Electrochemical performances of lithium ion battery using alkoxides of group 13 as electrolyte solvent

Tris(methoxy polyethylenglycol) borate ester (B-PEG) and aluminum tris(polyethylenglycoxide) (Al-PEG) were used as electrolyte solvent for lithium ion battery, and the electrochemical property of these electrolytes were investigated. These electrolytes, especially B-PEG, showed poor electrochemical stability, leading to insufficient discharge capacity and rapid degradation with cycling. These observations would be ascribed to the decomposition of electrolyte, causing formation of unstable passive layer on the surface of electrode in lithium ion battery at high voltage. However, significant improvement was observed by the addition of aluminum phosphate (AlPO₄) powder into electrolyte solvent. AC impedance technique revealed that the increase of interfacial resistance of electrode/electrolyte during cycling was suppressed by adding AlPO₄, and this suppression could enhance the cell capabilities. We infer that dissolved AlPO₄ components formed electrochemically stable layer on the surface of electrode.     

Gel electrolytes based on lithium modified silica nano-particles

In this work lithium modified silica (Li-SiO₂) nano-particles were synthesized and used as a single ion lithium conductor source in gel electrolytes. It was found that Li-SiO₂ exhibited good compatibility with DMSO, DMA/EC (a mixture of N,N-dimethyl acetamide and ethylene carbonate) and the ionic liquid, N-methyl-N-propyl pyrrolidinium bis(trifluoromethylsulfonyl) amide ([C₃mpyr][NTf₂]). Several gel electrolytes based on Li-SiO₂ were obtained. These gel electrolytes were investigated by DSC, solid state NMR, conductivity measurements and cyclic voltammetry. Conductivities as high as 10⁻³ S/cm at room temperature were observed in these nano-particle gel electrolytes. The results of electrochemical tests showed that some of these materials were promising for using as lithium conductive electrolytes in electrochemical devices, with high lithium cycling efficiency evident.     

Compatibility of quaternary ammonium-based ionic liquid electrolytes with electrodes in lithium ion batteries

Electrochemical intercalation/deintercalation behavior of lithium into/from electrodes of lithium ion batteries was comparatively investigated in 1 mol/L LiClO₄ ethylene carbonate-diethyl carbonate (EC-DEC) electrolyte and a quaternary ammonium-based ionic liquid electrolyte. The natural graphite anode exhibited satisfactory electrochemical performance in the ionic liquid electrolyte containing 20 vol.% chloroethylenene carbonate (Cl-EC). This is attributed to the mild reduction of solvated Cl-EC molecules at the graphite/ionic electrolyte interface resulting in the formation of a thin and homogenous SEI on the graphite surface. However, rate capability of the graphite anode is poor due to the higher interfacial resistance than that obtained in 1 mol/L LiClO₄/EC-DEC organic electrolyte. Spinel LiMn₂O₄ cathode was also electrochemically cycled in the ionic electrolyte showing satisfactory capacity and reversibility. The ionic electrolyte system is thus promising for 4 V lithium ion batteries based on the concept of “greenness and safety”.     

Poly(vinylidene fluoride-hexafluoropropylene)/organo-montmorillonite clays nanocomposite lithium polymer electrolytes

Polymer-clay nanocomposite (PCN) materials were prepared by intercalation of an alkyl-ammonium ion spacing/coupling agent and a polymer between the planar layers of a swellable-layered material, such as montmorillonite (MMT). The nanocomposite lithium polymer electrolytes comprising such PCN materials and/or a dielectric solution (propylene carbonate) were prepared and discussed. The chemical composition of the nanocomposite materials was determined with X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy, which revealed that the alkyl-ammonium ion successfully intercalated the layer of MMT clay, and thus copolymer poly(vinylidene fluoride-hexafluoropropylene) entered the galleries of montmorillonite clay. Cyclic voltammetry and electrochemical impedance spectroscopy (EIS) were used to investigate the electrochemical properties of the lithium polymer electrolyte. Equivalent circuits were proposed to fit the EIS data successfully, and the significant contribution from MMT was thus identified. The resulting polymer electrolytes show high ionic conductivity up to 10⁻³ S cm⁻¹ after gelling with propylene carbonate. The PCN materials exhibit good electrochemical stability and could be potentially used in lithium secondary battery.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Measurement of transference numbers for lithium ion electrolytes via four different methods, a comparative study

We report here on comparative measurements of cationic transference numbers of some lithium battery related electrolytes including lithium tetrafluoroborate in propylene carbonate, lithium hexafluorophosphate in blends of ethylene carbonate/diethyl carbonate and ethylene carbonate/propylene carbonate/dimethyl carbonate, as well as lithium difluoromono (oxalate) borate in an ethylene carbonate/diethyl carbonate blend via four different methods. Whereas three electrochemical methods yield transference numbers decreasing with concentration in accordance with electrostatic theories, valid for low to intermediate concentrations of the electrolyte, nuclear magnetic resonance spectroscopy measurements show increasing transference numbers with increasing concentration. The discrepancy is attributed to effects of ion–ion and ion–solvent interaction.     

