A 1-MHz-bandwidth second-order continuous-time quadrature bandpass sigma-delta modulator for low-IF radio receivers

This paper presents a quadrature bandpass /spl Sigma//spl Delta/ modulator with continuous-time architecture. Due to the continuous-time architecture and the inherent anti-aliasing filter, the proposed /spl Sigma//spl Delta/ modulator needs no additional anti-aliasing filter in front of the modulator in contrast to quadrature bandpass /spl Sigma//spl Delta/ modulators with switched-capacitor architectures. The second-order /spl Sigma//spl Delta/ modulator digitizes complex analog I/Q input signals at 1-MHz intermediate frequency and operates within a clock frequency range of 25-100 MHz. The modulator chip achieves a peak signal-to-noise-distortion ratio (SNDR) of 56.7 dB and a dynamic range of 63.8 dB within a 1-MHz signal bandwidth and at a clock frequency of 100 MHz. Furthermore, it provides an image rejection of at least 40 dB. The 0.65-/spl mu/m BiCMOS chip consumes 21.8 mW at 2.7-V supply voltage.     

A time-interleaved continuous-time /spl Delta//spl Sigma/ modulator with 20-MHz signal bandwidth

This paper presents the first implementation results for a time-interleaved continuous-time /spl Delta//spl Sigma/ modulator. The derivation of the time-interleaved continuous-time /spl Delta//spl Sigma/ modulator from a discrete-time /spl Delta//spl Sigma/ modulator is presented. With various simplifications, the resulting modulator has only a single path of integrators, making it robust to DC offsets. A time-interleaved by 2 continuous-time third-order low-pass /spl Delta//spl Sigma/ modulator is designed in a 0.18-/spl mu/m CMOS technology with an oversampling ratio of 5 at sampling frequencies of 100 and 200 MHz. Experimental results show that a signal-to-noise-plus-distortion ratio (SNDR) of 57 dB and a dynamic range of 60 dB are obtained with an input bandwidth of 10 MHz, and an SNDR of 49 dB with a dynamic range of 55 dB is attained with an input bandwidth of 20 MHz. The power consumption is 101 and 103 mW, respectively.     

IF-sampling fourth-order bandpass /spl Delta//spl Sigma/ modulator for digital receiver applications

Bandpass modulators sampling at high IFs (/spl sim/200 MHz) allow direct sampling of an IF signal, reducing analog hardware, and make it easier to realize completely software-programmable receivers. This paper presents the circuit design of and test results from a continuous-time tunable IF-sampling fourth-order bandpass /spl Delta//spl Sigma/ modulator implemented in InP HBT IC technology for use in a multimode digital receiver application. The bandpass /spl Delta//spl Sigma/ modulator is fabricated in AlInAs-GaInAs heterojunction bipolar technology with a peak unity current gain cutoff frequency (f/sub T/) of 130 GHz and a maximum frequency of oscillation (f/sub MAX/) of 130 GHz. The fourth-order bandpass /spl Delta//spl Sigma/ modulator consists of two bandpass resonators that can be tuned to optimize both wide-band and narrow-band operation. The IF is tunable from 140 to 210 MHz in this /spl Delta//spl Sigma/ modulator for use in multiple platform applications. Operating from /spl plusmn/5-V power supplies, the fabricated fourth-order /spl Delta//spl Sigma/ modulator sampling at 4 GSPS demonstrates stable behavior and achieves a signal-to-(noise + distortion) ratio (SNDR) of 78 dB at 1 MHz BW and 50 dB at 60 MHz BW. The average SNDR performance measured on over 250 parts is 72.5 dB at 1 MHz BW and 47.7 dB at 60 MHz BW.     

