Synthesis and characterization of MoOx-Pt/C and TiOx-Pt/C nano-catalysts for oxygen reduction

The oxygen reduction reaction (ORR) was studied at carbon supported MoO_x-Pt/C and TiO_x-Pt nanocatalysts in 0.5 mol dm⁻³ HClO₄ solution, at 25 °C. The MoO_x-Pt/C and TiO_x-Pt/C catalysts were prepared by the polyole method combined by MoO_x or TiO_x post-deposition. Home made catalysts were characterized by TEM and EDX techniques. It was found that catalyst nanoparticles were homogenously distributed over the carbon support with a mean particle size about 2.5 nm. Quite similar distribution and particle size was previously obtained for Pt/C catalyst. Results confirmed that MoO_x and TiO_x post-deposition did not lead to a significant growth of the Pt nanoparticles.The ORR kinetics was investigated by cyclic voltammetry and linear sweep voltammetry at the rotating disc electrode. These results showed the existence of two E − log j regions, usually observed with polycrystalline Pt in acid solution. It was proposed that the main path in the ORR mechanism on MoO_x-Pt/C and TiO_x-Pt/C catalysts was the direct four-electron process with the transfer of the first electron as the rate-determining step. The increase in catalytic activity for ORR on MoO_x-Pt/C and TiO_x-Pt/C catalysts, in comparison with Pt/C catalyst, was explained by synergetic effects due to the formation of the interface between the platinum and oxide materials and by spillover due to the surface diffusion of oxygen reaction intermediates.     

Quantitative study of pH change during LaNi5−xAlx (x = 0, 0.3) discharge process by SECM

Oxygen reduction reaction (ORR) on Pt microelectrode was used for developing a micro pH sensor for scanning electrochemical microscopy (SECM) study in this work. When the potential of Pt microelectrode was held constant in ORR region, the ORR current (cathodic current) increased with decreasing solution pH and vice versa. The response time of the ORR current to pH changes was measured to be ca. 30 ms which implies that the pH response is fast enough for monitoring the temporal pH changes. Furthermore, a fine linear relationship was found to exist between the half wave potential of ORR (E_1/2) and the solution pH value, and the slope is −46 mV/pH. The Pt micro pH sensor was located 1 μm above the LaNi_5−xAl_x (x = 0, 0.3) substrate electrode surface in pH = 9 KOH solution to perform the tip-substrate voltammetry of SECM. In tip voltammogram, the ORR tip current qualitatively reflects the transit solution pH changes during LaNi_5−xAl_x discharge reaction. Also, the minimum values of the solution pH near LaNi₅ and LaNi_4.7Al_0.3 surface during the discharge reaction were quantitatively detected; they were 7.17 and 7.57, respectively. The result indicates that Al partial substitution for Ni degrades the maximum discharge ability of the alloy and decreases the hydrogen diffusion coefficient in alloy bulk.     

Oxygen reduction reaction on electrodeposited Pt100−x−yNixPdy thin films

The kinetics of the oxygen reduction reaction (ORR) were examined on a series of Pt_100−x−yNi_xPd_y ternary alloys. Films were produced by electrodeposition that involved a combination of underpotential and overpotential reactions. For Pt-rich Pt_100−x−yNi_xPd_y alloy films (x < 0.65) Ni co-deposition occurred at underpotentials while for Ni-rich films (x > 0.65) deposition proceeded at overpotentials. Rotating disk electrode (RDE) measurements of the ORR kinetics on Ni-rich Pt_100−x−yNi_xPd_y thin films revealed up to ∼6.5-fold enhancement of the catalytic activity relative to Pt films with the same Pt mass loading. More than half of the electrocatalytic gain may be attributed to surface area expansion due to Ni dealloying. Surface area normalization based on the H_upd charge reduced the enhancement factor to a value less than 2. The most active ternary alloy film for ORR was Pt₂₅Ni₇₃Pd₂. Comparison of the ORR on Pt, Pt₂₀Ni₈₀, Pt₂₅Ni₇₃Pd₂ thin films indicate that the binary alloy is the most active with a H_upd normalized ORR enhancement factor of up to 3.0 compared to 1.6 for the ternary alloy.     

