The production of flower-like NiFe2O4 superstructures consisting of nanosheets via the thermolysis of a heterometallic oxo-centered trinuclear complex

Flower-like NiFe₂O₄ superstructures consisting of nanosheets have been successfully synthesized by direct thermolysis of a heterometallic oxo-centered trinuclear complex [NiFe₂O(CH₃COO)₆(H₂O)₃·2H₂O] (NiFe-HOTC) at 400 °C for 6 h in a horizontal tube furnace. The composition and structure of the products were investigated by X-ray diffraction (XRD) and infrared spectra (IR). XRD analysis revealed a pure ferrite phase with high crystallinity. Morphological investigation by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) showed NiFe₂O₄ flowers with average diameter varying from 0.5 to 3 μm consist of nanosheets with average edge length in the range of 60-300 nm and thickness of about 30 nm. Furthermore, energy dispersive X-ray analysis (EDX) demonstrated that the atom ration of Ni, Fe and O is 1:2:4. In addition, magnetic measurements showed that the obtained flower-like NiFe₂O₄ are ferromagnetic at room temperature.     

Preparation and properties of NiFe2O4 nanowires

Polycrystalline NiFe₂O₄ nanowires have been synthesized by PEG assisted co-precipitation method. The formation mechanism of the nanowires proposed is by means of the orientational aggregation of individual nanoparticles. X-ray diffraction, high resolution scanning electron microscopy, transmission electron microscopy, microRaman and vibrating sample magnetometry studies were carried out. The results show that NiFe₂O₄ nanowires were in polycrystalline form with diameter of 58 nm. The synthesized nanowires show room temperature ferromagnetic property with high coercivity. This method is expected to be useful for large scale synthesis of NiFe₂O₄ nanowires for the application of magnetic recording.     

Electrical conductivity of 5 mol.% Yb2O3 and 5 mol.% Gd2O3 co-doped Sm2Zr2O7

Sm₂Zr₂O₇ co-doped with and without 5 mol.% Yb₂O₃ and 5 mol.% Gd₂O₃ were prepared by a pressureless-sintering method at 1973 K for 10 h in air. The relative density, structure and electrical conductivity were investigated by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance spectra measurements. Both Sm₂Zr₂O₇ and (Sm_0.9Gd_0.05Yb_0.05)₂Zr₂O₇ ceramics exhibit a single phase of pyrochlore-type structure. The grain conductivity, grain-boundary conductivity and total conductivity obey the Arrhenius relation, respectively, and gradually increase with increasing temperature from 723 to 1173 K. (Sm_0.9Gd_0.05Yb_0.05)₂Zr₂O₇ ceramic is the oxide-ion conductor in an oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The grain conductivity, grain-boundary conductivity and total conductivity of (Sm_0.9Gd_0.05Yb_0.05)₂Zr₂O₇ with dual Yb³⁺ + Gd³⁺ doping are higher than those of undoped Sm₂Zr₂O₇ at identical temperature levels.     

Synthesis of nanostructured M/Fe3O4 (M = Ag,Cu) composites using hexamethylentetramine and their electrocatalytic properties

Nanoscaled Ag/Fe₃O₄ hybrids with different Ag contents and Cu/Fe₃O₄ nanoshpere and microsphere were successfully synthesized with assistance of sodium citrate and (CH₂)₆N₄ via a hydrothermal process. The as-prepared samples were identified and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), and X-ray photoelectron spectroscopy (XPS), respectively. All samples were used as electrocatalysts modified on a glassy carbon electrode for p-nitrophenol reduction in a basic solution. The catalytic activity of Ag/Fe₃O₄ samples increased first and then decreased by increasing Ag content from 0% to 8%, and the one with 6% Ag displayed the highest catalytic activity. All the Cu/Fe₃O₄ samples exhibited enhanced catalytic activity by comparison with a glassy carbon electrode, and the one prepared with the molar ratio of Cu²⁺, Fe³⁺, citrate anion, and (CH₂)₆N₄ with 1:1:3:5 exhibited the highest catalytic activity.     

