木薯淀粉与醋酸乙烯酯的接枝共聚研究

以木薯淀粉为接枝骨架,过硫酸铵为引发剂,醋酸乙烯酯(VAC)为接枝单体,进行接枝共聚。研究了单体浓度、引发剂浓度、反应时间、反应温度对淀粉醋酸乙烯酯接枝共聚反应的影响,并通过正交试验,确定了最佳反应条件。结果表明:当单体浓度为1.1mol/L、引发剂浓度为18.3×10-3mol/L,反应温度60℃、反应时间3~3.5h时,可得到高的单体转化率、接枝效率和接枝率,并用SrectrumOne红外光谱对接枝物的化学结构进行了分析。     

氧化还原引发木薯淀粉与丙烯酰胺接枝共聚的研究

以木薯淀粉和丙烯酰胺为原料,采用氧化还原引发体系合成淀粉-丙烯酰胺接枝共聚物,研究了温度、引发剂浓度、单体浓度以及反应时间对聚合反应的影响。结果表明：采用氧化还原引发剂可以使聚合反应低温快速进行。实验最佳条件：反应温度为40℃,引发剂浓度为4mmol／L,单体质量浓度为85mg／mL,反应时间为3h。     

影响单分散聚苯乙烯微球粒径因素的研究

利用正交实验设计的数学方法进行设计，考察不同因素对微球粒径的影响，以制备出不同粒径的聚苯乙烯微球，主要考察的因素有：温度，引发剂浓度，单体浓度以及离子浓度，同时对其交互作用进行了研究，结果表明，4种因素对粒径影响的排序为：温度，引发剂浓度，离子浓度，单体浓度，其中引发剂浓度与单体浓度的交互作用明显。     

微悬浮聚合法合成聚醋酸乙烯酯的动力学研究

采用微悬浮法合成聚醋酸乙烯酯,对其聚合反应的动力学进行了研究。考察了引发剂浓度、乳化剂浓度、单体浓度以及温度对聚合反应速率的影响。结果表明,聚合反应速率对引发剂浓度、乳化剂浓度和单体浓度的反应级数分别为0．45,0．28,1．90,单体浓度对聚合反应速率的影响最大,反应体系的表观活化能为105．96 kJ/mol。     

低分子量的聚丙烯酸钠的合成研究

以H2O2-NaHSO3为引发剂,在超声波辅助下引发丙烯酸单体聚合,研究了单体浓度、引发剂用量、反应温度等对单体转化率和聚丙烯酸钠分子量的影响。结果表明:控制单体浓度30%、引发剂用量4.0%、反应温度60℃,可制得聚丙烯酸钠的相对分子量在2000～3000之间。     

EA与壳聚糖的接枝聚合反应

以过硫酸钾为引发剂,研究了丙烯酸乙酯（ Ｅ Ａ）与壳聚糖的接枝聚合反应。并对反应时间、温度、引发剂浓度和单体浓度对接枝聚合反应的影响进行了研究。     

EA与壳聚糖的接枝聚合反应

以过硫酸钾为引发剂,研究了丙烯酸乙酯与壳聚糖 接枝聚合反应。并对反应时间,温度,引发剂浓度和单体浓度对接枝聚合反应的影响进行了研究。     

PVC片材表面的光接枝亲水化处理

采用光接枝聚合方法对商品化PVC片材进行了表面亲水化处理。以二苯甲酮作引发剂 ,丙烯酸为接枝单体研究了反应过程中单体浓度、引发剂浓度、反应时间对亲水化效果的影响。衰减全反射红外光谱 (ATR FTIR)分析发现 ,在 15 5 5cm-1处出现COO-的特征峰 ,证明丙烯酸已经接枝到材料表面。随着反应时间的延长 ,接触角持续下降 ,3 0s以后趋于恒定 ,最低可达 3 3°。较低单体浓度下 ,均聚反应较弱 ,材料的亲水性要好于高单体浓度时的情况。同样 ,较低引发剂浓度时 ,引发剂的自屏蔽效应弱 ,有利于接枝反应 ,接触角要比高引发剂浓度条件下小     

碳纤维原丝用聚丙烯腈的聚合反应条件

采用水相沉淀聚合法,以过硫酸铵为引发剂,制备了丙烯腈-丙烯酸甲酯-甲叉丁二酸三元共聚物,研究了聚合温度、单体浓度、引发剂浓度对聚丙烯腈共聚物相对分子质量和单体转化率的影响。结果表明:当反应温度为58℃,反应时间为2.5 h,单体质量分数为25%,引发剂质量分数为1.5%时,聚合物的黏均分子质量达3.8×105,单体转化率为79%。     

