In situ transmission FTIR spectroelectrochemistry: A new technique for studying lithium batteries

In situ transmission FTIR spectra are measured during the electrochemical insertion of lithium into phospho-olivine FePO₄. The spectroelectrochemical cell consists of a composite FePO₄ cathode, a lithium metal anode, and an electrolyte of 1 M LiPF₆ in a 1:1 mixture of ethylene carbonate and diethyl carbonate (EC-DEC). Bands belonging to the electrolyte and cathode are identified in the infrared spectra of the in situ cells. The antisymmetric PO₄³⁻ bending vibrations (ν₄) are used to monitor Li⁺ insertion into FePO₄. Discharging produces spectral changes that are consistent with the formation of phospho-olivine LiFePO₄, yet the electrolyte bands are not affected by the discharging process. The in situ infrared experiments confirm the two-phase mechanism for lithium insertion into FePO₄. Moreover, the experiments demonstrate the ability to collect in situ transmission FTIR spectra of functioning electrode materials in lithium batteries. Unfortunately, lithium plating occurs on the optical window when the Li//FePO₄ half-cells are charged. The use of an intercalation anode such as graphite could alleviate this problem; however, this avenue of research is not explored in this study.     

Synthesis and characterization of high-density LiFePO4/C composites as cathode materials for lithium-ion batteries

To achieve a high-energy-density lithium electrode, high-density LiFePO₄/C composite cathode material for a lithium-ion battery was synthesized using self-produced high-density FePO₄ as a precursor, glucose as a C source, and Li₂CO₃ as a Li source, in a pipe furnace under an atmosphere of 5% H₂-95% N₂. The structure of the synthesized material was analyzed and characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical properties of the synthesized LiFePO₄/carbon composite were investigated by cyclic voltammetry (CV) and the charge/discharge process. The tap-density of the synthesized LiFePO₄/carbon composite powder with a carbon content of 7% reached 1.80 g m⁻³. The charge/discharge tests show that the cathode material has initial charge/discharge capacities of 190.5 and 167.0 mAh g⁻¹, respectively, with a volume capacity of 300.6 mAh cm⁻³, at a 0.1C rate. At a rate of 5C, the LiFePO₄/carbon composite shows a high discharge capacity of 98.3 mAh g⁻¹ and a volume capacity of 176.94 mAh cm⁻³.     

Morphological solution for enhancement of electrochemical kinetic performance of LiFePO4

LiFePO₄/C nanosheet composite has been prepared via a low-temperature solvothermal reaction followed by high-temperature treatment. The as-prepared sample is characterized by XRD, FTIR, Raman, SEM, and TEM. It is confirmed that the nanosheets are composed of ca. 50 nm thickness of crystalline LiFePO₄-core coated with ca. 10 nm thickness of carbon-shell. The charge-discharge tests show that the as-fabricated LiFePO₄/C nanosheet cathode in lithium-ion cell demonstrates high reversible capacity (164 mAh g⁻¹ at 0.1 C) and good cycle stability (columbic efficiency 100% during 100 cycles). The cyclic voltammetric analysis indicates Li⁺ diffusion determines the whole electrode reaction kinetics, and the diffusion coefficient estimated by EIS is comparable to the reported data. The enhanced kinetic behavior of the as-fabricated cathode is actually originated from the nano-dimensional sheet-like morphology, which facilitates Li⁺ migration due to the shortened diffusion distance, and simultaneously increased exchangeable Li⁺ amount considering more accessible active surface. In addition, the uniformly coated thin conductive carbons contribute a lot for this enhancement because of considerably improved electronic conductivity.     