Self-controlled growth of Fe3BO6 crystallites in shape of nanorods from iron-borate glass of small templates

Fe₃BO₆ can be an ideal compound for devising functional magnetic and dielectric properties in a single material for multiple applications such as electrodes, gas sensors, or medical tools. Useful to tailor such properties, here we report on a self-controlled Fe₃BO₆ growth in a specific shape of nanorods from a supercooled liquid precursor (an inorganic polymeric liquid or glass) of an initial composition (100 − x)B₂O₃ − xFe₂O₃, x = 40–50 mol%. B₂O₃ as a strong glass former co-bridges the Fe³⁺ ions in oxygen polygons primarily in a 2-D interconnected polymer network so that it dictates preferably a 1-D directional growth on the reaction Fe³⁺ species in form of a compound Fe₃BO₆, a favorable phase to nucleate and grow when annealing a precursor at 500–800 °C in ambient air. Distinct nanorods with a diameter ∼200 nm and 40–100 μm length have been formed on 10–15 min annealing a sample in microwave at moderate temperature 550 °C. A bonded surface B₂O₃ layer (15–25 nm thickness) has grown on the Fe₃BO₆ of the nanorods in situ in a specific structure. XPS bands in the Fe³⁺, B³⁺ and O²⁻ species confer this model structure. A local BO₃ → BO₄ conversion has incurred in the boroxol (B₃O_4.5)_n, n → ∞, rings in the surface layer, showing three distinct IR bands at 1035, 1215 and 1425 cm⁻¹.     

The effects of quenching treatment and AlF3 coating on LiNi0.5Mn0.5O2 cathode materials for lithium-ion battery

Submicron layered LiNi_0.5Mn_0.5O₂ was synthesized via a co-precipitation and solid-state reaction method together with a quenching process. The crystal structure and morphology of the materials were investigated by X-ray diffraction (XRD), Brunauer–Emmett and Teller (BET) surface area and scanning electron microscopy (SEM) techniques. It is found that LiNi_0.5Mn_0.5O₂ material prepared with quenching methods has smooth and regular structure in submicron scale with surface area of 0.43 m² g⁻¹. The initial discharge capacities are 175.8 mAh g⁻¹ at 0.1 C (28 mA g⁻¹) and 120.3 mAh g⁻¹ at 5.0 C (1400 mA g⁻¹), respectively, for the quenched samples between 2.5 and 4.5 V. It is demonstrated that quenching method is a useful approach for the preparation of submicron layered LiNi_0.5Mn_0.5O₂ cathode materials with excellent rate performance. In addition, the cycling performance of quenched-LiNi_0.5Mn_0.5O₂ material was also greatly improved by AlF₃ coating technique.     

Optical properties of transparent Dy doped Ba2TiSi2O8 glass ceramic

The Ba₂TiSi₂O₈ is a well known piezoelectric, ferroelectric and non-linear crystal. Nanocrystals of Ba₂TiSi₂O₈ doped with 1.5 Dy³⁺ have been obtained by thermal treatment of a precursor glass and their optical properties have been studied. X-ray diffraction patterns and optical measurements have been carried out on the precursor glass and glass ceramic samples. The emission spectra corresponding to the Dy³⁺: ⁴F_9/2 → ⁶H_13/2 (575 nm), ⁴F_9/2 → ⁶H_11/2 (670 nm) and ⁴F_9/2 → ⁶H_9/2 (757 nm) transitions have been obtained under laser excitation at 473 nm. These measurements confirm the incorporation of the Dy³⁺ ions into the Ba₂TiSi₂O₈ nanocrystals which produces an enhancement of luminescence at 575 nm. At this wavelength has been demonstrated a maximum optical amplification around 1.9 cm⁻¹ (∼8.2 dB/cm).     

Conversion of green emission into white light in Gd2O3 nanophosphors

Gd₂O₃ nanophosphors were prepared by combustion synthesis with and without doping of Dy³⁺ ions. The X-ray powder diffraction patterns indicate that as-prepared Gd₂O₃ and 0.1 mol% Dy₂O₃ doped Gd₂O₃ nanophosphors have monoclinic structures. The transmission electron microscope (TEM) studies revealed that the as-prepared phosphors had an average crystallite sizes around 37 nm. The excitation and emission properties have been investigated for Dy³⁺ doped and undoped Gd₂O₃ nanophosphors. New emission bands were observed in the visible region for Gd₂O₃ nanophosphors without any rare earth ion doping under different excitations. A tentative mechanism for the origin of luminescence from Gd₂O₃ host was discussed. Emission properties also measured for 0.1 mol% Dy³⁺ doped Gd₂O₃ nanophosphors and found the characteristic Dy³⁺ visible emissions at 489 and 580 nm due to ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions, respectively. The chromaticity coordinates were calculated based on the emission spectra of Dy³⁺ doped and undoped Gd₂O₃ nanophosphors and analyzed with Commission Internationale de l'Eclairage (CIE) chromaticity diagram. These nanophosphors exhibit green color in undoped Gd₂O₃ and white color after adding 0.1 mol% Dy₂O₃ to Gd₂O₃ nanophosphors under UV excitation. These phosphors could be a promising phosphor for applications in flat panel displays.     

