Dry sliding wear behaviour of aluminium–lithium alloys reinforced with SiC particles

Several wear tests were carried out at different pressures and temperatures on Al-8090 and Al-8090 + 15 vol.% SiC_p. Worn specimens and debris were also examined using SEM and EDX techniques to identify the dominant wear mechanisms. Wear rate increases about two orders of magnitude when temperature is above a critical one. The transition from mild to severe wear is dependent on nominal pressure. The composite transition temperature is higher than that of the unreinforced alloy. Within the mild wear regime, the wear rates for both materials exhibit a minimum over 100 °C and are higher for the composite material than for the Al-8090 below the transition temperature. It has been also observed that the presence of mechanically mixed layers (MML) on the wear surface with varying morphology and thickness influenced the wear rate. The morphology and composition of the wear debris also change with the wear mechanism.     

The tribological characteristics of TiCN coating at elevated temperatures

The tribological behaviour of TiCN coating prepared by unbalanced magnetron sputtering is studied in this work. The substrates made from austenitic steel were coated by TiCN coatings during one deposition. The measurements were provided by high temperature tribometer (pin-on-disc, CSM Instruments) allowing measuring the dependency of friction coefficient on cycles (sliding distance) up to 500 °C. The evolution of the friction coefficient with the cycles was measured under different conditions, such as temperature or sliding speed and the wear rate of the ball and coating were evaluated. The 100Cr6 balls and the Si₃N₄ ceramic balls were used as counter-parts. The former were used at temperatures up to 200 °C, the latter up to 500 °C. The wear tracks were examined by optical methods and SEM. The surface oxidation at elevated temperatures and profile elements composition of the wear track were also measured.The experiments have shown considerable dependency of TiCN tribological parameters on temperature. Rise in temperature increased both friction coefficient and the wear rate of the coating in case of 100Cr6 balls. The main wear mechanism was a mild wear at temperatures up to 200 °C; fracture and delamination were dominating wear mechanisms at temperatures from 300 to 500 °C.     

Effect of three nitriding treatments on tribological performance of 42CrAlMo7 steel in boundary lubrication

Evolution of friction and wear of 42CrAlMo7 steels with different nitriding processes was investigated during boundary-lubricated rolling–sliding tests. The wear behaviour of nitrided steel with a thin compound layer (produced by plasma nitriding and by gas nitriding followed by oxidation) was characterised by the early removal of the compound layer, and the wear resistance was thus, given by the underlying diffusion layer. In the case of the material with a thick compound layer (produced by gas nitriding) wear was restricted to the compound layer. In this material, at low applied load (300 N, i.e. 485 MPa of Hertzian pressure, in this work), after the removal of the external porous layer wear tended to be negligible. At high applied load (1000 N, 890 MPa), on the other hand, the wear rate became higher than that of the diffusion layer. The friction behaviour was followed by determining the λ-factor evolution during each test. For a given λ-factor, the friction coefficients at 300 N were lower than at 1000 N.     

Synthesis of boride coatings on steel using plasma transferred arc (PTA) process and its wear performance

Boriding of the surface of a tool steel using boron powder and the plasma transferred arc process was investigated. It was shown that this method is an easy and effective technique in producing uniform alloyed layers with a thickness of about 1.5 mm and a hardness between 1000 and 1300 HV.The microstructure of the borided surfaces consists of primary Fe₂B-type borides and a eutectic mixture of borides and martensite. Some cracks are observed in the eutectic regions but they do not seem to critically affect the behaviour of the coatings in sliding wear.The wear rate of pin on disc tests is primarily affected by the applied load and it lies between 10⁻⁵ mm³/m for low loads and 10⁻² mm³/m for high loads. Two distinct regimes of mild and severe wear are obtained separated by a critical load. Mild wear is due to the load supporting effect of borides and severe wear is due to their breakage above a critical load. The wear rate is not significantly affected by the sliding velocity and is consistent with the friction coefficient.The friction coefficient varies from 0.13 to 0.23 and depends strongly on the oxidation status of the wear track. The sliding velocity affects the sliding distance where the coefficient of friction reaches equilibrium.     