Kinetics and PEMFC performance of RuxMoySez nanoparticles as a cathode catalyst

Kinetics of Ru_xMo_ySe_z nanoparticles dispersed on carbon powder was studied in 0.5 M H₂SO₄ electrolyte towards the oxygen reduction reaction (ORR) and as cathode catalysts for a proton exchange membrane fuel cell (PEMFC). Ru_xMo_ySe_z catalyst was synthesized by decarbonylation of transition-metal carbonyl compounds for 3 h in organic solvent. The powder was characterized by X-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. Catalyst is composed of uniform agglomerates of nanocrystalline particles with an estimated composition of Ru₆Mo₁Se₃, embedded in an amorphous phase. The electrochemical activity was studied by rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE) techniques. Tafel slopes for the ORR remain invariant with temperature at −0.116 V dec⁻¹ with an increase of the charge transfer coefficient in dα/dT = 1.6 × 10⁻³, attributed to an entropy turnover contribution to the electrocatalytic reaction. The effect of temperature on the ORR kinetics was analyzed resulting in an apparent activation energy of 45.6 ± 0.5 kJ mol⁻¹. The catalyst generates less than 2.5% hydrogen peroxide during oxygen reduction. The Ru_xMo_ySe_z nanoparticles dispersed on a carbon powder were tested as cathode electrocatalyst in a single fuel cell. The membrane-electrode assembly (MEA), included Nafion^® 112 as polymer electrolyte membrane and commercial carbon supported Pt (10 wt%Pt/C-Etek) as anode catalyst. It was found that the maximum performance achieved for the electro-reduction of oxygen was with a loading of 1.0 mg cm⁻² Ru_xMo_ySe_z 20 wt%/C, arriving to a power density of 240 mW cm⁻² at 0.3 V and 80 °C.     

Simulations and study of electrochemical hydrogen energy conversion in EasyTest Cell

An EasyTest Cell concept is applied to study the performance characteristics of the electrochemical processor for polymer electrolyte membrane electrochemical hydrogen energy converters (PEM EHEC), broadly known as a membrane electrode assembly (MEA). A series of MEAs consisting of Nafion 117 polymer electrolyte and magnetron sputtered Pt, IrO_x, and composite IrO_x/Pt/IrO_x catalysts with varying catalytic loadings were investigated. The partial electrode reactions proceeding in the real PEM EHEC, namely hydrogen oxidation (HOR), hydrogen evolution (HER), oxygen reduction (ORR), and oxygen evolution (OER), are simulated and studied in a recently developed test cell with a unitized gas compartment. The EasyTest Cell design gives possibilities for strict control of the experimental conditions by avoiding the usage of any auxilliary gas conditioning equipment. By varying the thickness of the sputtered Pt film, the catalyst loading is remarkably reduced (from 0.5 to 0.06 mg cm⁻² or about 8 times) for both HOR and HER without any sacrifice of the electrode performance. The electrode with 0.2 mg cm⁻² sputtered IrO_x shows the best OER performance. The composite IrO_x/Pt/IrO_x electrode demonstrated a bi-functional catalytic activity toward both OER and ORR, as well as improved gas diffusion properties toward ORR compared to the single Pt layer with the same catalytic loading.A phenomenological criterion for evaluating the gas diffusion properties of the electrodes is proposed. The applied testing approach is validated via comparison of the results obtained in the EasyTestCell and the common laboratory PEM electrolytic cell.     

Cobalt based non-precious electrocatalysts for oxygen reduction reaction in proton exchange membrane fuel cells

Cobalt based non-precious metal catalysts were synthesized using chelation of cobalt (II) by imidazole followed by heat-treatment process and investigated as a promising alternative of platinum (Pt)-based electrocatalysts in proton exchange membrane fuel cells (PEMFCs). Transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) measurements were used to characterize the synthesized CoN_x/C catalysts. The activities of the catalysts towards oxygen reduction reaction (ORR) were investigated by electrochemical measurements and single cell tests, respectively. Optimization of the heat-treatment temperature was also explored. The results indicate that the as-prepared catalyst presents a promising electrochemical activity for the ORR with an approximate four-electron process. The maximum power density obtained in a H₂/O₂ PEMFC is as high as 200 mW cm⁻² with CoN_x/C loading of 2.0 mg cm⁻².     

