Room temperature magnetoelectric coupling study in multiferroic Bi4NdTi3Fe0.7Ni0.3O15 prepared by a multicalcination procedure

Single-phase Bi₄NdTi₃Fe_0.7Ni_0.3O₁₅ polycrystalline samples were synthesized following a multicalcination procedure. The sample exhibited multiferroic property at room temperature, which was demonstrated by the ferroelectric (2P_r=8.52 μC/cm², 2E_c=89 kV/cm at applied electric field 110 kV/cm) and magnetic (2M_r=388 m emu/g, 2H_c=689 Oe at applied magnetic field 1.04 T) hysteresis loops. More importantly, magnetoelectric coupling effect is observed from measurements of electrical properties not only under small but also under large electric signal when an external magnetic field is applied. The present results suggest a new candidate for a room temperature multiferroic material with magnetoelectric coupling effect.     

Electrosynthesis and characterization of poly(2-[(E)-2-azulen-1-ylvinyl] thiophene) using polyazulene as model compound

Electrochemical polymerization of azulene and 2-[(E)-2-azulen-1-ylvinyl] thiophene has been studied in this work. Characterization of the formed films was done by cyclic voltammetry (CV), in situ UV-vis absorption spectroscopy and by scanning electron microscopy (SEM). Polymerization was performed by CV in a three-electrode electrochemical cell in 0.1 M tetrabutylammonium hexafluorophosphate-acetonitrile (TBAPF₆-ACN) within two different potential ranges. The redox behavior of the films was studied by CV in monomer-free TBAPF₆-ACN electrolyte solution. The electrochemical response from the anodic charging (p-doping) in the different films consisted of symmetric and well-resolved redox peaks. During electrochemical doping changes in the UV-vis spectra can be seen due to transformation of the films from the neutral into the doped form. Poly(2-[(E)-2-azulen-1-ylvinyl] thiophene), in particular shows a very broad absorbance spectrum starting at 300 nm extending to 900 nm. Morphologies of the electrosynthesized films were studied by SEM.     

Photo-electro catalytic oxidation of aromatic alcohols on visible light-absorbing nitrogen-doped TiO2

Visible light illumination of nitrogen-doped TiO₂ brings about the selective oxidation of benzyl and cinnamyl alcohol to the corresponding aldehydes. The photocatalyst was prepared by a sol-gel method and characterised mainly by XRD, UV-vis diffuse reflectance and Raman spectroscopy. The conditions limiting the observation of visible light photoactivity are the use of dry nitriles as nonaqueous solvents and aromatic alcohols as the substrates. No visible light oxidation takes place in an aqueous medium. The efficiency of benzyl and cinnamyl alcohol photo-oxidation in nitrile solvents follows the order: CH₃CN > CH₃CH₂CN > CH₃(CH₂)₂CN. Conversely, since alcohol photo-oxidation occurs with 100% selectivity on electrodes in O₂ saturated solutions at potentials close to E_fb or under open-circuit conditions, suspensions of the photocatalyst can be advantageously employed. The process involves a relatively weak adsorption of the alcohol substrates which, however, do not readily capture the photogenerated holes. On the basis of the electrochemical and photoluminescence data, it appears that the solvent (e.g. acetonitrile), in addition to O₂ has an active role in the reaction mechanism.     

Photoelectrochemical oxidation of salicylic acid and salicylaldehyde on titanium dioxide nanotube arrays

We report on the kinetics of photoelectrochemical oxidation of salicylic acid (SA) and salicylaldehyde (SH) on titanium dioxide nanotube arrays. The TiO₂ nanotubes were prepared by the electrochemical oxidation of titanium substrates in a nonaqueous electrolyte (DMSO/HF). Scanning electron microscopy (SEM) was employed to examine the morphology of the formed nanotubes. Linear voltammetry was used to study the electrochemical and photoelectrochemical behavior of the synthesized TiO₂ nanotube arrays. The photoelectrochemical oxidation of SA and SH on the TiO₂ nanotubes was monitored by in situ UV-vis spectroscopy, showing that the kinetics of the photoelectrochemical oxidation of SA and SH follows pseudo first-order and that the rate constant of SH oxidation is 1.5 times larger than that of SA degradation. Quantum chemical calculations based on the DFT method were performed on SA and SH to address the large difference in kinetics. The relatively higher E_LUMO − E_HOMO makes SA more stable and thus more difficult to be oxidized photoelectrochemically. The impact of temperature and initial concentrations on the kinetics of SA and SH photoelectrochemical degradation was also investigated in the present work.     

