Hydrotreating of gas oil on SBA-15 supported NiMo catalysts

The siliceous and the metal substituted (B or Al)-SBA-15 molecular sieves were used as a support for NiMo hydrotreating catalysts (12 wt.% Mo and 2.4 wt.% Ni). The supports were characterized by X-ray diffraction (XRD), scanning electron microscopy and N₂ adsorption–desorption isotherms. The SBA-15 supported NiMo catalysts in oxide state were characterized by BET surface area analysis and XRD. The sulfided NiMo/SBA-15 catalysts were examined by DRIFT of CO adsorption and TPD of NH₃. The HDN and HDS activities with bitumen derived light gas oil at industrial conditions showed that Al substituted SBA-15 (Al-SBA-15) is the best among the supports studied for NiMo catalyst. A series of NiMo catalysts containing 7–22 wt.% Mo with Ni/Mo weight ratio of 0.2 was prepared using Al-SBA-15 support and characterized by BET surface area analysis, XRD and temperature programmed reduction and DRIFT spectroscopy of adsorbed CO. The DRIFT spectra of adsorbed CO showed the presence of both unpromoted and Ni promoted MoS₂ sites in all the catalysts, and maximum “NiMoS” sites concentration with 17 wt.% of Mo loading. The HDN and HDS activities of NiMo/Al-SBA-15 catalysts were studied using light gas oil at temperature, pressure and WHSV of 370 °C, 1300 psig and 4.5 h⁻¹, respectively. The NiMo/Al-SBA-15 catalyst with 17 wt.% Mo and 3.4 wt.% of Ni is found to be the best catalyst. The HDN and HDS activities of this catalyst are comparable with the conventional Al₂O₃ supported NiMo catalyst in real feed at industrial conditions.     

Highly dispersed NiW/γ-Al2O3 catalyst prepared by hydrothermal deposition method

This article describes a novel hydrothermal deposition method for preparing highly dispersed NiW/γ-Al₂O₃ catalysts and demonstrates its advantages over the conventional impregnation method. Via the hydrothermal precipitation reactions between sodium tungstate and hydrochloric acid and between nickel nitrate and urea, respectively, the active species W and Ni were deposited on γ-Al₂O₃. In the hydrothermal deposition of WO₃, a surfactant hexadecyltrimethyl ammonium bromide (CTAB) was used to prevent the aggregation of WO₃. The characterization results obtained by means of X-ray photoelectron spectroscopy (XPS), N₂ adsorption and high-resolution transmission electron microscopy (HRTEM) measurements showed that compared with the catalyst prepared by the conventional impregnation method, the catalyst with the same metal contents prepared by the hydrothermal deposition had much higher W and Ni dispersion, higher specific surface area, larger pore volume, the significantly decreased slab length and slightly increased stacking degree of sulfided W species, leading to the significantly enhanced dibenzothiophene (DBT) hydrodesulfurization (HDS) activity. The DBT HDS assessment results also revealed that the catalyst containing 17.7 wt% WO₃ and 2.4 wt% NiO prepared by the hydrothermal deposition method had the similar DBT HDS activity as a commercial NiW/γ-Al₂O₃ catalyst containing 23 wt% WO₃ and 2.6 wt% NiO, resulting in the greatly decreased amount of active metals for achieving the same HDS activity.     

