Study of the electroreduction of nitrate on copper in alkaline solution

The electrocatalytic activity of a Cu electrode for the electroreduction of nitrate in alkaline medium was investigated by linear sweep voltammetry at stationary and rotating disc electrodes. Nitrate-reduction products generated upon prolonged electrolyses at different potentials were quantified. In addition, adsorption phenomena associated with the nitrate electroreduction process were characterized by electrochemical quartz crystal microbalance (EQCM) experiments. This data revealed that nitrate electroreduction process strongly depends on the applied potential. Firstly, at ca. −0.9 V vs. Hg/HgO, the electroreduction of adsorbed nitrate anions to nitrite anions was identified as the rate-determining step of the nitrate electroreduction process. Between −0.9 and −1.1 V, nitrite is reduced to hydroxylamine. However, during long-term electrolyses, hydroxylamine is not detected and presumably because it is rapidly reduced to ammonia. At potential more negative than −1.1 V, nitrite is reduced to ammonia. At ca. −1.45 V, i.e. just before the hydrogen evolution reaction, the abrupt decrease of the cathodic current is due to the electrode poisoning by adsorbed hydrogen. In addition, during the first minutes of nitrate electrolysis, a decrease of the copper electrode activity was observed at the three investigated potentials (−0.9, −1.1 and −1.4 V). From polarization and EQCM measurements, this deactivation was attributed to the adsorption of nitrate-reduction products, blocking the electrode surface and slowing down the nitrate electroreduction rate. However, it was demonstrated that the Cu electrode can be reactivated by the periodic application of a square wave potential pulse at −0.5 V, which causes the desorption of poisoning species.     

Efficient electrochemical reduction of nitrate to nitrogen on tin cathode at very high cathodic potentials

The electrochemical reduction of nitrate on tin cathode at very high cathodic potentials was studied in 0.1 M K₂SO₄, 0.05 M KNO₃ electrolyte. A high rate of nitrate reduction (0.206 mmol min⁻¹ cm⁻²) and a high selectivity (%S) of nitrogen (92%) was obtained at −2.9 V versus Ag/AgCl. The main by-products were ammonia (8%) and nitrite (<0.02%). Small amounts of N₂O and traces of NO were also detected.As the cathodic potential increases, the %S of nitrogen increases, while that of ammonia displays a maximum at −2.2 V. The %S of nitrite decreases from 65% at −1.8 V to <0.02% at −2.4 V. The kinetic analysis indicated that the formation of nitrogen and ammonia proceeds through the intermediate nitrite.The reduction follows first order kinetics for both nitrate and nitrite at more cathodic potentials than −2.4 V, while at less negative potentials the kinetics is more complicated.The %Faradaic efficiency (%FE) of the reduction at −2.9 V was about 60% initially and decreased to 22% at 40 min.A cathodic corrosion of tin was observed, which was more intensive in the absence of nitrate. At potentials more negative than −2.4 V, small amounts of tin hydride were detected.     

Electrocatalytic reduction of nitrite using ferricyanide; Application for its simple and selective determination

The electrocatalytic reduction of nitrite has been studied by ferricyanide at the surface of carbon paste electrode. Cyclic voltammetry and chronoamperometry techniques were used to investigate the suitability of ferricyanide as a mediator for the electrocatalytic nitrite reduction in aqueous solution with various pH. Results showed that pH 0.00 is the most suitable for this purpose. In the optimum pH, the electrocatalytic ability about 700 mV can be seen and the homogeneous second-order rate constant (k_s) for nitrite coupled catalytically to ferricyanide was calculated 2.75 × 10³ M⁻¹ s⁻¹ by Nicholson-Shain method. Also, electron transfer coefficients (α) for ferricyanide was determined by using various electrochemical approaches such as Tafel plot in the absence and presence of nitrite 0.556 and 0.760, respectively. The catalytic reduction peak current was linearly dependent on the nitrite concentration and the linearity range obtained was 5.00 × 10⁻⁵ to 1.00 × 10⁻³ M. Detection limit has been found to be 2.63 × 10⁻⁵ M (2σ). This method has been applied as a selective, simple and precise method for determination of nitrite in real sample.     

