Characterisation of activated nanoporous carbon for supercapacitor electrode materials

Commercial nanoporous carbon RP-20 was activated with water vapor in the temperature range from 950 °C to 1150 °C. The XRD analysis was carried out on nanoporous carbon powder samples to investigate the structural changes (graphitisation) in modified carbon that occurred at activation temperatures T ? 1150 °C. The first-order Raman spectra showed the absorption peak at 1582 cm⁻¹ and the disorder (D) peak at 1350 cm⁻¹. The low-temperature N₂ adsorption experiments were performed at −196 °C and a specific surface area up to 2240 m²g⁻¹ for carbon activated at T = 1050 °C was measured. The cell capacitance for two electrode activated nanoporous carbon system advanced up to 60 F g⁻¹ giving the specific capacitance ∼240 F g⁻¹ to one electrode nanoporous carbon ∣1.2 M (C₂H₅)₃CH₃NBF₄ + acetonitrile solution interface. A very wide region of ideal polarisability for two electrode system (∼3.2 V) was achieved. The low frequency limiting specific capacitance very weakly increases with the rise of specific area explained by the mass transfer limitations in the nanoporous carbon electrodes. The electrochemical characteristics obtained show that some of these materials under discussion can be used for compilation of high energy density and power density non-aqueous electrolyte supercapacitors with higher power densities than aqueous supercapacitors.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Investigation of polymer electrolyte hybrid supercapacitor based on manganese oxide-carbon electrodes

A hybrid supercapacitor based on manganese oxide, activated carbon and polymer electrolyte was developed and electrochemically investigated. The capacitive performance obtained from the polymer electrolyte based supercapacitor was similar to that of an aqueous electrolyte based supercapacitor, tested for comparison in the same operative conditions. A durability test carried out for 2500 cycles showed stable and slowly increasing performance. The specific capacitance of hybrid supercapacitor was 48 F g⁻¹ (192 F g⁻¹ as a mean one electrode capacitance), in which that of the positive electrode was 384 F g⁻¹ of MnO₂ and that of negative electrode 117 F g⁻¹ of carbon. The impedance analysis evidenced that although the polymer electrolyte based hybrid supercapacitor showed higher resistance compared to that of the liquid electrolyte based supercapacitor, this drawback was counterbalanced by better ion transport features, which were evident at lower frequencies, where similar values of capacitances were obtained from the different supercapacitors.     

A novel nickel-based mixed rare-earth oxide/activated carbon supercapacitor using room temperature ionic liquid electrolyte

Mesopore nickel-based mixed rare-earth oxide (NMRO) and activated carbon (AC) with rich oxygen-contained groups were prepared as electrode materials in a supercapacitor using room temperature ionic liquid (RTIL) electrolyte. These electrode materials were characterized by XPS, XRD, N₂ adsorption, SEM as well as various electrochemical techniques, and showed good properties and operated well with RTIL electrolyte. A 3 V asymmetrical supercapacitor was fabricated, which delivered a real power density of 458 W kg⁻¹ as well as a real energy density of 50 Wh kg⁻¹, and during a 500-cycle galvanostatic charge/discharge measurement, no capacity decay was visible. Such promising energy-storage performance was to a large extent ascribed to nonvolatile RTIL electrolyte with wide electrochemical windows and high stable abilities worked with both electrode materials.     

Electric double layer capacitors with gelled polymer electrolytes based on poly(ethylene oxide) cured with poly(propylene oxide) diamines

Using a gel electrolyte for electric double layer capacitors usually encountered a drawback of poor contact between the electrolyte and the electrode surface. A gel electrolyte consisting of poly(ethylene oxide) crosslinked with poly(propylene oxide) as a host, propylene carbonate (PC) as a plasticizer, and LiClO₄ as a electrolytic salt was synthesized for double layer capacitors. Diglycidyl ether of bisphenol-A was blended with the polymer precursors to enhance the mechanical properties and increase the internal free volume. This gel electrolyte showed an ionic conductivity as high as 2 × 10⁻³ S cm⁻¹ at 25 °C and was electrochemically stable over a wide potential range (ca. 5 V). By sandwiching this gel-electrolyte film with two activated carbon cloth electrodes (1100 m² g⁻¹ in surface area), we obtained a capacitor with a specific capacitance of 86 F g⁻¹ discharged at 0.5 mA cm⁻², while the capacitance was 82 F g⁻¹ for a capacitor equipped with a liquid electrolyte of 1 M LiClO₄/PC. The capacitance decrease with the current density was less significant for the gel-electrolyte capacitor. We found that the less restricted ion diffusion near the electrolyte/electrode interface led to the smaller overall resistance of the gel-electrolyte capacitor. The high performance of the gel-electrolyte capacitor has demonstrated that the developed polymer network not only facilitated ion motion in the electrolyte bulk phase but also gave an intimate contact with the carbon surface. The side chains of the polymer in the amorphous phase could stretch across the boundary layer at the electrolyte/electrode interface to come into contact with the carbon surface, thus improving transport of Li⁺ ions by the segmental mobility in polymer.     