In situ UV-vis spectroelectrochemistry of poly(o-phenylenediamine-co-m-toluidine)

Results of in situ UV-vis spectroelectrochemical studies of the electropolymerization of o-phenylenediamine (OPD), m-toluidine (MT) and the copolymerization of OPD with MT are reported. Electropolymerization was performed in aqueous acidic medium at a constant potential of E_SCE = 1.0 V at an indium doped tin oxide (ITO) coated glass electrode. The course of homopolymerization was followed for MT and OPD solutions with various monomer concentrations. The spectral characteristics of the mixed solutions were studied at a constant concentration of MT and various concentrations of OPD in the comonomer feed. An absorption band at λ = 497 nm was assigned to the head-to-tail mixed dimer/oligomer resulting from the cross reaction between OPD and MT cation radicals. UV-vis spectra recorded during copolymerization show dependence of the growth of the band at λ = 497 nm on OPD concentration in the feed. At lower OPD feed concentration it appears as the major band in the corresponding spectra. The UV-vis spectra recorded for the copolymer films suggest the incorporation of both monomer units in the copolymer. The FT-IR spectra of the copolymers show the presence of phenazine type structures in the copolymer backbone.     

Preparation and reversible photo-crosslinking/photo-cleavage behavior of 4-methylcoumarin functionalized hyperbranched polyester

A novel hyperbranched polymer endcapped with 4-methylcoumarin group (MCTH40) was prepared via thiol-ene addition reaction of thiol-modified hyperbranched polyester (fully thioglycolic acetate of Boltorn™ H40, TAH40) with a vinyl monomer (7-(4-vinyl-benzyloxyl)-4-methylcoumarin, VBMC), and characterized with ¹H NMR and FT-IR spectroscopies. Its reversible photo-crosslinking/photo-cleavage behavior was evaluated based on the UV-vis spectroscopic analysis, and compared with the linear polymer, poly(7-(4-vinyl-benzyloxyl)-4-methylcoumarin (PVBMC)). The absorbance at 319 nm in the UV-vis spectrum gradually decreased under UVA irradiation (λ_max = 365 nm), and then rapidly recovered under UVC irradiation (λ_max = 254 nm). The fluorescence intensity of MCTH40 (λ_max = 469 nm) recovered to 85.2% of original level after photo-cleavage under UVC irradiation, higher than 83.5% of PVBMC (λ_max = 472 nm). The UV-vis analysis results indicated that MCTH40 performs more rapid photo-response than linear PVBMC under the same conditions. Furthermore, the average doses of UVA irradiation for the maximum degree of photo-crosslinking were 22.08 J cm⁻² for MCTH40 and 28.29 J cm⁻² for PVBMC. The average UVC doses of complete photo-cleavage were 9.44 J cm⁻² for MCTH40 and 9.58 J cm⁻² for PVBMC. The GPC analysis indicated that the average molecular weight and its PDI of MCTH40 showed a slight increase after three reversible cycles.     

Cation driven actuation for free standing PEDOT films prepared from propylene carbonate electrolytes containing TBACF3SO3

Free standing PEDOT [poly(3,4-ethylenedioxythiophene)] films (with surface conductivities of 200-400 S cm⁻¹) were generated in tetrabutylammonium trifluromethanesulfonate (TBACF₃SO₃) electrolytes by potentiostatic (E_P 1.05 V vs. Ag wire) electropolymerisation in propylene carbonate (at −27 °C) and methyl benzoate (at −4 °C). Films obtained in the TBACF₃SO₃ electrolytes showed a length increase of 2-3% during scans to negative potentials under isotonic (constant load 1.35 MPa) and stress of 0.3 MPa under isometric (constant length) conditions. Cation movement occurred due to immobilisation of CF₃SO₃⁻ anions during electropolymerisation. The system showed good stability and low creep during square wave electrochemical cycling in the potential range from 0.0 to 1.0 V. The surface morphology (SEM) of the PEDOT films showed that the polymer structure is dependent upon the solvent used during the polymerisation process.     