Influence of the concentration and the nature of the supporting electrolyte on the electrochemical reduction of nitrate on tin cathode

The influences of the potential, the concentration and the nature of the supporting electrolyte on the rate of the reduction of nitrate on tin were studied by both voltammetry and constant potential electrolytic experiments.Both the rate of the reduction of nitrate and the yield of nitrogen increase as the negative potential increases from −1.8 to −2.8 V versus Ag/AgCl, while the yield of nitrite decreases. The yield of ammonia displays a maximum at −2.4 V and consequently decreases.The rate of the reduction at −1.8 V versus Ag/AgCl increases significantly as the concentration of NaCl increases. The cation of the supporting electrolyte increases the rate of the reduction along the series Li⁺ < Na⁺ < K⁺ < Cs⁺. Higher rates than that of the alkalimetals have been obtained in the presence of ammonium as well as of multivalent cations such as Ca²⁺ and La³⁺. The anion of the supporting electrolyte decreases the rate of the reduction in the order I⁻ > Br⁻ > Cl⁻ > F⁻ at −1.8 V.The experimental results were qualitatively explained by the Frumkin theory and additionally by the theory of the formation of ion pairs between the cation of the supporting electrolyte and the reacting nitrate.     

Influence of nitrate concentration on its electrochemical reduction on tin cathode: Identification of reaction intermediates

The influence of the concentration of nitrate in the range between 100 and 62,000 mg L⁻¹ NaNO₃ in NaCl solutions was studied under constant potential electrolysis at −2.8 V vs. Ag/AgCl. The rate of the reduction follows Langmuir-Hinshelwood kinetics, according to which zero order kinetics is followed at concentrations higher than 0.3 M whereas first order at lower concentrations.The selectivity to nitrogen increases from 70 to 83% as the concentration of nitrate increases from 100 to 1500 mg L⁻¹ and it remains almost constant for higher nitrate concentrations, whereas that of ammonia exhibits the opposite trend decreasing from 25 to 11%. The % Faradaic Efficiency (%FE) increased with the increase of the concentration of nitrate from 25% at 0.1 M to 78% at 1 M when 95% of nitrate was reduced in both cases. At high concentrations of nitrate, hyponitrite and hydroxylamine were detected as intermediates of the reduction and a reaction scheme which is in agreement with the experimental results has been proposed.The hydrogen evolution in our conditions probably takes place through the discharge of the cation of the supporting electrolyte instead of the Volmer-Tafel mechanism and the reduction of nitrate proceeds through electrochemical hydrogenation.     

Probing the electrochemical behaviour of SWCNT-cobalt nanoparticles and their electrocatalytic activities towards the detection of nitrite at acidic and physiological pH conditions

The electrochemical decoration of edge plane pyrolytic graphite electrode (EPPGE) with cobalt and cobalt oxide nanoparticles integrated with and without single-walled carbon nanotubes (SWCNTs) is described. Successful modification of the electrodes was confirmed by field emission scanning electron microscopy (FESEM), AFM and EDX techniques. The electron transfer behaviour of the modified electrodes was investigated in [Fe(CN)6]^3−/4− redox probe using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) and discussed. The study showed that cobalt nanoparticles modified electrodes exhibit faster electron transfer behaviour than their oxides. The catalytic rate constant (K) obtained at the EPPGE-SWCNT-Co for nitrite at pH 7.4 and 3.0 are approximately the same (∼3 × 10⁴ cm³ mol⁻¹ s⁻¹) while the limits of detection (LoD = 3.3δ/m) are in the μM order. From the adsorption stripping voltammetry, the electrochemical adsorption equilibrium constant β was estimated as (13.0 ± 0.1) × 10³ M⁻¹ at pH 7.4 and (56.7 ± 0.1) × 10³ M⁻¹ at pH 3.0 while the free energy change (ΔG°) due to the adsorption was estimated as −6.36 and −10.00 kJ mol⁻¹ for nitrite at pH 7.4 and 3.0, respectively.     