Effect of surface modified porous inorganic-organic hybrid polyphosphazene nanotubes on the properties of polyethylene oxide based solid polymer electrolytes

2-(2-methyloxyethoxy)ethanol modified poly (cyclotriphosphazene-co-4,4′-sufonyldiphenol) (PZS) nanotubes were synthesized and solid composite polymer electrolytes based on the surface modified polyphosphazene nanotubes added to PEO/LiClO₄ model system were prepared. Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM) were used to investigate the characteristics of the composite polymer electrolytes (CPE). The ionic conductivity, lithium ion transference number and electrochemical stability window can be enhanced after the addition of surface modified PZS nanotubes. The electrochemical investigation shows that the solid composite polymer electrolytes incorporated with PZS nanotubes have higher ionic conductivity and lithium ion transference number than the filler SiO₂. Maximum ionic conductivity values of 4.95 × 10⁻⁵ S cm⁻¹ at ambient temperature and 1.64 × 10⁻³ S cm⁻¹ at 80 °C with 10 wt % content of surface modified PZS nanotubes were obtained and the lithium ion transference number was 0.41. The good chemical properties of the solid state composite polymer electrolytes suggested that the inorganic-organic hybrid polyphosphazene nanotubes had a promising use as fillers in solid composite polymer electrolytes and the PEO₁₀-LiClO₄-PZS nanotubes solid composite polymer electrolyte can be used as a candidate material for lithium polymer batteries.     

Electrochemical performance of nanoporous Si as anode for lithium ion batteries in alkyl carbonate and ionic liquid-based electrolytes

Nanoporous Si was obtained by means of metal-assisted chemical etching. Li ion insertion–extraction was tested by voltammetric and galvanostatic electrochemical cycling in conventional 1 M LiPF₆ ethylene carbonate/dimethyl carbonate EC/DMC and in 1 M LiTFSI 1-butyl-1-methyl-pyrrolidinium bis (trifluoromethyl) sulfonylimide [BMP] [TFSI] electrolytes. The nanoporous Si demonstrated high reversibility when cycled in 1 M LiPF₆ EC/DMC electrolyte and showed superior activity compared to the non-structured sample. In contrast to the organic carbonate electrolyte, the material cycling in ionic liquid media showed reduced capacity and reversibility of the Li ion exchange. The latter results were discussed in terms of the high viscosity of the ionic liquid and ineffective cathodic passivation of the Si substrate in the ionic liquid-based electrolyte. Scanning electron microscopy imaging showed minor morphological changes due to the large volume change during Li insertion. No signs of crack formation and propagation were detected during the time span of the measurement.     

锂磷酸盐微晶玻璃固体电解质材料研究进展

锂磷酸盐微晶玻璃固体电解质具有合成简单,电化学稳定性高等优点,已经对其进行了大量的研究工作。结合近几年的研究,分别综述了三元、四元和五元3种不同系统的锂磷酸盐微晶玻璃固体电解质所具有的最大电导率。并描述了Nasicon结构的快离子导体和交流阻抗谱在计算电导率上的应用。锂磷酸盐微晶玻璃固体电解质在全固态锂离子电池中将会有更广泛的应用。     

A novel polymer electrolyte based on PMAML/PVDF-HFP blend

A gel polymer electrolyte based on the blend of poly(methyl methacrylate-co-acrylonitrile-co-lithium methacrylate) (PMAML) and poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) was prepared and characterized. The synthesized PMAML were characterized by FTIR and NMR, respectively, and the surface morphology of the PMAML and PVDF-HFP blend membrane was also observed by scanning electron microscope (SEM). The electrochemical properties of composite electrolyte membranes were studied. The ionic conductivity of the polymer electrolyte composed of 75 wt.% 1 M LiBF₄ in ethylene carbonate (EC) and dimethyl carbonate (DMC) (EC:DMC=1:1 by weight) was about 2.6×10⁻³ S cm⁻¹ at ambient temperature. The electrochemical window of the polymer electrolyte was about 4.6 V determined from the linear sweep voltammetry plot. The lithium ion polymer batteries were assembled by sandwiching gel polymer electrolyte between LiCoO₂ cathode and mesophase carbon fibre (MPCF) anode. Charge-discharge test results display that lithium ion batteries with these gel polymer electrolytes have good electrochemical performance.     