反相微乳液聚合引发剂对聚丙烯酰胺分子质量影响的研究

分别以三种引发剂体系为引发剂,从引发机理出发,通过正交实验研究了丙烯酰胺反相微乳液聚合中引发剂种类、引发剂浓度、反应温度、单体浓度等对聚丙烯酰胺(PAM)相对分子质量的影响。结果表明,引发剂种类对水溶性PAM相对分子质量有显著的影响;过硫酸铵-亚硫酸氢钠和偶氮二异丁腈复合引发体系是合成高相对分子质量PAM的有效引发体系。该引发体系在反应温度为40℃,氧化还原引发剂与偶氮的质量比为1∶4,单体浓度为20%,引发剂浓度为0.3%,pH为9的最佳条件下合成的PAM相对分子量为1.44×107。     

Monomer Effects on Emulsion Polymerization with ASR as the Surfactant

In this paper, alkali soluble resin (ASR) was evaluated as a surfactant in the emulsion polymerizations of methyl methacrylate (MMA), ethyl methacrylate (EMA), and butyl methacrylate (BMA). It was found that the number of particles formed was proportional to the hydrophilicity of monomer and the concentration of initiator. Kinetic analysis indicated that the monomer concentration within the latex particle influences the average number of radicals per latex particle. The increase of monomer concentration within the particle enhances radical desorption from the particle and reduces the average number of radicals per particle. Experimental results show that the grafting reaction of ASR is proportional to the concentration of initiator or ASR. But the hydrophilicity of monomer is the major factor which influences the grafting reaction. This phenomenon is due to the fact that particle nucleation is different between the hydrophilic and hydrophobic monomer.     

Characterization of polystyrene latexes

Polystyrene latexes were prepared by emulsion polymerization. Styrene was used as monomer, potassium persulfate was the reaction initiator and sodium hydrogen carbonate was used as buffer. Surfactant may or may not be used. Three types of surfactant, ie sodium dodecylbenzene sulfonate (anionic), Triton X‐100 and Vulcastab LW (nonionic), and hexadecyltrimethyl ammonium bromide (cationic), were used. The prepared latexes were characterized according to concentration, density, pH, ionic strength, particle size, particle size distribution and surface charge. For prepared latexes with anionic surfactant, the effects of temperature, initiator concentration, surfactant concentration and amount of monomer on the latex size were investigated. Scanning electron microscopy was used as a tool for latex characterization. The results show that by increasing temperature, initiator and emulsifier concentration, the latex diameter decreases. However, size increases by increasing the amount of monomer. A potentiometric titration technique was employed for determination of surface charge. It was found that for all latexes, surface charge densities are in the same range. © 2000 Society of Chemical Industry     

聚甲基丙烯酸氨基乙酯的合成及染色性能

以白油为分散介质,偶氮二异丁腈为引发剂,甲基丙烯酸氨基乙酯为单体,采用反相悬浮聚合法合成聚甲基丙烯酸氨基乙酯(PTAM),研究了引发剂用量、反应温度、反应时间、单体浓度对PTAM特性粘数的影响。将PTAM与聚丙烯腈(PAN)共混纺丝制得共混纤维,用酸性染料染色,考察其上染率。结果表明:合成PTAM的最佳工艺条件为引发剂质量分数0.05%,单体质量分数60%,反应温度65℃,反应时间2h,所得PTAM的特性粘数为690mL/g。染色实验结果表明,PTAM质量分数为7%时,PAN共混纤维的上染率达88%。     

聚合条件对P（AN-co—IA）分子质量分布影响的研究

采用凝胶色谱（GPC）法测定了丙烯腈与衣康酸共聚物P（AN—co—IA）的重均分子质量和数均分子质量,并通过已知聚丙烯腈的重均分子质量数据和数均分子质量数据对所测的分子质量进行校正,进一步计算得到共聚物的多分散系数。同时研究了引发剂用量、单体浓度、聚合温度、聚合时间对P（AN—co—IA）分子质量分布的影响。研究结果表明,P（AN-co-IA）分子质量分布随引发剂用量的增大、聚合单体浓度的增加而变宽,与聚合反应温度、聚合反应时间无明显的变化趋势。     

Dispersion Polymerization of Styrene by Initiation Within Monomer Phase with Lauroyl Peroxide

