Speciation of dissolved iron(III) and iron(II) in water by on-line coupling of flow injection separation and preconcentration with inductively coupled plasma mass spectrometry

A method has been developed for the speciation of trace dissolved Fe(II) and Fe(II) in water by on-line coupling of flow injection separation and preconcentration with inductively coupled plasma mass spectrometry (ICPMS). Selective determination of Fe(III) in the presence of Fe(II) was made possible by on-line formation and sorption of the Fe(III)-pyrrolidinecarbodithioate (PDC) complex in a PTFE knotted reactor over a sample acidity range of 0.07-0.4 mol L(-1) HCl, elution with 1 mol L(-1) HNO3, and detection by ICPMS. Over a sample acidity range of 0.001-0.004 mol L(-1) HCl, the sum of Fe(III) and Fe(II), i.e., Fe(III + II), could be determined without the need for preoxidation of Fe(II) to Fe(III). The concentration of Fe(II) was obtained as the difference between those of Fe(III + II) and Fe(III). With a sample flow rate of 5 mL min(-1) and a 30-s preconcentration time, an enhancement factor of 12, a retention efficiency of 80%, and a detection limit (3s) of 0.08 microg L(-1) were obtained at a sampling frequency of 21 samples h(-1). The relative standard deviation (n = 11) was 2.9% at the 10 microg L(-1) Fe(III) level. Recoveries of spiked Fe(III) and Fe(II) in local tap water, river water, and groundwater samples ranged from 95% to 103%. The concentrations of Fe(III) and Fe(II) in synthetic aqueous mixtures obtained by the proposed method were in good agreement with the spiked values. The result for total iron concentration in the river water reference material SLRS-3 was in good agreement with the certified value. The method was successfully applied to the determination of trace dissolved Fe(III) and Fe(II) in local tap water, river water, and groundwater samples.     

The facile flow-injection spectrophotometric detection of gold(III) in water and pharmaceutical samples using 3,5-dimethoxy-4-hydroxy-2-aminoacetophenone isonicotinoyl hydrazone (3,5-DMHAAINH)

A simple, sensitive and rapid flow-injection spectrophotometric method was developed for the determination of trace amounts of Au(III) in aqueous dimethylformamide (DMF). The method is based on formation of Au(III)-(3,5-DMHAAINH)3 complex. The optimum conditions for the chromogenic reaction of Au(III) with 3,5-DMHAAINH is studied and the colored (reddish brown) complex is selectively monitored at lambda(max) 490 nm at pH 6.0. The reaction and flow conditions of the full experimental design were optimized. The detection limit (2 s) of 0.1 microg l-1 Au(III) was obtained at a sampling rate of 15 samples h-1. Beer's law is obeyed over the range of 0.30-4.00 microg ml-1. The molar absorptivity and Sandell's sensitivity were 3.450x10(4) M and 0.0050 microg ml-1, respectively. Job's method of continuous variation and stability constants corresponding to these maxima was determined and found to be 9.3x10(15) (1:3, M:R) (M, metal; R, reagent). The detailed study of various interferences confirmed the high selectivity of the developed method. The method was successfully applied for the determination of trace amount of Au(III) in water and pharmaceutical samples. The results obtained were in agreement with the reported methods at the 95% confidence level.     

Extractive spectrophotometric method for determination of metribuzin herbicide and application of factorial design in optimization of various factors

A simple extractive spectrophotometric method has been described for the determination of metribuzin herbicide. Metribuzin was reacted with copper and a stable complex in the presence of ammonia (0.2M) at pH 10.5 was formed. The resulting yellow coloured complex was extracted in chloroform and showed absorption maxima at 340 nm. Beer's law was obeyed in the range of 0.8-25 microg mL(-1) with molar absorptivity of 5.67 x 10(3)L mol(-1)cm(-1). The composition of the complex was studied by Job's method of continuous variation and the results indicated that the mole ratio of metribuzin:Cu(2+) is 2:1. The optimum reaction conditions for complexation and other analytical parameters were evaluated. A two-level factorial design was also used to determine the effect of different parameters and their interaction on metribuzin:Cu(2+) complex formed. The method was successfully applied for the determination of metribuzin in commercial formulations and real samples.     