Deep HDS over NiMo/Zr-SBA-15 catalysts with varying MoO3 loading

In the present work, with the aim of searching for new, highly effective catalysts for deep HDS, a series of NiMo catalysts with different MoO₃ loadings (6–30 wt.%) was prepared using SBA-15 material covered with ZrO₂-monolayer as a support. Prepared catalysts were characterized by N₂ physisorption, small- and wide-angle XRD, UV–vis diffuse reflectance spectroscopy, temperature-programmed reduction, SEM-EDX and HRTEM, and their catalytic activity was evaluated in the 4,6-dimethyldibenzothiophene hydrodesulfurization (HDS). It was observed that ZrO₂ incorporation on the SBA-15 surface improves the dispersion of the Ni-promoted oxidic and sulfided Mo species, which were found to be highly dispersed, up to 18 wt.% of MoO₃ loading. Further increase in metal charge resulted in the formation of MoO₃ crystalline phase and an increase in the stacking degree of the MoS₂ particles. All NiMo catalysts supported on ZrO₂-modified SBA-15 material showed high activity in HDS of 4,6-DMDBT. The best catalyst having 18 wt.% MoO₃ and 4.5 wt.% NiO was almost twice more active than the reference NiMo/γ-Al₂O₃ catalyst. High activity of NiMo/Zr-SBA-15 catalysts and its evolution with metal loading was related to the morphological characteristics of the MoS₂ active phase determined by HRTEM.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

Effect of Re loading on the structure, activity and selectivity of Re/C catalysts in hydrodenitrogenation and hydrodesulphurisation of gas oil

A series of Re-containing catalysts supported on activated carbon, with Re loading between 0.74 and 11.44 wt.% Re₂O₇, was prepared by wet impregnation and tested in the simultaneous hydrodesulphurisation (HDS) and hydrodenitrogenation (HDN) of a commercial gas oil. Textural analysis, XRD, X-ray photoelectron spectroscopy (XPS) and surface acidity techniques were used for physicochemical characterisation of the catalysts. Increase in the Re concentration resulted in a rise in the HDS and HDN activity due to the formation of a monolayer structure of Re and the higher surface acidity. At Re concentrations >2.47 wt.% Re₂O₇ (0.076 Re atoms nm⁻²) the reduction in the catalytic activity was related to the loss in specific surface area (BET) due to reduction in the microporosity of the carbon support. The magnitude of the catalytic effect was different for HDS and HDN, and depended strongly on the Re content and reaction temperature. The apparent activation energies were about 116–156 kJ mol⁻¹ for HDS and 24–30 kJ mol⁻¹ for HDN. This led to a marked increase in the HDN/HDS selectivity with decreasing temperature (values >3 at 325 °C), due to the large differences in the apparent activation energies of HDS and HDN found for all catalysts. A gradual increase in the HDN/HDS selectivity with increased Re loading was also found and related to the observed increase of catalyst acidity. The results are compared with those obtained for a series of Re/γ-Al₂O₃ catalysts.     

A series of NiMo/Al2O3 catalysts containing boron and phosphorus: Part II. Hydrodenitrogenation and hydrodesulfurization using heavy gas oil derived from Athabasca bitumen

The hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activity of a series of NiMo/Al₂O₃ catalyst containing boron (B) and phosphorus (P) were tested in a trickle bed reactor using heavy gas oil derived from Athabasca bitumen. Detailed characterization of these catalysts is given in Part I of this paper. Addition of B and P caused the formation of extremely strong acid sites on the catalyst and enhanced its HDN activity. The total (TN), basic (BN) and non-basic nitrogen (NBN) conversions increased from 61.9 to 78.0 wt.%, from 78.9 to 93.0 wt.% and from 52.8 to 70.0 wt.%, respectively, with the increase in B concentration from 0 to 1.7 wt.% to NiMo/Al₂O₃ catalyst. Similarly, TN, BN and NBN conversions increased from 61.9 to 78.4 wt.%, from 78.9 to 91.0 wt.%, and from 52.8 to 71.6 wt.% with the addition of 2.7 wt.% P. Though the addition of B and P to NiMo/Al₂O₃ catalyst did not show any significant effect on S conversion, the HDN and HDS activities of the catalyst containing 1.7 wt.% B and the one containing 2.7 wt.% P are comparable to those of a commercial catalyst. The activity over extended period indicated that catalysts L and K were more stable (lower deactivation rate) in terms of nitrogen removal activity than catalyst B (reference catalyst). On the other hand, the stability for sulfur removal was comparable with catalyst B. Selected catalysts after use were characterized using BET surface area, TPR, TPD and SEM techniques which were correlated further with their activities.     