Effect of chromium substitution on structure and magnetic properties of Bi2Fe4O9

Orthorhombic Bi₂Fe_4 − xCr_xO₉ (x = 0.0, 0.25, and 0.75) nanoplatelets were synthesized by a simple hydrothermal method. The structure, morphology, and magnetic properties of the obtained powders have been characterized. Calculation of the lattice parameters of Bi₂Fe_4 − xCr_xO₉, as well as bond lengths and angles, was carried out by X-ray diffraction Rietveld refinement. The volumes of the metal-oxygen tetrahedra and octahedra were calculated to be sequentially increasing as the Cr doping level increases. The samples undergo an antiferromagnetic transition at 250 ± 5 K. The magnetic moments of the samples increase with higher Cr doping level. The 3d electron spin state for Fe³⁺ in the as-prepared samples is different, which is possibly due to the distortion of Fe-O tetrahedra and octahedra in the crystal structure after chromium substitution.     

Influence of excitation wavelengths on luminescent properties of Sr3Al2O6:Eu, Dy phosphors prepared by sol-gel-combustion processing

Eu²⁺ and Dy³⁺ ion co-doped Sr₃Al₂O₆ red-emitting long afterglow phosphor was synthesized by sol-gel-combustion methods using Sr(NO₃)₂, Al(NO₃)₃·9H₂O, Eu₂O₃, Dy₂O₃, H₃BO₃ and C₆H₈O₇·H₂O as raw materials. The crystalline structure of the phosphors were characterized by X-ray diffraction, luminescent properties of phosphors were analyzed by fluorescence spectrophotometer. The effect of excitation wavelengths on the luminescent properties of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphors was discussed. The emission peak of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphor lays at 516 nm under the excitation of 360 nm, and at 612 nm under the excitation of 468 nm. The results reveal that the Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphor will emit a yellow-green light upon UV illumination, and a bright red light upon visible light illumination. The emission mechanism was discussed according to the effect of nephelauxetic and crystal field on the 4f⁶5d¹ → 4f⁷ transition of the Eu²⁺ ions in Sr₃Al₂O₆. The afterglow time of (Sr_0.94Eu_0.03Dy_0.03)₃ Al₂O₆ phosphors lasts for over 600s after the excited source was cut off.     

Observation of broadband infrared luminescence in a novel Bi-doped P2O5-B2O3-Al2O3 glass

A novel Bi-doped P₂O₅-B₂O₃-Al₂O₃ glass was investigated, and strong broadband NIR (near infrared) luminescence was observed when the sample was excited by 445 nm, 532 nm, 808 nm and 980 nm lasers, respectively. The max FWHM with 312 nm, the lifetime with 580 μs and the σ_emτ product with 5.3 × 10^− 24 cm² s were obtained which indicates that this glass is a promising material for broadband optical amplifier and tunable laser. The effect of the introduction of B₂O₃ on the glass structure and Bi-ions illuminant mechanism were discussed and analyzed. It is suggested that the introduction of B₂O₃ makes the glass structure closer, and the broadband NIR emission derives from Bi⁰:²D_3/2 → ⁴S_3/2 and Bi⁺:³P₁ → ³P₀ transitions.     

Synthesis and luminescent characteristic of Eu-doped (Gd,Lu)2O3 nanopowders

Eu³⁺ doped (Gd,Lu)₂O₃ nanopowders with particle sizes ranging from 20 to 70 nm were synthesized by the co-precipitant method using mixed precipitants, namely the mixture of ammonium hydroxide (NH₃⋅H₂O) and ammonium hydrogen carbonate (NH₄HCO₃). The precipitate precursor prepared by this method was believed to possess a basic carbonate composition and its thermal decomposition of the (Gd,Lu)₂O₃:Eu³⁺ powders were investigated by Thermogravimetric analysis and differential thermal analysis (TG-DTA). This preparation was followed by a calcination process at 800-1100 °C and corresponding phosphor structure were examined by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Photoluminescence measurement of the (Gd,Lu)₂O₃:Eu³⁺ particles show typical red emission at the 612 nm corresponding to the ⁵D₀ → ⁷F₂ transition. We found that the optimal Eu³⁺ molar doping concentration, calcined temperature and reaction time were 7 mol%, 1000 °C, and 2 h, respectively, which is helpful to obtain the final transparent ceramics with excellent properties.     

