Cassava starch‐graft‐polymethacrylamide copolymers as flocculants and textile sizing agents

Cassava starch‐graft‐polymethacrylamide (PMAM) copolymers were synthesized by a free‐radical‐initiated polymerization reaction, and the products were tested for their efficiency as flocculants and textile sizing agents. The highest percentages of grafting and monomer conversion were 79.9 and 78.0%, respectively. The grafted starches were characterized by Fourier transform infrared spectroscopy, X‐ray diffraction analysis, scanning electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The average molecular weight of PMAM chains in the grafted starches ranged from 15.9 to 30.8 × 10⁵ g/mol. The grafted starches exhibited a higher peak viscosity and paste stability in comparison to the native starch (NS). Dynamic mechanical analysis showed that grafting provided fairly shear‐stable hydrogels, and the highest storage modulus obtained was 17,900 Pa compared to 1879 Pa for NS. The flocculation studies demonstrated the superiority of starch‐g‐PMAM over cassava starch and PMAM as an efficient flocculant. The tensile strength of cotton yarns sized with the starch‐grafted copolymer was significantly higher (104 MPa) compared to that sized with NS (34 MPa). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39810.     

Swelling and rheology of saponified starch–g–polyacrylonitrile copolymers. Effect of starch granule pretreatment and grafted chain length

A series of well-characterized starch–g–polyacrylonitrile (PAN) graft copolymers was prepared from corn starch which had been heated in water at temperatures up to 94°C to vary the extent of starch granule swelling and disruption. Graft polymerization onto gelatinized starch gave less frequent grafting of higher molecular weight PAN than comparable graft polymerizations onto ungelatinized starch. A graft copolymer was also prepared from gelatinized starch under high dilution conditions to give lower molecular weight grafted PAN and more frequent grafting. Graft copolymers were then saponified with sodium hydroxide to convert nitrile substituents to a mixture of carboxamide and sodium carboxylate. Saponified graft copolymers were only partially water soluble and consisted largely of highly swollen, insoluble gel, which was separated from solubles for the study of physical properties. Saponification mixtures were also dried to yield highly absorbent polymer films. With the exception of the graft copolymer prepared under high dilution conditions, the physical properties of saponified graft copolymers depended on whether or not the granules of starch were gelatinized before graft polymerization. Compared with saponified graft copolymers derived from ungelatinized starch, those prepared from gelatinized starch gave films that absorbed larger amounts of aqueous fluids. Also, the gel fractions from these saponified gelatinized polymers exhibited higher water swelling, lower shear modulus, and a lower reduced viscosity function (η/cQ). The saponified graft copolymer prepared from gelatinized starch under high dilution conditions more closely resembled those prepared from ungelatinized starch, suggesting that molecular weight of grafted PAN and the grafting frequency rather than starch granule pretreatment might be the most important factor which influences properties.     

PAN-Grafted guaran. II. Short-chain grafting

The room-temperature grafting of polyacrylonitrile (PAN) onto guaran (guar gum) in 2.5 × 10^?3 M aqueous sols or aqueous-methanolic suspensions, initiated by (NH₄)₄ Ce(NO₃)₆ in 1M HNO₃, leads to PAN-branched polysaccharides with graft contents of 11 – 53%. Main chain degradation by treatment with boiling aqueous HCl results in detachment of the PAN side chains, for which number-average molecular masses of ca. 15000 – 48000 are determined viscometrically with the aid of the known Mark-Houwink relationship (K = 3.92 × 10^?4, a = 0.75). Grafting frequencies are in the range of 0.004 – 0.012, equivalent to an average of 80 – 250 non-grafted repeat units for every singly grafted unit in the guaran main chain. The graft copolymers are of interest as precursors of carboxyl-functionalized, water-soluble polysaccharides to serve as polymeric micronutrient and drug carriers of future studies.     