A 3.3-mW /spl Sigma//spl Delta/ modulator for UMTS in 0.18-/spl mu/m CMOS with 70-dB dynamic range in 2-MHz bandwidth

A quadrature fourth-order, continuous-time, /spl Sigma//spl Delta/ modulator with 1.5-b quantizer and feedback digital-to-analog converter (DAC) for a universal mobile telecommunication system (UMTS) receiver chain is presented. It achieves a dynamic range of 70 dB in a 2-MHz bandwidth and the total harmonic distortion is -74 dB at full-scale input. When used in an integrated receiver for UMTS, the dynamic range of the modulator substantially reduces the need for analog automatic gain control and its tolerance of large out-of-band interference also permits the use of only first-order prefiltering. An IC including an I and Q /spl Sigma//spl Delta/ modulator, phase-locked loop, oscillator, and bandgap dissipates 11.5 mW at 1.8 V. The active area is 0.41 mm/sup 2/ in a 0.18-/spl mu/m 1-poly 5-metal CMOS technology.     

A 25-MS/s 14-b 200-mW /spl Sigma//spl Delta/ Modulator in 0.18-/spl mu/m CMOS

The design of a fifth-order 4-b quantizer single-loop /spl Sigma//spl Delta/ modulator is presented that achieves 25-MS/s conversion rate with 84 dB of dynamic range and 82 dB of signal-to-noise ratio. Implemented in a 0.18-/spl mu/m CMOS technology, the 0.95-mm/sup 2/ chip has a power consumption of 200 mW from a 1.8-V supply.     

A 13-b 1.1-MHz oversampled DAC with semidigital reconstruction filtering

A digital-to-analog converter (DAC) composed of a cascaded digital /spl Sigma//spl Delta/ modulator and the combination of a semidigital/digital finite-impulse response (FIR) and an infinite-impulse response (IIR)-SC/RC filter is described. The architecture enables the analog linear reconstruction of 16/spl times/ oversampled digital signals. With the analog section implemented in CMOS 0.18-/spl mu/m and the digital part programmed into a field-programmable gate array (FPGA), the modulator plus reconstruction filter achieves a peak SNR of 78 dB. The spurious-free dynamic range reaches 80 dB and stays better than 73 dB within the 1.104-MHz signal band. A missing-tone-power ratio of 70 dB, demonstrated for a signal with 15-dB peak-to-average ratio, proves that the solution is suitable for ADSL-CO transmitters.     

A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.     

A 250-kHz 94-dB double-sampling /spl Sigma//spl Delta/ modulation A/D converter with a modified noise transfer function

This paper presents a high-order double-sampling single-loop /spl Sigma//spl Delta/ modulation analog-to-digital (A/D) converter. The important problem of noise folding in double-sampling circuits is solved here at the architectural level by placing one of the zeros in the modulator's noise transfer function at half the sampling frequency instead of in the baseband. The resulting modulator is of fifth order but has the baseband performance of a fourth-order modulator. Through the use of an efficient switched-capacitor implementation, the overall circuit uses only four operational amplifiers and hence, its complexity is similar to that of a fourth-order modulator. An experimental 1-bit modulator was designed for an oversampling ratio of 96 and a bandwidth of 250 kHz at a 3.3-V supply in a conservative 0.8-/spl mu/m standard CMOS process. Due to the double-sampling, the sampling frequency is 48 MHz, although the circuits operate at a clock frequency of only 24 MHz. The circuit achieves a dynamic range of 94 dB. The peak signal-to-noise ratio and signal-to-noise-plus-distortion ratio were measured to be 90 and 86 dB, respectively. The power consumption of the complete circuit including clock drivers and output pad drivers was 43 mW. The analog blocks (opamps, comparators, etc.) consume 30 mW of this total.     