Selective and sensitive spectrophotometric method for determination of sub-micro-molar amounts of aluminium ion

A simple and accurate spectrophotometric method for determination of trace and ultra-trace amounts of Al3+ ion in tap and wastewater sample has been described. Using the eriochrome cyanine R (ECR) in the presence of N,N-dodecyltrimethylammonium bromide (DTAB) as cationic surfactant spectrophotometric determination of Al3+ ion has been carried out. The Beer's law is obeyed over the concentration range of 4-400 ng mL(-1) of Al3+ ion with the detection limits of 0.14 ng mL(-1), while the molar absorptivity of complexes is 1.19x10(5) L mol(-1) cm(-1). The influence of type and amount of surfactant, pH, and amount of ligand on sensitivity of spectrophotometric method were optimized. The method has been successfully applied for Al3+ ion determination in real sample.     

Extractive spectrophotometric determination of trace amounts of cadmium(II) in medicinal leaves and environmental samples using benzildithiosemicarbazone (BDTSC)

A new thiosemicarbazone, benzildithiosemicarbazone (BDTSC), is proposed as a sensitive and selective analytical reagent for extractive spectrophotometric determination of Cd(II). BDTSC reacts with cadmium(II) to give a yellow-colored complex in ammonium chloride-ammonium hydroxide buffer of pH 10.5, which is easily extracted into isoamylalcohol with 1:1 composition having a maximum absorbance at wavelength 360 nm. The molar absorptivity and Sandell's sensitivity are found to be 0.196 x 10(4)dm3 mol(-1)cm(-1) and 0.008 microg cm(-2) of Cd(II), respectively. The instability constant of the method has been calculated by Asmus' method as 5.05 x 10(-5) (which is in close agreement with the value obtained by Edmonds and Birnbaum's method) at room temperature. The interfering effect of various cations and anions has also been studied. The method has been successfully applied for the determination of Cd(II) in several standard reference materials as well as environmental samples, medicinal leaves and leafy vegetables.     

Solid phase extraction method for the determination of iron, lead and chromium by atomic absorption spectrometry using Amberite XAD-2000 column in various water samples

This work describes a procedure for the separation-preconcentration of Fe(III), Pb(II) and Cr(III) from some water samples using a column-filled Amberlite XAD-2000 resin. The analyte ions retained on the column were eluted with 0.5 mol L(-1) HNO(3). The analytes in the effluent were determined by atomic absorption spectrometry. Several parameters governing the efficiency of the method were evaluated including pH, resin amount, sample volume, flow rates, eluent type and divers ion effects. The recoveries under the optimum working conditions were found to be as 100+/-1% Fe, 96+/-1% Pb and 93+/-2% Cr. The relative standard deviations and errors were less than 2% and 5%, respectively. The detection limit based on three standard deviations of the blank was found to be 0.32, 0.51 and 0.81 microg L(-1), for Fe, Pb and Cr, respectively. The procedure was applied to the determination of Fe, Cr and Pb in hot spring water and drinking water samples.     

Gadolinium hydroxide coprecipitation system for the separation-preconcentration of some heavy metals

A simple and new procedure for the determination of trace amounts of lead(II), cobalt(II), manganese(II) and copper(II) is described, that combines atomic absorption spectrometry-gadolinium hydroxide coprecipitation. One milliliter of 1% gadolinium(III) solution was added to each sample; the pH was then adjusted to 11 in order to collect trace heavy metals on gadolinium(III) hydroxide. The precipitate was separated by centrifugation and dissolved in 1 mL of 1 mol L(-1) HNO3. The influences of analytical parameters including amount of gadolinium(III), sample volume, etc. were investigated on the recoveries of analyte ions. The effects of concomitant ions were also examined. The recoveries of the analyte ions were greater than 95. The detection limits for the analyte elements based on 3 sigma (n=20) were in the range of 0.52-12.0 microg L(-1). The method was applied to the determination of analytes in real samples and good results were obtained (relative standard deviations <10%, recoveries >95%).     

