Electrochemical corrosion behaviour of plasma electrolytic oxidation coatings on AM50 magnesium alloy formed in silicate and phosphate based electrolytes

PEO coatings were produced on AM50 magnesium alloy by plasma electrolytic oxidation process in silicate and phosphate based electrolytes using a pulsed DC power source. The microstructure and composition of the PEO coatings were analyzed by scanning electron microscopy (SEM) and X-ray Diffraction (XRD). The corrosion resistance of the PEO coatings was evaluated using open circuit potential (OCP) measurements, potentiodynamic polarisation tests and electrochemical impedance spectroscopy (EIS) in 0.1 M NaCl solution. It was found that the electrolyte composition has a significant effect on the coating evolution and on the resulting coating characteristics, such as microstructure, composition, coating thickness, roughness and thus on the corrosion behaviour. The corrosion resistance of the PEO coating formed in silicate electrolyte was found to be superior to that formed in phosphate electrolyte in both the short-term and long-term electrochemical corrosion tests.     

Poly(N-ethylaniline) coatings on 304 stainless steel for corrosion protection in aqueous HCl and NaCl solutions

Poly(N-ethylaniline) (PNEA) coatings were grown by potentiodynamic synthesis technique on 304 stainless steel (SS) alloy from 0.1 M of N-ethylaniline (NEA) in 0.3 M oxalic acid solution. Characterization of adhesive and electroactive PNEA coatings was carried out by cyclic voltammetry, FT-IR spectroscopy and scanning electron microscopy (SEM) techniques. The protective properties of PNEA coatings on SS were elucidated using linear anodic potentiodynamic polarization, Tafel and electrochemical impedance spectroscopy (EIS) test techniques, in highly aggressive 0.5 M HCl and 0.5 M NaCl solutions. Linear anodic potentiodynamic polarization test results proved that PNEA coating improved the degree of protection against pitting corrosion in HCl and NaCl solutions. Tafel test results showed that PNEA coating appears to enhancement protection for SS in 0.5 M NaCl and 0.5 M HCl solutions. However, according to long-term EIS results, PNEA coating is better for the protection of SS electrodes during the long immersion period in NaCl compared to that in HCl medium.     

Effect of electrolyte additives on performance of plasma electrolytic oxidation films formed on magnesium alloy AZ91D

Various plasma electrolytic oxidation (PEO) films were prepared on magnesium alloy AZ91D in a silicate bath with different additives such as phosphate, fluoride and borate. Effects of the additives on chemical composition and corrosion resistance of the PEO films were examined by means of scanning electron microscopy (SEM), potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in 3.5% NaCl solution. The results showed that the PEO films obtained in solutions with both borate and fluoride had better corrosion resistance. In order to understand the corrosion mechanism of PEO films on magnesium alloy AZ91D, electronic property of the magnesium electrode with PEO films was studied by Mott-Schottky approach in a solution containing borate and chloride. The results indicated that magnesium electrodes with and without PEO films all exhibited n-type semiconducting property. However, in comparison with the magnesium electrode treated in solutions containing phosphate or borate, the electrode treated in solutions containing both borate and fluoride (M-film) had lower donor concentration and much negative flat band potential; therefore, the M-film had lower reactivity and higher corrosion resistance.     

High corrosion protection of a polyaniline/organophilic montmorillonite coating for magnesium alloys

Epoxy coatings containing polyaniline (PANI) and polyaniline/organophilic montmorillonite (PANI/OMMT) powders were prepared on the surface of AZ91D magnesium alloy. The corrosion performance of the coatings was evaluated by electrochemical impedance spectroscopy (EIS) and open-circuit potential analysis in 3.5% NaCl. The results indicate that the PANI/OMMT coating retained its high corrosion protection for AZ91D magnesium alloy after 6000 h of immersion. The protective mechanism conferred by the PANI/OMMT coating was also discussed. The effects of oxygen on the protective mechanism of PANI were evaluated by EIS measurements in a 3.5% deaerated NaCl solution.     