Synthesis,characterization and hydrotreating performance of supported tungsten phosphide catalysts

Supported tungsten phosphide catalysts were prepared by temperature-programmed reduction of their precursors (supported phospho-tungstate catalysts) in H₂ and characterized by X-ray diffraction (XRD), BET, temperature-programmed desorption of ammonia (NH₃-TPD) and X-ray photoelectron spectroscopy (XPS). The reduction-phosphiding processes of the precursors were investigated by thermogravimetry and differential thermal analysis (TG-DTA) and the suitable phosphiding temperatures were defined. The hydrodesulfurization (HDS) and hydrodenitrogenation (HDN) activities of the catalysts were tested by using thiophene, pyridine, dibenzothiophene, carbazole and diesel oil as the feedstock. The TiO₂, ?-Al₂O₃ supports and the Ni, Co promoters could remarkably increase and stabilize active W species on the catalyst surface. A suitable amount of Ni (3%–5%), Co (5%–7%) and V (1%–3%) could increase dispersivity of the W species and the BET surface area of the WP/?-Al₂O₃ catalyst. The WP/?-Al₂O₃ catalyst possesses much higher thiophene HDS and carbazole HDN activities and the WP/TiO₂ catalyst has much higher dibenzothiophene (DBT) HDS and pyridine HDN activities. The Ni, Co and V can obviously promote the HDS activity and inhibit the HDN activity of the WP/?-Al₂O₃ catalyst. The G-Ni5 catalyst possesses a much higher diesel oil HDS activity than the sulphided industrial NiW/?-Al₂O₃ catalyst. In general, a support or promoter in the WP/?-Al₂O₃ catalyst which can increase the amount and dispersivity of the active W species can promote its HDS and HDN activities.     

Tailoring of alumina surfaces as supports for NiMo sulfide catalysts in the ultra deep hydrodesulfurization of gas oil: case study of TiO2-coated alumina prepared by chemical vapor deposition technique

The present paper gives a detailed review of the different studies under investigation in our laboratory concerning the use of TiO₂ and TiO₂–Al₂O₃ composites prepared by chemical vapor deposition (CVD) as support for sulfide catalysts in the HDS of dibenzothiophene (DBT) derivatives. The supports investigated here are: TiO₂ (from Degussa, 50 m²/g), Al₂O₃ (Nikki, 186 m²/g) and TiO₂–Al₂O₃ supports prepared by CVD of TiCl₄ on alumina. Using several characterization techniques, we have demonstrated that the support composite presents a high dispersion of TiO₂ over γ-Al₂O₃ without forming precipitates up to ca. 11 wt.% loading. Moreover, the textural properties of the support composite are comparable to those of alumina. XPS investigations of Mo and NiMo catalysts supported on the different carriers show that Mo-oxide species exhibit a higher degree of sulfidation on the surface of TiO₂ and TiO₂–Al₂O₃ than on alumina. The HDS tests of 4,6-DMDBT under mild operating conditions (573 K, 3 MPa) show that sulfide catalysts supported on the composite support (ca. 11 wt.%) are more active than those supported on to TiO₂ or Al₂O₃. This higher HDS catalytic activity is attributed to the promotion of the hydrodesulfurization pathway, whereby the pre-hydrogenation of one of the aromatic rings adjacent to the thiophenic one may reduce the steric hindrance caused by the two methyl groups adjacent to the sulfur atom during the C–S bond cleavage.     