Effect of Pt addition on the isomerization properties of MoO2 − x(OH)y deposited on TiO2

Isomerization of n-hexane and n-pentane were studied using equivalent 5 monolayers of MoO₃ deposited on TiO₂. Addition of 2.5% Pt by weight of MoO₃ on the Mo catalyst resulted in an increase in the catalytic activity of the system in favor of hydrocracking products. Surface characterization by XPS-UPS and ISS reveal that the sample surface contains Oxygen, Molybdenum, Platinum and Titanium. Apparently, the metallic properties of the deposited Pt favors the hydrocracking reactions and becomes dominant at reaction temperatures higher than 623 K. Balanced metal-acid functions in MoO_2 − x(OH)_y phase seems to be in optimized condition toward the hydroisomerization process. The contribution of Platinum addition to this catalytic reaction is not obvious. Combination of surface XPS-UPS, ISS and catalytic reactions carried out at similar experimental conditions enabled us to have better insight concerning the catalytic activities of the different chemical species present on the sample surface.     

Oxygen reduction characteristics of several valve metal oxide electrodes in HClO4 solution

In the search for active cathode catalysts for polymer electrolyte fuel cells (PEFCs) using inexpensive materials, several valve metal oxide electrodes, TiO_x, ZrO_x, and TaO_x, with corresponding binary oxide electrodes were selected for the evaluation of catalytic activity for oxygen reduction reaction (ORR) by means of cyclic voltammetry in 0.1 M HClO₄ at 60 °C. These oxide electrodes were prepared mainly by the dip-coating method on a titanium plate substrate at a temperature between 400 °C and 500 °C and were characterized by scanning electron microscopy (SEM), X-ray diffractometry (XRD), and X-ray photoelectron spectroscopy (XPS). Among the oxide-coated electrodes investigated, Ti_0.7Zr_0.3O_x/Ti provided the highest ORR specific activity, with an onset potential, E_ORR, of 0.86 V vs. RHE during the cathodic potential sweep. Fine TaO_x particles prepared as an extension of the dip-coating method, showed very high catalytic activity determined by means of hydrodynamic voltammetry in 0.1 M HClO₄ at 30 °C with an E_ORR of 0.90 V vs. RHE.     

Tantalum (oxy)nitrides prepared using reactive sputtering for new nonplatinum cathodes of polymer electrolyte fuel cell

Tantalum (oxy)nitrides (TaO_xN_y) have been investigated as new cathodes for polymer electrolyte fuel cells without platinum. TaO_xN_y films were prepared using a radio frequency magnetron sputtering under Ar + O₂ + N₂ atmosphere at substrate temperatures from 50 to 800 °C. The effect of the substrate temperature on the catalytic activity for the oxygen reduction reaction (ORR) and properties of the TaO_xN_y films were examined. The catalytic activity of the TaO_xN_y for the ORR increased with the increasing substrate temperature. The ORR current density at 0.4 V vs. RHE on TaO_xN_y prepared at 800 °C was approximately 20 times larger than that on TaO_xN_y prepared at 50 °C. The onset potential of the TaO_xN_y for the ORR was obtained at the ORR current density of −0.2 μA cm⁻². The onset potential of the TaO_xN_y prepared at 800 °C was ca. 0.75 V vs. RHE. The X-ray diffraction patterns revealed that Ta₃N₅ structure grew as the substrate temperature increased. While, the ionization potentials of all specimens were lower than that of Ta₃N₅, and decreased with the increasing substrate temperature. The TaO_xN_y which had Ta₃N₅ structure and lower ionization potential might have a definite catalytic activity for the ORR.     

Influence of sputtering power on oxygen reduction reaction activity of zirconium oxides prepared by radio frequency reactive sputtering

Zirconium oxides (ZrO_2−x) have been investigated as new cathodes for direct methanol fuel cells without platinum. ZrO_2−x films were prepared using a radio frequency (RF) magnetron sputtering at RF powers from 75 to 175 W. The influence of the RF power on the catalytic activity for the oxygen reduction reaction (ORR) and properties of the ZrO_2−x films were examined. The ORR activity of the ZrO_2−x catalyst increased with the RF power in the range we studied. The onset potential for ORR over ZrO_2−x deposited at 175 W was 0.88 V vs RHE. In addition, the relationship between the ORR activity and the composition, crystallinity, electric conductivity, as well as the ionization potential has been investigated. The zirconium oxide with an oxygen defected state and the higher electric conductivity showed the higher ORR activity, and the electrocatalytic activity for ORR increased with the decreasing in the ionization potential of the ZrO_2−x catalyst.     