Synthesis, characterization and electrochemical properties of polybiselenophene

A novel electrically conducting polymer consisting of selenophene moiety, poly(biselenophene) (PBSE) was generated by chemical and electrochemical polymerization. This polymer gave lower bandgap energy (1.9 eV) than pristine polyselenophene (2.0 eV). The electrochemical and optical properties of PBSE was investigated by UV-Vis near infrared spectroscopy and electrochemistry. In situ electrochemical doping studies of PBSE showed the formation of polaron states at 1.4 and 0.8 eV. Through cyclic voltammetry, the polymer oxidation potential (E_pa) and reduction potential (E_pc) for p-doping process for PBSE were observed at 0.93 and 0.86 V, respectively, at a scan rate of 20 mV s⁻¹. Upon chemical doping using chemical reagents such as iodine and ferric chloride, a maximum conductivity of 0.1 S cm⁻¹ was achieved.     

Synthesis and transport properties in La2−xAxMo2O9−δ (A = Ca, Sr, Ba, K) series

The La_2−xA_xMo₂O_9−δ (A = Ca²⁺, Sr²⁺, Ba²⁺ and K⁺) series has been synthesised as nanocrystalline materials via a modification of the freeze-drying method. The resulting materials have been characterised by X-ray diffraction (XRD), thermal analysis (TG/DTA, DSC), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). The high-temperature β-polymorph is stabilised for dopant content x > 0.01. The nanocrystalline powders were used to obtain dense ceramic materials with optimised microstructure and relative density >95%. The overall conductivity determined by impedance spectroscopy depends on both the ionic radius and dopant content. The conductivity decreases slightly as the dopant content increases in addition a maximum conductivity value was found for Sr²⁺ substitution, which show an ionic radii slightly higher than La³⁺ (e.g. 0.08 S cm⁻¹ for La₂Mo₂O₉ and 0.06 S cm⁻¹ for La_1.9Sr_0.1Mo₂O_9−δ at 973 K). The creation of extrinsic vacancies upon substitution results in a wider stability range under reducing conditions and prevents amorphisation, although the stability is not enhanced significantly when compared to samples with higher tungsten content. These materials present high thermal expansion coefficients in the range of (13-16) × 10⁻⁶ K⁻¹ between room temperature and 753 K and (18-20) × 10⁻⁶ K⁻¹ above 823 K. The ionic transport numbers determined by a modified emf method remain above 0.98 under an oxygen partial pressure gradient of O₂/air and decreases substantially under wet 5% H₂-Ar/air when approaching to the degradation temperature above 973 K due to an increase of the electronic contribution to the overall conductivity.     

Direct electron-transfer and electrochemical catalysis of hemoglobin immobilized on mesoporous Al2O3

The direct electrochemistry of hemoglobin (Hb) has been achieved by immobilizing Hb on mesoporous Al₂O₃ (meso-Al₂O₃) film modified glassy carbon (GC) electrode. Meso-Al₂O₃ shows significant promotion to the direct electron-transfer of Hb, thus it exhibits a pair of well defined and quasi-reversible peaks with a formal potential of −0.345 V (vs. SCE). The electron-transfer rate constant (k_s) is estimated to be 3.17 s⁻¹. The immobilized Hb retains its biological activity well and shows high catalytic activity to the reduction of hydrogen peroxide (H₂O₂) and nitrite (NO₂⁻). Under the optimized experimental conditions, the catalytic currents are linear to the concentrations of H₂O₂ and NO₂⁻ in the ranges of 0.195-20.5 μM and 0.2-10 mM, respectively. The corresponding detection limits are 1.95 × 10⁻⁸ M and 3 × 10⁻⁵ M (S/N = 3). The resulting protein electrode has high thermal stability and good reproducibility due to the protection effect of meso-Al₂O₃. Ultraviolet visible (UV-vis) absorption spectra and reflection-absorption infrared (RAIR) spectra display that Hb keeps almost natural structure in the meso-Al₂O₃ film. The N₂ adsorption-desorption experiments show that the pore size of meso-Al₂O₃ is about 14.4 nm, suiting for the encapsulation of Hb (average size: 5.5 nm) well. Therefore, meso-Al₂O₃ is an alternative matrix for protein immobilization and biosensor preparation.     