A continuous-time sigma-delta modulator with 88-dB dynamic range and 1.1-MHz signal bandwidth

This paper presents the design and experimental results of a continuous-time /spl Sigma//spl Delta/ modulator for ADSL applications. Multibit nonreturn-to-zero (NRZ) DAC pulse shaping is used to reduce clock jitter sensitivity. The nonzero excess loop delay problem in conventional continuous-time /spl Sigma//spl Delta/ modulators is solved by our proposed architecture. A prototype third-order continuous-time /spl Sigma//spl Delta/ modulator with 5-bit internal quantization was realized in a 0.5-/spl mu/m double-poly triple-metal CMOS technology, with a chip area of 2.4 /spl times/ 2.4 mm/sup 2/. Experimental results show that the modulator achieves 88-dB dynamic range, 84-dB SNR, and 83-dB SNDR over a 1.1-MHz signal bandwidth with an oversampling ratio of 16, while dissipating 62 mW from a 3.3-V supply.     

A triple-mode continuous-time /spl Sigma//spl Delta/ modulator with switched-capacitor feedback DAC for a GSM-EDGE/CDMA2000/UMTS receiver

Time jitter in continuous-time /spl Sigma//spl Delta/ modulators is a known limitation on the maximum achievable signal-to-noise-ratio (SNR). Analysis of time jitter in this type of converter shows that a switched-capacitor (SC) feedback digital-to-analog converter (DAC) reduces the sensitivity to time jitter significantly. In this paper, an I and Q continuous-time fifth-order /spl Sigma//spl Delta/ modulator with 1-bit quantizer and SC feedback DAC is presented, which demonstrates the improvement in maximum achievable SNR when using an SC instead of a switched-current (SI) feedback circuit. The modulator is designed for a GSM/CDMA2000/UMTS receiver and achieves a dynamic range of 92/83/72 dB in 200/1228/3840 kHz, respectively. The intermodulation distance IM2, 3 is better than 87 dB in all modes. Both the I and Q modulator consumes a power of 3.8/4.1/4.5 mW at 1.8 V. Processed in 0.18-/spl mu/m CMOS, the 0.55-mm/sup 2/ integrated circuit includes a phase-locked loop, two oscillators, and a bandgap.     

A 1-V 3.5-mW CMOS switched-opamp quadrature IF circuitry for Bluetooth receivers

A 1-V switched-capacitor (SC) quadrature IF circuitry for Bluetooth receivers is demonstrated using switched-opamp technique. To achieve double power efficiency while maintaining low sensitivity to finite opamp gain effects for the SC IF circuitry, half-delay integrator-based filters and /spl Sigma//spl Delta/ modulator have been proposed. The proposed quadrature IF circuitry employs a seventh-order IF filter for channel selection and a third-order /spl Sigma//spl Delta/ modulator for analog-to-digital conversion. A noise-shaping extension technique is employed to enhance the resolution of the low-pass /spl Sigma//spl Delta/ modulator by 16 dB while operating at the same oversampling ratio and power consumption. At a 1-V supply, the quadrature IF circuitry achieves a measured IIP3 of -3 dBm at a nominal gain of 24 dB with a 48-dB variable gain control while consuming a total power dissipation of 3.5 mW.     

A 1.5-V 12-bit power-efficient continuous-time third-order /spl Sigma//spl Delta/ modulator

This paper presents the design strategy, implementation, and experimental results of a power-efficient third-order low-pass /spl Sigma//spl Delta/ analog-to-digital converter (ADC) using a continuous-time (CT) loop filter. The loop filter has been implemented by using active RC integrators. Several power optimizations, design requirements, and performance limitations relating to circuit nonidealities in the CT modulator are presented. The influence of the low supply voltage on the various building blocks such as the amplifier as well as on the overall /spl Sigma//spl Delta/ modulator is discussed. The ADC was implemented in a 3.3-V 0.5-/spl mu/m CMOS technology with standard threshold voltages. Measurements of the low-power 1.5-V CT /spl Sigma//spl Delta/ ADC show a dynamic range and peak signal-to-noise-plus-distortion ratio of 80 and 70 dB, respectively, in a bandwidth of 25 kHz. The measured power consumption is only 135 /spl mu/W from a single 1.5-V power supply.     

