Gold nanoparticles mediate the assembly of manganese dioxide nanoparticles for H2O2 amperometric sensing

Aggregates of gold nanoparticles (AuNPs) that mediate the assembly of manganese dioxide nanoparticles (nano-MnO₂) for hydrogen peroxide (H₂O₂) amperometric sensing have been developed. The aggregates were prepared by directly mixing citric-capped AuNPs and poly(allylamine hydrochloride) (PAH)-capped nano-MnO₂ using an electrostatic self-assembly strategy. The prepared sensor exhibited excellent electrochemical behaviors and a wide linear range from 7.80 × 10⁻⁷ to 8.36 × 10⁻⁴ M with a detection limit of 4.68 × 10⁻⁸ M (S/N = 3) because of the synergistic influence of excellent catalytic ability of MnO₂ and good electrical conductivity of AuNPs. In addition, its applicability to practical samples for measuring H₂O₂ in toothpastes has obtained a satisfactory result. Due to the ease of preparation and excellent properties of the sensor, indicating the MnO₂-AuNP material may be a potential H₂O₂ sensor.     

A hydrogen peroxide sensor based on a horseradish peroxidase/polyaniline/carboxy-functionalized multiwalled carbon nanotube modified gold electrode

We have developed a polyaniline/carboxy-functionalized multiwalled carbon nanotube (PAn/MWCNTCOOH) nanocomposite by blending the emeraldine base form of polyaniline (PAn) and carboxy-functionalized multiwalled carbon nanotubes (MWCNT) in dried dimethyl sulfoxide (DMSO) at room temperature. The conductivity of the resulting PAn/MWCNTCOOH was 3.6 × 10⁻³ S cm⁻¹, mainly as a result of the protonation of the PAn with the carboxyl group and the radical cations of the MWCNT fragments. Horseradish peroxidase (HRP) was immobilized within the PAn/MWCNTCOOH nanocomposite modified Au (PAn/MWCNTCOOH/Au) electrode to form HRP/PAn/MWCNTCOOH/Au for use as a hydrogen peroxide (H₂O₂) sensor. The adsorption between the negatively charged PAn/MWCNTCOOH nanocomposite and the positively charged HRP resulted in a very good sensitivity to H₂O₂ and an increased electrochemically catalytical current during cyclic voltammetry. The HRP/PAn/MWCNTCOOH/Au electrode exhibited a broad linear response range for H₂O₂ concentrations (86 μM–10 mM). This sensor exhibited good sensitivity (194.9 μA mM⁻¹ cm⁻²), a fast response time (2.9 s), and good reproducibility and stability at an applied potential of −0.35 V. The construction of the enzymatic sensor demonstrated the potential application of PAn/MWCNTCOOH nanocomposites for the detection of H₂O₂ with high performance and excellent stability.     

A novel hydrogen peroxide biosensor based on Au-graphene-HRP-chitosan biocomposites

Graphene was prepared successfully by introducing -SO₃⁻ to separate the individual sheets. TEM, EDS and Raman spectroscopy were utilized to characterize the morphology and composition of graphene oxide and graphene. To construct the H₂O₂ biosensor, graphene and horseradish peroxidase (HRP) were co-immobilized into biocompatible polymer chitosan (CS), then a glassy carbon electrode (GCE) was modified by the biocomposite, followed by electrodeposition of Au nanoparticles on the surface to fabricate Au/graphene/HRP/CS/GCE. Cyclic voltammetry demonstrated that the direct electron transfer of HRP was realized, and the biosensor had an excellent performance in terms of electrocatalytic reduction towards H₂O₂. The biosensor showed high sensitivity and fast response upon the addition of H₂O₂, under the conditions of pH 6.5, potential −0.3 V. The time to reach the stable-state current was less than 3 s, and the linear range to H₂O₂ was from 5 × 10⁻⁶ M to 5.13 × 10⁻³ M with a detection limit of 1.7 × 10⁻⁶ M (S/N = 3). Moreover, the biosensor exhibited good reproducibility and long-term stability.     