Ar assisted carbidization of TiO2 (1 1 0) supported Mo nanoparticles by decomposition of C2H4

Ar⁺ assisted carbidization of Mo nanoparticles supported on TiO₂ (1 1 0) is studied by scanning tunneling microscopy (STM) and X-ray photoelectron spectroscopy (XPS). In order to activate the diffusion of carbon into the bulk of Mo nanoparticles we applied Ar ions (1 keV) during the exposure of C₂H₄. XPS exhibited that the decomposition of C₂H₄ at 850 K accompanied by ion bombardment results in an almost complete carbidization of nanocrystalline Mo while this treatment performed without ion bombardment results only in the carbidization of the particle surface. The modification of the crystallinity of the Mo-carbide particles was deduced from STM measurements.     

A yellow-emitting Ca3Si2O7: Eu phosphor for white LEDs

A series of yellow-emitting phosphors based on a silicate host matrix, Ca_3 − xSi₂O₇: xEu²⁺, was prepared by solid-state reaction method. The structure and photoluminescent properties of the phosphors were investigated. The XRD results show that the Eu²⁺ substitution of Ca²⁺ does not change the structure of Ca₃Si₂O₇ host and there is no impurity phase for x < 0.12. The SEM images display that phosphors aggregate obviously and the shape of the phosphor particle is irregular. The EDX results reveal that the phosphors consist of Ca, Si, O, Eu and the concentration of these elements is close to the stoichiometric composition. The Ca_3 − xSi₂O₇: xEu²⁺ phosphors can be excited at a wavelength of 300-490 nm, which is suitable for the emission band of near ultraviolet or blue light-emitting-diode (LED) chips. The phosphors exhibit a broad emission region from 520 to 650 nm and the emission peak centered at 568 nm. In addition, the shape and the position of the emission peak are not influenced by the Eu²⁺ concentration and excitation wavelength. The phosphor for x = 0.045 has the strongest excitation and emission intensity, and the Ca_3 − xSi₂O₇: xEu²⁺ phosphors can be used as candidates for the white LEDs.     

Studying trivalent/bivalent metal ion doped TiO2 as p-TiO2 in bipolar heterojunction devices

Trivalent/bivalent metal ions doped TiO₂ thin films (M_xTi_1−xO₂, M = Cr³⁺, Fe³⁺, Ni²⁺, Co²⁺, Mn²⁺ and x = 0.01, 0.05, 0.1, 0.15, 0.2) were deposited on Indium–tin oxide (ITO) coated glass substrates by spin coating technique. X-ray photoelectron spectroscopy (XPS) showed Ti⁴⁺ oxidation state of the Ti2p band in the doped p-TiO₂. The homogenous M_xTi_1−xO₂ was used to support n-ZnO thin films with thickness ∼40–80 nm and vertically aligned n-ZnO nanorods (NR) with length ∼300 nm and 1.5 μm. Current (I)–voltage (V) characteristics for the Ag/n-ZnO/M_xTi_1−xO₂/ITO/glass assembly showed rectifying behavior with small turn-on voltages (V₀) < 1 V. The ideality factor (η) and the resistances in both forward and reverse bias were calculated. The temperature dependence performance of these bipolar devices was performed and variation of the parameters with temperature was studied.     

Photoluminescence properties of RE-activated Na3GdP2O8 (RE = Tb, Dy, Eu, Sm) under VUV excitation