Smart self-healing anti-corrosion vanadia coating for magnesium alloys

Eco-friendly vanadia based chemical conversion coating was applied for improving the corrosion resistance of a newly developed magnesium AZ31 HP-O alloy. The effect of vanadia solution concentrations (10, 30 and 50 g/l) and pH (neutral pH 7 and pH 9) on the corrosion protection performance of a magnesium substrate were investigated. EIS and linear polarization techniques were used to evaluate the electrochemical behavior in 3.5% NaCl. The results showed a marked increase in the localized corrosion resistance after applying vanadia surface treatment of 50 g/l due to self-healing effect. The optimum conditions to obtain protective coatings for AZ31 HP-O with a self-healing ability were determined. Changes in surface morphology, composition and microstructure of the conversion coatings were followed by SEM-EDS and macroscopic imaging techniques.     

Effect of Ni content on the corrosion behavior of Cu-Ni alloys in neutral chloride solutions

The effect of systematic increase of Ni content on the electrochemical behavior of the Cu-Ni alloys in neutral chloride solutions was investigated. The pitting corrosion behavior of Cu-Ni alloys with different Ni contents, namely, 5, 10, 30 and 65 mass% Ni, in a stagnant 0.6 mol dm⁻³ NaCl solution of pH 7.0 was studied. The effect of chloride ion concentration on the electrochemical behavior of these alloys was also investigated. The results show that the increase in nickel content decreases the corrosion rate of the alloys in the neutral chloride solution. The increase of chloride concentration up to 0.3 mol dm⁻³ increases the corrosion rate. At higher concentrations ([Cl⁻] > 0.3 mol dm⁻³) the corrosion rate decreases due to the hydrolysis of Cu(I) chloride to form the passive Cu(I) oxide film. The breakdown potential depends on the chloride ion concentration and the nickel content of the alloy. For these investigations conventional electrochemical techniques and electrochemical impedance spectroscopy (EIS) were used. The impedance measurements have shown that the increase of the Ni content and the immersion time of the alloys in the chloride solution increase the corrosion resistance of the alloys. The experimental impedance data were fitted to theoretical values according to a proposed equivalent circuit model.     

Study on the corrosion behavior of reinforcing steel in simulated concrete pore solutions using in situ Raman spectroscopy assisted by electrochemical techniques

In situ Raman spectroscopy, electrochemical impedance spectroscopy (EIS) and polarization curves were used to study the corrosion behavior of reinforcing steel in simulated concrete pore (SCP) solutions (saturated Ca(OH)₂ solutions). Results indicated that the reinforcing steel remained passive in chloride-free SCP solutions. However, the anodic polarization curve of the steel did not exhibit a stable passive region in the SCP solution with 0.5 M NaCl, the corrosion current density exceeded 0.1 μA cm⁻², the steel surface was unstable with chloride attack and localized corrosion appeared on it with FeCO₃ and Fe₂O₃ as the main corrosion products.     

Corrosion resistance of plasma-anodized AZ91D magnesium alloy by electrochemical methods

Anodic coatings formed on magnesium alloys by plasma anodization process are mainly used as protective coatings against corrosion. The effects of KOH concentration, anodization time and current density on properties of anodic layers formed on AZ91D magnesium alloy were investigated to obtain coatings with improved corrosion behaviour. The coatings were characterized by scanning electron microscopy (SEM), electron dispersion X-ray spectroscopy (EDX), X-ray diffraction (XRD) and micro-Raman spectroscopy. The film is porous and cracked, mainly composed of magnesium oxide (MgO), but contains all the elements present in the electrolyte and alloy. The corrosion behaviour of anodized Mg alloy was examined by using stationary and dynamic electrochemical techniques in corrosive water. The best corrosion resistance measured by electrochemical methods is obtained in the more concentrated electrolyte 3 M KOH + 0.5 M KF + 0.25 M Na₃PO₄·12 H₂O, with a long anodization time and a low current density. A double electrochemical effects of the anodized layer on the magnesium corrosion is observed: a large inhibition of the cathodic process and a stabilization of a large passivation plateau.     

Electrochemical corrosion behavior of composite coatings of sealed MAO film on magnesium alloy AZ91D

Protective composite coatings were prepared on magnesium alloy AZ91D by micro-arc oxidation (MAO) treatment plus a top coating with sealing agent using multi-immersion technique under low-pressure conditions. The corrosion resistance of AZ91D alloy with composite coatings was superior evidently to that with merely MAO film. SEM observations revealed that the sealing agent was integrated with MAO film by physically interlocking; therewith covered uniformly the surface as well as penetrated into pores and micro-cracks of MAO film. The anti-corrosion properties in 3.5% NaCl solution of the composite coatings were evaluated by using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements. Based on the results of chronopotentiometric (E ∼ t) and EIS measurements for long time immersion in 3.5% NaCl solution, appropriate equivalent circuits for the composite coatings system were proposed. It follows that due to the blocking effect of the sealing agent in pores and cracks in MAO film, the composite coatings can suppress the corrosion process by holding back the transfer or diffusion of electrolyte and corrosion products between the composite coatings and solution during immersion.     