Direct electrochemistry of guanosine on multi-walled carbon nanotubes modified carbon ionic liquid electrode

A multi-walled carbon nanotubes (MWCNTs) modified carbon ionic liquid electrode (CILE) was fabricated and used to investigate the electrochemical behavior of guanosine. CILE was prepared by mixing hydrophilic ionic liquid 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF₄), graphite powder and liquid paraffin together. The fabricated MWCNTs/CILE showed great electrocatalytic ability to the oxidation of guanosine and an irreversible oxidation peak appeared at 1.067 V (vs. SCE) with improved peak current. The electrochemical behavior of guanosine on the MWCNTs/CILE was carefully studied by cyclic voltammetry and the electrochemical parameters such as the charge transfer coefficient (α) and the electrode reaction standard rate constant (k_s) were calculated with the result as 0.66 and 2.94 × 10⁻⁴ s⁻¹, respectively. By using differential pulse voltammetry (DPV) as the detection method, a linear relationship was obtained between the oxidation peak current and the guanosine concentration in the range from 1.0 × 10⁻⁷ to 4.0 × 10⁻⁵ mol/L with the detection limit as 7.8 × 10⁻⁸ mol/L (3σ). The common coexisting substances showed no interferences to the guanosine detection and the modified electrode showed good ability to distinguish the electrochemical response of guanosine and adenosine.     

A new amperometric glucose biosensor based on platinum nanoparticles/polymerized ionic liquid-carbon nanotubes nanocomposites

A new amperometric glucose biosensor has been developed based on platinum (Pt) nanoparticles/polymerized ionic liquid-carbon nanotubes (CNTs) nanocomposites (PtNPs/PIL-CNTs). The CNTs was functionalized with polymerized ionic liquid (PIL) through directly polymerization of the ionic liquid, 1-vinyl-3-ethylimidazolium tetrafluoroborate ([VEIM]BF₄), on carbon nanotubes and then used as the support for the highly dispersed Pt nanoparticles. The electrochemical performance of the PtNPs/PIL-CNTs modified glassy carbon (PtNPs/PIL-CNTs/GC) electrode has been investigated by typical electrochemical methods. The PtNPs/PIL-CNTs/GC electrode shows high electrocatalytic activity towards the oxidation of hydrogen peroxide. Taking glucose oxidase (GOD) as the model, the resulting amperometric glucose biosensor shows good analytical characteristics, such as a high sensitivity (28.28 μA mM⁻¹ cm⁻²), wide linear range (up to 12 mM) and low detection limit (10 μM).     

Highly mesoporous carbonaceous material of activated carbon beads for electric double layer capacitor

The activated carbon beads (ACB) are prepared by a new preparation method, which is proposed by mixing the coal tar pitch and fumed silica powder at a certain weight ratio and activation by KOH at different weight ratios and different temperatures. The BET surface area, pore volume and average pore size are obtained based on the nitrogen adsorption isotherms at 77 K by using ASAP 2010 apparatus. The results show that our samples have much high specific surface area (SSA) of 3537 m² g⁻¹and high pore volume value of 3.05 cm³ g⁻¹. The percentage of mesopore volume increases with the weight ratio of KOH/ACB ranging from 4% to 72%. The electrochemical double layer capacitors (EDLCs) are assembled with resultant carbon electrode and electrolyte of 1 mol L⁻¹ Et₄NBF₄/PC. The specific capacitance of the ACB sample could be as high as 191.7 F g⁻¹ by constant current charge/discharge technique, indicating that the ACB presents good characteristics prepared by the method proposed in this work. The investigation of influence of carbon porosity structure on capacitance indicates that the SSA plays an important role on the capacitance and all the pore sizes of less than 1 nm, from 1 to 2 nm and larger than 2 nm contribute to the capacitance. Mesopore structure is beneficial for the performance at high current density.     