Effects of annealing temperature on the photocatalytic activity of N-doped TiO2 thin films

The effects of annealing temperature on the photocatalytic activity of nitrogen-doped (N-doped) titanium oxide (TiO₂) thin films deposited on soda-lime-silica slide glass by radio frequency (RF) magnetron sputtering have been studied. Glancing incident X-ray diffraction (GIAXRD), Raman spectrum, scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV-vis spectra were utilized to characterize the N-doped TiO₂ thin films with and without annealing treatment. GIAXRD and Raman results show as-deposited N-doped TiO₂ thin films to be nearly amorphous and that the rutile and anatase phases coexisted when the N-doped TiO₂ thin films were annealed at 623 and 823 K for 1 h, respectively. SEM microstructure shows uniformly close packed and nearly round particles with a size of about 10 nm which are on the slide glass surface for TiO₂ thin films annealed at 623 K for 1 h. AFM image shows the lowest surface roughness for the N-doped TiO₂ thin films annealed at 623 K for 1 h. The N-doped TiO₂ thin films annealed at 623 K for 1 h exhibit the best photocatalytic activity, with a rate constant (k_a) of about 0.0034 h⁻¹.     

Electrochemical and ATR-FTIR study of dimethyl ether and methanol electro-oxidation on sputtered Pt electrode

DME has been considered to be a new alternative fuel for direct fuel cells. However, there is little knowledge about the electro-oxidation mechanism of the DME oxidation reaction (DOR). It is very important to know the intermediate adsorption species of the DOR on the Pt catalysts for verifying the DOR mechanism and developing more active catalysts in order to improve the performance of the direct DME fuel cell (DDMEFC). The electro-oxidation activity, coverage of the adsorption species, types of the intermediate adsorption species, and the fractional coverage of the linear-CO_ad (CO_L) of the DOR as the function of potential and scan rate were studied and compared with that of the methanol oxidation reaction (MOR).It was found that the coverage of the adsorption species (θ_ads) was ca. 90% for the DOR at 0.1 < E < 0.45 V on the Pt. The fractional coverage of CO_L formed in the DOR decreased with the decrease in the potential from 0.4 to 0.1 V. It was larger than 50% at 0.3 < E < 0.5 V. The CO_L would be the dominant adsorption species for the DOR. Except the CO_L, the intermediate adsorption species of the DOR were the bridge-CO_ad (CO_B), -COOH, -CHO, -HCOO- and -OCH₃.     

Factors influencing the structure of electrochemically prepared α-MnO2 and γ-MnO2 phases

The α- and γ-phases of MnO₂ prepared by electrolysis of MnSO₄ and M_xSO₄ (where M = Li⁺, Na⁺, K⁺, Rb⁺, Cs⁺ or Mg²⁺) in aqueous solutions at various pH and voltage E_v values under ambient conditions have been systematically studied. The structures of powdery MnO₂ produced are found to depend on the radius of the M^z+ counter cation in addition to the pH and E_v conditions. In order to achieve the α-phase for MnO₂ formation under neutral pH condition, the radius of counter cation must be equal to or greater than 1.41 Å, the size of the K⁺ cation. The relative concentration ratio of [MnO₄⁻]_transient/[Mn²⁺], which is related to the pH-E_v conditions, also affects the structure of MnO₂ produced with counter ions smaller than K⁺. For samples prepared in acidified solution with the counter ions of Li⁺, Na⁺ or Mg²⁺ at 2.2 V, the electrolysis products display the γ-MnO₂ phase while those prepared at 2.8 V electrolysis produce a mixture of γ-MnO₂ and α-MnO₂ phases. Single phase of α-MnO₂ is identified in the 5 V electrolysis products. Furthermore, the valence state of manganese was found to decrease as the applied voltage was reduced from 5.0 to 2.2 V. This implies that the lower [MnO₄⁻]_transient/[Mn²⁺] ratio or the less oxidative condition is responsible for the non-stoichiometric MnO₂ structure with oxygen deficiency.     

