Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition

Machining of steel inherently generates high cutting temperature, which not only reduces tool life but also impairs the product quality. Conventional cutting fluids are ineffective in controlling the high cutting temperature and rapid tool wear. Further, they also deteriorate the working environment and lead to general environmental pollution. Cryogenic cooling is an environment friendly clean technology for desirable control of cutting temperature. The present work deals with experimental investigation in the role of cryogenic cooling by liquid nitrogen jet on cutting temperature, tool wear, surface finish and dimensional deviation in turning of AISI-4037 steel at industrial speed-feed combination by coated carbide insert. The results have been compared with dry machining and machining with soluble oil as coolant. The results of the present work indicate substantial benefit of cryogenic cooling on tool life, surface finish and dimensional deviation. This may be attributed mainly to the reduction in cutting zone temperature and favorable change in the chip–tool interaction. Further it was evident that machining with soluble oil cooling failed to provide any significant improvement in tool life, rather surface finish deteriorated.     

An experimental investigation on effect of minimum quantity lubrication in machining AISI 1040 steel

The growing demands for high productivity of machining need use of high cutting velocity and feed rate. Such machining inherently produces high cutting temperature, which not only reduces tool life but also impairs the product quality. Application of cutting fluids changes the performance of machining operations because of their lubrication, cooling, and chip flushing functions. But the conventional cutting fluids are not that effective in such high production machining, particularly in continuous cutting of materials likes steels. Minimum quantity lubrication (MQL) presents itself as a viable alternative for turning with respect to tool wear, heat dissipation, and machined surface quality. This study compares the mechanical performance of MQL to completely dry lubrication for the turning of AISI-1040 steel based on experimental measurement of cutting temperature, chip reduction coefficient, cutting forces, tool wears, surface finish, and dimensional deviation. Results indicated that the use of near dry lubrication leads to lower cutting temperature and cutting force, favorable chip–tool interaction, reduced tool wears, surface roughness, and dimensional deviation.     

Using PCD for machining CGI with a CO2 coolant system

Polycrystalline diamond is widely used as a economic cutting material for machining non-ferrous materials such as aluminum. It is perceived that diamond cannot be used for cutting ferrous materials due to the high affinity of carbon to iron. Nevertheless, under certain conditions it is possible to use diamond materials for cutting ferrous metals. In order to avoid graphitization of the diamond matrix, it is necessary to keep the cutting temperature below the critical level of diamond graphitization. This paper presents the influence of a cryogenic CO₂ coolant strategy on the cutting process using PCD tools for cutting high strength compacted graphite iron (CGI). Investigations show, that tool wear behavior strongly correlates with the cutting speed, the cutting forces, cutting temperatures, and surface roughness of the workpiece. The test results show, that the tool life of PCD for cutting cast iron is dependent on the diamond grain size, the binder material, and the cutting parameters.     

Cooling techniques for improved productivity in turning

The past century has witnessed significant advancements in turning process, cutting tools, machine controls and coolant/lubricant chemistry. These developments have particularly enhanced the machining of difficult-to-cut materials, which are used for aerospace, steam turbine, bearing industry, nuclear and automotive applications. In turning operation, friction and heat generation at the cutting zone are the frequent problems, which affect the tool life and surface finish apart from other machining results. This mechanism of heat generation plays quite a negative role during the turning of modern materials due to their peculiar characteristics such as poor thermal conductivity, high strength at elevated temperature, resistance to wear and chemical degradation. A good understanding of the methods of lubrication/cooling at the cutting zone, reduction of heat generation will lead to efficient and economic machining of these modern materials. This paper presents an overview of major advances in techniques as minimum quantity lubrication (MQL)/near dry machining (NDM), high pressure coolant (HPC), cryogenic cooling, compressed air cooling and use of solid lubricants/coolants. These techniques have resulted in reduction in friction and heat at the cutting zone, hence improved productivity of the process. A brief survey of modeling/FEA techniques is also performed.     