Cycling-induced stress in lithium ion negative electrodes: LiAl/LiFePO4 and Li4Ti5O12/LiFePO4 cells

In this work, we examined the electrochemical behaviour of lithium ion batteries containing lithium iron phosphate as the positive electrode and systems based on Li-Al or Li-Ti-O as the negative electrode. These two systems differ in their potential versus the redox couple Li⁺/Li and in their morphological changes upon lithium insertion/deinsertion. Under relatively slow charge/discharge regimes, the lithium-aluminium alloys were found to deliver energies as high as 438 Wh kg⁻¹ but could withstand only a few cycles before crumbling, which precludes their use as negative electrodes. Negative electrodes consisting solely of aluminium performed even worse. However, an electrode made from a material with zero-strain associated to lithium introduction/removal such as a lithium titanate spinel exhibited good performance that was slightly dependent on the current rate used. The Li₄Ti₅O₁₂/LiFePO₄ cell provided capacities as high as 150 mAh g⁻¹ under C-rate in the 100th cycle.     

Carbon coated Li3V2(PO4)3 cathode material prepared by a PVA assisted sol-gel method

Carbon coated Li₃V₂(PO₄)₃ cathode material was prepared by a poly(vinyl alcohol) (PVA) assisted sol-gel method. PVA was used both as the gelating agent and the carbon source. XRD analysis showed that the material was well crystallized. The particle size of the material was ranged between 200 and 500 nm. HRTEM revealed that the material was covered by a uniform surface carbon layer with a thickness of 80 Å. The existence of surface carbon layer was further confirmed by Raman scattering. The electrochemical properties of the material were investigated by charge-discharge cycling, CV and EIS techniques. The material showed good cycling performance, which had a reversible discharge capacity of 100 mAh g⁻¹ when cycled at 1 C rate. The apparent Li⁺ diffusion coefficients of the material ranged between 9.5 × 10⁻¹⁰ and 0.9 × 10⁻¹⁰ cm² s⁻¹, which were larger than those of olivine LiFePO₄. The large lithium diffusion coefficient of Li₃V₂(PO₄)₃ has been attributed to its special NASICON-type structure.     

Synthesis, characterization and electrochemical performance of mesoporous FePO4 as cathode material for rechargeable lithium batteries

Mesoporous FePO₄ could deliver enhanced specific capacity of 160 mAh g⁻¹ at first discharge process, 90% of theoretical capacity of pure FePO₄, and 135 mAh g⁻¹ in the following cycles at 0.1 C rate. At 1 and 3 C rates, the capacities are 110 and 85 mAh g⁻¹, respectively, which is much higher than that of previously reported for modified FePO₄ materials. Electrochemical impedance spectroscopy (EIS) tests proved that mesoporous structure in FePO₄ materials enhanced the lithium ion intercalation/deintercalation kinetics as indicated by smaller charge transfer resistance (R_ct) of these materials. These results revealed that this mesoporous electrode material can be a potential candidate for high-power energy conversion devices.     

Kinetic analysis on LiFePO4 thin films by CV, GITT, and EIS

LiFePO₄ thin films were deposited on Ti substrates by pulsed laser deposition (PLD). The apparent chemical diffusion coefficients of lithium in the films, , were measured by cyclic voltammetry (CV), galvanostatic intermittent titration technique (GITT), and electrochemical impedance spectroscopy (EIS). The average values calculated from CV results were in the order of 10⁻¹⁴ cm² s^–1. The values obtained by GITT, and EIS techniques were in the range of 10^–14–10^–18 cm² s^–1, 10^–14–10^–18 cm² s^–1, respectively. The values obtained by the two methods show a minimum point at x ∼ 0.5 for Li_1−xFePO₄. However, the overpotential values of the LiFePO₄ thin film electrodes obtained from the GITT results and the diffusion impedance deduced from the impedance spectra also show the minimum values at x ∼ 0.5 for Li_1–xFePO₄. This contradict could be caused by the improper use of GITT and EIS techniques for measuring the chemical diffusion coefficient of Li in Li_1–xFePO₄ which constitutes two phase, i.e., LiFePO₄ and FePO₄ in this region.     