Studies based on the electrochemical response of 2-(2-nitrophenyl)-1H-benzimidazole at chemically modified electrodes with over-oxidized poly-1-naphthylamine

The development of a simple and efficient method to 2-(2-nitrophenyl)-1H-benzimidazole (NB) electrochemical determination using a polymer film coated chemically modified electrode is described. A glassy carbon (GC) electrode was modified employing an electro-polymerized film of 1-naphtylamine (1-NAP) followed by an over-oxidation treatment in 0.2 M sodium hydroxide solution (poly-1-NAPox electrode).The electrochemical behaviour of NB at the poly-1-NAPox electrode was investigated in a mixture of 10% ethanol + 90% buffer solution (pH 2) by cyclic voltammetry (CV) and square-wave voltammetry (SWV). The experimental results suggested that the poly-1-NAPox electrode had a good effect on NB electrochemical response because it avoided the electrode surface fouling as a consequence of the adsorption of NB reduction products, which was found when a bare GC electrode was employed as the working electrode. The NB cathodic current was dependent on the polymeric film over-oxidation degree (α).NB could be determined in the range from 2 × 10⁻⁶ to 5 × 10⁻⁵ M. The NB detection and quantification limits were 5 × 10⁻⁷ and 1.7 × 10⁻⁶ M, respectively. The percent relative standard deviation of the peak current to 10-replicated measurement using 1.2 × 10⁻⁵ M NB solution was 1.4%. The method showed to be rapid, simple and with a good sensitivity.     

Electrocatalytic reduction of nitrate on copper electrode in alkaline solution

This work is devoted to the study of the kinetics and reaction mechanism of nitrate reduction on a copper electrode in 0.1 M NaOH, which acts as the supporting electrolyte. The experimental methods include cyclic voltammetry (CV), cronoamperometry (CA), controlled-potential electrolysis (CPE), and coulometry. In CV, there are three potential regions where charge transfer reactions take place, reactions which are associated with NO₃⁻ and/or intermediates reduction. Two isopotential points observed in CV indicate the existence of some competitive adsorption processes at the electrode surface.The three charge transfer steps were also made evident in the CA, CPE and coulometry studies. The correlation of the experimental results with the literature data led to the conclusion that NO₃⁻ reduction on a copper electrode in 0.1 M NaOH has an intermediate (N₂O₂²⁻) species, which reduces to N₂ at a potential of about −1.3 V and to NH₄OH at potential values lower than −1.4 V (both values are vs. SCE).     

Electrochemical oxidation of nitrite on nanodiamond powder electrode

Nanodiamond (ND) powder electrodes were fabricated and the electrochemical properties were investigated in the solution containing nitrite in this article. This electrode exhibits substantial catalytic ability toward the oxidation of nitrite anions. The electrochemical oxidation mechanism of nitrite on the ND powder electrode is discussed. The oxidation of NaNO₂ is a two-electron transfer process. The electrode reaction rate constant k is estimated to be 2.013 × 10⁻⁴ cm/s and (1 − α)n_α is 0.1643. The peak current increases linearly with the rising of the concentration of NaNO₂.     

Kinetic study of nitrate reduction on Pt(1 1 0) electrode in perchloric acid solution

The kinetics of electrocatalytic reduction of nitrate on Pt(1 1 0) in perchloric acid was studied with cyclic voltammetry at a very low sweep rate of 1 mV s⁻¹, where pseudo-steady state condition was assumed to be achieved at each electrode potential. Stationary current-potential curves in perchloric acid in the absence of nitrate showed two peaks at 0.13 V and 0.23 V (RHE) in the so-called adsorbed hydrogen region. The nitrate reduction proceeded in the potential region of the latter peak in the pH range studied. The reaction orders with respect to NO₃⁻ and H⁺ were observed to be close to 0 and 1, respectively. The former value means that the adsorbed NO₃⁻ at a saturated coverage is one of the reactants in the rate-determining step (rds). The latter value means that hydrogen species is also a reactant above or on the rds. The Tafel slope of nitrate reduction was −66 mV per decade, which is taken to be approximately −59 mV per decade, indicating that the rds is a pure chemical reaction following electron transfer. We discuss two possible reaction schemes including bimolecular and monomolecular reactions in the rds to explain the kinetics and suggest that the reactants in the rds are adsorbed hydrogen and adsorbed NO₃⁻ with the assistance of the results in our recent report for nitrate reduction on Pt(S)[n(1 1 1) × (1 1 1)] electrodes: the nitrate reduction mechanism can be classified within the framework of the Langmuir-Hinshelwood mechanism.     