Low temperature performance of graphite electrode in Li-ion cells

We studied low temperature performance of Li/graphite cell. Results show that capacity of the graphite electrode falls significantly in the temperature range of 0 to −20 °C. When lithiation and delithiation are both carried out at −20 °C, graphite only retains 12% of the room temperature capacity. However, delithiation capacity of graphite increases to 92% of the room temperature value if the lithiation is carried out at room temperature. We believe that the poor low temperature performance of the cell is due to slow kinetics of lithium ion diffusion in graphite rather than low ionic conductivity of electrolyte and solid electrolyte interface (SEI) on the graphite surface. During lithiation and delithiation processes, lithium ion has the similar apparent chemical diffusion coefficient of 10⁻⁹-10⁻¹⁰ cm²/s at 20 °C, depending on the state of lithiation of graphite. We observed a dramatic decrease in lithium ion diffusivity in the temperature range of 0 to −20 °C, and that at low temperatures of <−20 °C, lithium ion has higher diffusivity in the delithiated graphite than in the lithiated one. We also observed that temperature dependence of cycling behavior of the Li/graphite cell follows the change of lithium ion diffusivity.     

Methyl phenyl bis-methoxydiethoxysilane as bi-functional additive to propylene carbonate-based electrolyte for lithium ion batteries

Methyl phenyl bis-methoxydiethoxysilane (MPBMDS) was prepared and its effects were investigated as an additive in 1.0 mol dm⁻³ LiPF₆-propylene carbonate (PC)/dimethyl carbonate (DMC) (1:1, v/v) electrolyte for lithium ion batteries. The electrochemical properties of the electrolyte with MPBMDS were characterized by discharge/charge tests, cyclic voltammetry, electrochemical impedance spectroscopy, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The addition of MPBMDS can effectively prevent the decomposition and the co-intercalation of PC. In addition, burning tests showed that the addition of 4–13 wt.% MPBMDS to the bare PC-based electrolyte effectively reduces the flammability. This eco-friendly compound provides a new promising direction for the development of bi- or multi-functional additives for lithium ion batteries.     

Characterization of solid polymer electrolytes based on poly(trimethylenecarbonate) and lithium tetrafluoroborate

The results of an investigation of a polymer electrolyte system based on the poly(trimethylene carbonate) host matrix, designated as p(TMC), with lithium tetrafluoroborate guest salt are described in this presentation. Electrolytes with lithium salt compositions with n between 3 and 80 (where n represents the number of (OCOCH₂CH₂CH₂O) units per lithium ion) were prepared by co-dissolution of salt and polymer in anhydrous tetrahydrofuran. The homogeneous solutions obtained by this procedure were evaporated, within a preparative glovebox and under a dry argon atmosphere, to form thin films of electrolyte.The solvent-free electrolyte films produced were obtained as very flexible, transparent, completely amorphous films and were characterized by measurements of total ionic conductivity, cyclic voltammetry, differential scanning calorimetry and thermogravimetry.     

Mixtures of ionic liquid and organic carbonate as electrolyte with improved safety and performance for rechargeable lithium batteries

In this paper we report the results of physical–chemical and electrochemical investigations performed on ternary mixtures of the room temperature ionic liquid (IL) N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (PYR₁₄TFSI), propylene carbonate (PC), and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as electrolyte for lithium-ion batteries. The thermal stability, ionic conductivity, viscosity and electrochemical stability windows of all considered mixtures were investigated and compared with those of electrolytes based on the pure PYR₁₄TFSI and PC. The mixtures were also used as electrolyte in combination with LiFePO₄-based electrodes. The specific capacity and cycling stability of these systems were investigated at different C-rates, both at room temperature and 60 °C.     

On the role of cyclic unsaturated additives on the behaviour of lithium metal electrodes in ionic liquid electrolytes

Three cyclic vinyl based additives, based respectively on oxygen, sulphur and fluorine, are tested for their ability to improve the cycling of lithium in a hostile ionic liquid medium. Oxygen based vinylene carbonate is found to offer the best protection of the lithium metal whilst allowing very consistent lithium cycling to occur. The vinylene carbonate based system under study is, however, imperfect. Lithium metal is deposited in a dendritic morphology, and vinylene carbonate is rapidly consumed during lithium cycling if it is present in a small quantity. Our results suggest that ionic liquid systems critically relying on a small amount of additive to protect a lithium electrode are not viable for long cycle life secondary batteries. It is suggested that an ionic liquid which itself is lithium metal compatible be used instead.     