Study of phase composition of Zn-Ni alloy electrodeposited in acetate-chloride electrolyte at a temperature of 50 °C

The phase composition of Zn-Ni alloys electrodeposited under potentiodynamic and galvanostatic conditions in acetate-chloride plating solution with the ratio [Zn⁺²]/[Ni⁺²] = 1:12.8 at 50 °C has been investigated by the potentiodynamic stripping and XRD methods. It has been determined that two anodic peaks, which can be attributed to oxidation of the certain phases of Zn-Ni alloy emerged in potentiodynamic stripping curves (PDC) at E < 0 V and at E > 0 V. The Zn-Ni alloy phase that oxidized at E > 0 V was obtained by using cyclic voltammetry with the partial potentiodynamic stripping. This phase is ∼7 at.% Zn solid solution in Ni. The composition of Zn-Ni alloy phase that oxidized at E < 0 is ∼41.0 at.% Zn and ∼59.0 at.% Ni. The ratio of these phases in the alloys depends on the cathodic current density (i_c).     

Electrical conductivity and redox stability of La2Mo2−xWxO9 materials

A series of compounds La₂Mo_2−xW_xO₉ (x = 0-2) were synthesized using a freeze-dried precursor method at relatively low temperatures (673-823 K). These materials were characterised by thermogravimetric and differential thermal analysis (TG/DTA), differential scanning calorimetric (DSC), X-ray diffraction (XRD), and transmission electron microscopy (TEM) and dilatometric measurements. Oxygen stoichiometry was evaluated by coulometric titration and thermogravimetric analysis at 873-1273 K. The ionic and electronic conductivities of these materials were analysed by impedance spectroscopy and a Hebb-Wagner ion-blocking method under moderately reducing conditions. The presence of W⁶⁺ leads to an increase of the stability range (about 10⁻¹⁶ Pa for La₂Mo_0.5W_1.5O₉ at 1073 K) and prevents oxygen loss and amorphisation. Within the stability range, the electronic conductivity increases gradually as the temperature increases and as the oxygen partial pressure reduces. This indicates that the electronic transport is mainly n-type as a result of the oxygen-content decreasing in the molybdate lattice. Further reduction of the oxygen partial pressure gave rise to the decomposition of La₂Mo_2−xW_xO₉, leading to the formation of new phases with molybdenum in lower oxidation states, which further enhances the electronic conductivity. The results of the coulometric titration and the thermogravimetric studies under a dry 5% H₂/Ar flow suggest that tungsten doped lanthanum molybdate materials can be used as electrolyte only at low temperature and under moderate reducing conditions.     

Room temperature multiferroic properties of Ni-doped Aurivillus phase Bi5Ti3FeO15

Single-phase Aurivillius Bi₅Ti₃Fe_0.5Ni_0.5O₁₅ (BTFN) ceramics were synthesized by the solid-state reaction method. The substitution of Ni for half Fe ions does not introduce magnetic impurity phase but increases magnetic moment more than two orders. The ferroelectric and magnetic Curie temperatures are determined to be 1100 K and 726 K. The room-temperature multiferroic behavior of the BTFN ceramics were demonstrated by the ferroelectric (2P_r=8.5 μC/cm², 2E_c=74 kV/cm) and ferromagnetic (2M_r=27.86 m emu/g, 2H_c=553 Oe) measurements. The ferromagnetism can be ascribed to the aggregation of magnetic ions at the inner octahedra by Ni doping and the spin canting of magnetic-ion-based sublattices via the Dzyaloshinskii-Moriya interaction. The present work suggests the possibility of doped Bi₅Ti₃FeO₁₅ as a potential room-temperature multiferroic.     