Temperature of internally-cooled diamond-coated tools for dry-cutting titanium

The role of cutting fluids is well known for the importance of removing heat from the cutting edge, lubricating the sliding chip contact and transporting the metal chips away from the cutting zone. Dry machining leads to increased cutting temperatures and higher wear rates resulting in shorter tool life; this is particularly evident in the cutting of high strength materials. Diamond coated cutting inserts are not usually considered for machining titanium due to rapid oxidation of the coating at the temperatures typical of titanium machining. This paper examines the formation of hot-spots on the rake face during dry and near-dry turning of titanium using conventional cemented carbide inserts. Machining performance is assessed by measurement of tool wear and tool life. Trials with an internally cooled tool with a specially designed, diamond coated insert have shown that the heat from the cutting operation can be rapidly diffused over the entire surface of the insert and thus successfully drawn away from the tool via closed loop recirculation of coolant through the tool holder. This enables wear to be inhibited by management of rake face temperature to keep it below the critical temperatures at which these prominent wear mechanisms operate. Measurements of change in coolant temperature before and after circulation are used to quantify the heat removed from the cutting process. The low friction coefficient and high thermal conductivity of diamond, assisted by the indirect cooling, results in longer tool life whilst maintaining high standards of surface finish.     

Refrigerated cooling air cutting of difficult-to-cut materials

One approach to enhance machining performance is to apply cutting fluids during cutting process. However, the use of cutting fluids in machining process has caused some problems such as high cost, pollution, and hazards to operator's health. All the problems related to the use of cutting fluids have urged researchers to search for some alternatives to minimize or even avoid the use of cutting fluids in machining operations. Cooling gas cutting is one of these alternatives. This paper investigates the effect of cooling air cutting on tool wear, surface finish and chip shape in finish turning of Inconel 718 nickel-base super alloy and high-speed milling of AISI D2 cold work tool steel. Comparative experiments were conducted under different cooling/lubrication conditions, i.e. dry cutting, minimal quantity lubrication (MQL), cooling air, and cooling air and minimal quantity lubrication (CAMQL). For this research, composite refrigeration method was adopted to develop a new cooling gas equipment which was used to lower the temperature of compressed gas. The significant experimental results were: (i) application of cooing air and CAMQL resulted in drastic reduction in tool wear and surface roughness, and significant improvement in chip shape in finish turning of Inconel 718, (ii) in the high-speed milling of AISI D2, cooling air cutting presented longer tool life and slightly higher surface roughness than dry cutting and MQL. Therefore, it appears that cooling air cutting can provide not only environment friendliness but also great improvement in machinability of difficult-to-cut materials.     

Wear of CBN tool in turning of silicon nitride with cryogenic cooling

This paper reports the wear characteristics of a CBN tool in the turning of an advanced structural ceramic (silicon nitride) under dry cutting and cryogenic cooling conditions. A cooling system is designed to control the cutting temperatures on the tool by circulating cryogenic coolant through a reservoir built on the top of the cutting tool. This arrangement maintains the tool's hot-strength at its desirable range to resist tool wear in the cutting process. Experiments show that the tool wear significantly reduces with cryogenic cooling. Finite element analysis is used to estimate cutting temperatures on the tool and to reveal the reasons for different wear characteristics in the two cases. The analysis shows that the maximum temperature on the tool falls from 1153°C (without liquid nitrogen cooling) to 829°C (with liquid nitrogen cooling).     

Machining and Phase Transformation Response of Room-Temperature Austenitic NiTi Shape Memory Alloy

This experimental work reports the results of a study addressing tool wear, surface topography, and x-ray diffraction analysis for the finish cutting process of room-temperature austenitic NiTi alloy. Turning operation of NiTi alloy was conducted under dry, minimum quantity lubrication (MQL) and cryogenic cooling conditions at various cutting speeds. Findings revealed that cryogenic machining substantially reduced tool wear and improved surface topography and quality of the finished parts in comparison with the other two approaches. Phase transformation on the surface of work material was not observed after dry and MQL machining, but B19′ martensite phase was found on the surface of cryogenically machined samples.     