Performance and characterization of Ru/Al2O3 and Ru/SiO2 catalysts modified with Mn for Fischer–Tropsch synthesis

Mn effect and characterization on γ-Al₂O₃-, -Al₂O₃- and SiO₂-supported Ru catalysts were investigated for Fischer–Tropsch synthesis under pressurized conditions. In the slurry phase Fischer–Tropsch reaction, γ-Al₂O₃ catalysts showed higher performance on CO conversion and C₅⁺ selectivity than -Al₂O₃ and SiO₂ catalysts. Moreover, Ru/Mn/γ-Al₂O₃ exhibited high resistance to catalyst deactivation and other catalysts were deactivated during the reaction. From characterization results on XRD, TPR, TEM, XPS and pore distribution, Ru particles were clearly observed over the catalysts, and γ-Al₂O₃ catalysts showed a moderate pore and particle size such as 8 nm, where -Al₂O₃ and SiO₂ showed highly dispersed ruthenium particles. The addition of Mn to γ-Al₂O₃ enhanced the removal of chloride from RuCl₃, which can lead to the formation of metallic Ru with moderate particle size, which would be an active site for Fischer–Tropsch reaction. Concomitantly, manganese chloride is formed. These schemes can be assigned to the stable nature of Ru/Mn/γ-Al₂O₃ catalyst.     

Study of Ag/La0.6Sr0.4MnO3 catalysts for complete oxidation of methanol and ethanol at low concentrations

Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure were prepared by using a citric acid sol–gel method, and their catalytic performance for complete oxidation of methanol and ethanol was evaluated and compared with that of the γ-Al₂O₃-supported catalysts, Ag/γ-Al₂O₃, Pt/γ-Al₂O₃, and Pd/γ-Al₂O₃. The results showed that the Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure displayed the activity significantly higher than that of the supported precious metal catalysts, 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ in the temperature range of 370–573 K. Over a 6%Ag/20%La_0.6Sr_0.4MnO₃/γ-Al₂O₃ catalyst, the T₉₅ temperature for methanol oxidation can be as low as 413 K. Even at such low reaction temperature, there were little HCHO and CO detected in the reaction exit-gas. However, for the 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ catalysts, the HCHO content in the reaction exit-gas reached 200 and 630 ppm at their T₉₅ temperatures. Over a 6%Ag/La_0.6Sr_0.4MnO₃ catalyst, the T₉₅ temperature for ethanol oxidation can be as low as 453 K, with a corresponding content of CH₃CHO in the exit-gas at 782 ppm; when ethanol oxidation is performed at 493 K, the content of acetaldehyde in the exit-gas can be below 1 ppm. Characterization of the catalysts by X-ray diffraction (XRD), TEM, XPS, laser Raman spectra (LRS), hydrogen temperature-programmed reduction (H₂-TPR) and oxygen temperature-programmed desorption (O₂-TPD) methods revealed that both the surface and the bulk phase of the perovskite La_0.6Sr_0.4MnO₃ played important roles in the catalytic oxidation of the alcohols, and that γ-Al₂O₃ as the bottom carrier could be beneficial in creating a large surface area of catalyst. Moreover, a small amount of Ag⁺ doped onto the surface of La_0.6Sr_0.4MnO₃ was able to partially occupy the positions of La³⁺ and Sr²⁺ due to their similar ionic radii, and thus, became stabilized by the perovskite lattice, which would be in favor of preventing the aggregation of the Ag species on the surface and enhancing the stability of the catalyst. On the other hand, modification of the Ag⁺ to the surface of La_0.6Sr_0.4MnO₃ resulted in an increase in relative content of the surface O₂²⁻/O⁻ species highly reactive toward the alcohols and aldehydes as well as CO. Besides, solution of low-valence metal oxides SrO and Ag₂O with proper amounts in the lattice of the trivalent metal perovskite-type oxide LaMnO₃ would also lead to an increase in the content of the reducible Mnⁿ⁺ and the formation of anionic vacancies, which would be favorable for the adsorption-activation of oxygen on the functioning catalyst and the transport of the lattice and surface oxygen species. All these factors would contribute to the pronounced improvement of the catalyst performance.     