Evolution of wear,roughness, and friction of Alloy 600 superalloy surfaces in water-submersed sliding

Self-mated wear and friction of Alloy 600 superalloy was studied in a water-submersed ring-on-rod configuration, loading the side of a 6.35 mm diameter rod across the flat surface of a rotating annular ring of 100 mm outer diameter and 70 mm inner diameter producing two sliding contacts along the ring. Tests were conducted at sliding speeds of 0.178 and 0.330 m/s for sliding distances of 100 m. Normal loads of 51 and 204 N were applied, and initial R_a surface roughnesses of the rings along the sliding direction were either smooth (～0.2 μm) or rough (～7.5 μm). Increased initial ring roughness caused a ～20-fold increase in rod wear at the lighter load, whereas at the heavier load increased initial roughness only caused a ～4-fold increase in wear. At lower initial ring roughness the 4-fold decrease in normal load caused a large (one order-of-magnitude) decrease in rod wear, whereas for rings of higher initial roughness the 4-fold decrease in normal load caused only minor (2-fold or less) decreases in rod wear. Wear during this 100 m sliding distance only experienced a minor effect from the 1.8-fold change in sliding speed, as did friction. In all cases friction coefficient rapidly settled into the range 0.6–0.7, except in the cases of lower load on rings of lower initial roughness where friction coefficient remained above 1 for most of this sliding duration. At this lower load the initial ～0.2 μm rod roughnesses increased to nearly 0.8 μm by the 100 m sliding distance, whereas at the higher load this same sliding distance resulted in roughnesses returning near to the initial 0.2 μm. It was hypothesized more highly loaded cases also went through initial roughening prior to smoothening back to 0.2 μm roughness within the 100 m sliding distance, and given additional sliding the more lightly loaded cases would also experience subsequent smoothening. Increasing sliding distance to 400 m, roughnesses indicated a smoothening back to 0.2 μm level during those lightly loaded tests, with friction coefficient correspondingly dropping from 1 into the 0.6–0.7 range observed in all other cases. Extended sliding to 400 m at light loading against rings of lower initial roughness also allowed a rod wear rate which increased with increased sliding distance to be observed, approaching the same rate observed against initially rough rings within the 100 m sliding distance.     

Friction and wear properties of αFeSi2–Si alloy,ReSi1.8 and MoSi2 in ethyl alcohol

In this study, Fe–X at% Si alloy (X=70.5, 80.0 and 96.0), Re–64.3 at% Si and Mo–66.7 at% Si disk specimens were prepared by spark plasma sintering, and their friction and wear properties were investigated when they were slid against Si₃N₄ ball specimens in ethyl alcohol. The friction and wear properties of Si ingots were also examined. Fe–70.5 at% Si, Fe–80.0 at% Si, Fe–96.0 at% Si and Re–64.3 at% Si disk specimens exhibited friction coefficients as low as 0.15. It is considered that the low friction of the Fe–70.5 at% Si, Fe–80.5 at% Si and Fe–96.0 at% Si disk specimens was due to the formation of low friction silicon alkoxide and polyoxysilane on the worn surfaces of the disk specimens and the paired ball specimens. Re–64.3 at% Si disk specimens exhibited the highest microvickers hardness of all the disk specimens prepared in this study. In addition, the microvickers hardness of the Fe–X at% Si (X=70.5, 80.0, 96.0 and 100) disk specimen increased with increasing the Si content. Moreover, it was difficult to obtain dense Fe–90.0 at% Si disk specimens by sintering the annealed and crushed Fe–90.0 at% Si powder. However, dense Fe–96.0 at% Si disk specimens could be obtained by sintering the Fe–90.0 at% Si powder at 1403 K.     