Synthesis and characterization of thienyl‐ and terthienyl‐group‐bearing methacrylic polymers as precursors for grafting reactions of thiophene side‐chains

Acrylic and methacrylic monomers bearing pyrrolyl, thienyl and terthienyl groups, were synthesized and copolymerized with various amounts of butyl acrylate and butyl methacrylate. In the resulting copolymers the heterocycle side‐groups behaved as initiators in the oxidative polymerization of thiophene, allowing the polythiophene chains to grow from the side‐groups and leading therefore to graft copolymers. These last were collected mostly as insoluble fractions after extraction with chloroform. Processible polymers with polythiophene side‐chains were obtained when in the precursor polymer the heterocycle side‐group content was very low. The presence in the graft copolymers of a significant number of stiff polythiophene side‐chains was responsible for the rise in Tg values in comparison with the precursor polymers. The average number of grafted thiophene units, evaluated in the range 2–7.5, did not relate directly to measured conductivity values that were in the range 5.9 × 10⁻⁵–6.2 × 10⁻² S cm⁻¹. © 1999 Society of Chemical Industry     

Synthesis,characterization, and properties of amphiphilic poly(ethyl acrylate) with uniform polyoxyethylene grafts

Amphiphilic copolymers of ethyl acrylate (EA) with uniform polyoxyethylene (PEO) grafts were synthesized by copolymerization of EA with methacrylate terminated PEO macromer in benzene using azobisisobutyronitrile as the initiator. The effects of the molecular weight of the macromers, the charging weight ratio of the macromer to EA, the total monomer concentration, and the amount of initiator on the grafting efficiency (GE) were reported as was the molecular weight of the copolymers. The highest GE reached to above 90% and the molecular weight of the copolymers varied from (5–15) × 10⁴. The reactivity ratio of EA with the macromer was determined to be 0.83. The graft copolymers were purified with extractions and the purified products were characterized with IR, ¹H‐NMR, gel permeation chromatography, differential scanning calorimetry, and membrane osmometry. The average grafting number of the copolymer varied from 2 to 11. The glass‐transition temperature of the poly(EA) in the copolymer was increased because of the partial compatibility of the two components. The crystalline property, emulsifying property, and dilute solution viscosity of the graft copolymers, as well as ionic conductivity of their complexes with alkali metal salts, were studied. The emulsifying volume decreased with the increasing molecular weight of the PEO grafts. The addition of NaOH to the emulsion affected the emulsifying volume only slightly, whereas the addition of HCl changed the oil in water type emulsion into a water in oil type. The conductivity of the LiClO₄ complex of the copolymer with an oxyethylene/Li ratio of 20 reached 3.7 × 10^?5 S/cm at 27°C. The lower the crystallinity of the complex, the higher was the conductivity. The dilute solution viscosity showed the existence of intramolecular microphase separation. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 903–912, 2001     

Grafting of polyacrylonitrile onto guar gum under microwave irradiation

Using microwave (MW) irradiation grafting of polyacrylonitrile (PAN) onto guar gum in water was done without using any radical initiator or catalyst within a very short reaction time. The extent of grafting could be adjusted by controlling the reaction conditions and maximum percentage grafting (%G) of about 188% was obtained under optimum conditions in 1.66 min. The average molecular weight of the grafted PAN chains and water‐retention power of the alkali hydrolyzed MW‐grafted gums were also determined and compared with those of the conventionally synthesized (cs) graft copolymer. A representative MW‐grafted copolymer, guar‐g‐polyacrylonitrile was characterized by IR, NMR, XRD, TGA, and elemental analysis. A plausible mechanism for the grafting under MW was proposed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1569–1575, 2004     

Preparation,characterization, and properties of cellulose–polyacrylamide graft copolymers