The effect of potential bias on the formation of ionic liquid generated surface films on Mg alloys

An electrochemical approach to the formation of a protective surface film on Mg alloys immersed in the ionic liquid (IL), trihexyl(tetradecyl)phosphonium-bis 2,4,4-trimethylpentylphosphinate, was investigated in this work. Initially, cyclic voltammetry was used with the Mg alloy being cycled from OCP to more anodic potentials. EIS data indicate that, under these circumstances, an optimum level of protection was achieved at intermediate potentials (e.g., 0 or 0.25 V versus Ag/AgCl). In the second part of this paper, a small constant bias was applied to the Mg alloy immersed in the IL for extended periods using a novel cell design. This electrochemical cell allowed us to monitor in situ surface film formation on the metal surface as well as the subsequent corrosion behaviour of the metal in a corrosive medium. This apparatus was used to investigate the evolution of the surface film on an AZ31 magnesium alloy under a potential bias (between ±100 mV versus open circuit) applied for over 24 h, and the film evolution was monitored using electrochemical impedance spectroscopy (EIS). A film resistance was determined from the EIS data and it was shown that this increased substantially during the first few hours (independent of the bias potential used) with a subsequent decrease upon longer exposure of the surface to the IL. Preliminary characterization of the film formed on the Mg alloy surface using ToF-SIMS indicates that a multilayer surface exists with a phosphorous rich outer layer and a native oxide/hydroxide film underlying this. The corrosion performance of a treated AZ31 specimen when exposed to 0.1 M NaCl aqueous solution showed considerable improvement, consistent with electrochemical data.     

Preparation and corrosion resistance studies of nanometric sol-gel-based CeO2 film with a chromium-free pretreatment on AZ91D magnesium alloy

Magnesium alloy, although valuable, is reactive and requires protection before it can be applied in many fields. In this study, a novel protective environmental-friendly gradient coating was performed on AZ91D magnesium alloy by non-chromate surface treatments, which consisted of phytic acid chemical conversion coating and the sol-gel-based CeO₂ thin film. The surface morphologies, microstructure and composition of the coatings were investigated by scanning electron microscopy (SEM), energy disperse spectroscopy (EDS) and X-ray diffraction (XRD), respectively. The corrosion resistance of the coatings was evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in 3.5 wt.% NaCl solution. The effects of the concentration, layers, temperature of heat treatment of CeO₂ sol on the anti-corrosion properties of the gradient coating for magnesium were also investigated. The results showed that the gradient coating was mainly composed of crystalline CeO₂. According to the results of electrochemical tests, the corrosion resistance of AZ91D magnesium alloy was found to be greatly improved by means of this new environmental-friendly surface treatment.     

Effects of 1,4-naphthoquinone on aluminum corrosion in 0.50 M sodium chloride solutions

Effects of 1,4-naphthoquinone (NQ) have been investigated as a corrosion inhibitor for aluminum in aerated and de-aerated solutions of 0.50 M NaCl using potentiodynamic polarization, chronoamperometry (CA), open-circuit potential (OCP), electrochemical impedance spectroscopic (EIS), scanning electron microscopic (SEM), cyclic voltammetric, and quartz crystal analyzer (QCA) techniques. These measurements revealed that the presence of NQ shifted the corrosion and pitting potentials to more noble values and decreased the anodic currents in the passive region in both aerated and de-aerated chloride solutions, and the surface and polarization resistances are increased as the concentration of NQ is increased. The most effective concentration of NQ for corrosion inhibition was found to be 1.0 × 10⁻³ M in both aerated and de-aerated chloride solutions. The QCA data indicate that adsorption of NQ molecules plays an important role in protecting the pits on the aluminum surface. The SEM images show that the presence of NQ decreased the severity of the pitting corrosion of aluminum to a great extent at −675 mV versus Ag/AgCl.     