Impedance study of protecting film formation on lithium and lithiated graphite induced by bis(fluorosulfonyl) imide anion

The process of Li⁺ reduction from room temperature ionic liquids consisting of N-methyl-N-propylpyrrolidinium cation (MPPyr⁺) and bis(fluorosulfonyl) imide (FSI⁻) or bis(trifluoromethanesulfonyl) imide (TFSI⁻) anions was studied with the use of impedance spectroscopy. Reduction was carried out on both metallic lithium (Li) and graphite (G) electrodes. It has been found that the FSI anion in high amounts is able to form a protective film on both graphite and metallic lithium. The Li⁺/Li couple should rather be represented by a Li⁺/SEI/Li system. The SEI structure depends on the manner of its formation (chemical or electrochemical) and is not stable with time. The rate constant for the Li⁺ + e⁻ → Li process at the Li/SEI/Li⁺ (in MPPyrFSI) interface is k_o = 4.2 × 10⁻⁵ cm/s. In the case of carbon electrodes (G/SEI/Li⁺ interface), lithium diffusion in solid graphite is the rate determining step, reducing current by ca. two orders of magnitude, from ca. 10⁻⁴ A/cm², characteristic of the Li/SEI/Li⁺ electrode, to ca. 10⁻⁶ A/cm².     

Electrochemical behavior of lithium intercalated in a molybdenum disulfide-crown ether nanocomposite

A new nanocomposite, obtained from the intercalation of the cyclic ether 12-Crown-4 into MoS₂, Li_0.32MoS₂(12-Crown-4)_0.19, is described. The laminar product has an interlaminar distance of 14.4 Å. The electrical conductivity of the nanocomposite varies from 2.5 × 10⁻² to 4.3 × 10⁻² S cm⁻¹ in the range 25-77 °C, being about four times higher than the analogous poly(ethylene oxide) (PEO) derivative at room temperature. The electrochemical step-wise galvanostatic intercalation or de-intercalation of lithium, leading to Li_xMoS₂(12-Crown-4)_0.19 with x in the range 0.07-1.0, indicates a Li/Li⁺ pair average potential of 2.8 V. The electrochemical lithium diffusion coefficients in the crown ether intercalates, determined by galvanostatic pulse relaxation between 15 and 37 °C at different lithium intercalation degrees, are higher than those of the PEO derivatives under similar conditions, being however the diffusion mechanism rather more complex. The variation of both, the lithium diffusion activation enthalpy and the quasi-equilibrium potentials, with the lithium content shows there are two different limit behaviors, at low and high lithium intercalation degree, respectively. These features are discussed by considering the high stability of the Li-crown ether complex and the different chemical environments found by lithium along the intercalation process.     

Preparation and characterization of nano-particle LiFePO4 and LiFePO4/C by spray-drying and post-annealing method

Pure, nano-sized LiFePO₄ and LiFePO₄/C cathode materials are synthesized by spray-drying and post-annealing method. The influence of the sintering temperature and carbon coating on the structure, particle size, morphology and electrochemical performance of LiFePO₄ cathode material is investigated. The optimum processing conditions are found to be thermal treatment for 10 h at 600 °C. Compared with LiFePO₄, LiFePO₄/C particles are smaller in size due to the inhibition of crystal growth to a great extent by the presence of carbon in the reaction mixture. And that the LiFePO₄/C composite coated with 3.81 wt.% carbon exhibits the best electrode properties with discharge capacities of 139.4, 137.2, 133.5 and 127.3 mAh g⁻¹ at C/5, 1C, 5C and 10C rates, respectively. In addition, it shows excellent cycle stability at different current densities. Even after 50 cycles at the high current density of 10C, a discharge capacity of 117.7 mAh g⁻¹ is obtained (92.4% of its initial value) with only a low capacity fading of 0.15% per cycle.     

