Novel PEO-based solid composite polymer electrolytes with inorganic–organic hybrid polyphosphazene microspheres as fillers

Novel solid-state composite polymer electrolytes based on poly (ethylene oxide) (PEO) by using LiClO₄ as doping salts and inorganic–organic hybrid poly (cyclotriphosphazene-co-4,4′-sulfonyldiphenol) (PZS) microspheres as fillers were prepared. Electrochemical and thermal properties of PEO-based polymer electrolytes incorporated with PZS microspheres were studied. Differential scanning calorimetry (DSC) results showed there was a decrease in the glass transition temperature of the electrolytes and the crystallinity of the samples in the presence of the fillers. Maximum ionic conductivity values of 1.2 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.5 × 10⁻⁴ S cm⁻¹ at 80° were obtained and lithium ion transference number was 0.29. Compared with traditional ceramic fillers such as SiO₂, the addition of PZS microspheres increased the ionic conductivity of the electrolytes slightly and led to remarkable enhancement in the lithium ion transference number.     

Synthesis and electrochemical characterization of PEO-based polymer electrolytes with room temperature ionic liquids

New gel polymer electrolytes containing 1-butyl-4-methylpyridinium bis(trifluoromethanesulfonyl)imide (BMPyTFSI) ionic liquid are prepared by solution casting method. Thermal and electrochemical properties have been determined for these gel polymer electrolytes. The addition of BMPyTFSI to the P(EO)₂₀LiTFSI electrolyte results in an increase of the ionic conductivity, and at high BMPyTFSI concentration (BMPy⁺/Li⁺ = 1.0), the ionic conductivity reaches the value of 6.9 × 10⁻⁴ S/cm at 40 °C. The lithium ion transference numbers obtained from polarization measurements at 40 °C were found to decrease as the amount of BMPyTFSI increased. However, the lithium ionic conductivity increased with the content of BMPyTFSI. The electrochemical stability and interfacial stability for these gel polymer electrolytes were significantly improved due to the incorporation of BMPyTFSI.     

Synthesis and electrochemical properties of lithium methacrylate-based self-doped gel polymer electrolytes

In this study, a strategy for synthesizing lithium methacrylate (LiMA)-based self-doped gel polymer electrolytes was described and the electrochemical properties were investigated by impedance spectroscopy and linear sweep voltammetry. LiMA was found to dissolve in ethylene carbonate (EC)/diethyl carbonate (DEC) (3/7, v/v) solvent after complexing with boron trifluoride (BF₃). This was achieved by lowering the ionic interactions between the methacrylic anion and lithium cation. As a result, gel polymer electrolytes consisting of BF₃-LiMA complexes and poly(ethylene glycol) diacrylate were successfully synthesized by radical polymerization in an EC/DEC liquid electrolyte. The FT-IR and AC impedance measurements revealed that the incorporation of BF₃ into the gel polymer electrolytes increases the solubility of LiMA and the ionic conductivity by enhancing the ion disassociations. Despite the self-doped nature of the LiMA salt, an ionic conductivity value of 3.0 × 10⁻⁵ S cm⁻¹ was achieved at 25 °C in the gel polymer electrolyte with 49 wt% of polymer content. Furthermore, linear sweep voltammetry measurements showed that the electrochemical stability of the gel polymer electrolyte was around 5.0 V at 25 °C.     

High ionic transfer of a hyperbranched-network gel copolymer electrolyte for potential electric vehicle (EV) application

Hyperbranched network-based gel copolymer electrolytes are synthesized by in situ free radical polymerization. This research is separated into two parts: the first is an investigation of modified bismaleimide oligomer (MBMI) as a free volume additive, and the second investigates the salt concentration effect on high power application. A polymer electrolyte with MBMI additive provided more free volume space, and the ionic conductivity of gel copolymer electrolytes was measured as a function of the salt concentration of lithium hexafluorophosphate (LiPF₆). The highest ionic conductivity and the lowest activation energy of hyperbranched-network gel copolymer electrolytes were determined to be 7.72 × 10⁻³ S/cm at 23 °C and 5.41 kJ/mol, respectively. Furthermore, the MBMI additive and the optimal concentration of lithium salt increased the free space for carrier ions and contributed to increasing capacity and working voltage at a high rate discharge (8C). The reliability and cycling ability of lithium polymer batteries are as good as lithium ion batteries for potential electric vehicle (EV) application.     