制备条件对NiMo/γ-Al2O3催化剂上萘加氢生成四氢萘的影响

采用等体积浸渍法制备加氢催化剂NiMo/γ-Al₂O₃,在悬浮床上考察不同的制备条件下NiMo/γ-Al₂O₃对萘加氢生成四氢萘的影响。结果表明,催化剂的制备条件对加氢活性有显著的影响,NiMo/γ-Al₂O₃催化剂的最佳制备条件为共浸渍法负载金属组分Ni和Mo,在500 ℃的温度下焙烧4 h。此条件下制备的催化剂上四氢萘的选择性高达95.2%。     

HDS and HDN activity of molybdenum and nickel–molybdenum catalysts supported on alumina–titania carriers

Alumina–titania supports containing 5–50 wt.% of TiO₂ were prepared by coprecipitation method using inorganic precursors (sodium aluminate and titanium chloride). DTA-TGA, XRD, SEM, TPD_NH3, and IR spectroscopy were used to characterise these materials. The study shows that the promoting effect of nickel on the HDS activity of molybdenum catalysts supported on Al₂O₃TiO₂ is significantly lower than that for molybdenum catalyst supported on Al₂O₃, and depends on the TiO₂ content. The SEM results show that in the case of rich Al support (20 wt.% of TiO₂) molybdenum was aggregated on the external surface of the catalyst, whereas it was uniformly dispersed on the external surface of alumina. Results also show that molybdenum is preferably supported on aluminum oxide. Application of Al₂O₃TiO₂ oxides enhances the HDN activity of nickel–molybdenum catalysts. The highest HDN efficiency was obtained for the NiMo/Al₂O₃TiO₂ catalyst containing 50 wt.% of TiO₂. HDN activity was found to depend on protonic acidity and anatase content.     

Hydrodesulfurization of thiophene, dibenzothiophene and gas oil on various Co---Mo/TiO2-Al2O3 catalysts

Evaluation of Co---Mo catalysts prepared on various TiO₂-Al₂O₃ supports has been made for thiophene under atmospheric pressure, dibenzothiophene under high pressure and gasoil in a classical pilot plant. Comparison of activities indicates DBT as more representative of a real feedstock and the Co---Mo/TiO₂ (50%)-Al₂O₃ (50%) catalyst appears more active than the Co---Mo/Al₂O₃ sample toward HDS, HDN and hydrodearomatization.     

Synthesis of bulk and alumina-supported γ-Mo2N catalysts by a single-step complex decomposition method

A single-step complex decomposition method for the synthesis of bulk and alumina-supported γ-Mo₂N catalysts is described. The complex precursor (HMT)₂(NH₄)₄Mo₇O₂₄·2H₂O (HMT: hexamethylenetetramine) is converted to γ-Mo₂N under a flow of Ar in a temperature range of 823–1023 K. Furthermore, decomposition of the precursor in a NH₃ flow forms γ-Mo₂N in a temperature range of 723–923 K. Compared with direct decomposition of the precursor in Ar, the reaction in NH₃ shows obvious advantages that the nitride forms at a lower temperature. In addition, alumina-supported γ-Mo₂N catalysts with different nitride loadings can be prepared from the alumina-supported complex precursor in the Ar or NH₃ flow. The resultant catalysts exhibit good dibenzothiophene HDS activities, which are similar to the γ-Mo₂N/γ-Al₂O₃ prepared by traditional TPR method. The catalyst prepared by decomposition in an Ar flow exhibits highest activity. It proves that such a single-step complex decomposition method possesses the potential to be a general route for the preparation of molybdenum nitride catalysts.     

Fischer–Tropsch synthesis on monolithic catalysts of different materials

Monolithic structures made of cordierite, γ-Al₂O₃ and steel have been prepared as catalysts and tested for Fischer–Tropsch activity. The monoliths made of cordierite and steel were washcoated with a 20 wt.% Co–1 wt.% Re/γ-Al₂O₃ Fischer–Tropsch catalyst whereas the γ-Al₂O₃ monoliths were made by direct impregnation with an aqueous solution of the Co and Re salts resulting in a loading of 12 wt.% Co and 0.5 wt.% Re. The activity and selectivity of the different monoliths were compared with the corresponding powder catalysts.