Graft copolymers of acrylamide on cellulose materials (α‐cellulose 55.8%, DP 287.3) obtained from Terminalia superba wood meal and its carboxymethylated derivative (DS 0.438) were prepared using a ceric ion initiator and batch polymerization and modified batch polymerization processes. The extent of graft polymer formation was measured in graft level, grafting efficiency, molecular weight of grafted polymer chains, frequency of grafting as a function of the polymerization medium, and initiator and monomer concentrations. It was found that the modified batch polymerization process yielded greater graft polymer formation and that graft copolymerization in aqueous alcohol medium resulted in enhanced levels of grafting and formation of many short grafted polymer chains. Viscosity measurements in aqueous solutions of carboxymethyl cellulose‐g‐polyacrylamide copolymer samples showed that interpositioning of polyacrylamide chains markedly increased the specific viscosity and resistance to biodegradation of the graft copolymers. The flocculation characteristics of the graft copolymers were determined with kaolin suspension. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 913–923, 2003     

Study on preparation and properties of gel polymer electrolytes based on comb-like copolymer matrix of poly(ethylene glycol) monomethylether grafted carboxylated butadiene-acrylonitrile rubber

A novel kind of gel polymer electrolytes (GPE) based on comb-like copolymers of poly(ethylene glycol) monomethylether (mPEG) grafted carboxylated butadiene-acrylonitrile rubber (XNBR) were prepared by introducing ionic liquids and LiClO₄ into polymer framework. FTIR spectra confirmed the grafting of mPEG to XNBR as side chains, and the content of grafted mPEG were calculated from the integral area of related peaks in ¹ H NMR spectra. Such grafted copolymer based GPE with ionic liquids as solvent showed higher ionic conductivity and reached a maximum ionic conductivity of 1.64?×?10^?3?S/cm (30?°C) in the experimental range, because the copolymers performed better polymer chain flexibility, which could be concluded from the decrease of T _g and crystallinity through DSC analysis. The generated GPE exhibited high electrochemical stability and the unit cell of LiFePO₄/GPE/Li could be cycled at room temperature.     

Synthesis and characterization of anionic graft copolymers containing poly(ethylene oxide) grafts

Graft copolymers containing poly(ethylene oxide) side chain attached to maleic anhydride‐alt‐vinyl methyl ether (MA‐VME) copolymer were prepared by coupling MA‐VME and poly(ethylene glycol) monomethyl ether (MPEG) by esterification in DMF at 90°C. MPEG and dodecyl alcohol (DA) were grafted onto MA‐VME copolymer in o‐xylene at 140°C in the presence of p‐toluene sulfonic acid as catalyst. The molecular weights of MPEG were found to influence the rate of the grafting reaction and the final degree of conversion. The graft copolymers were characterized by IR, GPC, and ¹H‐NMR. DSC was used to examine thermal properties of the graft copolymers. The analysis indicates that grafts have phase‐separated morphology with the backbone and the MPEG grafts forming separate phases. The properties in aqueous solutions of these grafts were studied with respect to aggregation behavior and viscometric properties. In aqueous solution, the polymers exhibited polyelectrolyte behavior (i.e., a dramatic increase of the viscosity upon neutralization). Graft copolymers with DA have lower viscosities. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1138–1148, 2002     

Graft copolymers of starch–polyacrylonitrile prepared by ferrous ion–hydrogen peroxide initiation

The effect of concentration, reactant ratios, temperature, and starch pretreatment on grafting of acrylonitrile onto starch were studied. Grafting was efficient at high concentrations (8–12% starch) when granular starch was used. The molecular weights for grafted polyacrylonitrile (PAN) were higher when gelatinized starch was used, but grafting efficiencies (grafted PAN/total PAN) were much lower. The molecular weight of the grafted side chain increased with increased concentration of reactants. The grafting frequency was highest when the reaction mixture was kept at 5°C and decreased with increased swelling of the starch. The starch–polyacrylonitrile graft copolymers were saponified and dried to give products which absorbed 75–440 ml H₂O per gram and 20–70 ml synthetic urine per gram.     

