Improving the rate performance of LiFePO4 by Fe-site doping

LiFePO₄ doped by bivalent cation in Fe-sites show improved rate performance and cyclic stability. Under 10 C rate at room temperature, the capacities of LiFe_0.9M_0.1PO₄ (M = Ni, Co, Mg) maintain at 81.7, 90.4 and 88.7 mAh/g, respectively, in comparison with 53.7 mAh/g for undoped LiFePO₄ and 54.8 mAh/g for carbon-coated LiFePO₄ (LiFePO₄/C). The capacity retention is 95% after 100 cycles for doped samples while this value is only 70% for LiFePO₄ and LiFePO₄/C. Such a significant improvement in electrochemical performance should be partially related to the enhanced electronic conductivities (from 2.2 × 10⁻⁹ to <2.5 × 10⁻⁷ S cm⁻¹) and probably the mobility of Li⁺ ions in the doped samples.     

Synthesis of LiFePO4/C by solid-liquid reaction milling method

LiFePO₄/C was synthesized by the method of solid-liquid reaction milling, using FeCl₃·6H₂O, Li₂CO₃ and (NH₄)₂HPO₄ and glucose, which was used as reductant (carbon source). The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), TG-DTA analysis, infrared absorption carbon-sulfur analysis and electrochemical performance test. The sample synthesized at 680 °C for 8 h showed, at initial discharge, a capacity of 155.8, 153.2, 148.5, 132.7 mAh g^− 1 at 0.2 °C, 0.5 °C, 1 °C and 3 °C rate respectively. The sample also showed an excellent capacity retention as there was no significant capacity fade after 10 cycles.     

Enhanced electrochemical performance of nano-sized LiFePO4/C synthesized by an ultrasonic-assisted co-precipitation method

A simple and effective method, the ultrasonic-assisted co-precipitation method, was employed to synthesize nano-sized LiFePO₄/C. A glucose solution was used as the carbon source to produce in situ carbon to improve the conductivity of LiFePO₄. Ultrasonic irradiation was adopted to control the size and homogenize the LiFePO₄/C particles. The sample was characterized by X-ray powder diffraction, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). FE-SEM and TEM show that the as-prepared sample has a reduced particle size with a uniform size distribution, which is around 50 nm. A uniform amorphous carbon layer with a thickness of about 4-6 nm on the particle surface was observed, as shown in the HRTEM image. The electrochemical performance was demonstrated by the charge-discharge test and electrochemical impedance spectra measurements. The results indicate that the nano-sized LiFePO₄/C presents enhanced discharge capacities (159, 147 and 135 mAh g⁻¹ at 0.1, 0.5 and 2 C-rate, respectively) and stable cycling performance. This study offers a simple method to design and synthesis nano-sized cathode materials for lithium-ion batteries.     

Long-term cyclability of LiFePO4/carbon composite cathode material for lithium-ion battery applications

A simple high-energy ball milling combined with spray-drying method has been developed to synthesize LiFePO₄/carbon composite. This material delivers an improved tap density of 1.3 g/cm³ and a high electronic conductivity of 10⁻² to 10⁻³ S/cm. The electrochemical performance, which is especially notable for its high-rate performance, is excellent. The discharge capacities are as high as 109 mAh/g at the current density of 1100 mA/g (about 6.5C rate) and 94 mAh/g at the current density of 1900 mA/g (about 11C rate). At the high current density of 1700 mA/g (10C rate), it exhibits a long-term cyclability, retaining over 92% of its original discharge capacity beyond 2400 cycles. Therefore, the as-prepared LiFePO₄/carbon composite cathode material is capable of such large-scale applications as hybrid and plug-in hybrid electric vehicles.     

Effect of CeO2-coating on the electrochemical performances of LiFePO4/C cathode material

The effect of CeO₂ coating on LiFePO₄/C cathode material has been investigated. The crystalline structure and morphology of the synthesized powders have been characterized by XRD, SEM, TEM and their electrochemical performances both at room temperature and low temperature are evaluated by CV, EIS and galvanostatic charge/discharge tests. It is found that, nano-CeO₂ particles distribute on the surface of LiFePO₄ without destroying the crystal structure of the bulk material. The CeO₂-coated LiFePO₄/C cathode material shows improved lithium insertion/extraction capacity and electrode kinetics, especially at high rates and low temperature. At −20 °C, the CeO₂-coated material delivers discharge capacity of 99.7 mAh/g at 0.1C rate and the capacity retention of 98.6% is obtained after 30 cycles at various charge/discharge rates. The results indicate that the surface treatment should be an effective way to improve the comprehensive properties of the cathode materials for lithium ion batteries.     