Performance evaluation of solid lubricants in terms of machining parameters in turning

High speed machining of steel inherently generates large cutting temperatures, which not only reduce tool life but also impair the product quality. Application of cutting fluids influences the performance of machining because of its lubrication and cooling actions. Due to the hazards posed by conventional cutting fluids to ecology and health of the workers, there is a greater need to identify eco-friendly and user-friendly alternatives. Modern tribology has facilitated the use of effective unconventional methods like dry cutting, cryogenic cooling, minimum quantity lubrication and the use of solid lubricants. The present work features a specific study on the application of a solid lubricant mixture like Graphite in SAE 40 oil and boric acid in SAE 40 oil in turning of EN8 steel. Experimental results are encouraging with reduction in tool wear and surface roughness as compared to dry and wet machining.     

Machining of β-titanium-alloy Ti-10V-2Fe-3Al under cryogenic conditions: Cooling with carbon dioxide snow

Titanium alloys are widely used in applications that demand a good combination of high strength, good corrosion resistance and low mass. Beta-Titanium alloys offer the highest specific strength among titaniumbased materials. The mechanical properties lead to challenges in machining operations such as high process temperatures, high specific mechanical loads and rapidly increasing tool wear. The high chemical reactivity of titanium leads to rapidly developing flank and notch wear limiting cutting speeds and tool life. Applying industrial gases instead of conventional cooling and lubrication fluids promises increased productivity. In this work, the effectiveness of carbon dioxide snow (CO₂) as a coolant for turning Ti-10V-2Fe-3Al is analyzed. The carbon dioxide is provided in a pressurized gas bottle and is fed to the tool tip through holes in the tool holders clamping jaw. Compared to flood emulsion cooling the flank wear was uniform spreaded and tool life was increased by a factor of two even at higher cutting speeds. Tool-life-limiting notch wear and the burr formation at the workpiece have been suppressed.     

Capability of high pressure cooling in the turning of surface hardened piston rods

An experimental study was performed to investigate the capabilities of dry, conventional and high pressure cooling (HPC) in the turning of surface hardened piston rods used in fluid power applications. Machining experiments were performed using coated carbide tools at cutting speeds up to 160 m/min. The cooling capabilities are compared by monitoring of chip breakability, process regions of operability, cooling efficiency, tool wear, tool life and cutting forces. Test results showed that dry cutting could not be performed due to long and ductile chips that were formed for all investigated cutting conditions. In comparison to conventional cooling the significant increase of cutting speed and feed rate region of operability was recorded when machining with HPC. Tool life analysis proved a five times increase in tool life when machining with HPC. Furthermore HPC also improved chip breakability and reduced coolant consumption.     

Machining of hardened steel—Experimental investigations,performance modeling and cooling techniques: A review

The researchers have worked on many facets of machining of hardened steel using different tool materials and came up with their own recommendations. Researchers have tried to investigate the effects of cutting parameters, tool materials, different coatings and tool geometry on different machinability aspects like, the tool life, surface roughness, cutting forces, chip morphology, residual stresses and the tool–chip interface temperature under dry and/or semi-dry and/or flood cooling environment during machining of hardened steels while many of them have ventured to characterize the wear phenomenon. Good amount of research has been performed on an analytical and/or numerical and/or empirical modeling of the cutting forces, tool–chip interface temperature, and tool wear under orthogonal/oblique cutting conditions during machining of hardened steels. This paper presents a comprehensive literature review on machining of hardened steels using coated tools, studies related to hard turning, different cooling methods and attempts made so far to model machining performance(s) so as to give proper attention to the various researcher works.     

Some studies on high-pressure cooling in turning of Ti–6Al–4V

Titanium alloys are being increasingly employed in engineering and bio-medical applications, but their manufacturability via the cutting and grinding process is always a problem, which needs to be overcome. Inherent characteristics of Ti–6Al–4V alloy promote rapid tool wear, which needs to be curbed in order to attain high efficiency in metal cutting. Conventional or low-pressure cooling method fail to effectively conduct away the heat generated in the cutting zone, which is responsible for short tool life. High-pressure coolant jets were directed into the tool–chip interface to sufficiently penetrate and change the thermal, frictional and mechanical conditions in the cutting zone. High-pressure cooling using neat oil and water-soluble oil was undertaken and its effects on machining evaluation parameters such as chip form, chip breakability, cutting forces, coefficient of friction, contact length, tool life and surface finish of the finished workpiece were evaluated in comparison with those from the conventional cooling method. The results show that significant improvement in tool life and other evaluation parameters could be achieved utilising moderate range of coolant pressure.     