Water-soluble copolymers. I. Synthesis of model dextran-g-polyacrylamides by Fe(II)/H2O2 initiation and characterization by aqueous size exclusion chromatography

Model graft copolymers were synthesized by grafting acrylamide onto dextran (M?_w = 500,000) utilizing the Fe(II)/H₂O₂ initiation system. Aqueous size exclusion chromatography (SEC) was used to determine the effects of changing reaction parameters on hydrodynamic dimensions of the resulting graft copolymers. It was also possible to optimize reaction conditions yielding the highest viscosity graft copolymer with the least amount of homopolyacrylamide and unreacted substrate. The molecular structures of the graft copolymers were determined by elemental analysis, SEC, and solution viscometry. Selective hydrolysis of the dextran backbone allowed determination of average molecular weight of acrylamide grafts, number of grafting sites, and average molecular weight of the graft copolymers. Rheological studies indicated viscosity and pseudoplastic behavior were largely related to the graft length of the polyacrylamide side chains.     

Structure and properties of cellulose graft copolymers. II. Cellulose–styrene graft copolymers synthesized by the ceric ion method

Styrene was graft-copolymerized onto wood cellulose by the ceric ion method of Mino and Kaizerman. The grafting reaction was found to depend strongly on the concentration of ceric ion in the grafting system and maximum grafting occurred in a narrow range of concentration of initiator, 1.0 × 10^?3-1.8 × 10^?3 mol/l, at 58 ± 1°C. A pretreatment technique, developed to enhance the monomer diffusion into cellulose, was found to increase the grafting considerably. The structures of the cellulose-styrene graft copolymers were studied by hydrolyzing away the cellulose backbone to isolate the grafted polystyrene branches. The molecular weight and the molecular weight distributions of the grafted polystyrene were determined using gel permeation chromatography. The number-average molecular weight (M?_n) ranged from 23,000 to 453,000 and the polydispersity ratios (M?_w/M?_n) varied from 2.5 to 8.0. The grafting frequencies calculated from the per cent grafting and molecular weight data were of the order of 0.05–0.4 polystyrene branches per cellulose chain.     

Grafting of N‐carbamyl maleamic acid onto a styrene–butadiene–styrene copolymer

A styrene–butadiene–styrene block copolymer (SBS) was functionalized with N‐carbamyl maleamic acid (NCMA) using two peroxide initiators with the aim of grafting polar groups onto the molecular chains of the polymer. The influence of the concentration of benzoyl peroxide (BPO) and 2,5‐dimethyl, 2,5‐diterbuthylperoxihexane (DBPH) was studied. The concentration of peroxy groups ranged between 0.75 and 6 × 10^?4 mol % while the concentration of NCMA was constant at 1 wt %. The reaction temperature was chosen according to the type of peroxide employed, being 140°C for BPO and 190°C for DBPH. FTIR spectra confirmed that NCMA was grafted onto the SBS macromolecules. It was found that the highest grafting level was achieved at a concentration of peroxy groups of about 3 × 10^?4 mol %. Contact angle measurements were used to characterize the surface of the SBS and modified polymers. The contact angle of water drops decreased with the amount of NCMA grafted from 95°, the one corresponding to the SBS, to about 73°. T‐peel strength of polymer/polyurethane adhesive/polymer joints made with the modified polymers was larger than those prepared with the original SBS. The peel strength of SBS modified with 1.5 and 3 × 10^?4 mol % of peroxy groups from BPO were five times larger than that of the original SBS. The materials modified using BPO showed peel strengths higher than the ones obtained with DBPH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4468–4477, 2006     

Radiation‐induced graft copolymerization of 2‐vinylpyridine and styrene onto isotactic polypropylene fiber

Isotactic polypropylene fiber (IPP) was graft‐copolymerized using 2‐vinyl pyridine (2‐VP) and styrene (sty) as the monomers by the mutual irradiation method in air. The percentage of grafting was determined as a function of various reaction parameters and it was found that the maximum grafting of 2‐VP (114%) and sty (76%) was obtained at an optimum dose of 1.08 × 10⁴ and 0.64 × 10⁴ Gy using 1.8 × 10⁻² mol of 2‐VP and 4.3 × 10⁻² mol of sty, respectively. The graft copolymers were characterized by differential scanning calorimetric analysis and isolation of the grafted chains from the grafted iPP samples. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2959–2969, 1999     