Li diffusion in LiNi0.5Mn0.5O2 thin film electrodes prepared by pulsed laser deposition

Kinetic and transport parameters of Li ion during its extraction/insertion into thin film LiNi_0.5Mn_0.5O₂ free of binder and conductive additive were provided in this work. LiNi_0.5Mn_0.5O₂ thin film electrodes were grown on Au substrates by pulsed laser deposition (PLD) and post-annealed. The annealed films exhibit a pure layered phase with a high degree of crystallinity. Surface morphology and thin film thickness were investigated by field emission scanning electron microscopy (FESEM). The charge/discharge behavior and rate capability of the thin film electrodes were investigated on Li/LiNi_0.5Mn_0.5O₂ cells at different current densities. The kinetics of Li diffusion in these thin film electrodes were investigated by cyclic voltammetry (CV) and galvanostatic intermittent titration technique (GITT). CV was measured between 2.5 and 4.5 V at different scan rates from 0.1 to 2 mV/s. The apparent chemical diffusion coefficients of Li in the thin film electrode were calculated to be 3.13 × 10⁻¹³ cm²/s for Li intercalation and 7.44 × 10⁻¹⁴ cm²/s for Li deintercalation. The chemical diffusion coefficients of Li in the thin film electrode were determined to be in the range of 10⁻¹²-10⁻¹⁶ cm²/s at different cell potentials by GITT. It is found that the Li diffusivity is highly dependent on the cell potential.     

Direct electron-transfer and electrochemical catalysis of hemoglobin immobilized on mesoporous Al2O3

The direct electrochemistry of hemoglobin (Hb) has been achieved by immobilizing Hb on mesoporous Al₂O₃ (meso-Al₂O₃) film modified glassy carbon (GC) electrode. Meso-Al₂O₃ shows significant promotion to the direct electron-transfer of Hb, thus it exhibits a pair of well defined and quasi-reversible peaks with a formal potential of −0.345 V (vs. SCE). The electron-transfer rate constant (k_s) is estimated to be 3.17 s⁻¹. The immobilized Hb retains its biological activity well and shows high catalytic activity to the reduction of hydrogen peroxide (H₂O₂) and nitrite (NO₂⁻). Under the optimized experimental conditions, the catalytic currents are linear to the concentrations of H₂O₂ and NO₂⁻ in the ranges of 0.195-20.5 μM and 0.2-10 mM, respectively. The corresponding detection limits are 1.95 × 10⁻⁸ M and 3 × 10⁻⁵ M (S/N = 3). The resulting protein electrode has high thermal stability and good reproducibility due to the protection effect of meso-Al₂O₃. Ultraviolet visible (UV-vis) absorption spectra and reflection-absorption infrared (RAIR) spectra display that Hb keeps almost natural structure in the meso-Al₂O₃ film. The N₂ adsorption-desorption experiments show that the pore size of meso-Al₂O₃ is about 14.4 nm, suiting for the encapsulation of Hb (average size: 5.5 nm) well. Therefore, meso-Al₂O₃ is an alternative matrix for protein immobilization and biosensor preparation.     

Fabrication of graphene/prussian blue composite nanosheets and their electrocatalytic reduction of H2O2

In this work, graphene/prussian blue (PB) composite nanosheets with good dispersibility in aqueous solutions have been synthesized by mixing ferric-(III) chloride and potassium ferricyanide in the presence of graphene under ambient conditions. Transmission electron microscopy (TEM) shows that the average size of the as-synthesized PB nanoparticles on the surface of graphene nanosheets is about 20 nm. Fourier-transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) patterns have been used to characterize the chemical composition of the obtained graphene/PB composite nanosheets. The graphene/PB composite nanosheets exhibit good electrocatalytic behavior to detection of H₂O₂ at an applied potential of −0.05 V. The sensor shows a good linear dependence on H₂O₂ concentration in the range of 0.02-0.2 mM with a sensitivity of 196.6 μA mM⁻¹ cm⁻². The detection limit is 1.9 μM at the signal-to-noise ratio of 3. Furthermore, the graphene/PB modified electrode exhibits freedom of interference from other co-existing electroactive species. This work provides a new kind of composite modified electrode for amperometric biosensors.     