New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V

The use of cryogenic coolant in metal cutting has received renewed recent attention because liquid nitrogen is a safe, clean, non-toxic coolant that requires no expensive disposal and can substantially improve tool life. This work investigates the effectiveness of cryogenic coolant during turning of Ti-6Al-4V at a constant speed and material removal rate (125 m/min, 48.5 cm³/min) with different combinations of feed rate and depth of cut. It is found that the greatest improvement in tool life using cryogenic coolant occurs for conditions of high feed rate and low depth of cut combinations. However, this combination of machining parameters produces much shorter tool life compared to low feed rate and high depth of cut combinations. It is found that preventing heat generation during cutting is far more advantageous towards extending tool life rather than attempting to remove the heat with cryogenic coolant. Although cryogenic coolant is effective in extracting heat from the cutting zone, it is proposed that cryogenic coolant may limit the frictional heat generated during cutting and limit heat transfer to the tool by reducing the tool-chip contact length. The effect of cryogenic coolant on cutting forces and chip morphology is also examined.     

Mechanisms involved in the improvement of Inconel 718 machinability by laser assisted machining (LAM)

The aim of the present research work has been to gain a broader understanding of how or why laser assisted machining (LAM) improves machinability of Inconel 718, a hard-to-machine material of interest in the aeronautic industry. This has been accomplished by, first, running short run tests to determine the laser parameters and configuration for which highest force reductions are obtained and also to determine the effect of cutting parameters (feed, cutting speed and depth of cut) on force reduction. Secondly, long run tests have been performed in order to analyze process variables such as cutting forces, tool wear and surface roughness. Temperatures and hardness have been also measured in order to gain a broader perspective of the process.Experimental results have demonstrated that LAM improves machinability of Inconel 718 since machining forces and final surface roughness are reduced. The novelty reached with the present research work is the identification of three mechanisms associated to the laser heating as the responsible of this machinability improvement: material yield strength reduction, material base hardness reduction (only in precipitation hardened Inconel 718) and elimination of the work hardening generated in previous machining passes. The reduction of the work hardening leads also to a lower notch wear that limits the risk of sudden failure of the cutting tool and thus the wear mode is changed to flank wear, which leads to a controllable tool life and better surface roughness.     

The effects of cryogenic cooling on surface integrity in hard machining: A comparison with dry machining

This paper presents results of an experimental study of cryogenic machining of hardened AISI 52100 steel, focusing on surface integrity. Experiments were performed under dry and cryogenic cooling conditions using CBN tools varying cutting speeds, workpiece hardness and tool geometry. Surface integrity parameters (surface roughness, white layer thickness, residual stresses, metallurgical conditions including grain size, phase transformation, etc.) were investigated to establish the effects of cryogenic cooling on the surface integrity of the machined component, and results were compared with those from dry hard machining. Overall, cryogenic cooling provides improved surface integrity leading to extended product life and performance.     

Determining the influence of cutting fluids on tool wear and surface roughness during turning of AISI 304 austenitic stainless steel

Knowledge of the performance of cutting fluids in machining different work materials is of critical importance in order to improve the efficiency of any machining process. The efficiency can be evaluated based on certain process parameters such as flank wear, surface roughness on the work piece, cutting forces developed, temperature developed at the tool chip interface, etc. The objective of this work is to determine the influence of cutting fluids on tool wear and surface roughness during turning of AISI 304 with carbide tool. Further an attempt has been made to identify the influence of coconut oil in reducing the tool wear and surface roughness during turning process. The performance of coconut oil is also being compared with another two cutting fluids namely an emulsion and a neat cutting oil (immiscible with water). The results indicated that in general, coconut oil performed better than the other two cutting fluids in reducing the tool wear and improving the surface finish. Coconut oil has been used as one of the cutting fluids in this work because of its thermal and oxidative stability which is being comparable to other vegetable-based cutting fluids used in the metal cutting industry.     

