纳米ZnO填充的PTFE基复合材料摩擦学性能研究

得胜０００型摩擦磨损试验机研究了不同体积含量的纳米氧化锌（ＺｎＯ）填充的ＰＴＦＥ基复合材料在于摩擦条件下与不风对摩时的摩擦学性能,并利用扫描电子微镜（ＳＥＭ）对ＰＴＦＥ及纳米ＺｎＯ／ＰＴＦＥ复合材料的微观结构、磨损表面和转移膜进行了观察和分析。结果表明,纳米ＺｎＯ／ＰＴＦＥ复合材料的摩擦性能与纯ＰＴＦＥ基本相当,但耐磨性明显优于后者,纳米ＺｎＯ在复合材料中的最佳含量为１５ｖｏｌ．％左右。     

Impact of Viscoelasticity on the Tribological Behavior of PTFE Composites for Valve Seals Application

In this article, we studied and explored the impact of viscoelasticity on the friction and wear behavior of pure polytetrafluoroethylene (PTFE), carbon–graphite PTFE composite, and glass fiber–MoS₂ PTFE composite. Tests were carried out using a specific reciprocating tribometer for valve seal application. The worn surfaces of the PTFE composites and the transfer films formed on the counterface were examined with a scanning electron microscope (SEM). Experimental results revealed that the addition of filler materials was effective in reducing the wear volume in all composites studied. In addition, the friction coefficient and wear resistance showed high sensitivity to the viscoelastic behavior of the PTFE seal. SEM investigation showed that the incorporation of particulate fillers into the PTFE matrix could dramatically reduce and stabilize the transfer films to the counterface, so they largely decreased the wear of the PTFE composites.     

MoS2、CdO及聚全氟乙丙烯填充改性聚四氟乙烯复合材料的摩擦磨损性能

用机械共混、冷压成型自由烧结的方法制备了MoS2、CdO和聚全氟乙丙烯填充聚四氟乙烯复合材料;用MM-2000型摩擦磨损试验机测试了在干摩擦条件下该复合材料的摩擦磨损性能;用扫描电镜(SEM)对磨损试样的表面形貌进行观察和分析.结果表明:未添加聚全氟乙丙烯的复合材料其摩擦磨损性能比添加的好;当CdO的体积分数为22.5%,MoS2的体积分数为7.5%时,复合材料的摩擦因数最小,抗磨性强,复合材料的摩擦磨损性能最佳.     

聚苯酯填充聚四氟乙烯复合材料摩擦学行为研究

采用聚苯酯（Ekonol）、Ekonol／PAB纤维增强聚四氟乙烯（PTFE）制备利用转移膜润滑的摩擦副材料，并研究了两组材料在于摩擦条件下与9Cr18轴承钢对摩时的摩擦学性能；运用扫描电镜分析了两组材料磨损表面形貌和磨损机理。结果表明：随着Ekonol含量的增大，Ekonol填充PTFE复合材料的摩擦因数逐渐增大，当Ekonol质量分数超过25％时摩擦因数略有下降，磨损方式由以犁削磨损为主转变为以疲劳磨损为主；而Ekonol／PAB纤维填充门FE复合材料的摩擦因数，随Ekonol含量的增大而增大，磨损方式由以粘着磨损为主转变为以疲劳磨损为主。Ekonol／PAB纤维填充PTFE复合材料的摩擦学性能优于Ekonol填充PTFE复合材料。     

Friction and wear properties of metal powder filled PTFE composites under oil lubricated conditions