Tris(2-aminoethyl) amine functionalized silica gel for solid-phase extraction and preconcentration of Cr(III), Cd(II) and Pb(II) from waters

A new tris(2-aminoethyl) amine (TREN) functionalized silica gel (SG-TREN) was prepared and investigated for selective solid-phase extraction (SPE) of trace Cr(III), Cd(II) and Pb(II) prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Identification of the surface modification was characterized and performed on the basis of FT-IR. The separation/preconcentration conditions of analytes were investigated, including effects of pH, the shaking time, the sample flow rate and volume, the elution condition and the interfering ions. At pH 4, the maximum adsorption capacity of Cr(III), Cd(II) and Pb(II) onto the SG-TREN were 32.72, 36.42 and 64.61 mg g(-1), respectively. The adsorbed metal ions were quantitatively eluted by 5 mL of 0.1 mol L(-1) HCl. Common coexisting ions did not interfere with the separation. According to the definition of International Union of Pure and Applied Chemistry, the detection limits (3sigma) of this method for Cr(III), Cd(II) and Pb(II) were 0.61, 0.14 and 0.55 ng mL(-1), respectively. The relative standard deviation under optimum conditions is less than 4.0% (n=11). The application of this modified silica gel to preconcentration trace Cr(III), Cd(II) and Pb(II) of two water samples gave high accurate and precise results.     

On-line preconcentration of copper as its pyrocatechol violet complex on Chromosorb 105 for flame atomic absorption spectrometric determinations

An on-line solid phase extraction method for the preconcentration and determination of Cu(II) by flame atomic absorption spectrometry (FAAS) has been described. It is based on the adsorption of copper(II) ion onto a home made mini column of Chromosorb 105 resin loaded with pyrocatechol violet at the pH range of 5.0-8.0, then eluted with 1 mol L(-1) HNO(3). Several parameters, such as pH of the sample solution, amount of Chromosorb 105 resin, volume of sample and eluent, type of eluent, flow rates of sample and eluent, governing the efficiency and throughput of the method were evaluated. The concentration of the copper ion detected after preconcentration was in agreement with the added amount. At optimized conditions, for 15 min of preconcentration time (30 mL of sample volume), the system achieved a detection limit of 0.02 microg L(-1), with relative standard deviation 1.1% at 0.03 microg mL(-1) copper. The present method was found to be applicable to the preconcentration of Cu(II) in natural water samples.     

Diaion SP-850 resin as a new solid phase extractor for preconcentration-separation of trace metal ions in environmental samples

A solid phase extraction method was developed for the preconcentration and separation of trace amounts of chromium, manganese, iron, cobalt, copper, cadmium and lead from environmental samples by complexation with alpha-benzoin oxime followed by adsorption onto Diaion SP-850-solid phase extraction column. One molar per liter HNO(3) was used as eluent. The recoveries of analytes at pH 8.0 with 700 mg of resin were greater than 95% without interference from alkaline, earth alkaline and some metal ions. The detection limits by three sigma for analyte ions were 0.65 microg l(-1) for Cr(III), 0.42 microg l(-1) for Mn(II), 0.28 microg l(-1) for Fe(III), 0.73 microg l(-1) for Co(II), 0.30 microg l(-1) for Cu(II), 0.47 microg l(-1) for Cd(II) and 0.50 microg l(-1) for Pb(II). The validation of the procedure was performed by the analysis of the certified standard reference materials. The presented procedure was applied to the determination of analytes in tap, river and sea waters, rice, wheat, canned tomato and coal samples with successfully results (recoveries greater than 95%, R.S.D.'s lower than 8%).     