Tribological properties of Fe7Mo6-based-alloy lubricated with poly-alpha-olefin containing PN additive

Tribological properties of Fe–Mo type disk specimens were investigated against ASTM 52100 steel balls under the lubrication of poly-alpha-olefin (PAO) and PAO containing 1.5 mass% alkyl-phosphonic acid-triazole-methanamine (PN additive). Both the Fe₇Mo₆-based alloy and Mo disk specimens exhibited lower friction and lower wear rates than the Fe and gray cast iron disk specimens under the lubrication of PAO. The friction coefficients of the Fe₇Mo₆-based alloy disk specimens were reduced to 0.07 by adding 1.5 mass% PN additive to PAO. No wear volume loss was observed on the Fe₇Mo₆-based alloy disk specimens when they were lubricated with PAO containing 1.5 mass% PN additive.     

WC–ZrO2 composites: processing and unlubricated tribological properties

In the present work, we report the processing and properties of WC–6 wt.% ZrO₂ composites, densified using the pressureless sintering route. The densification of the WC–ZrO₂ composites was carried out in the temperature range of 1500–1700 °C with varying time (1–3 h) in vacuum. The experimental results indicate that significantly high hardness of 22–23 GPa and moderate fracture toughness of ∼5 MPa m^1/2 can be obtained with 2 mol% Y-stabilized ZrO₂ sinter-additive, sintered at 1600 °C for 3 h. Furthermore, the friction and wear behavior of optimized WC–ZrO₂ composite is investigated on a fretting mode I wear tester. The tribological results reveal that a moderate coefficient of friction in the range from 0.15 to 0.5 can be achieved with the optimised composite. An important observation is that a transition in friction and wear with load is noted. The dominant mechanisms of material removal appear to be tribochemical wear and spalling of tribolayer.     

Effect of SiC particles on the friction and wear behavior of Ti3Si(Al)C2-based composites

The non-lubricated, sliding friction and wear behavior of Ti₃Si(Al)C₂ and SiC-reinforced Ti₃Si(Al)C₂ composites against AISI 52100 bearing steel ball were investigated using a ball-on-flat, reciprocating tribometer at room temperature. The contact load was varied from 5 to 20 N. For monolithic Ti₃Si(Al)C₂, high friction coefficients between 0.61 and 0.90 and wear rates between 1.79 × 10⁻³ and 2.68 × 10⁻³ mm³ (N m)⁻¹ were measured. With increasing SiC content in the composites, both the friction coefficients and the wear rates were significantly decreased. The friction coefficients reduced to a value between 0.38 and 0.50, and the wear rates to between 2.64 × 10⁻⁴ and 1.93 × 10⁻⁵ mm³ (N m)⁻¹ when the SiC content ranged from 10 to 30 vol.%. The enhanced wear resistance of Ti₃Si(Al)C₂ is mainly attributed to the facts that the hard SiC particles inhibit the plastic deformation and fracture of the soft matrix, the oxide debris lubricate the counterpair, and the wear mode converts from adhesive wear to abrasive wear during dry sliding.     

Wear of aligned silicon nitride under dry sliding conditions

The wear behaviour of textured silicon nitride (Si₃N₄) ceramics with aligned microstructures was analyzed under abrasive wear conditions. Dry reciprocating self-mated ball-on-flat wear tests were performed to study the influence of different microstructural plane/orientation combinations on the Si₃N₄ tribological behaviour. Textured materials showed superior wear resistance than non-textured reference Si₃N₄ for the whole range of loads and contact pressures, 5–50 N and 1.7–3.6 GPa, respectively, with an increase of about 70% for the maximum applied load. Within textured materials, the plane perpendicular to the extruding direction exhibited a 50% higher wear resistance (4 × 10^?5 mm³ N^?1 m^?1) than the parallel plane where the elongated grains were aligned. The severe wear process involved debonding, fracture and debris formation mechanisms. The progress of this sequence depended on the particular microstructure of each plane/orientation combination. A relationship between abrasive wear resistance and selected microstructural parameters has been established.     