Synthesis,characterization, and properties in aqueous solution of poly(starch-g-[1-amido-ethylene)-co-(sodium 1-(2-methylprop-2N-yl-1-sulfonate)amidoethylene)])

Graft terpolymers of starch, 2-propenamide, and sodium 2-methyl-3-imino-4-oxohex-5-ene-1-sulfonate can be made by cerium-IV-initiated, free-radical polymerization of an aqueous monomer mixture on starch. Synthesis is conducted on aqueous, gelled, lintnerized potato starch at 30°C under a nitrogen atmosphere. Yields range from 50 to 100 wt % and products contain 9–52 wt % starch, 1–51 wt % 1-acidoethylene, and 18–65 wt % sodium 1-(2-methylprop-2N-yl-1-sulfonate)amidoethylene. Repeat unit ratios in the reaction product approximate monomer ratios in the reaction mixture. Fraction of starch grafted in a reaction decreases as the mole fraction of sulfonated monomer in the reaction mixture increases. No proof has been found for grafting of synthetic side chains to starch in monomer mixtures containing only sulfonated monomer. Starch graft copolymers with side chains composed of 1-amidoethylene units and a sulfonated 1-amidoethylene unit derivative, 1-(sodium[2-methylprop-2N-yl-1-sulfonate])amidoethylene, are water-soluble, thickening agents. The rheology of solutions of these copolymers is a function of the ratio of nonsulfonated to sulfonated repeat units in the synthetic chains of the molecule. Aqueous solutions of these products are shear thinning and have power law exponents which decrease 1) with increasing product concentration or 2) as the nonsulfonated to sulfonated repeat unit ratio moves toward 3/1. Limiting viscosity number of product in water decreases with increasing shear rate of measurement or with increasing salt concentration of the solvent. Formulas are derived from the theories of Kirkwood and Flory which show that for copolymers with constant molecular weight, expansion coefficient, and limiting viscosity number increase as the fraction of sulfonate-containing repeat units in the chain increase. This theoretical requirement and the limiting viscosity data for groups of samples prepared under identical synthesis conditions are used to show that molecular weight of the graft copolymer decreases as the fraction of sulfonated repeat units in the copolymer increases. Screen factor measurements show product solutions to be viscoelastic.     

1H-NMR studies on water in methacrylate hydrogels. II

Properties of water in the wet membranes of a random copolymer of methyl methacrylate and methoxy poly(ethylene glycol)–monomethacrylate P(MMA-co-M100G) and of a graft copolymer of vinyl chloride and methoxy poly(ethylene glycol)–monomethacrylate P(VC-g-M100G) membranes were studied by proton NMR spectroscopy. Both polymers contain flexible polyoxyethylene side chains. Temperature and frequency dependences of relaxation times, changes of signal intensity of water protons on freezing and thawing, and saturation transfer were measured for both copolymers. These experimental results revealed that most of the bound water in these copolymers does not exist in a rigid state as suggested for the other hydrogels. The introduction of flexible hydrophilic side chains resulted in high mobility of the water molecules bound to the side chains (the apparent correlation time T_c ～ 10^?10 s). For the graft copolymer P(VC-g-M100G), hydrophilic polyoxyethylene side chains are contiguous to each other. Because of the interaction between the side chains, the mobility became more complex than that for the random copolymer P(MMA-co-M100G). The difference in the mode of mobility of water on the membrane surface may be related to the difference of the membrane characteristics of these copolymers.     