Graphene nanosheets as electrode material for electric double-layer capacitors

Graphene nanosheets (GNSs) with narrow mesopore distribution around 4 nm were mass-produced from natural graphite via the oxidation and rapid heating processes. The effects of oxidant addition on the morphology, structure and electrochemical performance of GNSs as electrode materials for electric double-layer capacitor (EDLC) were systematically investigated. The electrochemical properties of EDLC were influenced by the specific surface area, pore characteristics, layer stacking and oxygen-containing functional group contents of electrode materials. Deeper oxidation makes graphite possess both higher specific surface area and more graphene edges, which are favorable for the enhancement of capacitive performance of EDLC. The electrodes with freestanding graphene nanosheets prepared by coating method exhibited good rate capability and reversibility at high scan rates (to 250 mV s⁻¹) in electrochemical performances. GNS electrode with specific surface area of 524 m² g⁻¹ maintained a stable specific capacitance of 150 F g⁻¹ under specific current of 0.1 A g⁻¹ for 500 cycles of charge/discharge.     

Factors influencing MnO2/multi-walled carbon nanotubes composite's electrochemical performance as supercapacitor electrode

Poor crystallined α-MnO₂ grown on multi-walled carbon nanotubes (MWCNTs) by reducing KMnO₄ in ethanol are characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and Brunauer-Emmett-Telle (BET) surface area measurement, which indicate that MWCNTs are wrapped up by poor crystalline MnO₂ and BET areas of the composites maintain the same level of 200 m² g⁻¹ as the content of MWCNTs in the range of 0-30%. The electrochemical performances of the MnO₂/MWCNTs composites as electrode materials for supercapacitor are evaluated by cyclic voltammetry (CV) and galvanostatic charge-discharge measurement in 1 M Na₂SO₄ solution. At a scan rate of 5 mV s⁻¹, rectangular shapes could only be observed for the composites with higher MWCNTs contents. The effect of additional conductive agent KS6 on the electrochemical behavior of the composites is also studied. With a fixed carbon content of 25% (MWCNTs included), MnO₂ with 20% MWCNTs and 5% KS6 has the highest specific capacitance, excellent cyclability and best rate capability, which gives the specific capacitance of 179 F g⁻¹ at a scan rate of 5 mV s⁻¹, and remains 114.6 F g⁻¹ at 100 mV s⁻¹.     

Optimisation of supercapacitors using carbons with controlled nanotexture and nitrogen content

In order to optimize the performance of supercapacitors, the capacitance of the carbon materials used as electrodes was strictly related to their pores size and also to their redox properties. Well-sized carbons have been elaborated through a template technique using mesoporous silica. For a series of template carbons, a perfect linear dependence has been found for the capacitance values versus the micropore volume determined by CO₂ adsorption. The redox properties of carbons were enhanced by substituting nitrogen for carbon up to ca. 7 wt.%. For carbons with similar nanotextural characteristics, the electrochemical measurements showed a proportional increase of the specific capacitance with the nitrogen content in acidic electrolyte. For an activated carbon from polyacrylonitrile with a specific surface area of only 800 m² g⁻¹, but with a nitrogen content of 7 wt.%, the capacitance reaches 160 F g⁻¹, with very little fading during cycling.     

Cycling stability of a hybrid activated carbon//poly(3-methylthiophene) supercapacitor with N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide ionic liquid as electrolyte

A long cycle-life, high-voltage supercapacitor featuring an activated carbon//poly(3-methylthiophene) hybrid configuration with N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide ionic liquid, a solvent-free green electrolyte, was developed. The cyclability of a laboratory scale cell with electrode mass loading sized for practical uses was tested at 60 °C over 16,000 galvanostatic charge-discharge cycles at 10 mA cm⁻² in the 1.5 and 3.6 V voltage range. The reported average and maximum specific energy and power, specific capacitance and capacity, equivalent series resistance and coulombic efficiency over cycling demonstrate the long-term viability of this ionic liquid as green electrolyte for high-voltage hybrid supercapacitors.     