Higher washcoat loadings resulted in decreased C₅₊ selectivity and olefin/paraffin ratios due to increased transport limitations. The impregnated γ-Al₂O₃ monoliths also showed similar C₅₊ selectivities as powder catalysts of small particle size (38–53 μm). Lower activities were observed with the steel monoliths probably due to experimental problems.     

Origin of transient species present on the surface of a PdO/γ-Al2O3 catalyst during the methane combustion reaction

Operando DRIFTS was applied to the study of the evolution of surface species formed on a Pd (2 wt.%)/γ-Al₂O₃ catalyst in various conditions. No differences were observed as a function of the initial oxidation state of palladium. Formates/carbonates species were identified at low temperature (<400 °C) and disappeared when CO₂ production started. These species come from the Pd-catalyzed interaction of CO with the alumina support, while CO₂ induces hydrogenocarbonates formation at low temperature (<300 °C). Their presence does not explain the inhibiting effect of CO₂ observed in CCM on Pd/γ-Al₂O₃ catalysts.     

Synthesis and characterization of P-modified mesoporous CoMo/HMS–Ti catalysts

A hexagonal mesoporous siliceous material with a wormhole framework structure incorporating Ti (HMS-Ti; Si/Ti atomic ratio of 40) was modified with variable amounts of phosphorous and used as support for CoMo phases. The catalysts were prepared by successive impregnation, with Mo being introduced first. The supports and catalysts were characterized by N₂ adsorption–desorption, High-resolution transmission electron microscopy, X-ray diffraction, FT-IR study of the framework vibrations, DRIFT spectra in the OH region, ¹H NMR, FT-IR spectra of adsorbed NO, micro-Raman spectroscopy and X-ray photoelectron spectroscopy. The catalysts were tested in the reaction of hydrodesulfurization (HDS) of dibenzothiophene (DBT) and their activity compared with that of a commercial P-containing CoMo/γ-Al₂O₃ catalyst. The physical and chemical characterization of the P-modified HMS–Ti substrates shows that the presence of P₂O₅ on the support surface does not change its mesoporous character, but modifies its surface properties. In addition, characterization data of the oxide catalysts show that phosphate favors the dispersion of the active phases and increases the population of octahedral Co²⁺ ions associated to Mo species. As a result, HDS activity was strongly enhanced upon P-loading, which reached a maximum of 0.64 wt%. This catalyst is 3.7 times more active than the commercial one and 2.4 times more active than its P-free counterpart. The highest activity of this catalyst was explained in terms of the specific electronic properties of its active phases and the largest Mo surface exposure on the support.     

The effect of CeO2 structure on the activity of supported Pd catalysts used for methane steam reforming