Optimization of process parameters for electrochemical nitrate removal using Box-Behnken design

Electrochemical reduction of nitrate in an undivided cell was studied in the present experiments. The optimization of the influencing factors on electrochemical reduction of nitrate by response surface methodology (RSM) was also studied. An ideal condition of performing both cathodic reduction of nitrate and anodic oxidation of the formed by-product in the presence of NaCl was achieved in the present experiment. The Box-Behnken design can be employed to develop mathematical models for predicting electrochemical nitrate removal geometry. The removal is sensitive to the current density and time in the present study. The value of R² > 0.99 for the present mathematical model indicates the high correlation between observed and predicted values. The optimal NaCl dosage, current density and electrolysis time for nitrate removal in the present experiment are 0.47 g L⁻¹, 26.06 mA cm⁻², and 111.88 min, respectively, at which the nitrate nitrogen (nitrate-N) and ammonia nitrogen (ammonia-N) concentration in the treated solution are 9.80 and 0 mg L⁻¹, respectively, which will meet the standards for drinking water.     

Synthesis, characterization and electroanalytical application of a new SiO2/SnO2 carbon ceramic electrode

A new SiO₂/SnO₂ carbon ceramic composite was prepared by the sol-gel method, and its potential application in electrochemistry as a novel electrode material has been studied. The prepared xerogel was structurally and electrochemically characterized by scanning electron microscopy coupled to energy dispersive spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction and cyclic voltammetry. The composite was pressed in a rigid disk-shape and used as a conductive substrate to immobilize a water-soluble organic-inorganic hybrid polymer, 3-n-propyl-4-picolinium chloride silsesquioxane. The oxidation of nitrite was studied on this polymer film coated electrode in aqueous solution using cyclic voltammetry and differential pulse voltammetry. This modified electrode exhibited a better defined voltammetric peak shifted negatively about 60 mV. The linear detection limit found for nitrite was from 1.3 × 10⁻⁵ to 1.3 × 10⁻³ mol l⁻¹ and the detection limit was 3.3 × 10⁻⁶ mol l⁻¹.     

Electrochemical modification of glassy carbon electrode by poly-4-nitroaniline and its application for determination of copper(II)

Electrochemical modification of glassy carbon (GC) electrode by poly-4-nitroaniline (P4NA), electrochemical reduction of P4NA and applicability of electrode modified in this way for determination of copper(II) (Cu(II)) is reported in this study. Electrochemical surface modification was performed by cyclic voltammetry in the potential range between +0.9 V and +1.4 V vs. Ag/Ag⁺ (in 10 mM AgNO₃) at the scan rate of 100 mV/s by 100 cycles in non-aqueous media. In order to provide electrochemical reduction of nitro groups on the P4NA-modified GC electrode surface (P4NA/GC), the cyclic voltammograms inducing/evidencing the reduction of nitro groups were performed in the potential range between −0.1 V and −0.8 V vs. Ag/AgCl/(sat.KCl) at the scan rate of 100 mV/s. The reduced P4NA/GC surfaces (Reduced-P4NA/GC) were treated with aqueous solution of nitrilotriacetic acid. The sensitivity of GC electrode modified in described way towards Cu(II) was investigated in Britton-Robinson buffer solution, pH 5.0. The potentiometric generic pulse technique was applied as innovative electrochemical method for detection of analytical signal. It was shown that GC electrodes modified in here described way will be suitable for the determination of Cu(II) in technological waste water and/or some other solutions containing Cu(II) ions.     

Electrochemical behavior of uranium(VI) in 1-butyl-3-methylimidazolium chloride and thermal characterization of uranium oxide deposit

The electrochemical behavior of uranyl nitrate in 1-butyl-3-methylimidazolium chloride at glassy carbon working electrode has been investigated in the temperature range 343-373 K by transient electrochemical techniques such as cyclic voltammetry, chronopotentiometry and square wave voltammetry. Influence of bulk concentration of uranium and temperature on the electroreduction and transport properties of U(VI) in bmimCl has been examined. Diffusion coefficient (D) and the energy of activation (E_a) of U(VI) in bmimCl has been estimated and is of the order of ∼10⁻⁸ cm²/s and 54 kJ/mol, respectively. Reduction of U(VI) takes place through an irreversible single step two-electron transfer to UO₂ deposit at glassy carbon working electrode. Thermal analysis of the uranium oxide indicated the entrapment of nearly 5% of electrolyte, bmimCl, during electrodeposition, which decomposes in the range 553-653 K.     