Four kinds of polytetrafluoroethylene (PTFE)-based composite, pure PTFE, PTFE+30vol.%Cu, PTFE+30vol.%Pb and PTFE+30vol.%Ni composite, were prepared. The friction and wear properties of these metal powder filled PTFE composites sliding against GCr15 bearing steel under both dry and lubricated conditions were studied using an MHK-500 ring-block wear tester. The worn surfaces of the PTFE composites and the transfer films formed on the surface of GCr15 bearing steel were examined using scanning electron microscopy (SEM) and optical microscopy respectively. Experimental results show that the friction and wear properties of the PTFE composites can be greatly improved by liquid paraffin lubrication. The wear of these PTFE composites can be decreased by at least 1 to 2 orders of magnitude compared with that under dry friction conditions, while the friction coefficients can be decreased by 1 order of magnitude, SEM and optical microscopy investigations of the rubbing surfaces show that metal fillers of Cu, Pb and Ni not only raise the load carrying capacity of the PTFE composites, but also promote transfer of the PTFE composites onto the counterfaces, so they greatly reduce the wear of the PTFE composites. However, the transfer of these PTFE composites onto the counterfaces can be greatly reduced by liquid paraffin lubrication, but transfer still takes place.     

PTFE对纤维增强尼龙66材料摩擦学性能的影响

考察了玻璃纤维（GF）增强尼龙66复合材料的摩擦磨损性能,以及PTFE对复合材料摩擦学性能的影响,利用扫描电镜分析了磨损形貌。结果表明：15％GF增强尼龙复合材料的摩擦学性能改善不明显,而且磨损量高于纯尼龙;加入PTFE在摩擦过程中形成了转移膜,降低了玻璃纤维增强尼龙复合材料的摩擦磨损,改善了其摩擦学性能。     

Ekonol/石墨/MoS2填料对PTFE力学和摩擦磨损性能的影响

研究了Ekonol含量对Ekonol／石墨／MoS2／P，PTFE复合材料的力学性能、摩擦磨损性能的影响，以及滑动速度、载荷对材料摩擦磨损性能的影响；用扫描电子显微镜观察了复合材料磨损后的表面形貌，并探讨了其磨损机制。结果表明：加入填料降低了材料的拉伸强度和弯曲强度，但提高了弯曲模量和硬度；同时填料能提高材料的磨损性能，但使摩擦因数升高了；当Ekonol含量较低时，磨损机制为粘着磨损，随着填料含量的增加，Ekonol分散到基体中，起到了承载作用，阻止了PTFE基体的带状破坏，磨损机制为疲劳磨损和轻微的粘着磨损；摩擦因数随载荷的增大而减小，随滑动速度的增大而增大，在相同的滑动时间内，磨痕宽度随载荷和滑动速度的增大而增大。     

SiCp增强铝基复合材料与Kevlar增强摩擦材料摩擦副摩擦磨损机理研究

采用盘销式摩擦磨损试验机，对SiCp含量为20vol％的铝基复合材料和Kevlar增强摩擦材料组成的摩擦副在于摩擦条件下的摩擦磨损机理进行了实验研究。结果表明：摩擦副在跑合过程中，铝基复合材料中的SiCp颗粒对较软的有机复合材料产生犁削和微观切削效应，磨损机理为铝基复合材料的硬质颗粒对较软的有机复合材料的磨粒磨损；在跑合后的磨损试验中，摩擦材料磨损表面呈现出粘着磨损和塑性变形特征，随着转动速度的增加，塑性流动加剧；摩擦副接触表面发生材料的相互转移，并在铝基复合材料表面形成转移膜，且在较高速度下转移膜更易形成；在高速条件下，摩擦材料表面可见从铝基复合材料的铝合金基体中脱离的SiCp颗粒和熔融迹象；摩擦材料的磨损机理主要为磨粒磨损、粘着磨损和塑性变形。     

Tribological behaviour of PTFE modified cotton polyester composites

Abstract

An attempt on modification of tribological behaviour of cotton polyester composite was done with polytetrafluoroethylene (PTFE). PTFE modified polyester–cotton composites were developed and studied for their friction and sliding wear behaviour at different applied loads. The sliding wear tests of composites were conducted against EN-31 steel counter face. The coefficient of friction μ as well as the sliding wear rate of cotton–polyester composites reduced significantly on addition of PTFE. The reduction in wear rate of PTFE modified polyester–cotton composite has been discussed with the help of SEM observations of worn surfaces and coefficient of friction.     