80-MHz bandpass /spl Delta//spl Sigma/ modulators for multimode digital IF receivers

Three fully differential bandpass (BP) /spl Delta//spl Sigma/ modulators are presented. Two double-delay resonators are implemented using only one operational amplifier. The prototype circuits operate at a sampling frequency of 80 MHz. The BP /spl Delta//spl Sigma/ modulators can be used in an intermediate-frequency (IF) receiver to combine frequency downconversion with analog-to-digital conversion by directly sampling an input signal from an IF of 60 MHz to a digital IF of 20 MHz. The measured peak signal-to-noise-plus-distortion ratios are 78 dB for 270 kHz (GSM), 75 dB for 1.25 MHz (IS-95), 69 dB for 1.762 MHz (DECT), and 48 dB for 3.84 MHz (WCDMA/CDMA2000) bandwidths. The circuits are implemented with a 0.35-/spl mu/m CMOS technology and consume 24-38 mW from a 3.0-V supply, depending on the architecture.     

A 2.2-mW CMOS bandpass continuous-time multibit /spl Delta/-/spl Sigma/ ADC with 68 dB of dynamic range and 1-MHz bandwidth for wireless applications

A delta-sigma (/spl Delta//spl Sigma/) analog-to-digital converter featuring 68-dB dynamic range and 64-dB signal-to-noise ratio in a 1-MHz bandwidth centered at an intermediate frequency of 2 MHz with a 48-MHz sample rate is reported. A second-order continuous-time modulator employing 4-bit quantization is used to achieve this performance with 2.2 mW of power consumption from a 1.8-V supply. The modulator including references occupies 0.36 mm/sup 2/ of die area and is implemented in a 0.18-/spl mu/m five-metal single-poly digital CMOS process.     

A 92-MHz 13-bit IF digitizer using optimized SC integrators in 0.35-/spl mu/m CMOS technology

A feedforward compensation scheme with no Miller capacitors is proposed to overcome the bandwidth limitations of traditional Miller compensation schemes. The technique has been used in the design of an operational transconductance amplifier (OTA) with a dc gain of 80 dB, gain bandwidth of 1.4 GHz, phase margin of 62/spl deg/, and 2 ns settling time for 2-pF load capacitor in a standard 0.35-/spl mu/m CMOS technology. The OTA's current consumption is 4.6 mA. The OTA is used in the design of a fourth-order switched-capacitor bandpass /spl Sigma//spl Delta/ modulator with a clock frequency of 92 MHz. It achieves a peak signal-to-noise ratio of 80 and 54 dB for 270-kHz (GSM) and 3.84-MHz (CDMA) bandwidths, respectively and consumes 19 mA of current from a /spl plusmn/1.25-V supply.     

Hybrid /spl Sigma//spl Delta/ modulators with adaptive calibration

This paper describes an architecture for stable high-order /spl Sigma//spl Delta/ modulation. The architecture is based on a hybrid /spl Sigma//spl Delta/ modulator, wherein hybrid integrators replace conventional analog integrators. The hybrid integrator, which is a combination of an analog integrator and a digital integrator, offers an increased dynamic range and helps make the resulting high-order /spl Sigma//spl Delta/ modulator stable. However, the hybrid /spl Sigma//spl Delta/ modulator relies on precise matching of analog and digital paths. In this paper, a calibration technique to alleviate possible mismatch between analog and digital paths is proposed. The calibration adaptively adjusts the digital integrators so that their transfer functions match the transfer functions of corresponding analog integrators. Through behavioral-level simulations of fourth-order /spl Sigma//spl Delta/ modulators, the calibration technique is verified.     