Effect of milling method and time on the properties and electrochemical performance of LiFePO4/C composites prepared by ball milling and thermal treatment

Effects of ball milling way and time on the phase formation, particulate morphology, carbon content, and consequent electrode performance of LiFePO₄/C composite, prepared by high-energy ball milling of Li₂CO₃, NH₄H₂PO₄, FeC₂O₄ raw materials with citric acid as organic carbon source followed by thermal treatment, were investigated. Three ball milling ways and five different milling durations varied from 0 to 8 h were compared. LiFePO₄/C composites could be obtained from all synthesis processes. TEM examinations demonstrated LiFePO₄/C from ball milling in acetone resulted in sphere shape grains with a size of ∼60 nm, similar size was observed for LiFePO₄/C from dry ball milling but in a more irregular shape. The ball milling in benzene resulted in a much larger size of ∼250 nm. The LiFePO₄/C composites prepared from dry ball milling and ball milling in acetone showed much better electrochemical performance than that from ball milling in benzene. SEM examinations and BET measurements demonstrated that the high-energy ball milling effectively reduced the grain size. A ball milling for 4 h resulted in the best electrochemical performance, likely due to the proper amount of carbon and proper carbon structure were created.     

Properties of Li-graphite and LiFePO4 electrodes in LiPF6–sulfolane electrolyte

Sulfolane (also referred to as tetramethylene sulfone, TMS) containing LiPF₆ and vinylene carbonate (VC) was tested as a non-flammable electrolyte for a graphite |LiFePO₄ lithium-ion battery. Charging/discharging capacity of the LiFePO₄ electrode was ca. 150 mAh g⁻¹ (VC content 5 wt%). The capacity of the graphite electrode after 10 cycles establishes at the level of ca. 350 mAh g⁻¹ (C/10 rate). In the case of the full graphite |1 M LiPF₆ + TMS + VC 10 wt% |LiFePO₄ cell, both charging and discharging capacity (referred to cathode mass) stabilized at a value of ca. 120 mAh g⁻¹. Exchange current density for Li⁺ reduction on metallic lithium, estimated from electrochemical impedance spectroscopy (EIS) experiments, was j_o(Li/Li⁺) = 8.15 × 10⁻⁴ A cm⁻². Moreover, EIS suggests formation of the solid electrolyte interface (SEI) on lithium, lithiated graphite and LiFePO₄ electrodes, protecting them from further corrosion in contact with the liquid electrolyte. Scanning electron microscopy (SEM) images of pristine electrodes and those taken after electrochemical cycling showed changes which may be interpreted as a result of SEI formation. No graphite exfoliation was observed. The main decomposition peak of the LiPF₆ + TMS + VC electrolyte (TG/DTA experiment) was present at ca. 275 °C. The LiFePO₄(solid) + 1 M LiPF₆ + TMS + 10 wt% VC system shows a flash point of ca. 150 °C. This was much higher in comparison to that characteristic of a classical LiFePO₄ (solid) + 1 M LiPF₆ + 50 wt% EC + 50 wt% DMC system (T_f ≈ 37 °C).     

Electrochemical performance of Li3V2(PO4)3/C cathode material using a novel carbon source

Polyethylene glycol (PEG, mean molecular weight of 10,000) has been used to prepare a Li₃V₂(PO₄)₃/C cathode material by a simple solid-state reaction. The Raman spectra shows that the coating carbon has a good structure with a low I_D/I_G ratio. The images of SEM and TEM show that the carbon is dispersed between the Li₃V₂(PO₄)₃ particles, which improves the electrical contact between the corresponding particles. The electronic conductivity of Li₃V₂(PO₄)₃/C composite is 7.0 × 10⁻¹ S/cm, increased by seven orders of magnitude compared with the pristine Li₃V₂(PO₄)₃ (2.3 × 10⁻⁸ S/cm). At a low discharge rate of 0.28C, the sample presents a high discharge capacity of 131.2 mAh/g, almost achieving the theoretical capacity (132 mAh/g) for the reversible cycling of two lithium. After 500 cycles, the discharge capacity is 123.9 mAh/g with only 5.6% fading of the initial specific capacity. The Li₃V₂(PO₄)₃/C material also exhibits an excellent rate capability with high discharge capacities of 115.2 mAh/g at 1C and 106.4 mAh/g at 5C.     