Fabrication of carbon paste electrode containing [PFeW11O39] polyoxoanion supported on modified amorphous silica gel and its electrocatalytic activity for H2O2 reduction

[PFeW₁₁O₃₉]⁴⁻ (PFeW₁₁) supported on the surface of 3-aminopropyl(triethoxy)silane modified silica gel was synthesized and used as a bulk modifier to fabricate a renewable three-dimensional chemically modified electrode. The electrochemical behavior of the modified electrode was investigated. Cyclic voltammetry studies showed that the PFeW₁₁ on the electrode surface sustained the same electrochemical properties as that of the PFeW₁₁ in solution. The preparation of chemically modified electrode is simple and quiet reproducible using inexpensive material. The modified electrode had high electrocatalytic activity toward H₂O₂ reduction and it was successfully applied as an electrochemical detector to monitor H₂O₂ in flow injection analysis (FIA). The electrocatalytic peak current was found to be linear with the H₂O₂ concentration in the range 10-200 μmol L⁻¹ with a correlation coefficient of 0.998 and a detection limit (3σ) of 7.4 μmol L⁻¹ H₂O₂. The electrode has the remarkable advantage of surface renewal owing to bulk modification, as well as simple preparation, good mechanical and chemical stability and reproducibility.     

Synthesis of spinel LiMn2O4 with manganese carbonate prepared by micro-emulsion method

Micro-spherical particle of MnCO₃ has been successfully synthesized in CTAB-C₈H₁₈-C₄H₉OH-H₂O micro-emulsion system. Mn₂O₃ decomposed from the MnCO₃ is mixed with Li₂CO₃ and sintered at 800 °C for 12 h, and the pure spinel LiMn₂O₄ in sub-micrometer size is obtained. The LiMn₂O₄ has initial discharge specific capacity of 124 mAh g⁻¹ at discharge current of 120 mA g⁻¹ between 3 and 4.2 V, and retains 118 mAh g⁻¹ after 110 cycles. High-rate capability test shows that even at a current density of 16 C, capacity about 103 mAh g⁻¹ is delivered, whose power is 57 times of that at 0.2 C. The capacity loss rate at 55 °C is 0.27% per cycle.     

Synthesis and transport properties in La2−xAxMo2O9−δ (A = Ca, Sr, Ba, K) series

The La_2−xA_xMo₂O_9−δ (A = Ca²⁺, Sr²⁺, Ba²⁺ and K⁺) series has been synthesised as nanocrystalline materials via a modification of the freeze-drying method. The resulting materials have been characterised by X-ray diffraction (XRD), thermal analysis (TG/DTA, DSC), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). The high-temperature β-polymorph is stabilised for dopant content x > 0.01. The nanocrystalline powders were used to obtain dense ceramic materials with optimised microstructure and relative density >95%. The overall conductivity determined by impedance spectroscopy depends on both the ionic radius and dopant content. The conductivity decreases slightly as the dopant content increases in addition a maximum conductivity value was found for Sr²⁺ substitution, which show an ionic radii slightly higher than La³⁺ (e.g. 0.08 S cm⁻¹ for La₂Mo₂O₉ and 0.06 S cm⁻¹ for La_1.9Sr_0.1Mo₂O_9−δ at 973 K). The creation of extrinsic vacancies upon substitution results in a wider stability range under reducing conditions and prevents amorphisation, although the stability is not enhanced significantly when compared to samples with higher tungsten content. These materials present high thermal expansion coefficients in the range of (13-16) × 10⁻⁶ K⁻¹ between room temperature and 753 K and (18-20) × 10⁻⁶ K⁻¹ above 823 K. The ionic transport numbers determined by a modified emf method remain above 0.98 under an oxygen partial pressure gradient of O₂/air and decreases substantially under wet 5% H₂-Ar/air when approaching to the degradation temperature above 973 K due to an increase of the electronic contribution to the overall conductivity.     