Effect of zwitterionic salt on the electrochemical properties of a solid polymer electrolyte with high temperature stability for lithium ion batteries

In this study, we prepare a kind of solid polymer electrolyte (SPE) based on N-ethyl-N′-methyl imidazolium tetrafluoroborate (EMIBF₄), LiBF₄ and poly(vinylidene difluoride-co-hexafluoropropylene) [P(VdF-HFP)] copolymer. The resultant SPE displays high thermal stability above 300 °C and high room temperature ionic conductivity near to 10⁻³ S cm⁻¹. Its electrochemical properties are improved with incorporation of a zwitterionic salt 1-(1-methyl-3-imidazolium)propane-3-sulfonate (MIm3S). When the SPE contains 1.0 wt% of the MIm3S, it has a high ionic conductivity of 1.57 × 10⁻³ S cm⁻¹ at room temperature, the maximum lithium ions transference number of 0.36 and the minimum apparent activation energy for ions transportation of 30.9 kJ mol⁻¹. The charge-discharge performance of a Li₄Ti₅O₁₂/SPE/LiCoO₂ cell indicates the potential application of the as-prepared SPE in lithium ion batteries.     

Preparation and electrochemical behaviors of polymeric composite electrolytes containing mesoporous silicate fillers

In the present study, poly(ethylene oxide) (PEO)-based polymeric composite electrolytes (PCEs) had been prepared by using a different content of mesoporous silicate MCM-41, in order to examine the filler addition effect on the microstructural and electrochemical properties. The interactions between MCM-41 and PEO matrix were studied by XRD, DSC, and SEM techniques. The electrochemical properties of the PCEs, such as ionic conductivity, its temperature dependence, and lithium transference number were investigated. MCM-41 could maintain the pore structure effectively, resulting in nanocomposites that were homogeneously complexed with the PEO chains. The PCEs with 8 wt.% MCM-41 showed the smallest crystallinity, 30.4%. Accordingly, those PCEs showed the highest ion conductivity, 1.2 × 10⁻⁴ S/cm, a two-order-of-magnitude higher value than that of the pristine PEO-LiClO₄. This might have reflected decreased crystallinity and improved ion transport. Furthermore, those PCEs showed an increased Li ion transference number of ∼0.5. In conclusion, the filler addition could enhance the ionic conductivity and increase the Li ion transference number at the same time.     

Composite alkaline polymer electrolytes and its application to nickel-metal hydride batteries

In order to enhance the ionic conductivity of polyethylene oxide (PEO)-KOH based alkaline polymer electrolytes, three types of nano-powders, i.e., TiO₂, β-Al₂O₃ and SiO₂ were added to PEO-KOH complex, respectively, and the corresponding composite alkaline polymer electrolytes were prepared. The experimental results showed that the prepared polymer electrolytes exhibited higher ionic conductivities at room temperature, typically 10⁻³ S cm⁻¹ as measured by ac impedance method, and good electrochemical stability. The electrochemical stability window of ca. 1.6 V was determined by cyclic voltammetry with stainless steel blocking electrodes. The influence of the film composition such as KOH, H₂O and nano-additives on ion conductivity was investigated and explained. The temperature dependence of conductivity was also determined. In addition, polyvinyl alcohol (PVA)-sodium carboxymethyl cellulose (CMC)-KOH alkaline polymer electrolytes were obtained using solvent casting method. The properties of the polymer electrolytes were characterized by ac impedance, cyclic voltammetry and differential thermal analysis methods. The ionic conductivity of the prepared PVA-CMC-KOH-H₂O electrolytes can reach the order of 10⁻² S cm⁻¹. The effect of CMC addition on the alkaline polymer electrolytes was also explained. The experimental results demonstrated that the PVA-CMC-KOH-H₂O polymer electrolyte could be used in Ni/MH battery.     

Preparation of poly(acrylonitrile-butyl acrylate) gel electrolyte for lithium-ion batteries

Poly(acrylonitrile-butyl acrylate) gel polymer electrolyte was prepared for lithium ion batteries. The preparation started with synthesis of poly(acrylonitrile-butyl acrylate) by radical emulsion polymerization, followed by phase inversion to produce microporous membrane. Then, the microporous gel polymer electrolytes (MGPEs) was prepared with the microporous membrane and LiPF₆ in ethylene carbonate/diethyl carbonate. The dry microporous membrane showed a fracture strength as high as 18.98 MPa. As-prepared gel polymer electrolytes presented ionic conductivity in excess of 3.0 × 10⁻³ S cm⁻¹ at ambient temperature and a decomposition voltage over 6.6 V. The results showed that the as-prepared gel polymer electrolytes were promising materials for Li-ion batteries.     