聚四氟乙烯填充含量对钢背超高分子量聚乙烯纤维织物复合材料摩擦学性能的影响

为改善广泛应用于船舶苛刻环境无油/脂润滑摩擦配副材料的摩擦学性能,将聚四氟乙烯（PTFE）按不同质量分数与钢背超高分子量聚乙烯纤维织物复合材料结合,研究它与45钢盘在变转速环环端面干摩擦状态下的摩擦学特性。对试验过程中摩擦因数及磨损量进行测量,利用表面轮廓仪、扫描电子显微镜与超景深显微镜对复合材料及对磨件磨损表面形貌进行了观察与分析。结果表明：所有填充PTFE的复合材料摩擦学性能均表现优异,随着PTFE含量的增加,复合材料摩擦性能变差,其中1 %（质量分数） PTFE填充复合材料综合摩擦性能最好,在试验工况下主要发生磨粒磨损,PTFE填充量较高的复合材料在高速下由于团聚及摩擦热量积聚主要经历黏着磨损与疲劳磨损。     

Tribological Behaviors of Hybrid PTFE/Nomex Fabric/Phenolic Composite under Dry and Water-Bathed Sliding Conditions

The tribological behaviors of hybrid polytetrafluoroethylene (PTFE)/Nomex fabric/phenolic composite under dry sliding condition and water-bathed sliding conditions were investigated using a pin-on-disk type tribometer. The results showed that this hybrid fabric reinforced composite exhibited a higher wear rate and a lower friction coefficient under water-bathed sliding conditions compared to that measured under dry sliding condition. Scanning electron microscopy (SEM) and X-ray photoelectron microscopy (XPS) analysis demonstrated that under water-bathed sliding conditions the transfer films formed on the counterpart pins surface were of high roughness and less PTFE transferred onto the pin surface, compared to that under dry sliding condition. Moreover, the hybrid fabric composite displayed varied tribological behaviors when distilled water-bathed sliding condition and seawater-bathed sliding condition were applied separately.     

On the friction and wear behavior of PTFE composite filled with rare earths treated carbon fibers under oil-lubricated condition

Carbon fibers (CF) were surface treated with air-oxidation, air-oxidation followed by rare earths (RE) treatment and RE treatment, respectively. The friction and wear properties of the polytetrafluoroethylene (PTFE) composites filled with differently surface treated carbon fibers, sliding against GCr15 steel under oil lubrication, were investigated on a reciprocating ball-on-disk UMT-2MT tribometer. The worn surfaces of the PTFE composites were examined using a scanning electron microscopy (SEM). Experimental results revealed that surface treatment of carbon fibers reduced the wear of CF-reinforced PTFE composites. Among all the treatments to carbon fibers, RE treatment was the most effective and lowest friction and wear rate of CF-reinforced PTFE composite was exhibited, owing to the effective improvement of the interfacial adhesion between the carbon fibers and PTFE matrix.     

Friction and wear characteristics of lead and its compounds filled polytetrafluoroethylene composites under oil lubricated conditions

The friction and wear properties of Pb, PbO, Pb₃O₄, or PbS filled polytetrafluoroethylene (PTFE) composites sliding against GCr15 bearing steel under both dry and liquid paraffin lubricated conditions were studied by using an MHK-500 ring-block wear tester. The worn surfaces and the transfer films of these PTFE composites formed on the surface of GCr15 bearing steel were then investigated by using a scanning electron microscope (SEM) and an optical microscope, respectively. Experimental results show that filling Pb, PbO, Pb₃O₄ or PbS to PTFE can greatly reduce the wear of the PTFE composites, but the wear reducing action of Pb₃O₄ is the most effective. Meanwhile, PbS increases the friction coefficient of the PTFE composite, but Pb and Pb₃O₄ reduce the friction coefficients of the PTFE composites. However, the friction and wear properties of lead or its compounds filled PTFE composites can be greatly improved by lubrication with liquid paraffin, and the friction coefficients of the PTFE composites can be decreased by one order of magnitude. Optical microscope investigation of transfer films shows that Pb, PbO, Pb₃O₄ and PbS enhance the adhesion of the transfer films to the surface of GCr15 bearing steel, so they greatly reduce the wear of the PTFE composites. However, the transfer of the PTFE composites onto the surface of GCr15 bearing steel can be greatly reduced by lubrication with liquid paraffin, but the transfer still takes place. SEM examination of worn surfaces shows that the interaction between liquid paraffin and the PTFE composites creates some cracks on the worn surfaces of the PTFE composites; the creation and development of the cracks reduces the load-carrying capacity of the PTFE composites, and this leads to deterioration of the friction and wear properties of the PTFE composites filled with lead or its compounds under higher loads in liquid paraffin lubrication.     