Tribological characterization of tungsten nitride coatings deposited by reactive magnetron sputtering

The structure, hardness, friction and wear of tungsten nitrides prepared by d.c. reactive magnetron sputtering were investigated. The coatings were deposited with different nitrogen to argon ratios; the total pressure was kept constant. The tribological tests were performed on a pin-on-disc tribometer in terrestrial atmosphere with 100Cr6 steel, Al₂O₃ and Si₃N₄ balls as sliding counter-bodies. The wear tracks, the ball-wear scars and the wear debris were analysed by scanning electron microscopy in order to characterize the dominant wear mechanisms.The coatings exhibited different phases as a function of the nitrogen content: films with low N content exhibited the α-W phase; β-W phase was dominant for nitrogen contents from 12 to 15 at.% and β-W₂N was observed for nitrogen content higher that 30 at.%. The mechanical and tribological properties of the tungsten nitride coatings were strongly influenced by the structure. The hardness and the Young's modulus values were in the ranges (29–39 GPa) and (300–390 GPa), respectively; the lowest values correspond to the coatings with the highest nitrogen content. Generally, the friction and wear rate of tungsten nitride coatings sliding against ceramic balls increased with nitrogen content reaching a maximum at 12 at.%; further increase of the nitrogen content led to a decrease of the friction and wear. The sliding with the steel balls did not wear the coatings under the selected testing conditions.     

Wear behavior of electroless Ni–P–B4C composite coatings

In this research, the wear of electroless Ni–P and Ni–P–B₄C composite coatings was reviewed. Auto catalytic reduction of Ni in nickel sulfate and sodium hypophosphate bath including suspended B₄C particles with different concentration was used to create composite coatings with 12, 18, 25 and 33 vol.% of B₄C particles. Coatings 35 μm thick were heat treated at 400 °C for one hour in an argon atmosphere and the wear resistance and friction coefficient of heat-treated samples were determined by block-on-ring tests. All wear tests were carried out at 24 °C, 35% moisture, 0.164 m/s sliding speed and about 1000 m sliding distance. Graphs show that an electroless Ni–P–B₄C composite coating with 25 vol.% of B₄C had the best wear resistance against a CK45 steel counterface.     

Tribological properties of solid lubricants (graphite,Sb2S3, MoS2) for automotive brake friction materials

The effect of three different solid lubricants (graphite, Sb₂S₃, and MoS₂) in the brake friction material on various aspects of friction characteristics was investigated. Three friction material specimens were produced based on an experimental formulation, and they contained 10 vol.% graphite, 7 vol.% graphite + 3 vol.% Sb₂S₃, and 7 vol.% graphite + 3 vol.% MoS₂, respectively, fixing the composition of other ingredients. Tribological properties of the friction materials were obtained using a brake dynamometer. Results showed that the friction materials containing Sb₂S₃ and graphite improved friction stability and fade resistance. The friction materials with Sb₂S₃ and MoS₂, on the other hand, exhibited disadvantages in terms of wear resistance, anti-fading, and DTV (disk thickness variation) generation.     

Friction and wear behaviors of C/C-SiC composites containing Ti3SiC2

In the present paper, friction and wear behaviors of a carbon fiber reinforced carbon–silicon carbide–titanium silicon carbide (C-SiC–Ti₃SiC₂) hybrid matrix composites fabricated by slurry infiltration and liquid silicon infiltration were studied for potential application as brake materials. The properties were compared with those of C/C-SiC composites. The composites containing Ti₃SiC₂ had not only higher friction stability coefficient but also much higher wear resistance than C/C-SiC composites. At an initial braking speed of 28 m/s under 0.8 MPa pressure, the weight wear rate of the composites containing 5 vol% Ti₃SiC₂ was 5.55 mg/cycle, which was only one-third of C/C-SiC composites. Self-lubricious film-like debris was formed on the composites containing Ti₃SiC₂, leading to the improvement of friction and wear properties. The effect of braking speed and braking pressure on the tribological properties of modified composites were investigated. The average friction coefficient was significantly affected by braking speed and braking pressure, but the wear rate was less affected by braking pressure.     