Processing and physical properties of Al2O3/aluminum alloy composites

Porous aluminum oxide (Al₂O₃) preforms were formed by sintering in air at 1200 °C for 2 h. A356, 6061, and 1050 aluminum alloys were infiltrated into the preforms by squeeze casting in order to fabricate Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites, respectively, with different volumes of aluminum alloy content. The content of aluminum alloy in the composites was 10–40% by volume. The resistivity of Al₂O₃/A356, Al₂O₃/6061, and Al₂O₃/1050 composites decreased dramatically from 6.41 × 10¹² to 9.77 × 10⁻⁴, 7.28 × 10⁻⁴, and 6.24 × 10⁻⁴ Ω m, respectively, the four-points bending strength increased from 397 to 443, 435.1, 407.2 MPa, respectively, and the deviations were smaller than 2%. From SEM microstructural analysis and TEM bright field images, the pore volume fraction and the relative density of the composites were the most important factors that affected the physical and mechanical properties. The ceramic phase and alloy phase in Al₂O₃/aluminum alloy composites were found to be homogenized and uniformly distributed using electrical and mechanical properties analysis, microstructure analysis, and image analysis.     

Synthesis, microstructure, and photocatalysis of In2O3 hollow particles

Indium oxide (In₂O₃) microspheres with hollow interiors have been prepared by a facile implantation route which enables indium ions released from indium-chloride precursors to implant into nonporous polymeric templates in C₂Cl₄ solvent. The templates are then removed upon calcination at 500 °C in air atmosphere, forming hollow In₂O₃ particles. Specific surface area (0.5-260 m² g⁻¹) and differential pore volume (7 × 10⁻⁹ to 3.8 × 10⁻⁴ m³ g⁻¹ Å⁻¹) of the hollow particles can be tailored by adjusting the precursor concentration. For the hollow In₂O₃ particles with high surface area (260 m² g⁻¹), an enhanced photocatalytic efficiency (up to ∼one-fold increase) against methylene blue (MB) dye is obtained under UV exposure for the aqueous In₂O₃ colloids with a dilute solids concentration of 0.02 wt.%.     

Electrochemical behavior and its electrocatalytic properties of chemically modified electrode with Keggin-type [SiNi(H2O)W11O39]

A monolayer of Keggin-type heteropolyanion [SiNi(H₂O)W₁₁O₃₉]⁶⁻ was fabricated by electrodepositing [SiNi(H₂O)W₁₁O₃₉]⁶⁻ on cysteamine modified gold electrode. The monolayer of [SiNi(H₂O)W₁₁O₃₉]⁶⁻ modified gold electrode was characterized by atomic force microscopy (AFM) and electrochemical method. AFM results showed the [SiNi(H₂O)W₁₁O₃₉]⁶⁻ uniformly deposited on the electrode surface and formed a porous monolayer. Cyclic voltammetry exhibited one oxidation peak and two reduction peaks in 1.0 M H₂SO₄ in the potential range of −0.2 to 0.7 V. The constructed electrode could exist in a large pH (0-7.6) range and showed good catalytic activity towards the reduction of bromate anion (BrO₃⁻) and nitrite (NO₂⁻), and oxidation of ascorbic acid (AA) in acidic solution. The well catalytic active of the electrode was ascribed to the porous structure of the [SiNi(H₂O)W₁₁O₃₉]6⁻ monolayer.     

Nanocomposite Fe2O3-Se as a new lithium storage material

The electrochemical properties of nanocomposite Fe₂O₃-Se thin film prepared by pulsed laser deposition (PLD) method have been investigated by cyclic voltammetry and charge/discharge measurements. A large reversible capacity of nanocomposite Fe₂O₃-Se thin film was found to be around 650 mAh g⁻¹. A new couple of reduction and oxidation peaks at 1.4 and 1.8 V were observed from cyclic voltammogram for the first time. Our data demonstrated that nanocomposite Fe₂O₃-Se exhibit larger capacity and better cycle performance than pure Fe₂O₃. The electrochemical reaction mechanisms of Fe₂O₃-Se with lithium were examined by X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (HRTEM) and selected-area electron diffraction (SAED). The reversible conversions reaction of nanosized metal Fe with Li₂Se and Li₂O formed after initial discharge process into FeSe and Fe₂O₃ respectively were revealed.     

