electrode over other electrodes (Au-Cys-SWCNT or the Au-Cys-FeOHETPc or the Au-FeOHETPc) suggests that SWCNT greatly improves the electronic communication between FeOHETPc and the bare gold electrode. The electron transfer rate constant (k_app) of Au-Cys-SWCNT-FeOHETPc in pH 4.8 conditions (∼1.7 × 10⁻² cm⁻² s⁻¹) over that of the electrode obtained from SWCNT integrated with tetraaminophthalocyninatocobalt(II) (Au-Cys-SWCNT-CoTAPc) (5.1 × 10⁻³ cm⁻² s⁻¹) is attributed to the possible effect of the central metal on the phthalocyanine core and substituents on the peripheral positions of the phthalocyanine rings. We also prove that aligned SWCNT arrays exhibit much faster electron transfer kinetics to redox-active species in solutions compared to the randomly dispersed (drop-dried) SWCNTs.     

Potentiometric stripping analysis of bismuth based on carbon paste electrode modified with cryptand [2.2.1] and multiwalled carbon nanotubes

An electrochemical method based on potentiometric stripping analysis (PSA) employing a cryptand [2.2.1] (CRY) and carbon nanotube (CNT) modified paste electrode (CRY-CNT-PE) has been proposed for the subnanomolar determination of bismuth. The characterization of the electrode surface has been carried out by means of scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and chronocoulometry (CC). It was observed that by employing CRY-CNT-PE, a 9-fold enhancement in the PSA signal (dt/dE) was observed as compared to plain carbon paste electrode (PCPE). Under the optimized conditions, dt/dE (s/V) was proportional to the Bi(III) concentration in the range of 5.55 × 10⁻⁸ to 9.79 × 10⁻¹¹ M (r = 0.9990) with the detection limit (S/N = 3) of 3.17 × 10⁻¹¹ M. The practical analytical utilities of the modified electrode were demonstrated by the determination of bismuth in pharmaceutical formulations, human hair, sea water, urine and blood serum samples. The prepared modified electrode showed several advantages, such as a simple preparation method, high sensitivity, very low detection limits and excellent reproducibility. Moreover, the results obtained for bismuth analysis in commercial and real samples using CRY-CNT-PE and those obtained by atomic absorption spectroscopy (AAS) are in agreement at the 95% confidence level.     

Fabrication of nickel oxide-embedded titania nanotube array for redox capacitance application

Titania nanotube array with an enlarged tube diameter of 110 nm and length of 700 nm was grown on titanium metal by a potentiostatic anodization in hydrofluoric acid-phosphoric acid-ethenyl glycol electrolyte. Nickel hydroxide was introduced into this titania nanotubes by either an electrodeposition-oxidation or hydrothermal process. Nickel oxide-titania composite was finally formed by heating treatment at 300 °C. Such a well-defined nanocomposite supported on titanium substrate was designed as a functional nanotube array electrode for the redox capacitance application. The morphology, microstructure and electrochemical properties of the nanocomposites were investigated by field emission scanning electron microscope, X-ray diffraction, energy dispersive X-ray diffraction and cyclic voltammetry measurements. It was found that nickel oxide could be embedded in titania nanotubes and extend from inner wall to top layer with an open pore mouth. The entire tube lengths were approx. 770 nm and 710 nm, meanwhile nickel-to-titanium atom ratios were determined as 9.6 at% and 36.4 at% for nickel oxide-embedded titania by an electrochemical and hydrothermal synthesis, respectively. The corresponding specific redox capacitance was also increased from 26 mF cm⁻² to 85 mF cm⁻² with highly reversible charge-discharge stability. Such an improvement was mostly ascribed to more accessible reaction interface of electroactive nickel oxide through its higher loading and a uniform dispersion on titania nanotubes. The capacitance was further increased up to 128 mF cm⁻² for 36.4 at% nickel-containing nickel oxide-titania/titanium electrode when a porous graphite carbon instead of a platinum sheet was used as a cathode.     

NiO-based composite electrode with RuO2 for electrochemical capacitors

NiO/RuO₂ composite materials were prepared for use in electrochemical capacitors (ECs) by co-precipitation method followed by heat treatment. X-ray diffraction (XRD) spectra indicated that no new structural materials were formed and ruthenium oxide particles were coated by NiO particles. RuO₂ partly introduced into NiO-based electrode had improved its electrochemical performance and capacitive properties by using electrochemical measurements. A maximum specific capacitance of 210 F/g was obtained for NiO-based composite electrode with 10 wt.% RuO₂ in the voltage range from −0.4 to 0.5 V in 1 mol/l KOH solution. By comparison of effect of modified modes on the specific capacitance, chemically modified composite electrodes had more stable cycling properties than those of physically modified electrodes. After 200 cycles, specific capacitance of NiO-based chemical composite electrode with 5 wt.% RuO₂ kept 95% above, while that of physical electrode was only 79% of initial specific capacitance.     

Voltammetric and electrochemical impedance spectroscopy characterization of a cathodic and anodic pre-treated boron doped diamond electrode

The effect of boron doped diamond (BDD) surface termination, immediately after cathodic and anodic electrochemical pre-treatments, on the electrochemical response of a BDD electrode in aqueous media and the influence of the different supporting electrolytes utilized in these pre-treatments on the final surface termination was investigated with [Fe(CN)₆]^4−/3−, as redox probe, by cyclic and differential pulse voltammetry and electrochemical impedance spectroscopy. The cyclic voltammetry results indicate that the electrochemical behavior for the redox couple [Fe(CN)₆]^4−/3− is very dependent on the state of the BDD surface, and a reversible response was observed after the cathodic electrochemical pre-treatment, whereas a quasi-reversible response occurred after anodic electrochemical pre-treatment. Differential pulse voltammetry in acetate buffer also showed that the potential window is very much influenced by the electrochemical pre-treatment of the BDD surface. Electroactivity of non-diamond carbon surface species (sp² inclusions) incorporated into the diamond structure was observed after cathodic and anodic pre-treatments. Electrochemical impedance spectroscopy confirmed the cyclic voltammetry results and indicates that the BDD surface resistance and capacitance vary significantly with the electrolyte and with the electrochemical pre-treatment, caused by different surface terminations of the BDD electrode surface.     

Electrochemical properties of porous bismuth electrodes

The properties of Bi surfaces with different roughnesses were characterized by electron microscopy, cyclic voltammetry, and impedance spectroscopy. Two different strategies were used for preparation of porous bismuth layers onto Bi microelectrode surface in aqueous 0.1 M LiClO₄ solution. Firstly, treatment at potential E < −2 V (vs. Ag|AgCl in sat. KCl) has been applied, resulting in bismuth hydride formation and decomposition into Bi nanoparticles which deposit at the electrode surface. Secondly, porous Bi layer was prepared by anodic dissolution (E = 1 V) of bismuth electrode followed by fast electroreduction of formed Bi³⁺ ions at cathodic potentials E = −2 V. The nanostructured porous bismuth electrode, with surface roughness factor up to 220, has negligible frequency dispersion of capacitance and higher hydrogen evolution overvoltage than observed for smooth Bi electrodes.