Fast and reversible surface redox reaction of graphene-MnO2 composites as supercapacitor electrodes

We present a quick and easy method to synthesize graphene-MnO₂ composites through the self-limiting deposition of nanoscale MnO₂ on the surface of graphene under microwave irradiation. These nanostructured graphene-MnO₂ hybrid materials are used for investigation of electrochemical behaviors. Graphene-MnO₂ composite (78 wt.% MnO₂) displays the specific capacitance as high as 310 F g⁻¹ at 2 mV s⁻¹ (even 228 F g⁻¹ at 500 mV s⁻¹), which is almost three times higher than that of pure graphene (104 F g⁻¹) and birnessite-type MnO₂ (103 F g⁻¹). Interestingly, the capacitance retention ratio is highly kept over a wide range of scan rates (88% at 100 mV s⁻¹ and 74% at 500 mV s⁻¹). The improved high-rate electrochemical performance may be attributed to the increased electrode conductivity in the presence of graphene network, the increased effective interfacial area between MnO₂ and the electrolyte, as well as the contact area between MnO₂ and graphene.     

Facile solvothermal synthesis of a graphene nanosheet-bismuth oxide composite and its electrochemical characteristics

This work demonstrates a novel and facile route for preparing graphene-based composites comprising of metal oxide nanoparticles and graphene. A graphene nanosheet-bismuth oxide composite as electrode materials of supercapacitors was firstly synthesized by thermally treating the graphene-bismuth composite, which was obtained through simultaneous solvothermal reduction of the colloidal dispersions of negatively charged graphene oxide sheets in N,N-dimethyl formamide (DMF) solution of bismuth cations at 180 °C. The morphology, composition, and microstructure of the composites together with pure graphite oxide, and graphene were characterized using powder X-ray diffraction (XRD), FT-IR, field emission scanning electron microscopy (FESEM), transmission electron microscope (TEM), thermogravimetry and differential thermogravimetry (TG-DTG). The electrochemical behaviors were measured by cyclic voltammogram (CV), galvanostatic charge-discharge and electrochemical impedance spectroscopy (EIS). The specific capacitance of 255 F g⁻¹ (based on composite) is obtained at a specific current of 1 A g⁻¹ as compared with 71 F g⁻¹ for pure graphene. The loaded-bismuth oxide achieves a specific capacitance as high as 757 F g⁻¹ even at 10 A g⁻¹. In addition, the graphene nanosheet-bismuth oxide composite electrode exhibits the excellent rate capability and well reversibility.     

Electrochemical enhancement of adsorption capacity of activated carbon fibers and their surface physicochemical characterizations

The adsorption of activated carbon fibers (ACFs) and their surface characteristics were investigated before and after electrochemical polarization. The adsorption kinetics of m-cresol showed the dependence on polarized potential, and the adsorption rate constant increased by 77.1%, from 6.38 × 10⁻³ min⁻¹ at open-circuit (OC) to 1.13 × 10⁻² min⁻¹ at polarization of 600 mV. The adsorption isotherms at different potentials were in good agreement with Langmuir isotherm model, and the maximum adsorption capacity increased from 2.28 mmol g⁻¹ at OC to 3.67 mmol g⁻¹ at polarized potential of 600 mV. These indicated that electrochemical polarization could effectively improve the adsorption rate and capacity of ACFs. The surface characteristics of ACFs before and after electrochemical polarization were evaluated by N₂ adsorption-desorption isotherms, scanning electron microscope (SEM), zeta potential and Fourier transform infrared spectroscopy (FTIR). The results showed that the BET specific surface area and pore size increased as the potential rose. However, the surface chemical properties of ACFs hardly changed under electrochemical polarization of less than 600 mV. This study was beneficial to understand the mechanism of electrochemically enhanced adsorption.     

Porous carbons prepared by using metal-organic framework as the precursor for supercapacitors

Several kinds of porous carbons were easily prepared by using metal-organic framework as both template and carbon precursor. Nanocasting is chosen to adjust the textures and structures with phenolic resin or carbon tetrachloride and ethylenediamine as the additional carbon sources. The carbon materials were further activated by potassium hydroxide (KOH). The electrochemical capacitance behaviors of these carbon materials were investigated in both aqueous and organic electrolytes. Energy densities of 9.4 W h kg⁻¹ in 6 M KOH and 31.2 W h kg⁻¹ in 1.5 M tetraethylammonium tetrafluoroborate acetonitrile solution can be obtained for one of the prepared porous carbon materials (MAC-A) with the surface area of 2222 m² g⁻¹ and the total pore volume of 1.14 cm³ g⁻¹. Due to its high packing density of 0.93 g cm⁻³, the related volumetric specific energy densities of 8.8 and 29.0 W h L⁻¹ can be got.     