Effect of BNBTKNN on the electrical properties of bismuth ferrite thin films

BiFeO₃/[0.93(Bi_0.50Na_0.50TiO₃)-0.05BaTiO₃-0.02K_0.50Na_0.50NbO₃] (BFO/BNBTKNN) bilayered thin films were fabricated on Pt/TiO₂/SiO₂/Si substrates without any buffer layers by a combined sol-gel and radio frequency sputtering route. Effect of BNBTKNN on electrical properties of BFO/BNBTKNN thin films was investigated. A higher phase purity and a denser microstructure are induced for the BFO/BNBTKNN bilayered thin film by using the bottom BNBTKNN layer, resulting in its lower leakage current density. Moreover, the enhancement in dielectric behavior is also demonstrated for such a bilayer, where a high dielectric constant and a low dielectric loss are obtained. The BFO/BNBTKNN bilayered thin film has an improved multiferroic behavior: 2P_r ∼ 76.8 μC/cm², 2E_c ∼ 378.1 kV/cm, 2M_s ∼ 52.6 emu/cm³, and 2H_c ∼ 453.6 Oe, together with a low fatigue rate up to ∼1 × 10⁹ switching cycles.     

Investigation of ternary system Pb(Sn,Ti)O3-Pb(Mg1/3Nb2/3)O3 with morphotropic phase boundary compositions

(1 − x)Pb(Sn_1−yTi_y)O₃-xPb(Mg_1/3Nb_2/3)O₃ (x = 0.1-0.4, y = 0.45-0.65) ternary system was prepared using two-step columbite precursor method. Phase structure of the synthesized ceramics was studied by using X-ray powder diffraction and the morphotropic phase boundary (MPB) curve of the ternary system was confirmed. The isothermal map of Curie temperature (T_C) in the phase diagram was obtained based on the dielectric-temperature measurements. The coercive field E_C and internal bias field E_i were found to increase with increasing PT content, while decrease with increasing PMN content. The optimum properties were achieved in the MPB composition 0.8Pb(Sn_0.45Ti_0.55)O₃-0.2Pb(Mg_1/3Nb_2/3)O₃, with dielectric permittivity ?_r, piezoelectric coefficient d₃₃, planar electromechanical coupling k_p, mechanical quality factor Q_m and T_C of being on the order of 3040, 530pC/N, 55.5%, 320 and 190 °C, respectively, exhibiting potential usage for high power application.     

Characteristics of solubilization and encapsulation of fullerene C60 in non-ionic Triton X-100 micelles

The solubilization and encapsulation of monomeric C₆₀ in Triton X-100 micelles were investigated. Characteristic hydrophobic interactions of the type π-π and CH-π between the Triton X-100 micelle and C₆₀ resulted in stable aqueous dispersions of C₆₀ in the micellar medium, as evidenced from UV-vis, fluorescence emission and micro-Raman spectroscopy. Cyclic voltammetry of C₆₀ encapsulated Triton X-100 in aqueous 5 mM LiClO₄ solution revealed a quasi-reversible one-electron reduction peak with E_1/2 = −0.61 V and a reversible reduction peak at E_1/2 = −1.11 V vs. Ag/AgCl reference electrode at a scan rate of 10 mV s⁻¹, a redox behaviour drifting substantially from that of pure C₆₀. An onset concentration of ∼0.025 mM for C₆₀ aggregation in the micellar core was substantiated from the characteristic absorption spectral broadening and quenching of pyrene fluorescence. The molar solubilization capacity of C₆₀ in aqueous Triton X-100 micellar solution was estimated spectrophotometrically to be 0.22.     

Low temperature synthesis and dielectric, ferroelectric and piezoelectric study of microwave sintered BaTiO3 ceramics

Barium titanate (BaTiO₃/BT) ferroelectric system was synthesized in single perovskite phase at low temperature by using powders derived from modified solid state reaction (MSSR) and sintered by microwave (MW) processing routes. Conventional calcination temperature was optimized at 900 °C for 4 h. MW sintering of BT samples was carried out at 1100 °C for 30 min to get dense (98% density) ceramics. Room temperature (RT) dielectric constant (?_r) and dielectric loss (tan δ) at 1 kHz frequency of MW sintered BT samples was found to be ∼2500 and 0.03, respectively. Saturated polarization vs. electric field (P-E) loops with remnant polarization (P_r) ∼6 μC/cm² and coercive field (E_c) ∼1.45 kV/cm confirmed the ferroelectric nature of MW sintered BT samples. Piezoelectric coefficient from strain vs. electric field (S-E) loops study was found to be 335 pm/V.