Synthesis and characterization of high-density LiFePO4/C composites as cathode materials for lithium-ion batteries

To achieve a high-energy-density lithium electrode, high-density LiFePO₄/C composite cathode material for a lithium-ion battery was synthesized using self-produced high-density FePO₄ as a precursor, glucose as a C source, and Li₂CO₃ as a Li source, in a pipe furnace under an atmosphere of 5% H₂-95% N₂. The structure of the synthesized material was analyzed and characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical properties of the synthesized LiFePO₄/carbon composite were investigated by cyclic voltammetry (CV) and the charge/discharge process. The tap-density of the synthesized LiFePO₄/carbon composite powder with a carbon content of 7% reached 1.80 g m⁻³. The charge/discharge tests show that the cathode material has initial charge/discharge capacities of 190.5 and 167.0 mAh g⁻¹, respectively, with a volume capacity of 300.6 mAh cm⁻³, at a 0.1C rate. At a rate of 5C, the LiFePO₄/carbon composite shows a high discharge capacity of 98.3 mAh g⁻¹ and a volume capacity of 176.94 mAh cm⁻³.     

Process investigation, electrochemical characterization and optimization of LiFePO4/C composite from mechanical activation using sucrose as carbon source

LiFePO₄/C composite was synthesized by mechanical activation using sucrose as carbon source. High-energy ball milling facilitated phase formation during thermal treatment. TG-DSC and TPR experiments demonstrated sucrose was converted to CH_x intermediate before completely decomposed to carbon. Ball milling time, calcination temperature and dwelling time all had significant impact on the discharge capacity and rate performance of the resulted power. The optimal process parameters are high-energy ball milling for 2-4 h followed by thermal treatment at 700 °C for 20 h. The product showed a capacity of 174 mAh/g at 0.1C rate and around 117 mAh/g at 20C rate with the capacity fade less than 10% after 50 cycles. Too low calcination temperature or insufficient calcination time, however, could result in the residual of CH_x in the electrode and led to a decrease of electrode performance.     

Structure optimization and the structural factors for the discharge rate performance of LiFePO4/C cathode materials

Carbon coating and iron phosphides of high electron conductivity were introduced into the LiFePO₄ materials which were derived via a sol-gel method in order to improve the high discharge rate performance. The start constituents were FeC₂O₄·2H₂O, LiOH·H₂O, NH₄H₂PO₄ and ethylene glycol. Effects of the calcination temperature and the ethylene glycol on the structure and the electrochemical performance of the LiFePO₄ materials were investigated. Structure analyses showed that the addition of ethylene glycol caused an obvious decrease in the particle size of LiFePO₄. Calcination temperature and ethylene glycol jointly affected the formation of iron phosphides. Combining the electrochemical testing, it was found that, at low discharge rate, small particle size and high content of LiFePO₄ were much important for the capacity rather than the iron phosphides, and relative high content of Fe₂P (e.g. 8 wt.%) even worsened the capacity. However, with the increase of the discharge rate, the high electron conductive iron phosphides turned to play important role on the capacity. Fe₂P effectively increased both the reaction and diffusion kinetics and hence enhanced the utilization efficiency of the LiFePO₄ at high discharge rate. Combining relative small particle size, even 2 wt.% of iron phosphides could improve the high rate performance of LiFePO₄/C significantly.     

Design and synthesis of high-rate micron-sized, spherical LiFePO4/C composites containing clusters of nano/microspheres

A micron-sized LiFePO₄/C composite with a spherical morphology was reduced carbothermally from precursor particles prepared by ball milling-assisted spray-drying. The specific capacity of the electrode at a 10 C (1700 mA/g) rate was 110 mAh/g and a high voltage plateau was achieved. The high-rate performance of the composite electrode was due to its unique spherical structure, comprising clusters of nano- or sub-micron-sized spherical particles. This morphology increases the effective conductive surface area, reduces the charge-transfer reaction resistance and improves the diffusion of lithium ions.     

