Ultra-wideband bandpass filter using hybrid quasi-lumped elements and defected ground structure

A compact planar microstrip ultra-wideband (UWB) bandpass filter is presented. The proposed UWB filter is realised by cascading a highpass filter (HPF) and a lowpass filter (LPF). Additional U-slot defected ground structure is adopted to improve the attenuation performance in the stop band. The HPF consists of inter-digital capacitors and a short-circuited stub. The LPF achieved by a hybrid microstrip and four backside slots on the ground plane is equivalent to a typical 9-pole stepped-impedance LPF. Combining these two structures, a new UWB bandpass filter is fabricated and measured. Measured results show that the proposed bandpass filter has a wide bandwidth from 3.1 to 11 GHz, and insertion loss is less than 1.2 dB over the most central passband. It also achieves a wide stop band with 20 dB attenuation up to 20 GHz.     

Small Ultra-Wideband (UWB) Bandpass Filter With Notched Band

A compact ultra-wideband (UWB) bandpass filter (BPF) with notched band has been proposed and implemented in this letter. H-shaped slot is studied and adopted to tighten the coupling of inter-digital capacitor in order to improve the BPF's performance. Three pairs of tapered defected ground structures (DGS) are formed to assign their transmission zeros towards the out of band signal, thereby suppressing the spurious passband. Combining these two structures we obtain a small sized UWB BPF. Meander line slot is developed to reject the undesired wireless local-area network (WLAN) radio signals. An experimental UWB filter with notched band was fabricated with 35% less length as compared to an embedded open-circuited stub. The measured BPF insertion loss is less than 1.0 dB throughout the pass band of 2.8 to 10.8 GHz, the variation of group delay less than 0.20 ns in this band except for the notched band, and a wide stopband bandwidth with 20 dB attenuation up to at least 20.0 GHz.     

一种新型超宽带带通滤波器的设计

针对超宽带(UWB)系统易受无线网络信号干扰及传统的超宽带带通滤波器阻带较窄,不能有效抑制谐波的问题,提出了一种新型的UWB带通滤波器,该滤波器由两级交指梳状耦合谐振器级联组成,通过增加耦合指的个数来实现陷波特性,然后在两个交指谐振器的中间添加一个槽线锥形谐振器,使该滤波器具有抑制高次谐波特性,达到拓宽高阻带的效果,同时由于槽线谐振器的加入,陷波频段的抑制电平进一步提高.实验结果证明,所设计的滤波器既能保证3.1～10.6 GHz频段内的插入损耗小于3 dB,陷波频段为5.7～5.8 GHz,陷波频段的抑制电平高达-43 dB,同时又能拓宽高频阻带.     

Ultra Wideband Bandpass Filter Using Embedded Stepped Impedance Resonators on Multilayer Liquid Crystal Polymer Substrate

This letter proposes an ultra wideband (UWB) bandpass filter (BPF) based on embedded stepped impedance resonators (SIRs). In this study, broad side coupled patches and high impedance microstrip lines are adopted as quasi-lumped elements for realizing the coupling between adjacent SIRs, which are used to suppress stopband harmonic response. An eight-pole UWB BPF is developed from lump-element bandpass prototype and verified by full-wave simulation. The proposed filter is fabricated using multilayer liquid crystal polymer (LCP) process and measured using vector network analyzer. Good agreement between simulated and measured response is observed. The measurement results show that the fabricated filter has a low insertion loss of 0.18 dB at center frequency 6.05 GHz, an ultra wide fractional bandwidth of 127.3% and excellent stopband rejection level higher than 32.01 dB from 10.9 to 18.0 GHz.      

Compact UWB Bandpass Filter Using Stub-Loaded Multiple-Mode Resonator

A compact microstrip-line ultra-wideband (UWB) bandpass filter (BPF) using the proposed stub-loaded multiple-mode resonator (MMR) is presented. This MMR is formed by loading three open-ended stubs in shunt to a simple stepped-impedance resonator in center and two symmetrical locations, respectively. By properly adjusting the lengths of these stubs, the first four resonant modes of this MMR can be evenly allocated within the 3.1-to-10.6 GHz UWB band while the fifth resonant frequency is raised above 15.0GHz. It results in the formulation of a novel UWB BPF with compact-size and widened upper-stopband by incorporating this MMR with two interdigital parallel-coupled feed lines. Simulated and measured results are found in good agreement with each other, showing improved UWB bandpass behaviors with the insertion loss lower than 0.8dB, return loss higher than 14.3dB, and maximum group delay variation less than 0.64ns in the realized UWB passband     