Gain and offset mismatch calibration in time-interleaved multipath A/D sigma-delta modulators

We propose a digital background adaptive calibration technique for correcting offset and gain mismatches in time-interleaved multipath analog-digital (A/D) sigma-delta (/spl Sigma//spl Delta/) modulators. The proposed technique allows us to cancel the spurious tones introduced by offset and gain mismatches among the paths only by processing the digital output, without interfering with the operation of the modulator. This solution is also effective for any other time-interleaved A/D converter topology. Simulation results on a high-performance four-path bandpass /spl Sigma//spl Delta/ modulator, operating on a 5-MHz band at a clock frequency of 320 MHz, demonstrate the effectiveness of the proposed calibration technique, which allows us to achieve significant improvements of the signal-to-noise ratio and the spurious-free dynamic range in the presence of mismatches.     

A CMOS 110-dB@40-kS/s programmable-gain chopper-stabilized third-order 2-1 cascade sigma-delta Modulator for low-power high-linearity automotive sensor ASICs

This paper describes a 0.35-/spl mu/m CMOS chopper-stabilized switched-capacitor 2-1 cascade /spl Sigma//spl Delta/ modulator for automotive sensor interfaces. The modulator architecture has been selected from an exhaustive comparison among multiple topologies in terms of resolution, speed and power dissipation. To obtain a better fitting with the characteristics of different sensor outputs, the circuit can be digitally programmed to yield four input-to-output gain values (/spl times/0.5,/spl times/1,/spl times/2, and /spl times/4) and has been designed to operate within the stringent environmental conditions of automotive electronics (temperature range of -40/spl deg/C to 175/spl deg/C). In order to relax the amplifier's dynamic requirements for the different modulator input-to-output gains, switchable capacitor arrays are used for all the capacitors in the first integrator. The design of the building blocks is based on a top-down CAD methodology which combines simulation and statistical optimization at different levels of the modulator hierarchy. The circuit is clocked at 5.12 MHz and the overall power consumption is 14.7 mW from a single 3.3-V supply and occupies 5.7 mm/sup 2/ silicon area. Experimental results show a maximum SNR of 87.3 dB within a 20-kHz signal bandwidth and 90.7 dB for 10-kHz signals, and an overall DR of 110 and 113.8dB, respectively. These performance features place the reported circuit at the cutting edge of state-of-the-art high-resolution /spl Sigma//spl Delta/ modulators.     

A 10.7-MHz self-calibrated switched-capacitor-based multibit second-order bandpass /spl Sigma//spl Delta/ modulator with on-chip switched buffer

A second-order multibit bandpass /spl Sigma//spl Delta/ modulator (BP/spl Sigma//spl Delta/M) used for the digitizing of AM/FM radio broadcasting signals at a 10.7-MHz IF is presented. The BP/spl Sigma//spl Delta/M is realized with switched-capacitor (SC) techniques and operates with a sampling frequency of 37.05 MHz. The input impulse current, required by the SC input branch, is minimized by the use of a switched buffer without deteriorating the overall system performance. The accuracy of the in-band noise shaping is ensured with two self-calibrating control systems. In a 0.18-/spl mu/m CMOS technology, the device die size is 1 mm/sup 2/ and the power consumption is 88 mW. In production, the BP/spl Sigma//spl Delta/M features at least 78-dB dynamic range and 72-dB peak SNR within a 200-kHz bandwidth (FM bandwidth). The intermodulation (IMD) is -65 dBc for two tones at -11 dBFS. The robustness of the aforementioned performance is demonstrated by the fact that it has been realized with the BP/spl Sigma//spl Delta/M embedded in the noisy on-chip environment of a complete mixed-signal FM receiver.     

A time-delay jitter-insensitive continuous-time bandpass /spl Delta//spl Sigma/ modulator architecture

In this paper, we present a new continuous-time bandpass delta-sigma (/spl Delta//spl Sigma/) modulator architecture with mixer inside the feedback loop. The proposed bandpass /spl Delta//spl Sigma/ modulator is insensitive to time-delay jitter in the digital-to-analog conversion feedback pulse, unlike conventional continuous-time bandpass /spl Delta//spl Sigma/ modulators. The sampling frequency of the proposed /spl Delta//spl Sigma/ modulator can be less than the center frequency of the input narrow-band signal.