Abnormal blue-shift of Eu2+-activated calcium zirconium phosphates CaZr4(PO4)6

The electronic structure of CaZr₄(PO₄)₆ was calculated using the CASTEP code and the band gap for CaZr₄(PO₄)₆ can reach up to 4.30 eV. Ca_1−xEu_xZr₄(PO₄)₆ (0.01 ⩽ x ⩽ 1) samples were prepared by a high temperature solid-state reaction method. XRD analysis shows that Eu²⁺ ion can be totally incorporated into CaZr₄(PO₄)₆ forming complete solid solutions with trigonal lattice. Ca_1−xEu_xZr₄(PO₄)₆ (0.01 ⩽ x ⩽ 1) shows typical broad band emission in wavelength range from 400 to 650 nm for both under ultraviolet (UV) light and X-ray excitation, originating from the 4f⁶5d¹ → 4f⁷5d⁰ transition of Eu²⁺ ions. With increasing Eu²⁺ concentration, there is abnormal blue-shift of the emission peaks for Ca_1−xEu_xZr₄(PO₄)₆ due to the decreasing crystal field strength and Stokes shift. With increasing temperature in CaZr₄(PO₄)₆: Eu²⁺, its emission bands show the anomalous blue-shift with decreasing intensity. The overall scintillation efficiency of Ca_0.9Eu_0.1Zr₄(PO₄)₆ is 1.7 times of that of Bi₄Ge₃O₁₂ (BGO) powder under the same conditions. In addition, its predominant decay time is about 50 ns at room temperature. The potential application of Eu²⁺-doped CaZr₄(PO₄)₆ has been pointed out.     

Plasticized alkaline solid polymer electrolyte system

Alkaline solid polymer electrolytes were prepared by utilizing poly(vinyl alcohol) (PVA), potassium hydroxide (KOH), α-Al₂O₃ and different amounts of propylene carbonate (PC). The addition of PC to the PVA:KOH:α-Al₂O₃:H₂O increased its conductivity by three orders of magnitude to the reading of ∼ 10^− 4 S cm^− 1. The plot for log σ − 1 / T showed a transformation from liquid-like conductivity to Arrhenius type. The dielectric constant (ε_r) of the samples increases with increasing PC concentrations and temperatures. Scanning electron microscopy also shows the effect of PC on the polymer electrolytes surface. Thermogravimetric studies show that the thermal stability of the polymer electrolytes decreases with the addition of PC.     

Synthesis and characterization of a new p-phenylenediammonium dihydrogenmonophosphate [p-NH3C6H4NH3][H2PO4]2

Chemical preparation, crystal structure and NMR spectroscopy of a new organic cation p-phenylenediammonium monophosphate [p-NH₃C₆H₄NH₃][H₂PO₄]₂ are presented. This new compound crystallizes in the orthorhombic system, with the space group Pnma and the following parameters: a = 7.970 (2) Å; b = 22.770 (7) Å; c = 7.000 (7) Å, V = 1270.3 (11) Å³, Z = 4 and D_x = 1.590 g cm⁻³. The crystal structure has been determined and refined to R = 0.043 and R_(w) = 0.057 using 2623 independent reflections. The structural arrangement can be described as inorganic layers of (H₈P₄O₁₆)⁴⁻ units, parallel to (a, c) planes. The organic groups (p-H₃NC₆H₄NH₃)²⁺are anchored between the phosphoric layers to form a three-dimensional infinite network. This compound is also investigated by IR and solid-state ¹H, ¹³C and ³¹P MAS NMR spectroscopies. The ab initio method is used in the calculation of chemical shifts.     

Synthesis of LiFePO4/C doped with Mg2+ by reactive extrusion method

Reactive extrusion method is used to synthesizing LiMg_xFe_1−xPO₄/C, using LiOH⋅H₂O, FeC₂O₄⋅2H₂O, P₂O₅ and nano-MgO as raw materials and glucose as carbon source. Samples are investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), TG–DTA analysis and electrochemical performance test. Results show that amorphous product can be achieved after the reactive extrusion process. The particle size increases with the increase of magnesium content. Appropriately Mg²⁺ doping can reduce the electrode polarization effectively without seriously effect on material structure and morphology. LiMg_0.04Fe_0.96PO₄/C, showing the best electrochemical performances, has an initial discharge capacity of 155, 148, 140 and 137 mA h g⁻¹ at 0.2 C, 0.5 C, 1 C and 2 C rate, respectively. The discharge capacities remain above 99% after 20 cycles.     