Palladium (Pd) supported on CeO₂-promoted γ-Al₂O₃ with various CeO₂ (ceria) crystallinities, were used as catalysts in the methane steam reforming reaction. X-ray diffraction (XRD) analysis, FTIR spectroscopy of adsorbed CO, and X-ray photoelectron spectroscopy (XPS) were employed to characterize the samples in terms of Pd and CeO₂ structure and dispersion on the γ-Al₂O₃ support. These results were correlated with the observed catalytic activity and deactivation process. Arrhenius plots at steady-state conditions are presented as a function of CeO₂ structure. Pd is present on the oxidized CeO₂-promoted catalysts as Pd⁰, Pd⁺ and Pd²⁺, at ratios strongly dependent on CeO₂ structure. XRD measurements indicated that Pd is well dispersed (particles <2 nm) on crystalline CeO₂ and is agglomerated as large clusters (particles in 10–20 nm range) on amorphous CeO₂. FTIR spectra of adsorbed CO revealed that after pre-treatment under H₂ or in the presence of amorphous CeO₂, partial encapsulation of Pd particles occurs. CeO₂ structure influences the CH₄ steam reforming reaction rates. Crystalline CeO₂ and dispersed Pd favor high reaction rates (low activation energy). The presence of CeO₂ as a promoter conferred high catalytic activity to the alumina-supported Pd catalysts. The catalytic activity is significantly lower on Pd/γ-Al₂O₃ or on amorphous (reduced) CeO₂/Al₂O₃ catalysts. The reaction rates are two orders of magnitude higher on Pd/CeO₂/γ-Al₂O₃ than on Pd/γ-Al₂O₃, which is attributed to a catalytic synergism between Pd and CeO₂. The low rates on the reduced Pd/CeO₂/Al₂O₃ catalysts can be correlated with the loss of Pd sites through encapsulation or particle agglomeration, a process found mostly irreversible after catalyst regeneration.     

Interactions NO—CO and O2—NO—CO on CuCo2O4/γ-Al2O3 and on γ-Al2O3- and CuCo2O4/γ-Al2O3-supported Pt, Rh and Pt—Rh catalysts, a transient response study

The interactions NO—CO and O₂—NO—CO have been studied onCuCo₂O₄γ-Al₂O₃ and on γ-Al₂O₃- and CuCo₂O₄γ-Al₂O₃-supported Pt, Rh and Pt—Rh catalysts. The deposition of noble metals (Pt, Rh and Pt—Rh) on CuCo₂O₄γ-Al₂O₃ instead of γ-Al₂O₃ is beneficial in: lowering the temperature at which maximum N₂O is formed and decreasing the maximum N₂O concentration attained; lowering the onset temperature of NO to N₂ reduction, and increasing the N₂ selectivity; preserving the activity towards NO to N₂ reduction on a higher level following the concentration step NO + COO₂+ NO + CO and changing the conditions from stoichiometric to oxidizing (50% excess of oxidants). The reason for this behaviour of the CuCo₂O₄γ-Al₂O₃-based noble metal catalysts is the formation (reversible) of a reduced surface layer on the CuCo₂O₄ supported spinel under the conditions of a stoichiometric NO + CO mixture.     

Maya crude hydrodemetallization and hydrodesulfurization catalysts: An effect of TiO2 incorporation in Al2O3

Hydrotreating of Maya heavy crude oil over high specific surface area CoMo/TiO₂–Al₂O₃ oxide supported catalysts was studied in an integral reactor close to industrial practice. Activity studies were carried out with Maya crude hydrodesulfurization (HDS), hydrodemetallization (HDM), hydrodenitrogenation (HDN), and hydrodeasphaltenization (HDAs) reactions. The effect of support composition, the method of TiO₂ incorporation, and the catalyst deactivation are examined. Supported catalysts are characterized by BET specific surface area (SSA), pore volume (PV), pore size distribution (PSD), and atomic absorption. It has been found that sulfided catalysts showed a wide range of activity variation with TiO₂ incorporation into the alumina, which confirmed that molybdenum sulfided active phases strongly depend on the nature of support. The pore diameter and nature of the active site for HDS, HDM, HDN, and HDAs account for the influence of the large reactant molecules restricted diffusion into the pore, and/or the decrease in the number of active sites due to the MoS₂ phases buried with time-on-stream. The textural properties and hysteresis loop area of supported and spent catalysts indicated that catalysts were deactivated at the pore mouth due to the metal and carbon depositions. The atomic absorption results agreed well regarding the textural properties of spent catalysts. Thus, incorporation of TiO₂ with γ-Al₂O₃ alters the nature of active metal interaction with support, which may facilitate the dispersion of active phases on the support surface. Therefore, the TiO₂ counterpart plays a promoting role to HDS activity due to the favorable morphology of MoS₂ phases and metal support interaction.