Simple introduction of anion trapping site to polymer electrolytes through dehydrocoupling or hydroboration reaction using 9-borabicyclo[3.3.1]nonane

Organoboron-based anion trapping polymer electrolytes were synthesized through hydroboration or dehydrocoupling reaction between poly(propylene oxide) (PPO) oligomer (M_n = 400, 1200, 2000 and 4000) and 9-borabicyclo[3.3.1]nonane (9-BBN). Obtained oligomers were added various lithium salts (LiN(CF₃SO₂)₂, LiSO₃CF₃, LiCO₂CF₃ or LiBr) to analyze the ionic conductivity and lithium ion transference number (tLi⁺). The ionic conductivity of the oligomer in the presence of LiN(CF₃SO₂)₂ showed higher ionic conductivity than other systems, however, the tLi⁺ was less than 0.3. When LiSO₃CF₃ or LiCO₂CF₃, was added high tLi⁺ over 0.6 was obtained. Such difference in tLi⁺ can be explained by HSAB principle. Since boron is a hard acid, soft (CF₃SO₂)₂N⁻ anion can not be trapped effectively. High ionic conductivity of 1.3 × 10⁻⁶ S cm⁻¹ and high tLi⁺ of 0.73 was obtained when PPO chain length was 2000. These values of facilely prepared polymer electrolytes are comparable to those of the PPOs having covalently bonded salt moieties on the chain ends.     

Effect of Al2O3 nanoparticles on the electrochemical characteristics of P(VDF-HFP)-based polymer electrolyte

Alumina (Al₂O₃) nanoparticles have been used as fillers in the preparation of poly(vinylidenefluoride-co-hexafluorpropylene) (P(VDF-HFP))-based porous polymer electrolyte. The degree of crystallization of polymer film filled with Al₂O₃ nanoparticles decreases with increase of the mass fraction of Al₂O₃ nanoparticles and the amorphous phases of polymer film expand accordingly. The Al₂O₃ nanoparticles play the role of solid plasticizer for polymer matrix. Nevertheless that excessive Al₂O₃ nanoparticles existing in polymer matrix leads to micro-phase separation between polymer matrix and fillers. As a result, both ionic conductivity and lithium ions transference number reduces whereas the activation energy for ions transport increases. When the polymer film is filled with 10% of the mass fraction of Al₂O₃ nanoparticles, polymer electrolyte possesses the ionic conductivity up to 1.95 × 10⁻³ S cm⁻¹ and the lithium ions transference number to 0.73 while the activation energy for ions transport of them falls to 5.6 kJ mol⁻¹. Effect of Al₂O₃ on the electrochemical properties of polymer electrolyte has been investigated in this paper. Analysis of FTIR spectra shows that there is the interaction between Al₂O₃ nanoparticles and polymer chains.     

Composite polymer electrolyte incorporating WO3 nanofillers with enhanced performance for dendrite-free solid-state lithium battery

All solid-state lithium batteries (ASS-LBs) with polymer-based solid electrolytes are a prospective contender for the next-generation batteries because of their high energy density, flexibility, and safety. Among all-polymer electrolytes, PEO-based solid polymer electrolytes received huge consideration as they can dissolve various Li salts. However, the development of an ideal PEO-based solid polymer electrolyte is hindered by its insufficient tensile strength and lower ionic conductivity due to its semi-crystalline and soft chain structure. In order to lower the crystallization and improve the performance of PEO-based solid polymer electrolyte, tungsten trioxide (WO₃) nanofillers were introduced into PEO matrix. Herein, a PEO₂₀/LiTFSI/x-WO₃ (PELI-xW) (x = 0%, 2.5%, 5%, 10%) solid composite polymer electrolyte was prepared by the tape casting method. The solid composite polymer electrolyte containing 5 wt% WO₃ nanofillers achieved the highest ionic conductivity of 7.4 × 10^-4 S cm^-1 at 60 °C. It also confirms a higher Li-ion transference number of 0.42, good electrochemical stability of 4.3V, and higher tensile strength than a PEO/LiTFSI (PELI-0W) fillers-free electrolyte. Meanwhile, the LiFePO₄│PELI-xW│Li ASS-LBs demonstrated high performance and cyclability. Based on these findings, it can be considered a feasible strategy for the construction of efficient and flexible PEO-based solid polymer electrolytes for next-generation solid-state batteries.     

