Hydrolysis and biodegradation studies of surface-active esters

Base-catalyzed hydrolysis, biodegradation, and enzyme-catalyzed hydrolysis of a series of four monoesters of tetra(ethylene glycol) have been investigated. The surfactants varied in substitution on the α-carbon of the acyl chain, from no substitution, to 2-methyl, to 2-ethyl, and on to 2,2-dimethyl. All surfactants were based on C₈-acids except the methyl-substituted, which was based on a C₇-acid. The hydrolysis was investigated using ¹H nuclear magnetic resonance. The surfactants showed a pronounced difference in stability with respect to type of substitution in the vicinity of the ester bond. In alka-line hydrolysis the most significant difference in reactivity lay between the surfactant with an ethyl group and the surfactant with a methyl group in the α-position of the acyl chain. However, in the biodegradation studies these surfactants broke down at almost exactly the same rate as the nonsubstituted surfactant. In the biodegradation test, the disubstituted surfactant deviated considerably. Two lipases, from Mucor miehei (MML) and Candida antarctica B (CALB), were used in the enzyme-catalyzed hydrolysis. The surfactant with no substitution was found to hydrolyze much faster than the other surfactants, and the hydrolytic activity of MML, but not CALB, increased in the presence of surfactant micelles.     

Synthesis,Micellization, and Surface Activity of Novel Linear-Dendritic Carboxylate Surfactants

Two generations of novel linear-dendritic carboxylate surfactants C₁₈-G₁-(COONa)₂ and C₁₈-G₂-(COONa)₄ have been synthesized by the divergent method and their structures are characterized by ¹H Nuclear Magnetic Resonance and Infrared analysis. The electrical conductivity measurement is used to measure the Krafft temperatures of C₁₈-G₁-(COONa)₂ and C₁₈-G₂-(COONa)₄, which are much smaller than those of the corresponding conventional surfactant sodium stearate. The markedly enhanced solubility of two linear-dendritic surfactants is ascribed to the high hydrophilicity of surfactant headgroups induced by the carboxylate and ester groups. The critical micelle concentration (CMC) values obtained from both the electrical conductivity and surface tension measurements indicate that the micellizations of linear-dendritic surfactants become favorable with the increase in the number of the surfactant headgroup. However, the surface activity parameters including the surface tension at the CMC, maximum surface excess, and minimum surface area reveal that C₁₈-G₁-(COONa)₂ exhibits greater efficiency in absorbing at the air/water interface compared to C₁₈-G₂-(COONa)₄, owing to their different steric repulsions of the surfactant headgroups. In addition, C₁₈-G₁-(COONa)₂ and C₁₈-G₂-(COONa)₄ have higher emulsifying ability than the conventional surfactants sodium stearate and sodium octadecyl sulfate.     

Micellization and Adsorption Behaviors of New Reactive Polymerizable Surfactants Based on Modified Nonyl Phenol Ethoxylates

The synthesis and characterization of a series of polymerizable surfactants based on alkyl phenol ethoxylate backbone and carboxylic or anhydride chain ends were investigated. Surface activities of these polymerizable surfactants were investigated to correlate their structure and their performances. The new bifunctional surfmers were prepared by reacting polyoxyethylene 4-nonyl-2-propylene-phenol nonionic reactive surfactants with maleic anhydride. The chemical structure of the prepared surfactants was characterized by ¹³C and ¹H NMR analyses. The surface activities of the modified polymerizable surfactants were measured from the adsorption isotherm measurements which were determined from the relationship between the concentrations and surface tension of surfactants in aqueous medium at different temperatures. Critical micelle concentration (CMC) values were determined for water soluble surfactants. It was found that CMC decreases with the incorporation of the anhydride and acid groups in the chemical structure of polyoxyethylene 4-nonyl -2-propylene-phenol nonionic surfactant. surface-active parameters such as area per molecule at the interface (A _min), surface excess concentration (Γ_max) and the effectiveness of surface tension reduction (π_CMC) were measured from the adsorption isotherms of the modified surfactants. Some thermodynamic data for the adsorption process were calculated and discussed. The data indicated that the new surfmers are more reactive than the simple polyoxyethylene 4-nonyl-2-propylene-phenol and more adsorbed at interfaces. We have performed a preliminary experiment to explore the emulsification efficiency of the newly synthesized reactive surfactants in equal volume oil–water emulsions. Different emulsion types and stabilities were obtained.     