Experimental and theoretical studies of electrochemical characteristics of 3,4-dihydroxyphenylacetic acid (DOPAC)

The electrochemical behavior of 3,4-dihydroxyphenylacetic acid (DOPAC) in aqueous solutions with different pHs and DOPAC concentrations was studied by cyclic voltammetry at various potential scan rates. The electro-oxidation of DOPAC involves a transfer of two electrons and two protons in solutions of pH < 8.0 and a transfer of two electrons and one proton in solutions of pH > 8.0, in agreement with the one-step two-electron mechanism. The cyclic voltammetry indicated that the process of electro-oxidation of DOPAC follows an E_rC_i mechanism. The standard redox potential, E⁰′, two-proton-two-electron and one-proton-two-electron processes of DOPAC were determined as 0.585 and 0.357 V versus saturated calomel electrode (SCE), respectively. The acidic dissociation constant of DOPAC was also obtained. Also, the diffusion coefficient of DOPAC was calculated as 9.2 × 10⁻⁶ cm² s⁻¹ for the experimental conditions, using chronoamperometric results. The standard reduction potentials and the second acidic constant of DOPAC have been also calculated using standard ab initio calculations at the G3 level of theory in conjunction with a continuum solvation model. The theoretical values are in good agreement with experiment.     

Direct electrochemistry of guanosine on multi-walled carbon nanotubes modified carbon ionic liquid electrode

A multi-walled carbon nanotubes (MWCNTs) modified carbon ionic liquid electrode (CILE) was fabricated and used to investigate the electrochemical behavior of guanosine. CILE was prepared by mixing hydrophilic ionic liquid 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF₄), graphite powder and liquid paraffin together. The fabricated MWCNTs/CILE showed great electrocatalytic ability to the oxidation of guanosine and an irreversible oxidation peak appeared at 1.067 V (vs. SCE) with improved peak current. The electrochemical behavior of guanosine on the MWCNTs/CILE was carefully studied by cyclic voltammetry and the electrochemical parameters such as the charge transfer coefficient (α) and the electrode reaction standard rate constant (k_s) were calculated with the result as 0.66 and 2.94 × 10⁻⁴ s⁻¹, respectively. By using differential pulse voltammetry (DPV) as the detection method, a linear relationship was obtained between the oxidation peak current and the guanosine concentration in the range from 1.0 × 10⁻⁷ to 4.0 × 10⁻⁵ mol/L with the detection limit as 7.8 × 10⁻⁸ mol/L (3σ). The common coexisting substances showed no interferences to the guanosine detection and the modified electrode showed good ability to distinguish the electrochemical response of guanosine and adenosine.     

Electroreduction of nitrate ions on Pt(1 1 1) electrodes modified by copper adatoms

Kinetics and mechanism of nitrate ion reduction on Pt(1 1 1) and Cu-modified Pt(1 1 1) electrodes have been studied by means of cyclic voltammetry, potentiostatic current transient technique and in situ FTIRS in solutions of perchloric and sulphuric acids to elucidate the role of the background anion. Modification of platinum surface with copper adatoms or small amount of 3D-Cu crystallites was performed using potential cycling between 0.05 and 0.3 V in solutions with low concentration of copper ions, this allowed us to vary coverage θ_Cu smoothly. Following desorption of copper during the potential sweep from 0.3 to 1.0 V allowed us to estimate actual coverage of Pt surface with Cu adatoms. Another manner of the modification was also applied: copper was electrochemically deposited at several constant potentials in solutions containing 10⁻⁵ or 10⁻⁴ M Cu²⁺ and 5 mM NaNO₃ with registration of current transients of copper deposition and nitrate reduction.It has been found that nitrate reduction at the Pt(1 1 1) surface modified by copper adatoms in sulphuric acid solutions is hindered as compared to pure platinum due to induced sulphate adsorption at E < 0.3 V. Sulphate blocks the adsorption sites on the platinum surface and/or islands of epitaxial Cu(1 × 1) monolayer thus hindering the adsorption of nitrate anions and their reduction. The extent of inhibition weakly depends on the copper adatom coverage. Deposition of a small amount of bulk copper does not affect noticeably the rate of nitrate reduction.Nitrate reduction on copper-modified Pt(1 1 1) electrodes in perchloric acid solutions occurs much faster as compared to pure platinum. The steady-state currents are higher by 4 and 2 orders of magnitude at the potentials of 0.12 and 0.3 V, respectively. The catalytic effect of copper adatoms is largely caused by the facilitation of nitrate adsorption on the platinum surface near Cu_ad and/or on the islands of the Cu(1 × 1) monolayer (induced nitrate adsorption).Hydrogen adatoms block the adsorption sites on platinum for NO₃⁻ anion adsorption and inhibit reactions of nitrate reduction even at moderate surface coverage.The products of nitrate reduction in sulphuric and perchloric acids are essentially the same (NO and ammonia) irrespective of the presence or absence of Cu on the platinum surface.     