Preparation, testing and modeling of three-dimensionally ordered catalytic layers for electrocatalysis of fuel cell reactions

The arrays of vertically aligned carbon nano-filaments (VACNF) were synthesized by catalytic chemical vapor deposition on TiO_x substrates, obtained via oxidative treatment of polycrystalline Ti and Ti thin films on Si(1 0 0). VACNF were studied using scanning and transmission electron microscopies. The Pt deposition on VACNF was utilized to prepare a set of model catalysts, which were investigated in two fuel cell related reactions: the oxygen reduction (ORR) and the hydrogen oxidation (HOR) reactions. The experimental data were compared with the results of mathematical modeling performed for a fast (quasi)reversible and a slow irreversible electrochemical reaction. The approach made it possible to study electrochemical reactions (HOR, ORR) on nano-materials under well defined mass transport conditions. The influence of the catalytic layer thickness and the Pt coverage on the penetration depth of the reactive species inside the layer and consequently on the performance and on the Pt effectiveness factor were analyzed.     

Controlled growth and shape formation of platinum nanoparticles and their electrochemical properties

Cubic Pt nanoparticles were prepared from a solution of K₂PtCl₄ containing sodium polyacrylate as a capping reagent. The effects of the Pt/polymer molar ratio, the average molecular weight (M_w) of the polymer, and reaction temperature on the shape and size were investigated. When the polymer of M_w = 5100 was added at a molar ratio of Pt/polymer = 1/12, cubic platinum nanoparticles of an average size of 10.3 nm were predominantly formed (ca. 50% in number) at 25 °C. The electron diffraction pattern of the cubic nanoparticles revealed that they are single crystals with Pt {1 0 0} faces on the surface.The cubic nanoparticles were electrochemically active, and showed strong features of Pt {1 0 0} faces on cyclic voltammogram under argon atmosphere. After repeated potential cycling in the range 0.05-1.4 V, the features of Pt {1 0 0} were gradually lost, and changed to those of polycrystalline Pt. Rotating ring disk electrode measurements in O₂-saturated H₂SO₄ solution revealed that the cubic nanoparticles had a high catalytic activity for oxygen reduction reaction (ORR). After polycrystallization by repeated potential cycling, the activity for ORR and hydrogen peroxide formation decreased slightly, which were attributed to the surface structural change from Pt {1 0 0} to polycrystalline.     

Hydrogen spillover phenomenon: Enhanced reversible hydrogen adsorption/desorption at Ta2O5-coated Pt electrode in acidic media

The current study is concerned with the preparation and characterization of tantalum oxide-loaded Pt (TaO_x/Pt) electrodes for hydrogen spillover application. XPS, SEM, EDX and XRD techniques are used to characterize the TaO_x/Pt surfaces. TaO_x/Pt electrodes were prepared by galvanostatic electrodeposition of Ta on Pt from LiF-NaF (60:40 mol%) molten salts containing K₂TaF₇ (20 wt%) at 800 °C and then by annealing in air at various temperatures (200, 400 and 600 °C). The thus-fabricated TaO_x/Pt electrodes were compared with the non-annealed Ta/Pt and the unmodified Pt electrodes for the hydrogen adsorption/desorption (H_ads/H_des) reaction. The oxidation of Ta to the stoichiometric oxide (Ta₂O₅) increases with increasing the annealing temperature as revealed from XPS and X-ray diffraction (XRD) measurements. The higher the annealing temperature the larger is the enhancement in the H_ads/H_des reaction at TaO_x/Pt electrode. The extraordinary increase in the hydrogen adsorption/desorption at the electrode annealed at 600 °C is explained on the basis of a hydrogen spillover-reverse spillover mechanism. The hydrogen adsorption at the TaO_x/Pt electrode is a diffusion-controlled process.     

CoPdx oxygen reduction electrocatalysts for polymer electrolyte membrane and direct methanol fuel cells

The electrochemical activity of carbon-supported cobalt-palladium alloy electrocatalysts of various compositions have been investigated for the oxygen reduction reaction in a 5 cm² single cell polymer electrolyte membrane fuel cell. The polarization experiments have been conducted at various temperatures between 30 and 60 °C and the reduction performance compared with data from a commercial Pt catalyst under identical conditions. Investigation of the catalytic activity of the CoPd_x PEMFC system with varying composition reveals that a nominal cobalt-palladium atomic ratio of 1:3, CoPd₃, exhibits the best performance of all studied catalysts, exhibiting a catalytic activity comparable to the commercial Pt catalyst. The ORR on CoPd₃ has a low activation energy, 52 kJ/mol, and a Tafel slope of approximately 60 mV/decade, indicating that the rate-determining step is a chemical step following the first electron transfer step and may involve the breaking of the oxygen bond. The CoPd₃ catalyst also exhibits excellent chemical stability, with the open circuit cell voltage decreasing by only 3% and the observed current decreasing by only 10% at 0.8 V over 25 h. The CoPd₃ catalyst also exhibits superior tolerance to methanol crossover poisoning than Pt.     