Machinability improvement of titanium alloy (Ti–6Al–4V) via LAM and hybrid machining

Titanium alloy (Ti–6Al–4V) is one of the materials extensively used in the aerospace industry due to its excellent properties of high specific strength and corrosion resistance, but it also presents problems wherein it is an extremely difficult material to machine. The cost associated with titanium machining is also high due to lower cutting speeds (<60 m/min) and shorter tool life. Laser-assisted machining (LAM) and consequently hybrid machining is utilized to improve the tool life and the material removal rate. The effectiveness of the two processes is studied by varying the tool material and material removal temperature while measuring the cutting forces, specific cutting energy, surface roughness, microstructure and tool wear. Laser-assisted machining improved the machinability of titanium from low (60 m/min) to medium-high (107 m/min) cutting speeds; while hybrid machining improved the machinability from low to high (150–200 m/min) cutting speeds. The optimum material removal temperature was established as 250 °C. Two to three fold tool life improvement over conventional machining is achieved for hybrid machining up to cutting speeds of 200 m/min with a TiAlN coated carbide cutting tool. Tool wear predictions based on 3-D FEM simulation show good agreement with experimental tool wear measurements. Post-machining microstructure and microhardness profiles showed no change from pre-machining conditions. An economic analysis, based on estimated tooling and labor costs, shows that LAM and the hybrid machining process with a TiAlN coated tool can yield an overall cost savings of ～30% and ～40%, respectively.     

Machining Ti–6Al–4V alloy with cryogenic compressed air cooling

A new cooling approach with cryogenic compressed air has been developed in order to cool the cutting tool edge during turning of Ti–6Al–4V alloy. The cutting forces, chip morphology and chip temperature were measured and compared with those measured during machining with compressed air cooling and dry cutting conditions. The chip temperature is lower with cryogenic compressed air cooling than those with compressed air cooling and dry machining. The combined effects of reduced friction and chip bending away from the cutting zone as a result of the high-speed air produce a thinner chip with cryogenic compressed air cooling and a thicker chip with compressed air cooling compared to dry machining alone. The marginally higher cutting force associated with the application of cryogenic compressed air compared with dry machining is the result of lower chip temperatures and a higher shear plane angle. The tendency to form a segmented chip is higher when machining with cryogenic compressed air than that with compressed air and dry machining only within the ranges of cutting speed and feed when chip transitions from continuous to the segmented. The effect of cryogenic compressed air on the cutting force and chip formation diminishes with increase in cutting speed and feed rate. The application of both compressed air and cryogenic compressed air reduced flank wear and the tendency to form the chip built-up edge. This resulted in a smaller increase in cutting forces (more significantly in the feed force) after cutting long distance compared with that observed in dry machining.     

Laser-assisted machining of Inconel 718 with an economic analysis

Superalloys have high strengths at elevated temperatures, which make them attractive toward various applications and also make these materials difficult to machine at room temperature due to excessive tool wear and poor surface finish. Laser-assisted machining (LAM) offers the ability to machine superalloys more efficiently and economically by providing the local heating of the workpiece prior to material removal by a single point cutting tool.An existing transient, three-dimensional heat transfer model is modified for modeling LAM of Inconel 718. Suitable coating conditions are determined for increasing the laser absorptivity in metals and an approximate absorptivity value is determined. The thermal model is validated in axial and circumferential directions by temperature measurement using an infrared camera.The machinability of Inconel 718 under varying conditions is evaluated by examining tool wear, forces, surface roughness, and specific cutting energy. With increasing material removal temperature from room temperature to 620 °C, the benefit of LAM is demonstrated by a 25% decrease in specific cutting energy, a 2–3-fold improvement in surface roughness and a 200–300% increase in ceramic tool life over conventional machining. Moreover, an economic analysis shows significant benefits of LAM of Inconel 718 over conventional machining with carbide and ceramic inserts.