Studies on polymer electrolyte poly(vinyl) pyrrolidone (PVP) complexed with ionic liquid: Effect of complexation on thermal stability,conductivity and relaxation behaviour

Polymer electrolyte films of PVP + x wt% ionic liquid (IL) (1-ethyl-3-methylimidazolium tetrafluoroborate [EMIM][BF₄]) for x = 0, 5, 10, 15, 20, 25 wt% have been prepared using solution cast technique. These films were characterized by TGA, DSC, FT-IR and ac impedance spectroscopy techniques. From XRD studies it is found that the inclusion of IL increases the amorphocity of polymeric membranes. DSC thermograms show that the glass transition (T_g) and melting temperatures (T_m) of PVP shift upon complexation with IL. FT-IR analysis shows the complexation of PVP with IL. Thermogravimetric studies show that PVP decomposes in a single step while PVP/IL membranes exhibit two step decomposition; lower value of decomposition temperature corresponds to the decomposition of PVP/IL complex while the higher decomposition temperature has been attributed to the decomposition of PVP. The decomposition temperature of PVP/IL complex decreases with the increasing amount of IL in the PVP membrane. Temperature dependence of conductivity and dielectric relaxation frequencies have also been studied for PVP and PVP/IL membranes. Both show thermally activated Arrhenius behaviour.     

High-rate performance of xLiFePO4·yLi3V2(PO4)3/C composite cathode materials synthesized via polyol process

xLiFePO₄·yLi₃V₂(PO₄)₃/C composite cathode materials were synthesized via a polyol process, using LiOH·H₂O, Fe₃(PO₄)₂·8H₂O, V₂O₅ and H₃PO₄ as raw materials, citric acid and PEG as carbon sources, and TEG as both a solvent and a reductant. Structural and morphological characterizations of as-prepared materials were carried out by X-ray diffraction (XRD) as well as scanning electron microscopy (SEM), respectively. Furthermore, electrochemical properties of as-prepared materials were analyzed by charge–discharge tests, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). XRD results indicated that the composites consisting of an olivine phase of LiFePO₄ and a monoclinic phase of Li₃V₂(PO₄)₃ are well-crystallized. It is found that the LF_0.6P·LV_0.4P/C composite exhibited better electrochemical performance than pristine LFP/C and LVP/C at 5 C and 10 C rate and delivered 126 mAh g^?1 and 110 mAh g^?1, respectively. The favorable particles morphology with less than 100 nm size and low extent agglomeration is believed as a factor. In addition, the co-existence of V³⁺-doped LiFePO₄/C and Fe²⁺-doped Li₃V₂(PO₄)₃/C was supposed as another reason.     

Microstructure,luminescence and thermal stability properties of NaSrPO4:Tb3+ phosphors with various doping concentrations prepared using conventional solid-state sintering

This paper reports the microstructure, luminescence and thermal stability properties of the NaSr_1−xPO₄:xTb³⁺ powders (x = 0.008, 0.01, 0.02, 0.04 and 0.06) via the conventional solid-state sintering at 1200 °C for 5 h. The X-ray diffraction result verifies all diffraction peaks are pure phase of NaSrPO₄. The luminescence results show that the NaSrPO₄:xTb³⁺ powders mainly excited at 370 nm have a series of the emission-states, related to the typical 4f → 4f intra-configuration forbidden transitions of Tb³⁺, and a major emission peak of around 546 nm. The concentration quenching of the NaSr_1−xPO₄:xTb³⁺ phosphors is appeared at x = 0.02. The decay time values of the NaSr_1−xPO₄:xTb³⁺ phosphors for the ⁵D₄ state of the Tb³⁺ are around 3.30 ms to 3.60 ms. It is also found the chromaticity coordinate of NaSrPO₄:Tb³⁺ phosphor varies with the increase of the concentration of Tb³⁺ ions from blue to green. Moreover, the thermal stability of the NaSrPO₄:xTb³⁺ phosphors is slightly better than that of conventional YAG phosphors.     