A comparative study of electrochemical properties of two kinds of carbon nanotubes as anode materials for lithium ion batteries

Two kinds of carbon nanotubes (CNTs), i.e., short carbon nanotubes (CNTs-1) synthesized by co-pyrolysis method and long carbon nanotubes (CNTs-2) produced using common CVD technique were comparatively investigated as anode materials for lithium ion batteries via transmission electron microscope (TEM), high-resolution TEM and a variety of electrochemical testing techniques. The test results showed that the reversible capacities of CNTs-1 electrode were 266 and 170 mAh g⁻¹ at the current densities of 0.2 and 0.8 mA cm⁻², respectively, which were almost twice those of CNTs-2 electrode. The larger voltage hysteresis in CNTs-2 electrode was not only related to the surface functional groups on CNTs, but also to the surface resistance of CNTs, which results in greater hindrance and higher overvoltage during lithium extraction from electrode. The kinetics properties of these two CNTs electrodes were compared by AC impedance measurements. It was found that, both the surface film and charge-transfer resistances of CNTs-1 were significantly lower than those of CNTs-2; the lithium diffusion coefficient (D_Li) of both CNTs electrodes decreased as the drop of voltage, but the magnitude of the D_Li variation of CNTs-1 electrode was smaller than that of CNTs-2 electrode, indicating CNTs-1 exhibited higher electrochemical activity and more favorable kinetic properties during charge and discharge process.     

One-step microwave synthesis and characterization of carbon-modified nanocrystalline LiFePO4

The precursors of LiFePO₄ were prepared by a sol-gel method using lithium acetate dihydrate, ferrous sulfate, phosphoric acid, citric acid and polyethylene glycol as raw materials, and then the carbon-modified nanocrystalline LiFePO₄ (LiFePO₄/C) cathode material was synthesized by a one-step microwave method with the domestic microwave oven. The effect of microwave time and carbon content on the performance of the resulting LiFePO₄/C material was investigated. Structural characterization by X-ray diffraction and scanning electron microscopy proved that the olivine phase LiFePO₄ was synthesized and the grain size of the samples was several hundred nanometers. Under the optimal conditions of microwave time and carbon content, the charge-discharge performance indicated that the nanosized LiFePO₄/C had a high electrochemical capacity at 0.2 C (152 mAh g⁻¹) and improved capacity retention; the exchange current density was 1.6977 mA cm⁻². Furthermore, the rate capability was improved effectively after LiFePO₄ was modified with carbon, with 59 mAh g⁻¹ being obtained at 20 C.     

Analysis of the chemical diffusion coefficient of lithium ions in Li3V2(PO4)3 cathode material

The chemical diffusion coefficients of lithium ions (DLi⁺) in Li₃V₂(PO₄)₃ between 3.0 and 4.8 V are systematically determined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic intermittent titration technique (GITT). The DLi⁺ values are found to be dependent on the voltage state of charge and discharge. Based on the results from all the three techniques, the true diffusion coefficients measured in single-phase region are in the range of 10⁻⁹ to 10⁻¹⁰ cm² s⁻¹. Its apparent diffusion coefficients measured in two-phase regions by CV and GITT range from 10⁻¹⁰ to 10⁻¹¹ cm² s⁻¹ and 10⁻⁸ to 10⁻¹³ cm² s⁻¹, respectively, depending on the potentials. By the GITT, the DLi⁺ varies non-linearly in a “W” shape with the charge-discharge voltage, which is ascribed to the strong interactions of Li⁺ with surrounding ions. Finally, the chemical diffusion coefficients of lithium ions measured by CV, EIS and GITT are compared to each other.     

Effect of lithium extraction on the stabilities,electrochemical properties,and bonding characteristics of LiFePO4 cathode materials: A first-principles investigation