A novel nanocomposite catalytic cathode for direct methanol fuel cells

We report a new nanocomposite catalytic cathode composed of iron phthalocyanine, platinum, carbon black and Nafion^® (FePc-Pt/C-Nafion^®) which exhibited enhanced catalytic activity for the oxygen reduction reaction (ORR) in the presence of methanol compared with usual Pt/C based electrodes. The catalytic cathode was prepared by depositing Pt colloidal nanoparticles (d_av = 2.2 nm) on a FePc/C support to form a FePc-Pt/C powder and ultrasonically treating a mixture of Nafion^® and the FePc-Pt/C powder in ethanol, followed by loading the mixture on a glassy carbon electrode and drying at 120 °C. In an O₂-saturated H₂SO₄ solution (0.5 M) with methanol (0.5 M), the onset potential (0.92 V vs RHE) over the FePc-Pt/C-Nafion^® electrode shifted by more than 240 mV toward positive relative to that over an electrode prepared with a commercial Pt/C catalyst and Nafion^®. A new kind of catalytic sites constructed by FePc nanocrystals and Pt nanoparticles was found in the FePc-Pt/C-Nafion^® electrode for the first time, which exhibited higher specific activity for ORR than Pt as calculated based on the hydrogen desorption charge.     

Preparation and oxygen reduction activity of stable RuSex/C catalyst with pyrite structure

Carbon supported RuSe_x (x = 0.35-2) catalysts of controlled stoichiometry and phase are synthesized via precipitating ruthenium nanoparticles on Vulcan XC-72R, then selenizing ruthenium with hydrogen annealing. The competition for Se between solid-state Ru selenization and volatile selenium hydride formation results in RuSe_x nanoparticles with the pyrite structure, the Ru hcp structure, or a mixture of the two. These catalysts are methanol tolerant, and catalytically active toward oxygen reduction reaction (ORR). RuSe_x/C (x ≅ 2) with a pyrite structure, produced at 400 °C, exhibits catalytic activity and stability superior to that of RuSe_x/C with a ruthenium hcp structure or a mixed phase. And this pyrite RuSe_x/C (x ≅ 2) catalyst yields H₂O₂ less than 1.5% in the technically pertinent potential range of 0.4-0.6 V (vs. Ag/AgCl). Its stability is verified in 100 CV cycles, which shows that the catalyst annealed at 400 °C is more enduring in potential cycling over 0.65 V (vs. Ag/AgCl), compared with the RuSe_x/C catalyst annealed at 300 °C and the RuSe_cluster/C reference catalyst prepared by thermolysis of Ru₃(CO)₁₂. After CV cycles, the 400 °C-annealed catalyst still exhibits a higher ORR activity than the other two catalysts.     

Ethanol electrooxidation on novel carbon supported Pt/SnOx/C catalysts with varied Pt:Sn ratio

Novel carbon supported Pt/SnO_x/C catalysts with Pt:Sn atomic ratios of 5:5, 6:4, 7:3 and 8:2 were prepared by a modified polyol method and characterized with respect to their structural properties (X-ray diffraction (XRD) and transmission electron microscopy (TEM)), chemical composition (XPS), their electrochemical properties (base voltammetry, CO_ad stripping) and their electrocatalytic activity and selectivity for ethanol oxidation (ethanol oxidation reaction (EOR)). The data show that the Pt/SnO_x/C catalysts are composed of Pt and tin oxide nanoparticles with an average Pt particle diameter of about 2 nm. The steady-state activity of the Pt/SnO_x/C catalysts towards the EOR decreases with tin content at room temperature, but increases at 80 °C. On all Pt/SnO_x/C catalysts, acetic acid and acetaldehyde represent dominant products, CO₂ formation contributes 1-3% for both potentiostatic and potentiodynamic reaction conditions. With increasing potential, the acetaldehyde yield decreases and the acetic acid yield increases. The apparent activation energies of the EOR increase with tin content (19-29 kJ mol⁻¹), but are lower than on Pt/C (32 kJ mol⁻¹). The somewhat better performance of the Pt/SnO_x/C catalysts compared to alloyed PtSn_x/C catalysts is attributed to the presence of both sufficiently large Pt ensembles for ethanol dehydrogenation and C-C bond splitting and of tin oxide for OH generation. Fuel cell measurements performed for comparison largely confirm the results obtained in model studies.     