RE³⁺-activated monoclinic Na₃GdP₂O₈ (RE³⁺ = Tb³⁺, Dy³⁺, Eu³⁺, Sm³⁺) phosphors have been synthesized by a solid-state reaction method. Their photoluminescence properties in the vacuum ultraviolet (VUV) region were investigated. By analyzing their excitation spectra, the host-related absorption band was determined to be around 166 nm. The f-d transition bands and the charge transfer bands for Na₃GdP₂O₈:RE³⁺ (RE³⁺ = Tb³⁺, Dy³⁺, Eu³⁺, Sm³⁺) were assigned and corroborated. For the sample Na₃GdP₂O₈:5%Tb³⁺, the strong bands at around 202 and 221 nm are assigned to the 4f-5d spin-allowed transitions and the weak band at 266 nm is related to the spin-forbidden transition of Tb³⁺. For Na₃GdP₂O₈:5%Dy³⁺, the broad band at 176 nm could be related to the f-d transitions of Dy³⁺ and the O²⁻ → Dy³⁺ charge transfer band (CTB) besides the host-related absorption. In the excitation spectrum of Eu³⁺ doped sample, the O²⁻ → Eu³⁺ CTB is observed to be at 245 nm. For the Sm³⁺ doped sample, the O²⁻ → Sm³⁺ CTB is not distinguished obviously and is overlapped with the host-related absorption band.     

Sr3.5Mg0.5Si3O8Cl4: Eu bluish-green-emitting phosphor for NUV-based LED

Sr₄Si₃O₈Cl₄:Eu²⁺ and Sr_3.5Mg_0.5Si₃O₈Cl₄:Eu²⁺ phosphors were prepared by a conventional solid state reaction (SS). Excited by 370 nm near-ultraviolet light, the phosphors show an efficient bluish-green wide-band emission centering at 484 nm, which originates from the 4f5d¹ → 4f⁷ transition of Eu²⁺ ion. The excitation spectra of the phosphors are a broad band extending from 250 nm to 400 nm. Mg²⁺-codoping greatly enhances the bluish-green emission of the phosphors. An LED was fabricated by coating the Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ phosphor onto an ~ 370 nm-emitting InGaN chip. The LED exhibits bright bluish-green emission under a forward bias of 20 mA. The results indicate that Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ is a candidate as a bluish-green component for fabrication of NUV-based white LEDs.     

Electronic structure and photoluminescence properties of Eu-activated Ca4Si2O7F2

The blue-emitting phosphors Ca_(4−x)Eu_xSi₂O₇F₂ (0 < x ? 0.05) have been prepared by solid-state reaction and the photoluminescence properties have been studied systematically. The electronic structure of calcium fluoride silicate Ca₄Si₂O₇F₂ was calculated using the CASTEP code. The calculation results of electronic structure show that Ca₄Si₂O₇F₂ has an indirect band gap with 5 eV. The top of the valence band is dominated by O 2p and Si 3p states, while the bottom of the conduction band is mainly composed of Ca 3d states. Under the 350 nm excitation, the obtained sample shows a broad emission band in the wavelength range of 400-500 nm with peaks of 413 nm and 460 nm from two different luminescence centers, respectively. The relative intensity of the two peaks changes with the alteration of the Eu²⁺ concentration. The strong excitation bands of the powder in the wavelength range of 200-420 nm are favorable properties for the application as lighting-emitting-diode conversion phosphor.     

Synthesis and electrochemical properties of Co3O4 nanofibers as anode materials for lithium-ion batteries

Co₃O₄ nanofibers as anode materials for lithium-ion batteries were prepared from sol precursors by using electrospinning. The morphology, structure and electrochemical properties of Co₃O₄ nanofibers were characterized by atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and charge-discharge experiments. The results show that Co₃O₄ nanofibers possessed typical spinel structure with average diameter of 200 nm. The initial capacity of Co₃O₄ nanofibers was 1336 mAhg^− 1 and the capacity reached 604 mAhg^− 1 up to 40 cycles. It was suggested that the high reversible capacity could be ascribed to the high surface area offered by the nanofibers' structure.     

Long wavelength Ce emission in Y6Si3O9N4 phosphors for white-emitting diodes

Y₆Si₃O₉N₄:Ce³⁺ phosphor was prepared by a solid-state reaction in reductive atmosphere. X-ray powder diffraction (XRD) analysis confirmed the formation of Y₆Si₃O₉N₄:Ce³⁺. Scanning electron microscopy (SEM) observation indicated that the microstructure of the phosphor consisted of irregular fine grains with an average size of about 5 μm. Photoluminescence (PL) measurements showed that the phosphor can be efficiently excited by near ultraviolet (UV) or blue light excitation, and exhibited bright green emission peaked at about 525 nm. Compared with Ce³⁺-doped Y₄Si₂O₇N₂ phosphors, Ce³⁺-doped Y₆Si₃O₉N₄ phosphors showed longer wavelengths of both excitation and emission. The Y₆Si₃O₉N₄:Ce³⁺ is a potential green-emitting phosphor for white LEDs.