共查询到20条相似文献,搜索用时 93 毫秒
1.
2.
3.
4.
5.
从水泥立窑对通风设备的要求入手,分析了罗茨风机和高压离心风机的性能特点及对立窑工况的适应性,通过高压离心风机在立窑上的实残,可以看出高压离心风机不仅可以取代现在普遍采用的罗茨风机,而且也证明了高压离心风机作为立窑通风设备的节能降耗潜力。 相似文献
6.
7.
以某离心风机效率为优化目标,选定离心风机的4个关键参数:转速、叶轮直径、出口安装角、叶轮出口宽度,基于正交试验设计法,通过CFD数值仿真计算以及对计算结果的极差法分析,得出叶轮几何参数及转速的相对最优组合模型。组合模型计算结果表明,优化后风机达到设计要求。同时,优化组合模型风机静压效率可提高4.49%,全压效率提高6.94%。该研究方法适用于具有目标明确的风机改进设计,可快速精准获得优选方案。 相似文献
8.
9.
前缘缝翼是通过延缓流动分离和失速,提高飞机机翼升力,将前缘缝翼引入高负荷离心风机动叶的气动设计,以抑制叶片吸力面的边界层分离、改善风机气动性能,并基于数值模拟方法研究前缘缝翼起始位置和偏转角两个几何参数对风机流场与气动性能的影响。研究结果表明,30%弦长处为最佳开缝位置,其总压升和效率最大增幅分别达到13.1%和1.2%。动叶前缘缝翼的存在加速了后叶片吸力面流体的流动,抑制了后叶片尾部边界层的分离,且具有动叶前缘缝翼的离心叶轮速度分布更加均匀,压升更大。动叶前缘缝翼的开缝位置对提高离心风机总压升和效率具有重要的影响。 相似文献
10.
《节能技术》2015,(1)
为了探究MVR蒸汽离心风机在变工况时的运行性能,采用Fluetn软件,选用RNG k-ε湍流模型,对MVR蒸汽离心风机进行了数值模拟研究,研究了风机变工况流量为3.6 t/h、7.2 t/h、10.8 t/h、15 t/h、21.6 t/h、25.22 t/h的内部流场流动规律。研究结果表明:当风机进口流量降至7.2 t/h,气流在叶道内将产生边界层分离,风机发生旋转失速现象,风机效率将急剧降至56.4%;当流量继续降低至3.6 t/h,风机将发生喘振现象,风机的效率将急剧降低至35.6%;当风机进口流量达到25.22 t/h,风机不会发生边界层分离,但随着流量的增加,叶片气流速度会增加,流动损失增大,风机的效率降至59.3%。因此,MVR蒸汽离心风机在变流量工况运行时,效率将下降,在小流量工况下边界层分离是风机发生喘振现象的根本原因。 相似文献
11.
《International Journal of Hydrogen Energy》2022,47(63):26789-26797
The issues related to the reliability of hydrogen engines of unmanned vehicles and increasing the efficiency of using hydrogen as fuel when using the method of its production during the decomposition of hydrogen-containing molecules of liquid-phase organic compounds in a plasma discharge under the action of intense ultrasonic exposure are considered. Experiments have shown that as a result of decomposition in the acoustoplasma discharge of liquid hydrocarbons, solid-phase carbon-containing products are formed, chemical transformations occur in the liquid phase and hydrogen-containing combustible gas is formed. Hydrogen-containing gas can be used as fuel immediately after synthesis, i.e. it does not require separation, since in addition to hydrogen it contains only impurities of CO2 and water vapor. The purpose of the study is to formalize the basic conditions for tightening the control of mutual compliance with the efficiency of hydrogen engines of the same series in the conditions of their mass production. Methods of mathematical statistics and hardware-software modeling were used in the study. The term “unerroric of quality mutual compliance control” is introduced to describe a set of hardware and software tools for such control. The principle of in-depth testing of the technical condition of such engines of one series is described in a multidimensional formulation of the quality control problem for three of their operating parameters at once. The conditions for increasing the mutual correspondence of the measured values of such parameters in the conditions of serial production of hydrogen engines are formalized. 相似文献
12.
13.
14.
世界发电燃料结构在不断的转换过程中。18世纪60年代从薪柴转到煤炭,19世纪到20世纪初大量发展燃煤电厂;20世纪20年代又从煤炭转向石油和天然气,20年代上半叶又大量发展燃油电厂;20世纪末由于天然气生产的发展,天然气因环境影响小,受到工业发达国家的青睐,加速发展天然气电厂。我国70年代初和90年代曾两次发展燃油电厂,由于石油危机和石油价格暴涨而受到制约,不得不实行以煤代油,改造燃油电厂。现在似乎认为燃油电厂不能再搞,但又出现发展燃气电厂的热流,发展燃气电厂确实是当今的世界潮流,但是同当年发展燃油电厂一样,要研究是否符合中国的国情? 相似文献
15.
16.
本文从新型活塞设计的趋势及其对活塞车床的功能要求,讨论活塞车床的设计方案,并从机床功能、造型和宜人性上进行分析。 相似文献
17.
18.
19.
本文对漫灰均温物体在常物性条件下对外辐射传热的Yong值计算建立了数学模型。通过与物体内能Yong公式的数值计算比较,得出了辐射能量的Yong值不大于内能Yong值的结论。从初步的热射Yong值计算公式发现。Yong与物体表面辐射率有关。 相似文献
20.
本文对某型号柴油机热交换器支架裂纹的故障进行了材料分析,模态仿真和应变分析,找出了故障的根源,并根据分析结果提出设计改进建议。 相似文献