Preparation of aligned Fe3O4@Ag-nanowire/poly(vinyl alcohol) nanocomposite films via a low magnetic field

Aligned Fe₃O₄@Ag-nanowire (Ag-NW)/poly(vinyl alcohol) (PVA) nanocomposite films are prepared via a magnetic field-assisted method under a low magnetic field (B < 0.1 T) induction. The effects of the mass ratio (MR) of Fe₃O₄ to Ag-NWs and the Ag-NW content are systematically studied on the composite electrical conductivity (EC). The preferential alignment of Ag-NWs brings about a significant increase in the EC of the oriented composite in the parallel direction along the magnetic field. The optimal MR is determined to be equal to 0.15 at which the random composite has a good EC meanwhile the oriented composite shows a good response to the applied magnetic field. The oriented composite with the 20 wt% Ag-NWs shows a high EC anisotropy of ca. 6.6 and a very high EC of 4500 S/cm via the external magnetic field. In addition, the introduction of Ag-NWs leads to an obvious improvement in the thermal stability of PVA composites.     

Synthesis and tunable luminescence of RbCaGd(PO4)2:Ce3+, Mn2+ phosphors

RbCaGd(PO₄)₂ doped with Ce³⁺, Mn²⁺ was synthesized by the sol-gel method. The crystal structure and crystallographic location of Ce³⁺ in RbCaGd(PO₄)₂ were identified by Rietveld refinement. Powder X-ray diffraction (XRD) revealed that the structure of RbCaGd(PO₄)₂:Ce³⁺ compounds is hexagonal structure which is similar to that of hexagonal LnPO₄ with the lattice constant of a = b = 7.005(57) Å, c = 6.352(05) Å, and V (cell volume) = 269.980 Å³. The photoluminescence behavior and emission mechanism were studied systematically by doping activators in the RbCaGd(PO₄)₂ host. The Mn²⁺ incorporated RbCaGd(PO₄)₂:Ce³⁺, Mn²⁺ compounds exhibited blue emission from the parity- and spin-allowed f-d transition of Ce³⁺ and orange-to-red emission from the forbidden ⁴T₁ → ⁶A₁ transition of Mn²⁺. The emission chromaticity coordinates of RbCaGd(PO₄)₂:0.10Ce³⁺, xMn²⁺ (x = 0.16, 0.25) are close to the white region due to an energy transfer process and the energy transfer mechanism from Ce³⁺ to Mn²⁺ in the RbCaGd(PO₄)₂ host was dominated by dipole-dipole interactions.     

Facile synthesis of cubic fluorite nano-Ce1−xZrxO2 via hydrothermal crystallization method

Nano-Ce_1?xZr_xO₂ (x = 0.15, 0.25, 0.5) were synthesized via co-precipitation using NH₄OH as precipitant and hydrothermal crystallization. The XRD results confirmed that the cubic fluorite nano-Ce_1?xZr_xO₂ can form in NH₄OH solution (pH > 10) at 150 °C for 12 h, and well crystallized 20–50 nm nano-Ce_1?xZr_xO₂ were obtained at 200 °C for 22 h. The crystal growth of Ce_1?xZr_xO₂ was suppressed under higher OH^? concentration and crystallite size decreased with increasing concentration of NH₄OH. Ce3d XP spectra showed that the main valence state of the cerium on Ce_1?xZr_xO₂ surface is +4, and substituting Ce⁴⁺ with Zr⁴⁺ has no obvious influence on Ce³⁺/Ce⁴⁺ ratio.     

Effect of polymer modifier chain length on thermal conductive property of polyamide 6/graphene nanocomposites

The influence of polymer modifier chain length on the thermal conductivity of polyamide 6/graphene (GA) nanocomposites, including through-plane (λ_z) and in-plane (λ_x) directions were investigated. Here, three chain lengths of double amino-terminated polyethylene glycol (NH₂–PEG–NH₂) were used to covalently functionalize graphene with graphene content of 5.0 wt%. Results showed that λ_z was enhanced with the chain length of NH₂–PEG–NH₂ increased, but λ_x reached a maximum value at a certain chain length of NH₂–PEG–NH₂. The maximum λ_z and λ_x of GA are 0.406 W m⁻¹ K⁻¹ and 9.710 W m⁻¹ K⁻¹, respectively. This study serves as a foundation for further research on the thermal conductive property of graphene nanocomposites using different chain lengths of polymer modifier to improve the λ_z and λ_x of the thermal conductive materials.     