Compact ultra-wideband bandpass filter using broadside coupled hairpin structures on multilayer liquid crystal polymer substrate

A novel ultra-wideband (UWB) bandpass filter (BPF) using a broadside- coupled hairpin structure and multilayer organic liquid crystal polymer (LCP) technology is presented. To suppress stopband harmonic response, folded stepped impedance structures were adopted as hairpin resonators in the design. The proposed filter has been investigated numerically and experimentally. Multilayer LCP technology was used to implement designed UWB BPF. Good agreement between simulated and measured results of the proposed filter was observed. They show that the fabricated UWB BPF has a good performance, including a small insertion loss, a flat group delay with a variation within 0.1 ns in most of its passband, a wide stopband from 11.0 20.0 GHz with a high rejection level up to 20.0 dB, and a very compact size of 9.8 x 7.5 mm (0.36 lg x 0.27lg, where lg is the guided wavelength of 50 V microstrip line at 6.85 GHz).     

Miniaturized dual-band bandpass filter with good frequency selectivity using SIR and DGS

A miniaturized dual-band bandpass filter (BPF) using stepped impedance resonator (SIR) and defected ground structure (DGS) is presented. In order to get two desired passbands, two different transmission paths and source–load cross coupling have been implemented. One path is the SIR, and the other is the DGS. Meanwhile, it is easy to obtain good frequency selectivity by introducing several transmission zeros. The coupling scheme and current distributions are applied to demonstrate the flexible design approach. A dual-band BPF is designed, simulated, and fabricated to demonstrate the performance of the proposed dual-band filter. The measured results show that the fabricated dual-band BPF has two passbands centered at 2.41 and 3.52 GHz with the fractional bandwidth of 5.8 and 7.7%, respectively. The measured insertion loss is about 2 dB and 2.2 dB at the lower and upper passbands. The measured results show good agreement with the simulated ones.     

基于SRR-DGS 新型高选择性带通滤波器的设计

通过在阶梯阻抗谐振器(Stepped Impedance Resonators, SIR)上加载开口谐振环缺陷地结构(Split- Ring Resonator Defected Ground Structure, SRR-DGS),设计了一款具有高选择性和较好带外抑制性能的带通滤波器。 测试结果表明,该滤波器的3 dB 工作频带为2. 56 ~2. 77 GHz (7. 9%),带内最大插入损耗为0. 8 dB。此外,在通带 两侧各有两个传输零点,分别位于2. 17 GHz、2. 48 GHz、2. 86 GHz 和3. 81 GHz,带外抑制均大于30 dB,表明该滤波 器具有较好的带外抑制特性。同时,仿真与测试结果吻合较好,验证了该滤波器设计方法的有效性。     

Dual-band UWB bandpass filter with triangular DB-DGS for WLAN applications in DSRC band

A dual-band Ultra-wideband (UWB) bandpass microstrip filter with triangular dumbbell shaped defected ground structure (DB-DGS) for wireless local area network applications in DSRC band is proposed in this article. The proposed dual-band filter has center frequencies at 2.67 GHz and 4.68 GHz, return loss obtained is −33.40 dB and −16.55 dB respectively, wide bandwidth of 1.21 GHz (26%), pass band between 2.14 GHz and 6.44 GHz and high gain of 10.30 dB which makes it suitable for modern applications in dedicated short range communication operating in 5.8 GHz band. To further validate the design concept, a microstrip UWB filter is designed, fabricated and tested. Comparison is made among circular, square and triangular dumbbell shaped DGS on the basis of scattering parameters and bandwidth, in which triangular shaped DB-DGS outperforms the other two. Further, parametric analysis of triangular DB-DGS has been performed and comparison is made with filters of similar nature. Experimental results are in good agreement with simulations. The fabricated filter is compact in size, has low insertion loss, exhibits high selectivity and demonstrates excellent out of-band performance.     

Compact stub type microstrip bandpass filter using defected ground plane

Usually a defected ground plane structure (DGS) provides only a band-reject response. However, in this work we introduce a simple band-accept circuit element in the DGS and developed a microstrip stub type compact 3-pole bandpass filter (BPF) at 4.2 GHz. The BPF has bandwidth and insertion loss 38% and 0.6 dB respectively. It has better than 25 dB rejection in the stopband up to 12 GHz.     