A biosorption system for metal ions on Penicillium italicum-loaded on Sepabeads SP 70 prior to flame atomic absorption spectrometric determinations

A solid phase extraction (SPE) preconcentration system, coupled to a flame atomic absorption spectrometer (FAAS), was developed for the determination of copper(II), cadmium(II), lead(II), manganese(II), iron(III), nickel(II) and cobalt(II) ions at the microg L(-1) levels on Penicillium italicum-loaded on Sepabeads SP 70. The analytes were adsorbed on biosorbent at the pH range of 8.5-9.5. The adsorbed metals were eluted with 1 mol L(-1) HCl. The influences of the various analytical parameters including pH of the aqueous solutions, sample volume, flow rates were investigated for the retentions of the analyte ions. The recovery values are ranged from 95-102%. The influences of alkaline, earth alkaline and some transition metal ions were also discussed. Under the optimized conditions, the detection limits (3s, n=21) for analytes were in the range of 0.41microg L(-1) (cadmium) and 1.60microg L(-1) (iron). The standard reference materials (IAEA 336 Lichen, NIST SRM 1573a Tomato leaves) were analyzed to verify the proposed method. The method was successfully applied for the determinations of analytes in natural water, cultivated mushroom, lichen (Bryum capilare Hedw), moss (Homalothecium sericeum) and refined table salt samples.     

Solid-phase extraction of Fe(III), Pb(II) and Cr(III) in environmental samples on amberlite XAD-7 and their determinations by flame atomic absorption spectrometry

This paper describes a simple and accurate procedure for preconcentration of trace amounts of Fe(III), Pb(II) and Cr(III) ions. The preconcentration procedure is based on retention of p-xylenol blue chelates on Amberlite XAD-7. The analytes retained were eluted from Amberlite XAD-7 by using 1 mol L(-1) HCl. The influences of the analytical parameters including amounts of reagents, pH and type of eluent were also investigated. The detection limits of Fe, Pb and Cr were found to be 3.07, 18.6 and 3.27 microg L(-1), respectively. The accuracy of the procedure was checked by the analysis of an electrolytic copper wire sample. The relative error was less than 5%. The presented method was applied to the determination of Fe(III), Pb(II) and Cr(III) in water samples from Denizli, Turkey with good results such as recoveries more than 95%, relative standard deviations below 10%.     

An optical fiber chemical sensor for mercury ions based on a porphyrin dimer

The synthesis of a novel fluoroionophore, 5-p-[[4-(10',15',20'-triphenyl-5'-porphinato) phenyloxyl]-1-butyloxyl]phenyl-10,15,20-triphenylporphine (DTPP), and its application for preparation of a Hg(II)-sensitive optical fiber chemical sensor are described. The response of the sensor is based on the fluorescence quenching of DTPP by coordination with Hg(II). The porphyrin dimer-based sensor shows a linear response toward Hg(II) in the concentration range 5.2 x 10(-7)-3.1 x 10(-4) mol x L(-1), with a working pH range from 2.4 to 8.0. The sensor shows excellent selectivity for Hg(II) over transition metal cations including Cd(II), Co(II), Cu(II), Ni(II), Pb(II), Zn(II), and Fe(III). As a sensing agent, the porphyrin dimer shows obviously better fluorescence response characteristics toward Hg(II) compared to porphyrin monomer or metalloporphyrin. The effect of the composition of the sensor membrane was studied, and the experimental conditions were optimized. The sensor has been used for determination of Hg(II) in water samples.     

Flow injection on-line sorption preconcentration coupled with hydride generation atomic fluorescence spectrometry for determination of (ultra)trace amounts of arsenic(III) and arsenic(V) in natural water samples

A flow injection on-line sorption preconcentration and separation in a knotted reactor (KR) was coupled to hydride generation atomic fluorescence spectrometry (HG-AFS) for speciation of inorganic arsenic in natural water samples. The method involved on-line formation of the As(III)-pyrrolidinedithiocarbamate (PDC) complex over a sample acidity of 0.001-0.1 mol L(-1) HCl, its adsorption onto the inner walls of the KR made from 150-cm long x 0.5-mm i.d. PTFE tubing, elution withmol L(-1) HCl, and detection by HG-AFS. Total inorganic arsenic was determined after prereduction of As(V) to As(III) with 1% m/v L-cysteine. The concentration of As(V) was calculated by the difference of the total inorganic arsenic and As(III). A 1 mol L(-1) concentration of HCl was employed not only as the efficient eluent but also as the required medium for subsequent hydride generation. Potential factors that affect adsorption, rinsing, elution, and hydride generation were investigated in detail. The low cost, easy operation, and high sensitivity are the obvious advantages of the present system. With consumption of a 6 mL sample solution, an enhancement factor of 11 and a detection limit (3s) of 0.023 microg L(-1) As(III) were obtained at a sample throughput of 32 h(-1). The precision for 14 replicate measurements of 1 microg L(-1) As(III) was 1.3% (RSD). The recoveries from natural water samples varied from 96.7 to 105% for 2 microg L(-1) of As(III) spike and from 97.1 to 107% for 2 microg L(-1) of As(V) spike. The analytical results obtained by the present method for total arsenic in the certified reference materials, SLRS-4 (river water) and NASS-5 (seawater), agreed well with the certified values. The developed method was also successfully applied to the speciation of inorganic arsenic in local natural water samples.     