Direct electrochemistry of horseradish peroxidase in gelatin-hydrophobic ionic liquid gel films

The direct electrochemistry and electrocatalysis of horseradish peroxidase (HRP) immobilized on a gelatin - N, N-dimethylformamide (DMF) - hydrophobic ionic liquid (i.e. 1-octyl-3-methylimidazolium hexafluorophsohate) gel film coated glassy carbon electrode has been studied for the first time. The immobilized HRP exhibits a pair of well-defined quasi-reversible peaks in pH 7.0 phosphate buffer solutions, which results from the direct electron transfer between the enzyme and the underlying electrode. In this case there is about 2.7% of the immobilized HRP undergoing the electrochemical reaction, which corresponds to multi-layer of HRP on the electrode surface. The HRP immobilized has higher thermal stability than in gelatin hydrogel. Experiment results also show that the voltammetric behavior of the enzyme electrode depends on the type of room temperature ionic liquid (RTIL) used. When a more hydrophobic RTIL is adopted, the resulting enzyme electrode gives better performance. In the presence of hydrogen peroxide, the enzyme electrode shows sensitive response. The sensitivity of the catalytic peak is up to 1.38 A cm⁻² M⁻¹ and the Michaelis constant is down to 6.84 × 10⁻⁵ M, which are superior to that reported elsewhere. In addition, the UV-visible spectra of HRP entrapped in different films and the mass transfer of hydrogen peroxide are discussed as well.     

Electrode properties of a double layer capacitor of nano-structured graphite produced by ball milling under a hydrogen atmosphere

Nano-structural graphite prepared by ball milling under H₂ or Ar atmosphere was studied as an electrode for electric double layer capacitors (EDLCs) by means of a conventional 2-electrode galvanostatic method. Especially, the product prepared under H₂ atmosphere using zirconia balls revealed 500 m² g⁻¹ surface area and showed 12 F g⁻¹ specific capacitance, which was comparable to that of an activated carbon with large specific surface area of 3000 m² g⁻¹ examined as a reference. A proper condition of the milling time is rather a shorter time than ∼8 h, where the graphitic feature is remained in the ball milled product. On the other hand, for the sample prepared by using steel balls, the specific capacitance per surface area was several hundreds times smaller than the others, indicating that the small amount of Fe contamination during milling played a negative role for the EDLC properties.     

Preparation and electrochemical performance of polyaniline-based carbon nanotubes as electrode material for supercapacitor

Nitrogen-containing carbon nanotubes (CNTs) with open end and low specific surface area were prepared via the carbonization of polyaniline (PANI) nanotubes synthesized by a rapidly mixed reaction. On the basis of analyzing the morphologies and structures of the original and carbonized PANI nanotubes, the electrochemical properties of PANI-based CNTs obtained at different temperatures as electrode materials for supercapacitors using 30 wt.% aqueous solution of KOH as electrolyte were investigated by galvanostatic charge/discharge and cyclic voltammetry. It was found that the carbonized PANI nanotubes at 700 °C exhibit high specific capacitance of 163 F g⁻¹ at a current density of 0.1 A g⁻¹ and excellent rate capability in KOH solution. Using X-ray photoelectron spectroscopy measurement the nitrogen state and content in PANI-CNTs were analysed, which could play important roles for the enhancement of electrochemical performance. When the appropriate content of nitrogen is present, the presence of pyrrole or pyridone and quaternary nitrogen is beneficial for the improvement of electron mobility and the wettability of electrode.     

Electrochemical behaviors of thymine on a new ionic liquid modified carbon electrode and its detection

A new electrochemical method was proposed for the determination of thymine, which relied on the oxidation of thymine at a carbon ionic liquid electrode (CILE) in a pH 5.0 Britton-Robinson buffer solution. CILE was fabricated by using ionic liquid 1-(3-chloro-2-hydroxy-propyl)-3-methylimidazole acetate as the binder, which showed strong electrocatalytic ability to promote the oxidation of thymine. A single well-defined irreversible oxidation peak appeared with adsorption-controlled process and enhanced electrochemical response on the CILE, which was due to the presence of high conductive ionic liquid on the electrode. The reaction parameters of thymine were calculated with the electron transfer coefficient (α) as 0.27, the electron transfer number (n) as 1.23, the apparent heterogeneous electron transfer rate constant (k_s) as 6.87 × 10⁻⁶ s⁻¹ and the surface coverage (Г_T) as 5.71 × 10⁻⁸ mol cm⁻². Under the selected conditions the oxidation peak current was proportional to thymine concentration in the range from 3.0 to 3000.0 μM with the detection limit as 0.54 μM (3σ) by differential pulse voltammetry. The proposed method showed good selectivity to the thymine detection without the interferences of coexisting substances.