Wear and friction behavior of sand cast brake rotor made of A359-20 vol% SiC particle composites sliding against automobile friction material

The effect of load range of 30-100 N and speed range of 3-12 m/s on the wear and friction behavior of sand cast brake rotor made of A359-20 vol% SiC particle composites sliding against automobile friction material was investigated. Dry sliding frictional and wear behavior were investigated in a pin-on-disc type apparatus. Automobile friction material was used as pin, while the A359-20 vol% SiC particle composites formed the rotating disc. For comparison, the wear and friction behavior of commercially used cast iron brake rotor were studied. The results showed that the wear rate of the composite disc decreased with increasing the applied load from 30 to 50 N and increased with increasing the load from 50 to100 N. However, the wear rate of the composite disc decreased with increasing the sliding speed at all levels of load applied in the present work. For all sliding speeds, the friction coefficient of the composite disc decreased with applied load. The worn surfaces as well as wear debris were studied using scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analyzer and X-ray diffraction (XRD) technique. At load of 50 N and speed range of 3-12 m/s, the worn surface of the composite disc showed a dark adherent layer, which mostly consisted of constituents of the friction material. This layer acted as a protective coating and lubricant, resulting in an improvement in the wear resistance of the composite.     

热压Ni-MoS2自润滑复合材料在不同温度的往复摩擦磨损特性

采用自润滑复合材料,对提高某些机械摩擦副的使用寿命有很显著的效果。研究了热压Ni-MoS2自润滑复合材料与GCr15钢球组成的点接触配对副,在室温和高温条件下进行微幅往复摩擦运动时的自润滑特性。考察了载荷、温度及MoS2含量对摩擦系数和磨损率的影响,并借助扫描电镜观察磨损表面的形貌特征。结果表明：摩擦系数随载荷增加而不断提高;温度在400℃以下时,摩擦系数能保持较低数值;在室温和250℃时,含60%MoS2的复合材料均具有最低磨损率;提高MoS2含量有助于改善高温自润滑性;MoS2转移润滑膜的完整程度可作为Ni-MoS2复合材料自润滑性能好坏的判据。     

Preliminary studies of the influence of cryo‐treatment on the mechanical and tribological properties of ptfe and composites

Cryogenic treatment of polytetrafluoroethylene (PTFE) has proved beneficial in improving the abrasive wear resistance of several polymers, and it was thus assessed in an adhesive wear mode, as well. Preliminary investigations on the effect of cryogenic treatment on the tribological properties, in adhesive wear mode, and mechanical properties of neat PTFE and it composites filled with bronze or short glass fibres (GF) were carried out. It was found that, although the improvement in the wear and friction performance of neat PTFE and a GF + PTFE composite was significant, no such positive effect was observed for the bronze + PTFE composite. On the contrary, this composite showed a deterioration in performance. The reason behind the improvement in the tribological behaviour of neat PTFE and the GF + PTFE composite could not be clearly understood. However, it was confirmed that, if the treatment adversely affected the mechanical properties, then the tribological performance also deteriorated. An examination of the worn surface of the material and the counterface disc using a scanning electron microscope revealed changes in the microstructure due to the treatment. It was also confirmed from these SEM studies that the compatibility of bronze and PTFE was very poor, which led to poor performance of the composite both in the untreated and the cryo‐treated form. Further detailed investigation and analysis of various materials and composites, however, are necessary to establish the utility of this technique.     