Polypyrrole and La1−xSrxMnO3 (0≤ x ≤0.4) composite electrodes for electroreduction of oxygen in alkaline medium

Composite G/PPy/PPy(La_1−xSr_xMnO₃)/PPy electrodes made of the perovskite La_1−xSr_xMnO₃ embedded into a polypyrrole (PPy) layer, sandwiched between two pure PPy films, electrodeposited on a graphite support were investigated for electrocatalysis of the oxygen reduction reaction (ORR). PPy and PPy(La_1−xSr_xMnO₃) (0≤ x ≤0.4) successive layers have been obtained on polished and pretreated graphite electrodes following sequential electrodeposition technique. The electrolytes used in the electrodeposition process were Ar saturated 0.1 mol dm⁻³ pyrrole (Py) plus 0.05 mol dm⁻³ K₂SO₄ with and without containing a suspension of 8.33 g L⁻¹ oxide powder. Films were characterized by XRD, SEM, linear sweep voltammetry, cyclic voltammetry (CV) and electrochemical impedance (EI) spectroscopy. Electrochemical investigations were carried out at pH 12 in a 0.5 mol dm⁻³ K₂SO₄ plus 5 mmol dm⁻³ KOH, under both oxygenated and deoxygenated conditions. Results indicate that the porosity of the PPy matrix is considerably enhanced in presence of oxide particles. Sr substitution is found to have little influence on the electrocatalytic activity of the composite electrode towards the ORR. However, the rate of oxygen reduction decreases with decreasing pH of the electrolyte from pH 12 to pH 6. It is noteworthy that in contrast to a non-composite electrode of the same oxide in film form, the composite electrode exhibits much better electrocatalytic activity for the ORR.     

Synthesis of negative thermal expansion materials ZrW2−xMoxO8 (0 ≤ x ≤ 2) using hydrothermal method

Negative thermal expansion materials ZrW_2−xMo_xO₈ (0 ≤ x ≤ 2) have been successfully synthesized by the reaction of a mixture of ammonium tungstate and ammonium molybdate with zirconium oxynitrate using a hydrothermal method. Effect of substituted ion Mo on the microstructure, α-to-β and cubic to trigonal phase transition in resulting ZrW_2−xMo_xO₈ powders was examined by the XRD experiments. It was found that the structural phase transition temperature decreased slightly with increasing substituted content. The cubic to trigonal phase transition was also influenced by substituted content. The resulting products decomposed to WO₃/MoO₃ and ZrO₂ as temperature increasing when x ≤ 0.5 and while x > 0.5, the cubic phase transited to trigonal phase. The effect of substituted Mo on the morphology of resulting products was also investigated by SEM experiments.     

Electroreduction of dioxygen (ORR) in alkaline medium on Ag/C and Pt/C nanostructured catalysts—effect of the presence of methanol

Ag/C catalysts with different loading were prepared using a colloidal route to obtain well dispersed catalysts on carbon, with a particle size close to 15 nm. An amount of 20 wt.% Ag on carbon was found to be the best loading in terms of current density and mass activity. The 20 wt.% Ag/C catalyst was then studied and the kinetics towards ORR was determined and compared with that of a 20 wt.% Pt/C catalyst. The number of exchanged electrons for the ORR was found to be close to four with the rotating disk electrode (RDE) as well as with the rotating ring disc electrode (RRDE) techniques. From the RDE results, the Tafel slopes b, the diffusion limiting current density inside the catalytic film (j_l^film) and the exchange current density (j₀) were evaluated. The Tafel slopes b and diffusion limiting current densities inside the catalytic film (j_l^film) were found to be in the same order for both catalysts, whereas the exchange current density (j₀), which is a suitable estimation of the activity of the catalyst, was at least 10 times higher at the Pt/C catalyst than at the Ag/C catalyst. The behavior of both catalysts in methanol containing electrolyte was investigated and it was found that at a low methanol concentration, the Pt/C catalyst was quasi-tolerant to methanol. But, at a high methanol concentration, the ORR at a Pt/C was affected. However, the Pt/C catalyst showed in each case better activity towards ORR than the Ag/C catalyst, even if the latter one was less affected by the presence of methanol than the former one.