Synthesis of FePO4·xH2O for fabricating submicrometer structured LiFePO4/C by a co-precipitation method

Amorphous hydrated iron (III) phosphate has been synthesized by a coordinate precipitation method from equimolecular Fe(NO₃)₃ and (NH₄)₂HPO₄ solutions at an elevated temperature. Hydrated iron (III) phosphate samples and the corresponding LiFePO₄/C products were characterized by XRD and SEM. The electrochemical behavior was studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The LiFePO₄/C fabricated from as-synthesized FePO₄ delivered discharge capacities of 162.5, 147.3, 133.0, 114.7, 97.2, 91.3 and 88.5 mAh g⁻¹ at rates of 0.1C, 0.2C, 0.5C, 1C, 2C, 3C and 4C with satisfactory capacity retention, respectively.     

Kinetic behavior of LiFePO4/C cathode material for lithium-ion batteries

The composite cathode materials of LiFePO₄/C were synthesized by spray-drying and post-annealing method. The crystalline structure and morphology of products were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The charge-discharge kinetics of LiFePO₄/C electrode was investigated using electrochemical impedance spectroscopy (EIS). The results show that the increment of the resistance has a close relation to the appearance of the FePO₄ phase during charge-discharge course, and that the ohmic resistance, charge transfer resistance and lithium-ion diffusion coefficients of the LiFePO₄/C electrode do not change much by extended cycling tests, implying a relatively superior cyclability of the battery. The effect of cell temperature on the electrochemical reaction behaviors of LiFePO₄/C electrode was also investigated using the EIS. It is confirmed that the effect of the cell temperature on the impedance results mainly from the enhancement of the lithium-ion diffusion at elevated temperatures.     

Improved electrochemical performance of La0.7Sr0.3MnO3 and carbon co-coated LiFePO4 synthesized by freeze-drying process

Carbon coated LiFePO₄ particles were first synthesized by sol-gel and freeze-drying method. These particles were then coated with La_0.7Sr_0.3MnO₃ nanolayer by a suspension mixing process. The La_0.7Sr_0.3MnO₃ and carbon co-coated LiFePO₄ particles were calcined at 400 °C for 2 h in a reducing atmosphere (5% of hydrogen in nitrogen). Nanolayer structured La_0.7Sr_0.3MnO₃ together with the amorphous carbon layer forms an integrate network arranged on the bare surface of LiFePO₄ as corroborated by high-resolution transmission electron microscopy. X-ray diffraction results proved that the co-coated composite still retained the structure of the LiFePO₄ substrate. The twin coatings can remarkably improve the electrochemical performance at high charge/discharge rates. This improvement may be attributed to the lower charge transfer resistance and higher electronic conductivity resulted from the twin nanolayer coatings compared with the carbon coated LiFePO₄.     

Preparation and characterization of nano-particle LiFePO4 and LiFePO4/C by spray-drying and post-annealing method

Pure, nano-sized LiFePO₄ and LiFePO₄/C cathode materials are synthesized by spray-drying and post-annealing method. The influence of the sintering temperature and carbon coating on the structure, particle size, morphology and electrochemical performance of LiFePO₄ cathode material is investigated. The optimum processing conditions are found to be thermal treatment for 10 h at 600 °C. Compared with LiFePO₄, LiFePO₄/C particles are smaller in size due to the inhibition of crystal growth to a great extent by the presence of carbon in the reaction mixture. And that the LiFePO₄/C composite coated with 3.81 wt.% carbon exhibits the best electrode properties with discharge capacities of 139.4, 137.2, 133.5 and 127.3 mAh g⁻¹ at C/5, 1C, 5C and 10C rates, respectively. In addition, it shows excellent cycle stability at different current densities. Even after 50 cycles at the high current density of 10C, a discharge capacity of 117.7 mAh g⁻¹ is obtained (92.4% of its initial value) with only a low capacity fading of 0.15% per cycle.     