The tribological characteristics of JS material under lubrication of oil

A material composed of a steel backing, a sintered porous bronze middle layer and a layer of reinforced PTFE, which is named JS material, was prepared. The friction, wear and limiting PV values of this material under dry friction as well as the lubrication of number 20 mechanical oil were studied using a MPV-1500 friction tester. The worn surface of JS material and the transfer film formed on the counterface of carbon steel were investigated using scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). The results show that the friction, wear and limiting PV values of JS material can be greatly improved with the lubrication of oil. The results of SEM and EPMA analyses indicate that, under dry friction conditions, the solid lubricant PTFE and Pb easily transfer to the steel counterface and results in the reduction of friction and wear; while under the lubrication of oil, little transference of PTFE and Pb to the steel surface occurs and very small friction and wear are achieved. Analyses of frictional surfaces also suggest that the Pb filler gets enrichment on the rubbing surfaces, which is beneficial in increasing the adhesion of the transfer film with the steel surface.     

Tribological behaviour of modified polyacetal against MC nylon without lubrication

Compared with other polymers, polyacetal or polyoxymethylene (POM) which is widely used as bearing, guide, gear and other sliding parts, has high strength and stiffness, excellent chemical resistance and superior antifriction and wear resistance. To improve the toughness and self‐lubrication capacity of POM due to its higher crystallizability, other components, which include toughening phase and solid lubricants, are often added to the POM matrix. This paper deals with the friction and wear behaviours of POM which was modified by the toughening phase polyurethane (PU) and filled with polytetrafluoroethylene (PTFE) and silicone oil, during rubbing against MC nylon without liquid lubrication. Friction and wear tests show the tribological performance of the modified POM (M‐POM) with 10 wt% PU is better than those of pure POM and POM blended with PTFE under dry friction. The frictional coefficient of the M‐POM decreases with increasing nominal load. The sliding velocity has a more obvious effect on the tribological properties of the M‐POM than the nominal load. The higher sliding velocity leads to thermal degradation and melting of the experimental polymers because of the frictional heat. This revised version was published online in June 2006 with corrections to the Cover Date.     

石墨填充聚四氟乙烯基复合材料的摩擦学性能

为了研制PTFE基粘弹-摩擦型阻尼材料,采用机械共混-冷压成型-烧结的工艺制备了石墨、聚苯硫醚、聚醚醚酮混合填充PTFE基复合材料,利用环-块式磨损试验机,在干摩擦条件下考察了复合材料的摩擦学性能,并用扫描电镜观察了磨损表面形貌,研究了复合材料的磨损机制。结果表明:PTFE含量不同的复合材料,随石墨填充量的增大,摩擦因数和磨损率的变化趋势不同,磨损主要由犁削、粘着和疲劳剥落中的一种或几种引起;适当配比的PTFE基复合材料具有较好的摩擦阻尼性能,能够满足粘弹-摩擦阻尼材料的要求。     

纳米金属粉填充Ekonol/PTFE复合材料的摩擦磨损性能研究

评价了分别用不同体积含量的纳米镍粉和纳米铜粉填充聚苯酯/聚四氟乙烯(Ekonol/PTFE)复合材料体系的力学性能,利用M-200型磨损试验机研究了纳米Ni、纳米Cu含量对Ekonol/PTFE复合材料摩擦学性能的影响,借助扫描电子显微镜和能谱分析手段考察试样磨损表面和磨屑,并探讨其摩擦磨损机制。结果表明,纳米Ni能在一定范围内增加Ekonol/PTFE复合材料的冲击强度;纳米金属粉填入量较小时均能增加复合材料的洛氏硬度。纳米Ni与纳米Cu均能增加Ekonol/PTFE复合材料的摩擦因数并降低磨损率。其原因在于纳米金属粉在复合材料摩擦表面富集,通过金属分子间的吸引作用,增大复合材料的摩擦因数。