Short-circuited CPW multiple-mode resonator for ultra-wideband (UWB) bandpass filter

An ultra-wideband (UWB: 3.1-10.6 GHz) bandpass filter (BPF) on coplanar waveguide (CPW) is proposed, designed and implemented. A nonuniform CPW multiple-mode resonator with short-circuited ends is constructed and its first three resonant modes are properly allocated around the lower-end, center and higher-end of the specified UWB band. This CPW resonator is then driven at two ends by two parallel-coupled CPW lines with dispersive inductive coupling degree. By properly reallocating the enhanced coupling peak toward the UWB's center, a five-pole CPW BPF with one full-wavelength can be eventually constituted. Its UWB bandpass performance is characterized and optimized on the basis of a simple transmission-line network. Predicted results are confirmed by experiment. Measured results achieve the insertion loss <1.5dB and group delay variation <0.35ns in the realized 3.3 to 10.4GHz UWB passband.     

Compact Ultra-Wideband Bandpass Filter Using Dual-Line Coupling Structure

This letter presents a novel compact ultra-wideband (UWB) microstrip bandpass filter with spurious response suppression. A dual-mode ring resonator is constituted to allocate its first two resonant frequencies in the UWB band, and the dual-line parallel-coupled structure is used in this compact UWB filter, which is expected to achieve much tighter coupling degree. Simulated and measured results are found in good agreement with each other, showing a wide passband from 4.9 to 10.9 GHz, 15 dB return loss bandwidth of about 5 GHz, minimum insertion loss of 0.49 dB at 7.3 GHz, and wide upper stopband with more than 20 dB attenuation up to 20 GHz.     

Miniaturized microstrip lowpass filter with wide stopband using double equilateral U-shaped defected ground structure

A compact double equilateral U-shaped defected ground structure (DGS) unit is proposed. In contrast to a single finite attenuation pole characteristic offered by the conventional dumbbell DGS, the proposed DGS unit provides dual finite attenuation poles that can be independently controlled by the DGS lengths. A 2.4-GHz microstrip lowpass filter using five cascaded double U-shaped DGS units is designed and compared with conventional DGS lowpass filters. This low pass filter achieves a wide stopband with overall 30-dB attenuation up-to10 GHz and more than 42% size diminution.     

A compact planar ultra-wideband bandpass filter with multiple resonant and defected ground structure

A compact bandpass filter with dumbbell shape Defected Ground Structure (DGS) operating on ultra wide pass band (UWB – 3.1 to 10.6 GHz) is proposed. It is based on hybrid microstrip coplanar waveguide (dual sided metal) structure. A Multiple Resonant Structure (MRS) is constructed using coplanar waveguide (CPW) planar transmission line. The MRS makes the resonance using quarter wavelength and half wavelength open-ended CPW. The equispaced three resonances at lower (3.1 GHz), center (6.85 GHz) and higher edge (10.6 GHz) of the whole Ultra Wide Band is achieved using CPW MRS. To make the band as flat as possible, two more resonances are introduced using quarter wavelength microstrip patches on top of the commonly shared substrate, so the proposed filter becomes a five pole bandpass filter. A dumbbell shaped defected ground structure on either side of CPW MRS improves the return loss almost less than 20 dB over the whole UWB passband. The simulated results of proposed filter show good transmission response within passband and good rejection in out of the band. The simulated and measured results are very close to each other which proves the efficacy of proposed design.     

EBG-Embedded Multiple-Mode Resonator for UWB Bandpass Filter With Improved Upper-Stopband Performance

An electromagnetic bandgap (EBG) embedded multiple-mode resonator (MMR) is proposed to constitute an upper-stopband-improved and size-miniaturized ultra-wideband (UWB) bandpass filter (BPF). This EBG-embedded MMR is studied to relocate its first three resonant modes within the 3.1-10.6GHz passband, whereas placing its 4th resonant mode at the coupling transmission zero of interdigital coupled-lines that drive this MMR at two sides. Meanwhile, the fifth resonant mode is rejected by virtue of the bandstop behavior of the EBG itself. Thus, a modified UWB BPF with widened upper-stopband, sharpened upper rejection skirt and lowered loss in the passband is finally constituted, designed and fabricated. The measured results demonstrate that the insertion loss is lower than 1.0 dB in the passband (4.0-10.6GHz) and higher than 15.0dB in the upper-stopband (12.0 to 20.0GHz) while the group delay variation in the passband is less than 0.2ns     