The impact of lithium extraction on the structural stabilities, electronic structures, bonding characteristics, and electrochemical performances of LiFePO₄ compound was investigated by first-principles technique. The results demonstrated that the partition scheme of electrons not only affects the calculated atomic charges but also the magnetic properties. In FePO₄ and LiFePO₄ compounds, all Fe ions take high spin arrangements and have large magnetic moments (MMs), while the MMs of other ions are very small. The magnetisms of Li_xFePO₄ compounds are mainly originated form Fe ions. It was found that the changes in d band electrons of the transition metals do play an important role in determining the voltage of a battery (versus Li/Li⁺). Furthermore, the variations in d band electrons also provide us a method to control the density of states (DOS) and carrier concentration at the Fermi energy. Our calculations confirmed that the substitution of Fe by Co and Ni ions leads to a voltage increase by about 0.70 V and 1.23 V respectively. According to the bond populations, it can be identified that strong covalent bonds are formed between O and P ions. The P–O bonds are much stronger than Fe–O ones. The partial DOSs further revealed that the covalent bonds in Li_xFePO₄ are derived from the orbital overlaps between O_2s,2p and P_3s,3p states, and the overlap between Fe_3d and O_2p states. Such covalent bonds are of particularly importance for the excellent thermodynamic stabilities of the two-ends structures of Li_xFePO₄.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Improving the rate performance of LiFePO4 by Fe-site doping

LiFePO₄ doped by bivalent cation in Fe-sites show improved rate performance and cyclic stability. Under 10 C rate at room temperature, the capacities of LiFe_0.9M_0.1PO₄ (M = Ni, Co, Mg) maintain at 81.7, 90.4 and 88.7 mAh/g, respectively, in comparison with 53.7 mAh/g for undoped LiFePO₄ and 54.8 mAh/g for carbon-coated LiFePO₄ (LiFePO₄/C). The capacity retention is 95% after 100 cycles for doped samples while this value is only 70% for LiFePO₄ and LiFePO₄/C. Such a significant improvement in electrochemical performance should be partially related to the enhanced electronic conductivities (from 2.2 × 10⁻⁹ to <2.5 × 10⁻⁷ S cm⁻¹) and probably the mobility of Li⁺ ions in the doped samples.     

Electrochemical behavior of LiCoO2 in a saturated aqueous Li2SO4 solution

The electrochemical behavior of a commercial LiCoO₂ with spherical shape in a saturated Li₂SO₄ aqueous solution was investigated with cyclic voltammetry and electrochemical impedance spectroscopy. Three redox couples at E_SCE = 0.87/0.71, 0.95/0.90 and 1.06/1.01 V corresponding to those found at ELi/Li⁺=4.08/3.83, 4.13/4.03 and 4.21/4.14 V in organic electrolyte solutions were observed. The diffusion coefficient of lithium ions is 1.649 × 10⁻¹⁰ cm² s⁻¹, close to the value in organic electrolyte solutions. The results indicate that the intercalation and deintercalation behavior of lithium ions in the Li₂SO₄ solution is similar to that in the organic electrolyte solutions. However, due to the higher ionic conductivity of the aqueous solution, current response and reversibility of redox behavior in the aqueous solution are better than in the organic electrolyte solutions, suggesting that the aqueous solution is favorable for high rate capability. The charge transfer resistance, the exchange current and the capacitance of the double layer vary with the charge voltage during the deintercalation process. At the peak of the oxidation (0.87 V), the charge transfer resistance is the lowest. These fundamental results provide a good base for exploring new safe power sources for large scale energy storage.     

High-rate characteristics of novel anode Li4Ti5O12/polyacene materials for Li-ion secondary batteries

In recent years, spinel lithium titanate (Li₄Ti₅O₁₂) as a superior anode material for energy storage battery has attracted a great deal of attention because of the excellent Li-ion insertion and extraction reversibility. However, the high-rate characteristics of this material should be improved if it is used as an active material in large batteries. One effective way to achieve this is to prepare electrode materials coated with carbon. A Li₄Ti₅O₁₂/polyacene (PAS) composite were first prepared via an in situ carbonization of phenol-formaldehyde (PF) resin route to form carbon-based composite. The SEM showed that the Li₄Ti₅O₁₂ particles in the composite were more rounded and smaller than the pristine one. The PAS was uniformly dispersed between the Li₄Ti₅O₁₂ particles, which improved the electrical contact between the corresponding Li₄Ti₅O₁₂ particles, and hence the electronic conductivity of composite material. The electronic conductivity of Li₄Ti₅O₁₂/PAS composite is 10⁻¹ S cm⁻¹, which is much higher than 10⁻⁹ S cm⁻¹ of the pristine Li₄Ti₅O₁₂. High specific capacity, especially better high-rate performance was achieved with this Li₄Ti₅O₁₂/PAS electrode material. The initial specific capacity of the sample is 144 mAh/g at 3 C, and it is still 126.2 mAh/g after 200 cycles. By increasing the current density, the sample still maintains excellent cycle performance.     