Li NMR spectroscopy and ion conduction mechanism of composite gel polymer electrolyte: A comparative study with variation of salt and plasticizer with filler

Microporous composite gel polymer electrolyte (CGPE) has been prepared by incorporating the home-made silica aerogel (SAG) particles into the poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) copolymer/LiClO₄ matrix. The ionic transport behavior of the electrolyte is studied with various experimental techniques such as AC impedance, X-ray diffraction (XRD), infrared (IR) spectra, nuclear magnetic resonance (NMR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA), etc. The results reveal that the SAG particles are well dispersed in the electrolytes and incorporate with the other components of the CGPEs. The solid-state ⁷Li NMR study has confirmed the interactions of lithium ion with SAG, polymer and plasticizers, causing to form the microporous structure and reduce the glass transition temperature and crystallinity, resulting in an increase in ionic conductivity of the CGPE. The best ionic conductivity (1.04 × 10⁻² S/cm at room temperature) is obtained from the composite polymer electrolyte containing 4 wt% of SAG, which is approximately four times higher than the ionic conductivity of the electrolyte without the filler.     

Effect of the addition of hydrophobic clay on the electrochemical property of polyacrylonitrile/LiClO4 polymer electrolytes for lithium battery

In this study, an organoclay, ALA-MMT, was prepared by the ionic exchange reaction of montmorillonite (MMT) with 12-aminododecanoic acid (ALA). ALA-MMT was then used as a filler to prepare a series of composite polymer electrolytes based on polyacrylonitrile (PAN) and LiClO₄. The effect of the addition of ALA-MMT on the properties of the composite polymer electrolytes (CPEs) was investigated by XRD, FT-IR, DSC, tensile strength, AC impedance, and cyclic voltammetry measurements. It was found that the ALA-MMT particles were well dispersed in the CPEs. Owing to the incorporation of ALA-MMT, a higher fraction of the free anions was obtained, indicating that the lithium salt dissolved in the PAN matrix more effectively for the CPE than in the PAN/LiClO₄ polymer electrolyte. Moreover, the glass-transition temperature was reduced, benefiting the ion transport. The best ionic conductivity at room temperature was obtained from the CPE with 7 wt% of the modified clay and 0.6 M LiClO₄ per PAN repeat unit (CPE-7) and was more than seven times higher than that from the corresponding PAN/LiClO₄ polymer electrolyte (CPE-0). The mechanical property and the cation transference number, t₊, of CPE-7 are largely increased compared to that of CPE-0. Besides, the CPEs were electrochemically stabilized up to 4.75 V and the corresponding cell exhibited excellent electrochemical stability and cyclability over the potential range between 0 V and 4.0 V vs. Li/Li⁺.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Effects of the surface treatment of the Al2O3 filler on the lithium electrode/solid polymer electrolyte interface properties

The lithium deposition-dissolution process in solid polymer electrolytes containing Al₂O₃ filler treated under different conditions has been investigated comparing with the ionic conduction behavior of the electrolyte. The composite electrolytes were prepared from poly(ethylene oxide) (PEO), LiBF₄ and α-Al₂O₃ filler by using a dry process, where the surface of α-Al₂O₃ was beforehand modified by a wet process. The exchange current densities, i₀, of the lithium electrode process in P(EO)₂₀LiBF₄ with and without Al₂O₃ filler were determined by a micro-polarization method. The temperature dependence of i₀ provided similar values for activation energy, ca. 25 and 70 kJ mol⁻¹ in both temperature regions above and below 60 °C, respectively. The effect of the surface treatment of the filler on the lithium electrode process gave a different tendency from that on the ionic conductivity. The Al₂O₃ surface treated by alkali solution enhanced the electrode process to the largest extent among the fillers used here, while it led to rather poor cycling stability in voltammetry. The enhanced reaction rate at the lithium electrode/solid polymer electrolyte interface has probably resulted in the improved ion dissociation by the surface groups of the Al₂O₃ filler.     