Synthesis and Surface Properties of Novel Gemini Imidazolium Surfactants

Five new Gemini imidazolium surfactants were synthesized from imidazole and 1-bromoalkane (C₈, C₁₀, C₁₂, C₁₄, C₁₆) to get 1-alkylimidazole, which was further reacted with 1,3-dichloropropan-2-ol to form the surfactant molecule, 1,1′-(propane-1,3-diyl-2-ol) bis(3-alkyl-1H-imidazol-3-ium) chloride. The structures of the five new surfactants and intermediates were characterized by ¹H-NMR, ¹³C-NMR and IR spectra. Thermal properties of the five new surfactants were studied with thermogravimetric analysis and differential scanning calorimetry, the five new surfactants showed a transition from a crystalline phase to a thermotropic liquid–crystalline phase at around ca. 100 °C, which transformed to an isotropic liquid phase at around ca. 165 °C. The five new surfactants critical micelle concentrations (CMC) in the aqueous solutions were determined by surface tension and electrical conductivity methods. The surface tension measurements provided a series of parameters, including critical micelle concentration (CMC), surface tension at the CMC (γ _CMC), adsorption efficiency  (pC ₂₀), and effectiveness of surface tension reduction (π_CMC). In addition, with application of the Gibbs adsorption isotherm, maximum surface excess concentration (Γ_max) and minimum surface area/molecule (A_min) at the air–water interface were obtained. The parameters β (degree of counterion binding to micelles), ΔG _ads ^θ (Gibbs free energy of adsorption), and ΔG _mic ^θ (Gibbs free energy change of micellization) were also derived. The results indicated that the five new Gemini surfactants exhibited very low CMC and a good efficiency in lowering the surface tension of water. The foamability and foam stability of the five new surfactants were also examined at different CMC.     

Preparation and Characterization of C10–C14 Alkyl Cellulose Ester Sulfate Surfactant

The aim of this work is to synthesize surfactants based on cellulose with different molecular weights. Raw cotton cellulose was tailored into cellulose segments with different molecular weights by a hydrothermal process, then the average degree of polymerization (DP) was determined by viscosimetry and the molecular weight distribution was estimated by gel permeation chromatography. The C₁₀–C₁₄ alkyl cellulose ester sulfate surfactants were prepared by hydrophilic sulfonation and hydrophobic esterification. The surface tension of the surfactants solution was obtained by the Wilhelmy plate method. Results showed that the cellulose segments presented a broader distribution compared with the raw material. The critical micelle concentration (CMC) value decreased from 1.08 to 0.86 wt% as the hydrophobic chain length was increased from 10 to 14. The CMC values of cellulose surfactants with C₁₄-acyl chloride hydrophobization decreased from 1.32 to 0.86 wt% as the DP was decreased from 2,700 to 296.     

Ortho ester-based cleavable cationic surfactants

A new type of cleavable cationic surfactant, based on the ortho ester link, is described. Ortho ester amines with alkyl chain lengths from C₈ to C₁₆ were synthesized from a short-chain ortho ester, a fatty alcohol, and an amino acohol. The ortho ester amine was subsequently quaternized with methyl chloride, yielding a cationic surfactant. The structures were confirmed by ¹H and ¹³C nuclear magnetic resonance and the surface chemical properties were investigated by measuring both static and dynamic surface tensions. The results were compared to standard n-alkyl trimethyl ammonium bromides. The critical micelle concentrations were found to vary rather widely, whereas the surface tensions in some cases were comparatively low. The short alkyl chain ortho ester quaternaries were found to have low surface tensions at short surface ages and to induce rapid wetting of a hydrophobic surface in dynamic tests. Additionally, the new surfactants were found to hydrolyze rapidly under mild acidic conditions, as measured by both titation and monitoring of the dynamic surface tension. Further, they showed excellent long-term stability at pH 10 in dilute aqueous solutions. The effect of added electrolyte on rate of hydrolysis was also investigated. A marked enhancement in the hydrolysis rate was found when NaBr was added, whereas NaCl did not have the same effect. The new surfactants could potentially be used to provide temporary surfactant action in application areas such as disinfection, fabric care, personal care, chain lubrication, and mineral flotation as well as in textile processes such as dyeing or scouring.     