An on-line pre-concentration system for determination of cadmium in drinking water using FAAS

In the present paper, a minicolumn of polyurethane foam loaded with 4-(2-pyridylazo)-resorcinol (PAR) is proposed as pre-concentration system for cadmium determination in drinking water samples by flame atomic absorption spectrometry. The optimization step was performed using two-level full factorial design and Doehlert matrix, involving the variables: sampling flow rate, elution concentration, buffer concentration and pH. Using the established experimental conditions in the optimization step of: pH 8.2, sampling flow rate 8.5 mL min(-1), buffer concentration 0.05 mol L(-1) and elution concentration of 1.0 mol L(-1), this system allows the determination of cadmium with detection limit (LD) (3sigma/S) of 20.0 ng L(-1) and quantification limit (LQ) (10sigma/S) of 64 ng L(-1), precision expressed as relative standard deviation (R.S.D.) of 5.0 and 4.7% for cadmium concentration of 5.0 and 40.0 microg L(-1), respectively, and a pre-concentration factor of 158 for a sample volume of 20.0 mL. The accuracy was confirmed by cadmium determination in the standard reference material, NIST SRM 1643d trace elements in natural water. This procedure was applied for cadmium determination in drinking water samples collected from Salvador City, Bahia, Brazil. For five samples analyzed, the achieved concentrations varied from 0.31 to 0.86 microg L(-1).     

Determination of Co(II) in water and soil samples using spectrophotometry coupled with preconcentration on 4-amino methyl pyridine anchored silica gel column

4-amino methyl pyridine anchored silica gel (4-AMPS) was used as a sorbent in a simple sensitive spectrophotometry determination of Co(II) in various samples using piperazine dithiocarbamate as a color developing agent (lambda(max)=390 nm) at pH 5.0+/-0.2. Beer's law was obeyed over the range of 0.1-5.0 microg ml(-1). The molar absorptivity and Sandell's sensitivity were 1.257x10(5) lmol(-1) cm(-1) and 0.006145 microg cm(-2), respectively. Under these conditions, the preconcentration factor obtained was 80, and the detection limit achieved was 5.0 ng ml(-1). The detailed study of various interfering ions made the method more sensitive and selective. The recovery of Co(II) from various samples range from 97.50 to 99.66%. The present method was successfully applied for the determination of Co(II) in various water and soil samples. The proposed method was compared with reported methods in terms of Student's 't'-test and variance ratio 'f'-test which indicates that there is no significant difference between proposed and literature method at 95% confidence level.     

An experimental design to optimize the flow extraction parameters for the selective removal of Fe(III) and Al(III) in aqueous samples using salicylic acid grafted on Amberlite XAD-4 and final determination by GF-AAS

In this paper, a multivariable approach has been applied for the selective removing of Fe(III) and Al(III), in the range 0-200 microg l(-1), in water samples onto a modified organic support (salicylic acid grafted on XAD-4). An empirical mathematical model was designed which establishes the relationship between the variation of the responses (extraction yields), and the variation of three factors (sample volume, sample percolation flow rate and amount of metallic ions present in the sample). To estimate the coefficients of the developed model, an uniform shell Doehlert design has been applied; these experiments consisted in GF-AAS determination of aluminium and iron amounts in eluates after percolation of samples through modified support. Results show a similar behaviour of the resin towards aluminium and iron with a preponderant effect of the percolation flow rate value; however this one is crucial for aluminium extraction and should be maintained below to 0.55 ml min(-1) to reach a 95% Al3+ extraction yield (versus 2.25 ml min(-1) for Fe3+). The optima determined by this experimental design approach have been further applied to the selective extraction of aluminium and iron from multielement synthetic samples and from real samples at the outlet of potable water treatment units.     