Microwave-induced combustion synthesis of Li0.5Fe2.5−xCrxO4 powder and their characterization

Li_0.5Fe_2.5−xCr_xO₄ (0 ≦ x ≦ 1.0) powders with small and uniformly sized particles were successfully synthesized by microwave-induced combustion, using lithium nitrate, iron nitrate, chromium nitrate, and carbohydrazide as the starting materials. The process takes only a few minutes to obtain as-received Cr-substituted lithium ferrite powders. The resultant powders annealed at 650 °C for 2 h and were investigated by thermogravimeter/differential thermal analyzer (TG/DTA), X-ray diffractometer (XRD), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM), and thermomagnetic analysis (TMA). The results revealed that the lattice constant decreases linearly with increasing of Cr content in Li_0.5Fe_2.5−xCr_xO₄ specimens. Moreover, the magnetic properties of Cr-substituted lithium ferrite were also strongly affected by Cr content. The saturation magnetization, remanent magnetization, and coercive force decrease monotonously with increasing of Cr content.     

Fabrication of asymmetric alumina membranes: I. Effect of SrO addition on thermal stabilization of transition aluminas

The effect of SrO addition on the thermal stabilization of transition aluminas with the aim of producing membrane layers (supported and unsupported) has been investigated. Al₂O₃–x wt.% SrO composite powders (x = 1, 3, 5, 8) were synthesized by co-precipitation of the hydroxides from solutions of AlCl₃ and Sr(NO₃)₂ salts using NH₄OH as a precipitating agent. Optimum SrO dopant concentration regarding the transition aluminas stabilization effect was determined to be 5 wt.% based on XRD analysis. STA analysis showed a 30 °C shift versus higher temperatures in the transformation of final transitional alumina (θ-Al₂O₃) to stable alpha phase due to addition of 5 wt.% SrO. The mechanism of transition aluminas thermal stabilization as a result of SrO addition is thoroughly discussed. Unsupported alumina membranes were prepared by drying boehmite sols at 600, 800, 1000 and 1100 °C. The effect of calcination temperature on surface area, pore size distribution of unsupported membranes containing 5 wt.% SrO has been investigated. The microstructure of unsupported and supported membranes revealed quite different. Smaller grains in the supported layers were attributed to the interaction between support and membrane.     

Characterization of M(H2PO4)2·2H2O (M = Mn,Co, Ni) and their in situ thermal decomposition by magnetic measurements

It has been established that M(H₂PO₄)₂·2H₂O (M = Mn, Co, Ni) are paramagnetics between 173 and 353 K with weak antiferromagnetic exchange interaction between the metal ions. In situ magnetic measurements during the thermal decomposition of the salts show that the oxidation state and the octahedral coordination of M²⁺ are preserved. From the data obtained it could be supposed that in M(H₂PO₄)₂·2H₂O (M = Co, Ni) this process is topotactic with no long-range diffusion transport. In Mn(H₂PO₄)₂·2H₂O, the formation of the large variety of intermediate products probably requires more drastic rearrangement and diffusion of the manganese ions during the complex transformations, which reflect on both the value and the sign of the θ constants. M₂P₄O₁₂ (M = Mn, Co, Ni), which are the final decomposition products of the corresponding dihydrogen phosphates are paramagnetics in the temperature range of 295–573 K with antiferomagnetic interactions between the metal ions. The lattice parameters of Ni(H₂PO₄)₂·2H₂O have been calculated. It crystallizes in the monoclinic system with a = 7.228(1) Å; b = 9.778(1) Å; c = 5.306(1) Å; β = 94.50(1)°, SG P2₁/n with Z = 2.     