Properties of Sodium Methyl Ester Alpha-Sulfo Alkylate/Trimethylammonium Bromide Mixtures

The surface properties of binary mixtures of anionic sodium methyl ester ??-sulfo alkylate (C _m MES) and cationic alkyl trimethylammonium bromide (C _n TAB) of different carbon chain length have been studied in the present work. The critical micelle concentration (CMC) that was obtained from the plots of surface tension (??) versus concentration showed that mixed surfactants have CMC values that were about 10 times lower than their single components. The large negative values for both interaction parameters suggest the existence of strong synergism between the oppositely charged surfactant molecules. The effect of hydrocarbon chain length of either surfactant was also compared and results showed that the effect of cationic surfactant chain length dominated that of the anionic surfactants. It was also discovered that certain mixed surfactant combinations behave differently from the expected trend.     

Synthesis and Characterization of Novel Surfactants based on 2-Hydroxy-4-(Methylthio)Butanoic Acid Part 3: Microemulsions from Nonionic Sulfoxide Ester Surfactants

In this work, ester sulfoxide (ESO) surfactants based on 2-hydroxy-4-(methylthio) butyric acid are shown to have temperature-sensitive microemulsion phase behaviors. Both C10 (C₁₀ESO) and C12 (C₁₂ESO) surfactants studied contained one sulfoxide unit in the structure. Phase inversion temperatures (PIT) and interfacial tensions (IFT) between water-rich and oil-rich phases have been measured for ternary systems of water, oil, and sulfoxide surfactants. Hydrophilic–lipophilic deviation (HLD) parameters of these surfactants were obtained by fitting the experimental data to a semiempirical HLD equation. The characteristic surfactant parameter and temperature sensitivity of C₁₀ESO and C₁₂ESO surfactants were obtained and compared with similar ethoxylated alcohol surfactants. By comparing the characteristic parameters of these surfactants with those of ethoxylated alcohol surfactants, it was shown that one sulfoxide ester moiety is equally hydrophilic as approximately 5 ethylene oxide groups. The temperature sensitivity of the ESO was roughly a factor of four less than ethoxylated surfactants based on the temperature coefficient of the HLD equation.     

A Star-Shaped Anionic Surfactant: Synthesis,Alkalinity Resistance,Interfacial Tension and Emulsification Properties at the Crude Oil–Water Interface

In this research, a star‐shaped surfactant was synthesized through the chlorination reaction, alkylation reaction and sulfonation reaction of triethanolamine, which is composed of three hydrophobic chains and three sulfonate hydrophilic groups. The critical micelle concentration (CMC) of the surfactant was measured by the surface tension method, and the results showed that it had high surface activity with CMC of 5.53 × 10^?5 mol/L. The surfactant was superior in surface active properties to the reference surfactants SDBS and DADS‐C₁₂. The interfacial tension (IFT) of the studied crude oil–water system (surfactant concentration 0.1 g/L, NaOH concentration 0.5 g/L, and experimental temperature 50 °C) dropped to 1.1 × 10^?4 mN/m, which can fulfil the requirement of surfactants for oil displacement. An aqueous solution of the surfactant and crude oil was emulsified by shaking, which formed a highly stable oil‐in‐water (O/W) emulsion with particle size of 5–20 μm. The oil displacement effect was almost 12%.     

Advanced synthesis for monodisperse polymer nanoparticles in aqueous media with sub-millimolar surfactants

Highly monodisperse polystyrene nanoparticles with mean diameters of less than 100 nm are synthesized via aqueous emulsion polymerization using an amphoteric initiator (VA-057) in the presence of sub-millimolar concentrations of anionic surfactant. Since the net charge on the initiator is almost zero at neutral pH, the resultant latex particle size is mainly determined by surfactant adsorption. Polymerizations were performed in the presence of a range of anionic surfactants with differing critical micelle concentrations (CMC) by varying the concentrations of surfactant, initiator and monomer, and also the ionic strength. Sodium dodecyl benzene sulfonate (SDBS), sodium hexadecyl sulfate (SHS), and sodium octadecyl sulfate (SOS) have relatively low CMCs and so enable formation of highly monodisperse nanoparticles at relatively low (sub-millimolar) surfactant concentrations, C_S (i.e. below the CMC in each case). Empirically, it was found that the particle number, N_p, and coefficient of variation of the particle size, C_V, were strongly dependent on the C_S/CMC ratio: N_p increased almost in proportion with the square of this ratio, while the C_V exhibited a minimum at approximately C_S/CMC = 0.20. Higher ionic strength reduced the particle size, which is consistent with the above relationship because the addition of salt lowers the CMCs of ionic surfactants. Polymer latex particles produced using such formulations form highly regular, close-packed colloidal arrays.     