High power performance of nano-LiFePO4/C cathode material synthesized via lauric acid-assisted solid-state reaction

A nano-LiFePO₄/C composite has been directly synthesized from micrometer-sized Li₂CO₃, NH₄H₂PO₄, and FeC₂O₄·2H₂O by the lauric acid-assisted solid-state reaction method. The SEM and TEM observations demonstrate that the synthesized nano-LiFePO₄/C composite has well-dispersed particles with a size of about 100–200 nm and an in situ carbon layer with thickness of about 2 nm. The prepared nano-LiFePO₄/C composite has superior rate capability, delivering a discharge capacity of 141.2 mAh g⁻¹ at 5 °C, 130.9 mAh g⁻¹ at 10 C, 121.7 mAh g⁻¹ at 20 °C, and 112.4 mAh g⁻¹ at 30 °C. At −20 °C, this cathode material still exhibits good rate capability with a discharge capacity of 91.9 mAh g⁻¹ at 1 °C. The nano-LiFePO₄/C composite also shows excellent cycling ability with good capacity retention, up to 100 cycles at a high current density of 30 °C. Furthermore, the effect of lauric acid in the preparation of nano-LiFePO₄/C composite was investigated by comparing it with that of citric acid. The SEM images reveal that the morphology of the LiFePO₄/C composite transformed from the porous structure to fine particles as the molar ratio of lauric acid/citric acid increased.     

Preparation and characterization of nano-sized LiFePO4 by low heating solid-state coordination method and microwave heating

The precursors of LiFePO₄ were prepared by low heating solid-state coordination method using lithium acetate, ammonium dihydric phosphate, ferrous oxalate and citric acid as raw materials. Olivine phase LiFePO₄ as a cathode material for lithium-ion batteries was successfully synthesized by microwave heating in a few minutes. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to characterize its structure and morphology. Cyclic voltammetry (CV) and charge-discharge cycling performance were used to characterize its electrochemical properties. The results showed that the grain size of the optimal sample was about 40-50 nm, and the as-prepared particles were homogeneous. The nano-sized LiFePO₄ obtained has a high electrochemical capacity (125 mAh g⁻¹) and stable cycle ability.     

Reaction mechanism and electrochemical performance of LiFePO4/C cathode materials synthesized by carbothermal method

Spray drying and carbothermal method was employed to investigate reaction mechanism and electrochemical performance of LiFePO₄/C cathode by using different carbon sources. Micro-structural variations of LiFePO₄/C precursors using different carbon sources were studied by Thermo-gravimetric (TG)/Differential Thermal Analysis (DTA). The LiFePO₄/C samples were characterized by X-ray diffraction (XRD) and Fourier transform infrared (FTIR) absorption spectroscopy. The results indicated that the crystallization temperature of LiFePO₄ was 453 °C, while the transform temperature was 539 °C from Li₃Fe₂(PO₄)₃ to LiFePO₄. At 840 °C, LiFePO₄/C sample with an excess of impurity phase Fe₂P gave much poorer electrochemical performance. The severe decomposition of LiFePO₄/C happened at 938 °C and generated impurity phases Li₄P₂O₇ and Fe₂P. The clear discharge platform of Fe₂P emerged at around 2.2 V.     

Synthesis and characterization of LiFePO4/(Ag + C) composite cathodes with nano-carbon webs

LiFePO₄/(Ag + C) composite cathodes with a new type of nano-sized carbon webs were synthesized by two methods of an aqueous co-precipitation and a sol-gel process, respectively. Simultaneous thermogravimetric-differential thermal analysis indicates that the crystallization temperature of LiFePO₄ is about 455-466 °C, which is close to the pyrolysis temperature of polypropylene, 460 °C. The silver and carbon co-modifying does not affect the olivine structure of LiFePO₄ but improves its kinetics in terms of discharge capacity and rate capability. Discharge capacities were improved from 153.4 mA h g^− 1 of LiFePO₄/C to 160.5 mA h g^− 1and 162.1 mA h g^− 1 for LiFePO₄/(Ag + C) cathodes synthesized by the co-precipitation and sol-gel methods, respectively. The possible reasons for the small difference in discharge capacity of two LiFePO₄/(Ag + C) cathodes were discussed. AC impedance measurements show that the Ag + C co-modification decreases the charge transfer resistance of LiFePO₄/(Ag + C) cathodes.