New water-soluble copolymers of 2-methacryloyloxyethyl phosphorylcholine for surface modification

New copolymers of 2-methacryloyloxyethyl phosphorylcholine with 2-Deoxy-2-methacrylamido-D-glucose, N-vinylpyrrolidone, and N-vinyl-N-methylacetamide were synthesized and characterized; the obtained copolymers contained 10–50 mol% of phosphorylcholine moieties, and their molecular masses ranged from 1.05 × 10⁵ to 4.40 × 10⁵. Reactivity ratios of the monomers were estimated. Conformational states of the copolymers in aqueous solutions were studied. The synthesized copolymer was grafted onto the surface of carbon fiber biosorbent using γ-radiation.     

Graft copolymerizations of modified cellulose,grafting of acrylonitrile,and methyl methacrylate on carboxy methyl cellulose

Graft copolymers of acrylonitrile (ACN), methyl methacrylate (MMA), and their mixtures on carboxy methyl cellulose (d.S 0.4–0.5) were prepared by the use of ceric ion initiator in aqueous medium. The graft copolymers were characterized by IR spectroscopy. The extent of graft copolymerization of ACN and MMA was measured in terms of graft level, molecular weight of grafted polymer chains, and the frequency of grafting as functions of ceric ion concentration. It was found that at comparable reaction conditions, the molecular weight of the grafted polymer chains and the frequency of grafting were not of the same order of magnitude. For the monomer mixtures, the copolymer compositions obtained from the total nitrogen contents of the copolymer samples showed that a disproportionately low amount of ACN monomeric units were incorporated into the graft copolymer, even at high ACN content of the feed. © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of temperature‐responsive copolymers based on N‐vinylcaprolactam and their grafting on fibres

BACKGROUND: Responsive materials are able to respond reversibly to an environmental stimulus. When the stimulus is temperature in the physiological range, the responsive material is particularly interesting for textile applications. We describe here the synthesis and characterization of reactive temperature‐responsive copolymers and their subsequent grafting on cotton fabrics. RESULTS: Copolymers of N‐vinylcaprolactam and various reactive monomers were synthesized via free radical polymerization in solution. The copolymers were characterized in terms of chemical structure, molecular weight and temperature‐responsive properties. The copolymer of N‐vinylcaprolactam and methacrylic acid (11 or 22 wt%) and the hydrolysed copolymer of N‐vinylcaprolactam and acryloyl chloride were found to be temperature responsive. They were subsequently grafted on cotton fabrics. The grafting was studied using X‐ray photoelectron spectroscopy and scanning electron microscopy measurements and was found to be effective. Finally, the modified cotton fabrics were found to exhibit temperature‐responsive water regain and water vapour transmission rates. CONCLUSION: Temperature‐responsive copolymers were synthesized, characterized and successfully grafted on cotton fabrics, yielding responsive fabrics. Such fabrics can hence be used to modulate the skin microclimate under textiles. Copyright © 2009 Society of Chemical Industry     

Synthesis of vinylferrocene and the ligand-exchange reaction between its copolymer and carbon nanotubes

To improve the dispersibility of carbon nanotubes (CNTs), poly(vinylferrocene-co-styrene) (poly (Vf-co-St)), was grafted onto the surface of CNTs by a ligand-exchange reaction. Poly(Vf-co-St) was obtained by a radical copolymerization reaction using styrene and vinylferrocene as the monomers. The vinylferrocene was synthesized from ferrocene via a Friedel-Crafts acylation. The molecular weight, molecular weight distribution, and amount of Vf in the poly(Vf-co-St) were 1.32 × 10⁴, 1.69 and 17.6% respectively. The degree of grafting of the copolymer onto the CNTs surface was calculated from thermogravimetric analysis and varied from 27.1% to 79.7%. The addition of the poly(Vf-co-St) greatly promoted the dispersibility of the modified CNTs in anhydrous alcohol. The electrical conductivity of composites prepared from the polymer-grafted CNTs and copolymer (acrylonitrile, 1,3-butadiene and styrene, ABS) strongly depended on the degree of grafting. These results show that the amount of polymer grafted onto the surface of CNTs can be controlled and that the electrical properties of composites prepared with these grafted polymers can be tuned.