Preparation and characterization of negative thermal expansion Sc2W3O12/Cu core-shell composite

A composite of Sc₂W₃O₁₂/Cu where Sc₂W₃O₁₂, the core, is coated by the Cu shell was synthesized using simple electroless plating method. As-prepared Sc₂W₃O₁₂/Cu composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS) and thermomechanical analyzer (TMA) techniques. The study results show that the Pd-Sn activator was successfully formed on the surface of Sc₂W₃O₁₂ after the sensitization and activation. In the electroless plating process, Cu nanocrystals formed firstly, and then grew together to form a continuous coating. Sc₂W₃O₁₂/Cu core-shell composites exhibit a negative linear coefficient of thermal expansion CTE = −4.47 × 10⁻⁶ °C⁻¹ from room temperature to 200 °C.     

Evaluation of electrical energy per order (EEO) with kinetic modeling on the removal of Malachite Green by US/UV/H2O2 process

The kinetics of decolorization of Malachite Green (MG) as a model cationic dye from textile industry, by US/UV/H₂O₂ process, was investigated with nonlinear regression analysis. The experimental results indicated that the decolorization kinetics of MG in this process fit well by pseudo-first order kinetics. With nonlinear regression analysis a model was developed for pseudo-first order constant (k_ap) as a function of operational parameters such as initial concentrations of H₂O₂ (25-600 mg l^− 1) and MG (1.82-9.87 mg l^− 1), temperature (294-307 K) and power density (0.049-0.16 W ml^− 1) as following:

     

Inorganic-organic hybrid membranes with anhydrous proton conduction prepared from tetramethoxysilane/methyl-trimethoxysilane/trimethylphosphate and 1-ethyl-3-methylimidazolium-bis (trifluoromethanesulfonyl) imide for H2/O2 fuel cells

Anhydrous proton-conducting inorganic-organic hybrid membranes were prepared by sol-gel process with tetramethoxysilane/methyl-trimethoxysilane/trimethylphosphate and 1-ethyl-3-methylimidazolium-bis (trifluoromethanesulfonyl) imide [EMI][TFSI] ionic liquid as precursors. These hybrid membranes were studied with respect to their structural, thermal, proton conductivity, and hydrogen permeability properties. The Fourier transform infrared spectroscopy (FT-IR) and ³¹P, ¹H, and ¹³C nuclear magnetic resonance (NMR) measurements have shown good chemical stability, and complexation of PO(OCH₃)₃ with [EMI][TFSI] ionic liquid in the studied hybrid membranes. Thermal analysis including TG and DTA confirmed that the membranes were thermally stable up to 330 °C. Thermal stability of the hybrid membranes was significantly enhanced by the presence of inorganic SiO₂ framework and high stability of [TFSI] anion. The effect of [EMI][TFSI] ionic liquid addition on the microstructure of the membranes was studied by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX) micrographs and no phase separation at the surfaces of the prepared membranes was observed and also homogeneous distribution of all elements was confirmed. Proton conductivity of all the prepared membranes was measured from −20 °C to 150 °C, and high conductivity of 5.4 × 10⁻³ S/cm was obtained for 40 wt% [EMI][TFSI] doped 40TMOS-50MTMOS-10PO(OCH₃)₃ (mol%) hybrid membrane, at 150 °C under anhydrous conditions. The hydrogen permeability was found to decrease from 1.61 × 10⁻¹¹ to 1.39 × 10⁻¹² mol/cm s Pa for 40 wt% [EMI][TFSI] doped hybrid membrane as the temperature increases from 20 °C to 150 °C. For 40 wt% [EMI][TFSI] doped hybrid membrane, membrane electrode assemblies were prepared and a maximum power density value of 0.22 mW/cm² at 0.47 mA/cm² as well as a current density of 0.76 mA/cm² were obtained at 150 °C under non-humidified conditions when utilized in a H₂/O₂ fuel cell.     