Tribological behaviour of human enamel in red wine and apple juice environments

The aim of this study was to investigate wear and friction behaviour of enamel in red wine and apple juice environments at different concentrations and pH in distilled water. Enamel specimens were prepared from freshly extracted human teeth. Dispersalloy amalgam was used to prepare a counterface. A modified pin-on-disc wear machine was employed, and wear tests were carried out under cyclic loading with a mean of 35 N and amplitude of 25 N. The machine simulated tooth wear for 3 h. Two groups of 19 samples were subjected to wear in red wine and apple juice solutions in distilled water, at volumetric concentration ranging from 5 to 95%. The worn enamel surfaces were examined by SEM. Comparative studies of Ca/P ratio before and after testing were performed by means of EDS. The wear rates of enamel varied significantly with pH (p < 0.05) and some pH thresholds have been found. For pH values beyond 3.25 for red wine and 3.52 for apple juice solutions the wear rates were mild and relatively stable. With decreasing pH below the threshold mean wear rates significantly increased and a large extent of measurements could be observed. The results also showed that the wear rate corresponded with surface topography, i.e. different wear rates were accompanied by different wear mechanisms. Simultaneous mechanical and chemical actions occurring during sliding enamel against an amalgam counterface in a drink environment caused different wear behaviour of enamel, which substantially depended on environmental pH.     

Mechanical and unlubricated tribological properties of titanium-containing diamond-like carbon coatings

Titanium-containing diamond-like carbon (Ti-DLC) coatings were deposited on steel with a close-field unbalanced magnetron sputtering in a mixed argon/acetylene atmosphere. The morphology and structure of Ti-DLC coatings were investigated by scanning electron microscopy, transmission electron microscopy, atomic force microscopy and Raman spectroscopy. Nanoindentation, nanoscratch and unlubricated wear tests were carried out to evaluate the hardness, adhesive and tribological properties of Ti-DLC coatings. Electron microscopic observations demonstrated the presence of titanium-rich nanoscale regions surrounded by amorphous carbon structures in Ti-DLC coating. The Ti-DLC coatings exhibit friction coefficients of 0.12–0.25 and wear rates of 1.82 × 10^?9 to 4.29 × 10^?8 mm³/Nm, depending on the counterfaces, sliding speed and temperature. The Ti-DLC/alumina tribo-pair shows a lower friction coefficient than the Ti-DLC/steel tribo-pair under the identical wear conditions. Increasing the test temperature from room temperature to 200 °C reduces the coefficient of friction and, however, clearly increases the wear rate of Ti-DLC coatings. Different wear mechanisms, such as surface polishing, delamination and tribo-chemical reactions, were found in the tribo-contact areas, depending on different wear conditions.     

Comparison of self-mated hardmetal coatings under dry sliding conditions up to 600 °C

Hardmetal coatings prepared by high velocity oxy-fuel (HVOF) spraying represent an advanced solution for surface protection against wear. In the current systematic study the high-temperature oxidation and unidirectional sliding wear in dry and lubricated conditions were studied. Results for a series of experiments on self-mated pairs in dry conditions as part of that work are described in this paper. Coatings with nominal compositions WC-10%Co4%Cr, WC-(W,Cr)₂C-7%Ni, Cr₃C₂-25%NiCr, (Ti,Mo)(C,N)-29%Ni and (Ti,Mo)(C,N)-29%Co were prepared with an ethylene-fuelled DJH 2700 HVOF spray gun. Electrolytic hard chromium (EHC) coatings and bulk (Ti,Mo)(C,N)-15%NiMo (TM10) hardmetal specimens were studied for comparison. The wear behaviour was investigated at room temperature, 400 and 600 °C. For the coatings sliding speeds were varied in the range 0.1–1 m/s for a wear distance of 5000 m and a normal force of 10 N. In some cases the WC- and (Ti,Mo)(C,N)-based coatings showed total wear rates (sum of wear rates of the rotating and stationary samples) of less than 10^?6 mm³/Nm, i.e., comparable to values typically measured under mixed/boundary conditions. Coefficients of friction above 0.4 were found for all test conditions. The P × V values as an engineering parameter for coating application are discussed. The microstructures and the sliding wear behaviour of the (Ti,Mo)(C,N)-based coatings and the (Ti,Mo)(C,N)-15%NiMo hardmetal are compared.     