Mechanism transition of cell-impedance-controlled lithium transport through Li1−δMn2O4 composite electrode caused by surface-modification and temperature variation

The mechanism transition of lithium transport through a Li_1−δMn₂O₄ composite electrode caused by the surface-modification and temperature variation was investigated using the galvanostatic intermittent titration technique (GITT), electrochemical impedance spectroscopy (EIS) and the potentiostatic current transient technique. From the analyses of the ac-impedance spectra, experimentally measured from unmodified Li_1−δMn₂O₄ and surface-modified Li_1−δMn₂O₄ with MgO composite electrodes, the internal cell resistance of the MgO-modified Li_1−δMn₂O₄ electrode was determined to be much smaller in value than that of the unmodified electrode over the whole potential range. Moreover, from the analysis of the anodic current transients measured on the MgO-modified Li_1−δMn₂O₄ electrode, it was found that the cell-impedance-controlled constraint at the electrode surface is changed to a diffusion-controlled constraint, which is characterised by a large potential step and simultaneously by a small amount of lithium transferred during lithium transport. This strongly suggests that the internal cell resistance plays a significant role in determining the cell-impedance-controlled lithium transport through the MgO-modified Li_1−δMn₂O₄ electrode. Furthermore, from the temperature dependence of the internal cell resistance and diffusion resistance in the unmodified Li_1−δMn₂O₄ composite electrode measured by GITT and EIS, it was concluded that which mechanism of lithium transport will be operative strongly depends on the diffusion resistance as well as on the internal cell resistance.     

Properties of Li-graphite and LiFePO4 electrodes in LiPF6–sulfolane electrolyte

Sulfolane (also referred to as tetramethylene sulfone, TMS) containing LiPF₆ and vinylene carbonate (VC) was tested as a non-flammable electrolyte for a graphite |LiFePO₄ lithium-ion battery. Charging/discharging capacity of the LiFePO₄ electrode was ca. 150 mAh g⁻¹ (VC content 5 wt%). The capacity of the graphite electrode after 10 cycles establishes at the level of ca. 350 mAh g⁻¹ (C/10 rate). In the case of the full graphite |1 M LiPF₆ + TMS + VC 10 wt% |LiFePO₄ cell, both charging and discharging capacity (referred to cathode mass) stabilized at a value of ca. 120 mAh g⁻¹. Exchange current density for Li⁺ reduction on metallic lithium, estimated from electrochemical impedance spectroscopy (EIS) experiments, was j_o(Li/Li⁺) = 8.15 × 10⁻⁴ A cm⁻². Moreover, EIS suggests formation of the solid electrolyte interface (SEI) on lithium, lithiated graphite and LiFePO₄ electrodes, protecting them from further corrosion in contact with the liquid electrolyte. Scanning electron microscopy (SEM) images of pristine electrodes and those taken after electrochemical cycling showed changes which may be interpreted as a result of SEI formation. No graphite exfoliation was observed. The main decomposition peak of the LiPF₆ + TMS + VC electrolyte (TG/DTA experiment) was present at ca. 275 °C. The LiFePO₄(solid) + 1 M LiPF₆ + TMS + 10 wt% VC system shows a flash point of ca. 150 °C. This was much higher in comparison to that characteristic of a classical LiFePO₄ (solid) + 1 M LiPF₆ + 50 wt% EC + 50 wt% DMC system (T_f ≈ 37 °C).