Quasi-elliptic filter characteristics of an asymmetric defected ground structure

An asymmetric defected ground structure (DGS) with respect to a microstrip line is proposed. Its unit cell consists of two square slots connected with a rectangular slot by meandered transverse slots. The simulated, measured and equivalent circuit responses have been presented. The unit DGS pattern under microstrip line produces wide rejection bandwidth and high sharpness factor. Its elliptic band-reject filter response is modelled by appropriate LC equivalent circuit. Two such DGS cells under a microstrip line produce 3-pole quasi-elliptic bandstop filter response, which shows deeper attenuation without appreciable change in pole frequencies in comparison to single cell structure. Unit DGS pattern under coupled gap microstrip lines produces band-accept filtering characteristics. The frequency characteristics show a quasi-elliptic highpass filtering characteristics with sharp lower transition knee. Accordingly, an LC equivalent circuit is proposed. A cascaded band-accept and band-reject filter is proposed for designing a wideband bandpass filter. The bandwidth and centre frequency of the bandpass filter can be varied by choosing different set of DGS dimensions.     

Analytical design of a microstrip UWB BPF with sharp rejection

This paper presents a new Ultra-WideBand (UWB) BandPass Filter (BPF) using half-wavelength (??/2) Stepped-Impedance Stub-Loaded Resonator (SISLR). Analytical equations derived by the even-odd mode analysis show the new filter has two tunable transmission zeros at both sides of the passband to provide a sharp rejection and seven transmission poles inside the passband to achieve U.S. UWB performance. For verification, a UWB BPF is designed, fabricated and measured. The measured results show that the fabricated filter has a -3 dB fractional bandwidth from 3.0 GHz to 10.9 GHz and its insertion loss less than 0.9 dB over the whole passband. Furthermore, the new filter exhibits a simple topology, sharp rejection, and deep stopband suppression.     

基于双层扇形基片集成波导的双频平衡滤波器

提出了一种表面刻有一对互补开环谐振器(CSRR)的45°扇形基片集成波导谐振腔(SSIWR),设计并制作了一款结构紧凑且具有高选择性的双层双频平衡带通滤波器.分别利用具有带通特性的CSRR和谐振腔内的TM220模实现了差模双频响应;模式间的耦合以及缺陷地结构(DGS)的引入使得滤波器在通带附近产生4个传输零点,提高了带...     

Novel Broadband Bandpass Filters Using Y-Shaped Dual-Mode Microstrip Resonators

A Y-shaped dual-mode microstrip bandpass filter (BPF) with input-output cross-coupling is presented. The characteristic of the Y-shaped dual-mode resonator has been investigated. The resonance frequencies of the degenerate modes can be adjusted easily to satisfy the bandwidth of the BPF. A parallel-coupling feed structure with a cross coupling has been used to generate two transmission zeros at the lower and upper stopband, which can improve the out-of-band performance. A broadband dual-mode microstrip BPF has been designed, fabricated, and measured. The simulated and measured results are in agreement generally. Within the 3.1 to 5.4 GHz bandwidth, the measured insertion loss, return loss and group delay variation are below 0.5 dB, above 15 dB, and below 0.2 ns, respectively.      

Design of the Compact Dual-Band Bandpass Filter With High Isolation for GPS/WLAN Applications

In this letter, a novel compact dual-band bandpass filter (BPF) is designed to achieve the characteristic of low insertion loss and high isolation for global position system (GPS)/wireless local area network (WLAN) applications. This BPF is implemented by properly selecting the impedance ratio (R) and physical length ratio $(alpha)$ of the asymmetric stepped-impedance resonator (SIR) with one step discontinuity. The coupling coefficient between the coupled asymmetric SIRs is calculated by using full-wave simulator IE3D. The proposed filter has very good measured characteristics including a low insertion loss of 1.1 dB for both passbands, a high isolation insertion loss of 55 dB between the two passbands and a wide stopband rejection of 38 dB from 2.7 to 5.3 GHz. Good agreement with responses of electromagnetic (EM) simulation and measurement is compared.