4-(5-氯-2-吡啶)-偶氮-1,3-二氨基苯光度法测定电镀废水中的微量镍(Ⅱ)

4-(5-氯-2-吡啶)-偶氮-1,3-二氨基苯(5-Cl-PADAB)可与镍发生灵敏的显色反应,生成稳定的配位化合物。基于此建立了一种测定电镀废水中微量镍的光度法。结果表明:在2.0 mol/L HCl介质中,5-Cl-PADAB与Ni(Ⅱ)反应生成摩尔比2∶1的稳定配位化合物,其最大吸收波长为565 nm,表观摩尔吸光系数为6.42×104 L/(mol.cm),Ni(Ⅱ)含量在0～1.0 mg/L内符合比尔定律;该方法用于测定电镀废水中微量镍,结果与催化-分光光度法相符,相对标准偏差小于4.0%,加标回收率为98.5%～101.8%。     

Study on solid phase extraction and graphite furnace atomic absorption spectrometry for the determination of nickel, silver, cobalt, copper, cadmium and lead with MCI GEL CHP 20Y as sorbent

A solid phase extraction and graphite furnace atomic absorption spectrometry (GFAAS) for the determination of nickel, silver, cobalt, copper, cadmium and lead with MCI GEL CHP 20Y as sorbent was studied. Trace amounts of chromium, nickel, silver, cobalt, copper, cadmium and lead were reacted with 2-(2-quinolinil-azo)-4-methyl-1,3-dihydroxidobenzene (QAMDHB) followed by adsorption onto MCI GEL CHP 20Y solid phase extraction column, and 1.0molL(-1) HNO(3) was used as eluent. The metal ions in 300mL solution can be concentrated to 1.0mL, representing an enrichment factor of 300 was achieved. The recoveries of analytes at pH 8.0 with 1.0g of resin were greater than 95% without interference from alkaline, earth alkaline and some metal ions. When detected with graphite furnace atomic absorption spectrometry, the detection limits in the original samples were 1.4ngL(-1) for Cr(III), 1.0ngL(-1) for Ni(II), 0.85ngL(-1) for Ag(I), 1.2ngL(-1) for Co(II), 1.0ngL(-1) for Cu(II), 1.2ngL(-1) for Cd(II) and 1.3ngL(-1) for Pb(II). The validation of the procedure was performed by the analysis of the certified standard reference materials, and the presented procedure was applied to the determination of analytes in biological, water and soil samples with good results (recoveries range from 89 to 104%, and R.S.D.% lower than 3.2%. The results agreed with the standard value or reference method).     

Development of cloud point extraction for simultaneous extraction and determination of gold and palladium using ICP-OES

Cloud point method was applied for the simultaneous extraction and preconcentration of trace amounts of gold and palladium. The extraction of analytes was performed in the presence of 1,8-diamino-4,5-dihydroxy anthraquinone as chelating agent and Triton X-114 as a non-ionic surfactant. After phase separation, the surfactant-rich phase was diluted with concentrated HNO(3) (65%, w/w) and the analytes concentrations were determined by inductively coupled plasma-optical emission spectrometry (ICP-OES). The variables affecting the complexation and extraction conditions were optimized and under the optimum conditions (i.e. pH 6.5, 2.2 x 10(-4) mol l(-1) chelating agent, 0.15% (w/v) of Triton X-114, equilibration temperature 55 degrees C, centrifuge at 3500 rpm), quantitative extraction of Au(III) and Pd(II) from 100 ml of the aqueous solution was performed. The calibration curves were linear in the range of 0.5-1000 microg l(-1) with detection limits of 0.5 and 0.3 microg l(-1) and the enrichment factors were 8.6 and 20.2 for Au and Pd, respectively. Also the precision (%RSD) for eight replicate determinations of the analytes was better than 5%. Finally, the proposed method was successfully applied for the determination of Au and Pd in mine stones and standard reference materials (SRM).