锂电池离子液体电解质的研究进展

离子液体具有电导率高、热稳定性好、无污染、蒸气压极低等特性,是非常有希望应用于锂电池或电化学电容器的电解质。本文介绍了离子液体电解质体系在锂电池中的研究以及聚合物电解质一离子液体体系的研究进展。     

Li+电池固态聚合物电解质研究进展

固态聚合物电解质具有高安全性、高成膜性和黏弹性等优点,并与电极具有良好的接触性和相容性,是实现高安全性和高能量密度固态Li⁺电池的重要电解质体系。然而聚合物电解质室温离子电导率较低（10^-8~10^-6 S·cm^-1）,不能满足固态聚合物电池在常温运行的需求。因此,在提高离子电导率、机械强度和电化学稳定性等本征属性的基础上,同时探究改善电解质/电极的界面处及电极内部的离子输运是研发固态聚合物Li⁺电池面临的关键问题。主要从改性聚合物电解质用以提高Li⁺电池电化学性能的角度出发,综述了凝胶聚合物电解质、全固态聚合物电解质和复合固态电解质中的离子输运机制及其关键参数,总结了近年来聚合物电解质的最新研究进展和未来的发展方向。     

Synthesis and electrochemical properties of lithium methacrylate-based self-doped gel polymer electrolytes

In this study, a strategy for synthesizing lithium methacrylate (LiMA)-based self-doped gel polymer electrolytes was described and the electrochemical properties were investigated by impedance spectroscopy and linear sweep voltammetry. LiMA was found to dissolve in ethylene carbonate (EC)/diethyl carbonate (DEC) (3/7, v/v) solvent after complexing with boron trifluoride (BF₃). This was achieved by lowering the ionic interactions between the methacrylic anion and lithium cation. As a result, gel polymer electrolytes consisting of BF₃-LiMA complexes and poly(ethylene glycol) diacrylate were successfully synthesized by radical polymerization in an EC/DEC liquid electrolyte. The FT-IR and AC impedance measurements revealed that the incorporation of BF₃ into the gel polymer electrolytes increases the solubility of LiMA and the ionic conductivity by enhancing the ion disassociations. Despite the self-doped nature of the LiMA salt, an ionic conductivity value of 3.0 × 10⁻⁵ S cm⁻¹ was achieved at 25 °C in the gel polymer electrolyte with 49 wt% of polymer content. Furthermore, linear sweep voltammetry measurements showed that the electrochemical stability of the gel polymer electrolyte was around 5.0 V at 25 °C.     

Studies on cross-linked polyurethane acrylate-based electrolyte consisting of reactive vinyl/divinyl diluents

A series of cross-linked polyurethane acrylate (PUA) electrolytes have been prepared by using 4,4′-methylene bis(phenyl isocyanate), polyethylene glycol, hydroxyethyl methacrylate and different reactive vinyl/divinyl diluents, such as methyl methacrylate (MMA), ethyl acrylate and acrylonitrile, tripropylene glycol diacrylate (TPGDA). The electrolytes were prepared by UV radiation induced cross-linking of the PUA-diluent mixture followed by swelling in a liquid electrolyte (LP-30). Depending upon the composition of the components, these electrolytes exhibited a wide range of mechanical and electrical properties. The system containing MMA as reactive diluent showed highest conductivity, but poor mechanical properties and stability in the liquid electrolyte. The TPGDA cross-linked system possesses a good combination of ionic conductivity and stability in liquid electrolytes. These systems showed good compatibility with Li-electrodes and sufficient electrochemical stability to allow safe operation in rechargeable Li-batteries.     

Polyterthiophene/CNT composite as a cathode material for lithium batteries employing an ionic liquid electrolyte

A polyterthiophene (PTTh)/multi-walled carbon nanotube (CNT) composite was synthesised by in situ chemical polymerisation and used as an active cathode material in lithium cells assembled with an ionic liquid (IL) or conventional liquid electrolyte, LiBF₄/EC-DMC-DEC. The IL electrolyte consisted of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF₄) containing LiBF₄ and a small amount of vinylene carbonate (VC). The lithium cells were characterised by cyclic voltammetry (CV) and galvanostatic charge/discharge cycling. The specific capacity of the cells with IL and conventional liquid electrolytes after the 1st cycle was 50 and 47 mAh g⁻¹ (based on PTTh weight), respectively at the C/5 rate. The capacity retention after the 100th cycle was 78% and 53%, respectively. The lithium cell assembled with a PTTh/CNT composite cathode and a non-flammable IL electrolyte exhibited a mean discharge voltage of 3.8 V vs Li⁺/Li and is a promising candidate for high-voltage power sources with enhanced safety.