Role of amorphous boundary layer in enhancing ionic conductivity of lithium-lanthanum-titanate electrolyte

The low ionic conductivity is a bottleneck of the inorganic solid state electrolyte used for lithium ion battery. In ceramic electrolytes, grain boundary usually dominates the total conductivity. In order to improve the grain boundary effect, an amorphous silica layer is introduced into grain boundary of ceramic electrolytes based on lithium-lanthanum-titanate, as evidenced by electron microscopy. The results showed that the total ionic conductivity could be to be enhanced over 1 × 10⁻⁴ S/cm at room temperature. The reasons can be attributed to removing the anisotropy of outer-shell of grains, supplement of lithium ions in various sites in grain boundary and close bindings among grains by the amorphous boundary layer among grains.     

The conductivity and characterization of the plasticized polymer electrolyte based on the P(AN-co-GMA-IDA) copolymer with chelating group (II): The effect of free ion in the plasticized polymer electrolyte

A new gel-type polymer electrolyte (GPE) was made by the copolymerizing acrylonitrile (AN) and (2-methylacrylic acid 3-(bis-carboxymethylamino)-2-hydroxy-propyl ester) (GMA-IDA). The copolymer mixed with a plasticizer—propylene carbonate (PC) and lithium salt to form GPE. The lithium salts are LiCF₃SO₃, LiBr and LiClO₄. FT-IR spectra show that the lithium ion in the LiClO₄ system has the strongest interaction with the group based on the plasticized polymer. FT-IR spectra also indicate that CF₃SO₃⁻ prefers producing anion-cation association. Moreover, the ¹³C solid state NMR spectra for the carbons attached to the PC of GPE exhibited different level of chemical shift (158.5 ppm) when the different lithium salts were added to the electrolyte. The results of differential scanning calorimeter (DSC) also indicate that the LiClO₄ system has more free lithium ions; therefore, it has the maximum conductivity. In this study, the highest conductivity 2.98 × 10⁻³ S cm⁻¹ exists in AG2/PC = 20/80 wt.% system which contain 3 mmole (g-polymer)⁻¹ LiClO₄. Additionally, the polymer electrolytes, which contain GMA-IDA have better interfacial resistance stability with lithium electrode.     

Gel electrolytes based on lithium modified silica nano-particles

In this work lithium modified silica (Li-SiO₂) nano-particles were synthesized and used as a single ion lithium conductor source in gel electrolytes. It was found that Li-SiO₂ exhibited good compatibility with DMSO, DMA/EC (a mixture of N,N-dimethyl acetamide and ethylene carbonate) and the ionic liquid, N-methyl-N-propyl pyrrolidinium bis(trifluoromethylsulfonyl) amide ([C₃mpyr][NTf₂]). Several gel electrolytes based on Li-SiO₂ were obtained. These gel electrolytes were investigated by DSC, solid state NMR, conductivity measurements and cyclic voltammetry. Conductivities as high as 10⁻³ S/cm at room temperature were observed in these nano-particle gel electrolytes. The results of electrochemical tests showed that some of these materials were promising for using as lithium conductive electrolytes in electrochemical devices, with high lithium cycling efficiency evident.     

A foaming process to prepare porous polymer membrane for lithium ion batteries

A foaming process was used to prepare porous polymer membranes (PPMs) based on poly(vinylidene diflouride-co-hexafluoropropylene) copolymer for lithium ion batteries. In this simple process, urea, the foaming agent, was decomposed into gases and was removed at an elevated temperature to get the porous structure within the polymer matrix. When the weight ratio of urea to P(VDF-HFP) is 5:6, the PPM presents the highest porosity, 70.2%, and the prepared gelled polymer electrolyte shows an ionic conductivity up to 1.43 × 10⁻³ S cm⁻¹ at room temperature. This provides another way to prepare gelled polymer electrolytes easily for application in rechargeable lithium batteries.     

Characterisation of [(1−x)PMMA-xPVdF] polymer blend electrolyte with Li ion

The possible use of polymeric materials in thin-film solid electrolytes for battery systems, fuel cells, sensors and other electrochemical applications has stimulated worldwide interest in metal salt solvating macromolecules. Polymer electrolyte membranes comprising of poly(methyl methacrylate) (PMMA), poly(vinylidene fluoride) (PVdF) and lithium perchlorate are prepared using a solvent casting technique. Polymer blends have been characterised by FTIR and XRD studies to determine the molecular environment for the conducting ions. The role of interaction between polymer hosts on conductivity is discussed using the results of ac impedance studies. The ionic conductivity is presented as a function of temperature and PVdF content. Room temperature conductivity of 3.14×10⁻⁵ S cm⁻¹ has been obtained for the [0.25PMMA/0.75PVdF]-LiClO₄ polymer complex.