Preparation,structure and electrical conductivity of pyrochlore-type samarium–lanthanum zirconate ceramics

A series of zirconate compounds with the general formula Sm_2–xLa_xZr₂O₇ (0 ? x ? 1.0) were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, structure and electrical conductivity of Sm_2–xLa_xZr₂O₇ ceramics were investigated by the Archimedes method, X-ray diffraction and impedance spectroscopy measurements. Sm_2–xLa_xZr₂O₇ (0 ? x ? 1.0) ceramics exhibit a pyrochlore-type structure. The measured electrical conductivity of Sm_2–xLa_xZr₂O₇ ceramics obeys the Arrhenius relation and gradually increases with increasing temperature from 673 to 1173 K. Sm_2–xLa_xZr₂O₇ ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10^?4 to 1.0 atm at all test temperature levels. The electrical conductivity of Sm_2–xLa_xZr₂O₇ ceramics decreases with increasing lanthanum content at identical temperature levels.     

Brushite (CaHPO4·2H2O) to octacalcium phosphate (Ca8(HPO4)2(PO4)4·5H2O) transformation in DMEM solutions at 36.5 °C

The purpose of this study was to investigate the transformation of brushite (dicalcium phosphate dihydrate, DCPD, CaHPO₄·2H₂O) powders at 36.5 °C in DMEM (Dulbecco's Modified Eagle Medium) solutions. Two sets of brushite powders with different particle shapes were synthesized to use in the above DMEM study. The first of these brushite powders was prepared by using a method which consisted of stirring calcite (CaCO₃) powders in a solution of ammonium dihydrogen phosphate (NH₄H₂PO₄) from 6 to 60 min at room temperature. These powders were found to consist of dumbbells of water lily-shaped crystals. The second one of the brushite powders had the common flat-plate morphology. Both powders were separately tested in DMEM-immersion experiments. Monetite (DCPA, CaHPO₄) powders were synthesized with a unique water lily morphology by heating the water lily-shaped brushite crystals at 200 °C for 2 h. Brushite powders were found to transform into octacalcium phosphate (OCP, Ca₈(HPO₄)₂(PO₄)₄·5H₂O) upon soaking in DMEM (Dulbecco's Modified Eagle Medium) solutions at 36.5 °C over a period of 24 h to 1 week. Brushite powders were known to transform into apatite when immersed in synthetic (simulated) body fluid (SBF) solutions. This study found that DMEM solutions are able to convert brushite into OCP, instead of apatite.     

Both initial concentrations of Fe(II) and monovalent cations jointly determine the formation of biogenic iron hydroxysulfate precipitates in acidic sulfate-rich environments

In order to accurately predict the types of biogenic iron hydroxysulfate precipitates in acidic, sulfate-rich environments facilitated by Acidithiobacillus ferrooxidans, different initial concentrations of Fe^2 +, K⁺, Na⁺, and NH₄⁺ are selected and tested in batch experiments for the formation of the precipitates. The critical equations of jarosite formation in FeSO₄–K₂SO₄–H₂O system or FeSO₄–(NH₄)₂SO₄–H₂O system could be described as Y = ? 22120.8077 ? 0.04257x + 0.006170x² (R² = 0.9979) or Y = 0.03540 ? 0.002950x + 7.407E ? 5x² (R² = 0.9934), respectively, where Y is the threshold or critical values of the molar ratio of Fe/K or Fe/NH₄ for jarosite formation, and x (mmol/L) is the initial concentration of Fe(II). Schwertmannite is the sole biogenic secondary ferric mineral when molar ratio of Fe/K or Fe/NH₄ is higher than Y in the system with a given initial Fe(II) concentration. The precipitates are an admixture of schwertmannite and jarosite, or pure jarosite when the Fe/M molar ratio is lower than Y. The crystallinity of the secondary ferric minerals increased with the increase of initial Fe(II) concentration in the medium with a fixed K⁺ concentration. It is observed that the capacity of monovalent cation in promoting jarosite formation is K⁺ > NH₄⁺ > Na⁺, as exhibiting that the capacity of K⁺ in this process is about 75 and 200 times greater than NH₄⁺ and Na⁺, respectively. Obviously, both the initial concentration of Fe(II) and molar ratio of Fe to monovalent cation determine the types of biogenic iron hydroxysulfate precipitates.     