A novel approach to heal the sol-gel coating system on magnesium alloy for corrosion protection

Sol-gel-based coatings exhibit high potentiality to be as an alternative to toxic chromate coatings for surface pre-treatment of metals and alloys. However, as soon as even small defects appear in the coating, the coating cannot stop the development of corrosion process. Present work demonstrates the possibility to use zinc nitrate as healing agent to repair the organic silane coatings in NaCl solution. The zinc nitrate was added to the 0.005 M NaCl solution where AZ91D magnesium alloy coated with organic silane coating was immersed. The healing process and the healing mechanism were investigated by electrochemical measurements and scanning electron microcopy coupled with energy dispersive spectroscopy. The results demonstrated the introduction of zinc nitrate to the electrolyte could stop the development of corrosion process of the coating system and a remarkable recovery on corrosion resistance could be obtained. This effect may be attributed to the formation of zinc oxide/hydroxide on the defective areas, hindering the corrosion activities.     

Novel hybrid sol-gel coatings for corrosion protection of AZ31B magnesium alloy

This work aims to develop and study new anticorrosion films for AZ31B magnesium alloy based on the sol-gel coating approach.Hybrid organic-inorganic sols were synthesized by copolymerization of epoxy-siloxane and titanium or zirconium alkoxides. Tris(trimethylsilyl) phosphate was also used as additive to confer additional corrosion protection to magnesium-based alloy. A sol-gel coating, about 5-μm thick, shows good adhesion to the metal substrate and prevents corrosion attack in 0.005 M NaCl solution for 2 weeks. The sol-gel coating system doped with tris(trimethylsilyl)-phosphate revealed improved corrosion protection of the magnesium alloy due to formation of hydrolytically stable Mg-O-P chemical bonds.The structure and the thickness of the sol-gel film were characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The corrosion behaviour of AZ31B substrates pre-treated with the sol-gel derived hybrid coatings was tested by electrochemical impedance spectroscopy (EIS). The chemical composition of the silylphosphate-containing sol-gel film at different depths was investigated by X-ray photoelectron spectroscopy (XPS) with depth profiling.     

Improved electrochemical performance of trivalent-chrome coating on Al 6063 alloy via urea and thiourea addition

This project aims at improving the electrochemical performance of trivalent-chrome coating through urea and thiourea addition. The electrochemical behaviors of coatings formed with different concentrations of urea and thiourea were investigated in 3.5 wt.% NaCl solution at 25 °C, using potentiodynamic polarization curves and EIS. The corrosion resistance of coatings is improved greatly by adding a small amount of inhibitors, whereas the excessive addition deteriorates the corrosion resistance. Thiourea addition presents better effect than urea. To explain the EIS results of the coatings, a simple equivalent circuit was designed. The EIS parameters were obtained by fitting the EIS plots. The results of the polarization curves and EIS show that the inhibitor-containing coatings present better corrosion resistance than the coating without inhibitor. The morphology and composition and valence state of the conversion coatings were examined by SEM and EDS and XPS, respectively. The results indicated that the trivalent chromium coating was developed on Al 6063 alloy, urea and thiourea inhibitors were also deposited on the substrates, respectively. A noticeable chemical shift was also observed.     

Assessment of a one-step intelligent self-healing vanadia protective coatings for magnesium alloys in corrosive media

Eco-friendly vanadia based chemical conversion coating was applied for improving the corrosion resistance of a newly developed magnesium AZ31 HP-O alloy. The effect of vanadia solution concentrations (10, 30 and 50 g/l) and pH on the corrosion protection performance of magnesium substrate were investigated. EIS and cyclic voltammetry techniques were used to evaluate the electrochemical behavior in 3.5% NaCl. Results showed a marked increase in the localized corrosion resistance after applying vanadia surface treatment of 50 g/l as measured by EIS and polarization techniques. The optimum conditions to obtain protective coatings for AZ31 HP-O were determined. The surface morphology, composition and microstructure of conversion coatings were followed by AFM, SEM-EDS and macroscopic imaging techniques.     