Dispersion polymerization kinetics of styrene was investigated in this study. A monomer phase soluble initiator, namely lauroyl peroxide, and a water phase soluble emulsifier, namely sodium dodecyl sulfate, were used. the polymerizations were carried out in a magnetic drive, sealed, cylindrical polymerization reactor, in nitrogen atmosphere. Two different fatty alcohols, cetyl and lauryl alcohols, were tried as particle size increasing agents. the effects of initiator, emulsifier concentrations, monomer/water ratio, and the weight ratio of particle size increasing agent to emulsifier on the total monomer conversion, average size, and size distribution of the large latex particles were studied. the agglomeration conditions were tested by changing the polymerization temperature, initiator, and emulsifier concentrations. the results indicated that the polymerization rate and the average size of the latex increased with increasing emulsifier concentration. the average size of the latex was also increased with increasing initiator concentration. the use of cetyl alcohol in the presence of emulsifier resulted in an appreciable increase in the polymerization rate and in the average size of the latex. the effect of fatty alcohols on the polymerization rate in the dispersion polymerization system was completely different than that in the swollen emulsion polymerization. the agglomeration of the large latex particles was increased with decreasing emulsifier and increasing initiator concentrations.     

羟乙基纤维素添加在醋丙乳液中做保护胶体的初步研究

采用羟乙基纤维素为保护胶体制备了醋丙乳液,探讨了乳液聚合过程中共聚单体配比、保护胶体用量、温度和引发剂等因素对乳液聚合的影响,多方面考察乳液的性能.结果表明：羟乙基纤维素为保护胶体可制备稳定的醋丙乳液,该乳液具有优良的电解质性能.     

Studies on the grafting of methyl methacrylate onto polyacrylonitrile

Grafting of methyl methacrylate onto polyacrylonitrile was carried out using benzoyl peroxide as initiator and dimethylformamide as solvent. The occurrence of grafting was confirmed by IR spectroscopy and SEM analysis. Effects of various parameters such as reaction time, reaction temperature, initiator concentration, and monomer concentration on rate of polymerization, percentage grafting, and grafting efficiency were studied. The graft copolymers were found to have the similar thermal and structural properties like virgin polyacrylonitrile. Decreasing extent of swelling was observed for the polymers of higher percentage graft in polar solvents. © 1993 John Wiley & Sons, Inc.     

Factorial experimental design approach in semicontinuous emulsion polymerization of methyl methacrylate to study the effect of process variables

This article describes the effect of various process variables in the semicontinuous emulsion polymerization of methyl methacrylate. A series of poly(methyl methacrylate) (PMMA) emulsions were prepared using ammonium persulphate as initiator in absence and presence of Dowfax 2AI as surfactant. The effect of process variables such as initiator concentration, monomer concentration (solid content), surfactant concentration, reaction temperature, monomer feeding time, and holding time were systematically studied on monomer conversion, particle size, gel content, and molecular weight using a two‐level fractional factorial experimental method. Analysis of fractional factorial design revealed that surfactant concentration, monomer concentration, initiator concentration, and monomer feeding time affect all the properties. However, the surfactant concentration and the interaction effect of initiator and monomer feeding time are the key variables influencing the properties of PMMA latex. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Water‐soluble copolymers. II. Inverse emulsion terpolymerization of acrylamide,sodium acrylate,and acryloyloxyethyl trimethylammonium chloride

Inverse emulsion terpolymerization of acrylamide, sodium acrylate, and acryloyloxyethyl trimethylammonium chloride was investigated. Aqueous monomer solutions were emulsified in diesel oil with a blend of two surfactants (SPAN80 and TWEEN80) using 2,2′‐azobis(2‐amidinopropen)‐dihydrochloride as the initiator. The effects of temperature, initiator concentration, monomer concentration and composition, and emulsifier content on the polymerization conversion and the polymer intrinsic viscosity were examined. Polymer intrinsic viscosity increased with a decreasing concentration of initiator and an increasing concentration of monomer. The sizes of the latex particles of the terpolymer emulsions were observed with a scanning electron microscope, and the structure of the terpolymer was identified by FTIR spectroscopy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1381–1385, 2006     

St-BA-BVP无皂共聚物阳离子乳胶粒大小及形态研究

合成阳离子共单体 1-丁基 ,4 -乙烯吡啶溴化铵 ( BVP) ,并以偶氮二异丁基咪盐酸 ( A IBA)作引发剂 ,制备苯乙烯 /丙烯酸丁酯 ( St/ BA )共聚物乳液 ,通过 TEM研究改变 BVP的浓度、St/ BA主单体的配比及单体加料方式对 P( St/ BA / BV P)乳胶粒大小形态的影响 ,结果表明批量法和单体全滴加法制备的乳胶粒形状规则、分布均匀、半连续法制备的乳胶粒子呈多分散分布 ,粒径相差很大 ,且 P( St) / P( BA)得到的乳胶粒呈明显的核壳结构。