Effects of excitation wavelength and Y3+ content on luminescent properties of YMO4:Dy3+ (M = V,P) phosphors induced by ultraviolet excitation

Y_0.99VO₄:0.01Dy³⁺, Y_0.99PO₄:0.01Dy³⁺ and Y_xVO₄:0.01Dy³⁺ phosphors were synthesized by chemical co-precipitation method. All the samples were characterized by X-ray powder diffraction (XRD) and photoluminescence spectroscopy. XRD results show that the samples only have single tetragonal structure and the crystallinity of Y_0.99VO₄:0.01Dy³⁺ phosphor is higher than that of Y_0.99PO₄:0.01Dy³⁺ phosphor when the heat treatment process is same. Photoluminescence excitation spectra results show that the Y_0.99VO₄:0.01Dy³⁺ and Y_0.99PO₄:0.01Dy³⁺ phosphors can be efficiently excited by ultraviolet light from 250 nm to 380 nm, the former have a wide Dy³⁺–O^2? charge transfer band ranging from 260 nm to 350 nm including a peak at 310 nm, the latter have four peaks at 294 nm, 326 nm, 352 nm and 365 nm. Emission spectra of all the samples exhibit a strong blue emission (483 nm) and another strong yellow emission (574 nm). Moreover, the yellow-to-blue emission intensity ratio and color temperature of emission of Dy³⁺ are strongly related to excitation wavelength in Y_0.99PO₄:0.01Dy³⁺ phosphor, but it is almost not in Y_0.99VO₄:0.01Dy³⁺ phosphor. For Y_xVO₄:0.01Dy³⁺ (x = 0.94, 0.97, 0.99, 1.01, 1.03) phosphors, with increasing value of x, the body color of phosphor changes from yellow to white and the strongest peak in excitation spectra shifts a little to shorter wavelength. It is detrimental to luminous intensity when Y³⁺ content deviate stoichiometric ratio, but the influence of Y³⁺ on the color temperature of emission of YVO₄:Dy³⁺ phosphor is slight.     

A pulsed optical absorption spectroscopy study of wide band-gap optical materials

The paper presents the results of a study on the formation and evolution of short-lived radiation-induced defects in wide band-gap optical materials with the mobile cations. The spectra and decay kinetics of transient optical absorption (TOA) of radiation defects in crystals of potassium and ammonium dihydro phosphates (KH₂PO₄ and NH₄H₂PO₄) were studied by means of the method of pulsed optical absorption spectroscopy with the nanosecond time resolution under excitation with an electron-beam (250 keV, 10 ns). A model of electron tunneling between the electron and hole centers under conditions of the thermally stimulated mobility of one of the recombination process partners was developed. The model describes all the features of the induced optical density relaxation kinetics observed in nonlinear optical crystals KH₂PO₄ and NH₄H₂PO₄ in a broad decay-time range of 10 ns–10 s after the pulse of radiation exposure. The paper discusses the origin of radiation defects that determine the TOA, as well as the dependence of the decay kinetics of the TOA on the temperature, excitation power and other experimental conditions.     

Electrical properties and thermal expansion of cobalt doped apatite-type lanthanum silicates based electrolytes for IT-SOFC

The thermal expansion and conductivities have been investigated for Co³⁺ doped lanthanum silicates. The apatite-type lanthanum silicates with formula La₁₀Si_6?xCo_xO_27?x/2 (x = 0.2, 0.4, 0.6, 0.8, 1.0, 1.5) were synthesized by sol–gel process. The thermal expansion coefficient (TEC) of La₁₀Si_6?xCo_xO_27?x/2 was improved with increasing cobalt content because of the lower valence and larger radius of Co³⁺ ion compared to Si⁴⁺. Analysis of AC impedance spectroscopy showed that conductivity increased first and then decreased with increasing cobalt content. There is an optimum doping amount of cobalt and La₁₀Si_5.2Co_0.8O_26.6 exhibits the highest conductivity of 3.33 × 10^?2 S/cm at 800 °C. When x ≤ 0.8, the local distortion caused by doping with Co³⁺ can significantly affect the oxygen channels and assist the migration of the interstitial oxide ions, resulting in the improvement of ionic conductivity. However, excess Co³⁺ dopant (0.8 < x ≤ 1.5) reduced the number of interstitial oxide ions and decreased the conductivity.