Electrochemical impedance spectroscopic investigation of the role of alkaline pre-treatment in corrosion resistance of a silane coating on magnesium alloy, ZE41

The protective performance of the coatings of bis-1,2-(triethoxysilyl) ethane (BTSE) on ZE41 magnesium alloy with different surface pre-treatments were evaluated using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in 0.1 M sodium chloride solution. Electrical equivalent circuits were developed based upon hypothetical corrosion mechanisms and simulated to correspond to the experimental data. The morphology and cross section of the alloy subjected to different pre-treatments and coatings were characterized using scanning electron microscope. A specific alkaline pre-treatment of the substrate prior to the coating has been found to improve the corrosion resistance of the alloy.     

Electrodeposited Ni-B alloy coatings: Structure, corrosion resistance and mechanical properties

Ni-B alloy coatings with different boron content ranging from 4 to approximately 28 at.% were prepared by electrodeposition in a nickel-plating bath containing sodium decahydroclovodecaborate as a boron source. The influence of the boron concentration in the coatings on their structure, morphology, electrochemical and corrosion behavior, physico-mechanical and electrical properties was investigated using X-ray diffractometry (XRD), scanning electron microscopy (SEM), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and other methods. It was found that the electrodeposited Ni-B coatings with relatively low boron content (≤8 at.%) are nanocrystalline and comprise a solid solution of boron in f.c.c. Ni lattice having a mixed substituted-interstitial type. Further increase in the boron content (up to 10-15 at.%) leads to the appearance of heterogeneous amorphous-nanocrystalline structure, and the coatings with a high boron content (20 at.% and above) are X-ray amorphous. Polarization measurements in neutral NaCl solutions showed that the Ni-B coatings with relatively low boron content demonstrate a potential region of low anodic currents associated with the passive film formation at the alloy surface. The anodic current in this potential region increases significantly with increasing the boron content above 10 at.%, suggesting the non-protective nature of the anodic film formed on the amorphous Ni-B alloys. Immersion tests monitored by EIS measurements revealed a significantly better corrosion performance of the Ni-B coatings with low boron content (4 at.%) in comparison with that of the amorphous coatings. The microhardness and wear resistance of the Ni-B coatings essentially increases with increasing the boron content. Maximum microhardness and wear resistance were found for the coatings containing 8 at.% B.     

Corrosion inhibition of steel using mesoporous silica nanocontainers incorporated in the polypyrrole

Mesoporous silica nanocontainer powders were applied as corrosion inhibitor hosts. These powders were dispersed in the polypyrrole matrix by electropolymerization technique. The protection properties of these composite coatings with and without inhibitor were studied in 2 g dm⁻³ chloride ion solutions at constant pH. Open circuit potential (OCP), inductive coupled plasma (ICP), X-ray diffraction (XRD), electrochemical impedance spectroscopy (EIS), and Fourier transform infrared spectroscopy (FTIR) results showed that the substrates were protected due to the release of corrosion inhibitor from mesoporous silica in the chloride media compared to the coatings without corrosion inhibitor. The released corrosion inhibitor reacted with substrate and made a protective phase during corrosion. This phase can heal the corroded area as a self-healing compound.     

Influence of substrate composition on corrosion protection of sol–gel thin films on magnesium alloys in 0.6 M NaCl aqueous solution

The corrosion protection behaviour of organic–inorganic hybrid thin films on AZ31 and AZ61 magnesium alloy substrates has been studied. These films were prepared by a sol–gel dip-coating method. The organopolysiloxane precursors were γ-methacryloxypropyltrimethoxysilane (MAPTMS) and tetramethoxysilane (TMOS). An attempt was made to determine the possible relationships between the degradation of the sol–gel film and composition of the metal substrate during the exposure of the metal/coating system to 0.6 M NaCl aqueous solutions. For this purpose electrochemical impedance spectroscopy (EIS) and hydrogen evolution measurements were applied. Scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) analyses revealed that the sol–gel films formed on the surface of AZ61 alloy were far more perfect and uniform than those formed on the AZ31 alloy. This behaviour was attributed to the effect of the native oxide film initially present on the surface of the AZ61 alloy, which inhibited the attack of magnesium. Results indicated that the sol–gel coated AZ61 substrate tended to develop corrosion products slower than the sol–gel coated AZ31 substrate, trend that could change by prolonging exposure time. After 6 days of immersion, a clear inhibitive effect of the corrosion products formed during the test was observed in the case of the sol–gel coated AZ31, but not with the coated AZ61 alloy substrate, a phenomenon explained by the carbonate enrichment observed by XPS.