Friction behaviour of chemical vapor deposited self-assembled monolayers on silicon wafer

Friction characteristics of self-assembled monolayers (SAMs) coated on Si-wafer (1 0 0) by chemical vapor deposition technique were studied experimentally at nano and micro-scales. Four self-assembled monolayers, such as dimethyldichlorosilane (DMDC), diphenyldichlorosilane (DPDC), perfluorooctyltrichlorosilane (PFOTS) and perfluorodecanoicacid (PFDA) coated on Si-wafer (1 0 0) were used as test materials. Nano-scale friction was measured using atomic force microscopy (AFM) in the range of 0–40 nN normal loads, in LFM (lateral force microscopy) mode, using a contact mode type Si₃N₄ tip. Results showed that the friction of SAMs at this scale was influenced by their physical/chemical properties, while that of Si-wafer by its inherent adhesion. Further, micro-scale friction tests were also performed with a ball-on-flat type micro-tribotester under reciprocating motion. Friction was measured in the range of 1500–4800 μN applied normal loads using glass balls of varying radii, viz., 0.25, 0.5 and 1 mm. It was observed that the performance of SAMs was more superior to Si-wafer even at micro-scale, except for PFDA. Evidences obtained using scanning electron microscope showed that Si-wafer and PFDA exhibited wear at this scale. Wear in the case of Si-wafer was due to solid–solid adhesion and that in the case of PFDA due to the influence of humidity (moisture). The micro-scale friction in both these materials was severely influenced by their wear.     

Sliding wear of silicon carbide modified by etching with chlorine at various temperatures

The effect of reaction temperature on the formation of a carbon layer on the surface of SiC has been investigated. Subsequently, the tribological properties of the formed carbon layers were studied. The experimental procedure involved exposing reaction-bonded SiC balls to a flowing gas mixture of 5% Cl₂, 2.5% H₂, and Ar at a high temperature of 800, 1000, or 1200 °C. A ball-on disk tribometer was used to investigate the friction and wear behavior of the treated specimens. While partially unreacted SiC phases were observed in the layer modified at 800 °C, rhombohedral graphite crystals were formed in the layer modified at 1200 °C. Compared to untreated SiC, the treated SiC materials were found to have relatively low friction coefficients and better wear resistance. Increasing the treatment temperature was found to improve the tribological performance of the resulting surface-modified SiC balls. A possible reason for this tribological improvement has been discussed based on the observed carbon phases.     

Effect of surface laser texture on friction properties of nickel-based composite

Laser surface texturing (LST) was performed on the nickel-based composites by a Nd:YAG pulsed laser and the regular-arranged dimples with diameter of 150 μm were fabricated on their surfaces. The textured surfaces were smeared with molybdenum disulfide powder. The tribological properties of the textured and filled composites were investigated by carrying out sliding wear tests against an alumina ball as a counterface using a high temperature ball-on-disk tribometer. The tests were conducted at a sliding speed of 0.4 m/s and at normal loads ranging from 20–100 N and from room temperature to 600 °C. The friction coefficient of nickel-based composite textured and smeared with molybdenum disulfide was found to reduce from 0.18 to 0.1 at the temperature range from 200 to 400 °C. The texture with a dimple density of 7.1% was observed to prolong wear life of MoS2 film by more than four times in comparison to the texture with other dimple densities. The lubricious oxide particles stored in the dimples reduce friction coefficient at elevated temperatures and compensate for the extra lubricant owing to the degradation of MoS₂ caused by its oxidation at high temperatures.