Electrochemical reduction of nitrate on Pt(S)[n(1 1 1) × (1 1 1)] electrodes in perchloric acid solution

The electrochemical reduction of nitrate ion was studied by cyclic voltammetry on Pt(1 1 1) and [n(1 1 1) × (1 1 1)] stepped Pt surfaces, where n (=14, 10, 7, 6, 5, 4, 3, 2) is the number of terrace atoms, in 0.1 M HClO₄ + 10 mM KNO₃. The electrocatalytic nitrate reduction was found to hardly proceed on Pt(1 1 1) in the hydrogen adsorption region, while the electrocatalytic activity was improved with the increase in the step density. Inactivation was observed in the presence of adsorbed hydrogen or nitrate-derived reduced adsorbate, i.e. adsorbed NO, on (1 1 1) step sites. It was, therefore, concluded that the electrocatalytically active NO₃⁻ species does not adsorb on the (1 1 1) terraces but on the (1 1 1) monoatomic steps. The nitrate reduction current increased with the step density in a non-linear relationship. The overall current density at 0.21 V (RHE) corresponding to the peak potential of the main electrocatalytic nitrate reduction wave which was maximum at n = 2, abruptly increased with short terraces, i.e. n < 5, where the current wave of adsorbed hydrogen on the Pt stepped surface with comparatively narrow (1 1 1) terraces, denoted as H_nt, also appeared unmodified for n < 5 on voltammograms recorded in 0.1 M HClO₄ in the absence of nitrate.     

Cobalt hydroxide film deposited on glassy carbon electrode for electrocatalytic oxidation of hydroquinone

The electrodeposition of cobalt hydroxide film on glassy carbon electrode was prepared by electrochemical method in an alkaline aqueous solution. The electrochemical behavior of hydroquinone on cobalt hydroxide film electrode has been investigated by using cyclic voltammetry and linear sweep voltammetry. The results showed that the film electrode has good electrocatalytic ability for the oxidation of hydroquinone to p-quinone. The recovery of hydroquinone from sample ranged from 94.7% to 102.9% and a rectilinear analytical curve for hydroquinone concentration from 5.0 × 10⁻⁶ to 1.25 × 10⁻⁴ mol/L was obtained. The detection limit was 5.0 × 10⁻⁷ mol/L and the relative standard deviation was 2.63%. Various factors affecting the electrocatalytic activity of cobalt hydroxide film were investigated.     

Cathodic electrochemiluminescence of luminol in aqueous solutions based on C-doped oxide covered titanium electrode

In the present work, a novel sensor for luminol electrochemiluminescence (ECL) was constructed on the base of a C-doped titanium oxide amorphous semiconductor electrode. The morphology, structural and electrochemical properties of the electrode was characterized by X-Ray diffraction, X-Ray photoelectron spectroscopy and electrochemical methods. The ECL behavior of luminol excited by hot electrons injected from C-doped oxide film-covered electrodes in aqueous medium has been investigated in B-R buffer solution (pH = 9) when linear sweep cyclic voltammetry (CV) was applied. Two ECL peaks were observed at −1.0 V (vs. Ag/AgCl, reduction process) and −0.75 V (vs. Ag/AgCl, oxidation process). The possible mechanism was discussed. The C-doped Ti oxide electrode shows excellent properties for sensitive determination of luminol with good reproducibility and stability. The linear response of luminol was in the range of 1 × 10⁻⁸ to 9 × 10⁻⁸ mol/L with the detection limit of 3 × 10⁻⁹ mol/L (S/N = 3). Since luminol is one of the most useful ECL probe, many bioactive compounds which can be labeled by luminol are able to be detected by using the proposed method.