Direct synthesis of H2O2 acid solutions on carbon cathode prepared from activated carbon and vapor-growing-carbon-fiber by a H2/O2 fuel cell

Direct synthesis of H₂O₂ acid solutions was studied using a gas-diffusion cathode prepared from activated carbon (AC), vapor-growing-carbon-fiber (VGCF) and poly-tetra-fluoro-ethylene (PTFE) powders, with a new H₂/O₂ fuel cell reactor. O₂ reduction to H₂O₂ was remarkably enhanced at the three-phase boundary (O₂(g)-electrode(s)-acid(l)) at the [AC + VGCF] cathode. Fast diffusion processes of O₂ to the active surface and of H₂O₂ to the bulk acid solutions were essential for H₂O₂ accumulation. Synergy of AC and VGCF was observed for the H₂O₂ formation. RRDE and cyclic voltammetry studies indicated that the surface of AC functioned as the active phase for O₂ reduction to HO₂, and VGCF functioned as an electron conductor and a promoter to convert HO₂ to H₂O₂. A maximum H₂O₂ concentration of 353 mM (1.2 wt%) was accomplished under short-circuit conditions (current density 12.7 mA cm⁻², current efficiency 40.1%, geometric area of cathode 1.3 cm², reaction time 6 h).     

Sintering of glass-added BaZn1/3Nb2/3O3 ceramics

The complex perovskite oxide Ba(Zn_1/3Nb_2/3)O₃ (BZN) has been studied for its attractive dielectric properties which place this material interesting for applications as multilayer ceramics capacitors or hyperfrequency resonators. This material is sinterable at low temperature with combined glass phase–lithium salt additions, and exhibits, at 1 MHz very low dielectric losses combined with relatively high dielectric constant and a good stability of this later versus temperature. The 2 wt.% of ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of LiF-added BZN sample sintered at 900 °C exhibits a relative density higher than 95% and attractive dielectric properties: a dielectric constant ?_r of 39, low dielectrics losses (tan(δ) < 10⁻³) and a temperature coefficient of permittivity τ_? of 45 ppm/°C⁻¹. The 2 wt.% ZnO–SiO₂–B₂O₃ glass phase and 1 wt.% of B₂O₃-added BZN sintered at 930 °C exhibits also attractive dielectric properties (?_r = 38, tan(δ) < 10⁻³) and it is more interesting in terms of temperature coefficient of the permittivity (τ_? = −5 ppm/°C). Their good dielectric properties and their compatibility with Ag electrodes, make these ceramics suitable for L.T.C.C applications.     

Iron-enriched natural zeolite modified carbon paste electrode for H2O2 detection

This work demonstrates that iron-enriched natural zeolitic volcanic tuff (Paglisa deposit, Cluj county, Transilvania, Romania) resulting from a previous use as adsorbent in wastewater treatment can be recycled into effective electrode modifier applied to the electrocatalytic detection of hydrogen peroxide. After physico-chemical characterization of tuff samples using various techniques such as chemical analysis, X-ray diffraction, scanning electron microscopy, infrared spectroscopy, BET analysis and X-ray photoelectron spectroscopy, the electrochemical response of the iron-enriched zeolites was studied on the basis of solid carbon paste electrodes modified with these samples. The results indicate that iron centers in the zeolite are electroactive and that they act as electrocatalysts in the voltammetric and amperometric detection of H₂O₂. Best performance was achieved in phosphate buffer at pH 7, showing a sensitivity of 0.57 mA M⁻¹ cm⁻², a detection limit down to 60 μM, and a linear domain up to 100 mM H₂O₂.     

An unusual H2O2 electrochemical sensor based on Ni(OH)2 nanoplates grown on Cu substrate

In this work, Ni(OH)₂ nanoplates grown on the Cu substrate were synthesized and characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Then a novel Cu-Ni(OH)₂ modified glass carbon electrode (Cu-Ni(OH)₂/GCE) was fabricated and evaluated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and typical amperometric response (i-t) method. Exhilaratingly, the Cu-Ni(OH)₂/GCE shows significant electrocatalytic activity toward the reduction of H₂O₂. At an applied potential of −0.1 V, the sensor produces an ultrahigh sensitivity of 408.1 μA mM⁻¹ with a low detection limit of 1.5 μM (S/N = 3). The response time of the proposed electrode was less than 5 s. What's more, the proposed sensor displays excellent selectivity, good stability, and satisfying repeatability.