α-Sulfonato palmitic acid methyl ester-hexaoxyethylene monododecyl ether mixed surfactant system: Interfacial,thermodynamic, and performance property study

Interfacial, thermodynamic, and performance properties of aqueous binary mixtures of α-sulfonato palmitic acid methyl ester, C₁₄H₂₉CH(SO₃Na)COOCH₃(PES), and hexaoxyethylene monododecyl ether, CH₃(CH₂)₁₁(OCH₂CH₂)₆OH (C₁₂E₆), were investigated with tensiometric, conductometric, fluorimetric, and viscometric techniques. The critical micelle concentration (CMC), maximum surface excess, minimum area per molecule of surfactant at the air/water interface, and the thermodynamics of micellization and adsorption were determined. The CMC was very low for mixed systems, indicating probable use as a detergent with less effect on the environment because of surfactant biodegradability and less amount in the environment. The interaction parameter β^m, computed by using the theory of Rubingh and Maeda, indicated an attractive interaction (synergism) between the surfactant molecules, which was also confirmed by proton nuclear magnetic resonance studies in the mixed micelle. The micellar aggregation number (N _agg), determined by using a steady-state fluorescence quenching method at a total surfactant concentration of about ∼10 mM at 25°C, was almost independent of the surfactant mixture composition. The micropolarity and the binding constant (K _sv) for the C₁₂E₆/PES mixed system were determined by the ratio of the intensities (I ₁/I ₃) of the pyrene fluorescence emission spectrum, and the local microenvironment inside the micelle was found to be polar. The viscosity of the mixed system at all mole fractions suggested that mixed micelles are nonspherical in nature. The cloud point of oxyethylene group-containing surfactants was increased by the addition of PES. Foaming was temperature dependent, and a 1∶1 mixed system showed minimum foaming. All performance properties were composition dependent.     

Solubilization of phosphatidylcholine unilamellar liposomes caused by alkyl glucosides

Solubilizing alterations caused by a series of alkyl glucosides (alkyl chain lengths ranging from C₈ to C₁₂) in phosphatidylcholine (PC) unilamellar liposomes were investigated. Surfactant-to-phospholipid molar ratios (Re) and bilayer/aqueous phase partition coefficients (K) were determined by monitoring changes in static light scattering (SLS) of the system during solubilization. At the two interaction levels investigated (surfactant concentrations producing SLS values of 100 and 0% for each surfactant/PC system studied) the free surfactant concentration for each surfactant was always comparable to its critical micelle concentration (CMC). This indicates that liposome solubilization was mainly ruled by mixed micelle formation. A rise in CMC (or decrease in the surfactant alkyl chain length) resulted in an increase in the ability of these surfactants to saturate or solubilize PC liposomes and, inversely, in an abrupt decrease in their affinity with these bilayer structures. The overall balance of these opposite tendencies shows that the octyl glucoside had the highest ability to saturate and solubilize liposomes (lowest Re values), whereas the dodecyl glucoside exhibited the highest degree of partitioning into liposomes or affinity with bilayer structures (highest K values). From a practical viewpoint, the use of nonyl glucoside reduced approximately 2.5 times the concentration needed to saturate and solubilize 1.0 mM PC liposomes with respect to that needed using the conventional octyl glucoside.     

Extraction of Rare Earth Metals Using Liquid Surfactant Membranes Prepared by a Synthesized Surfactant

Abstract

Three surfactants, l-glutamic acid dioleyl ester ribitol (nonionic, 2C ₁₈Δ⁹ GE), l-glutamic acid dioleyl ester quaternary ammonium chloride (cationic, 2C ₁₈Δ⁹ GEC ₂ QA), and dioleyl dimethyl quaternary ammonium chloride (cationic, 2C ₁₈Δ⁹ QA) were synthesized for potential use in liquid membrane operations. These surfactants have strongly hydrophobic, twin oleyl chains as the hydrophobic moiety. Using the synthesized surfactants, extraction of rare earth metals was carried out by liquid surfactant membranes in a stirred tank. The extraction behavior of 12 kinds of rare earth metals was systematically studied with 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (commercial name: PC-88A) as a carrier. Different surfactants having an identical hydrophobic moiety can have significantly different behaviors in rare earth extractions by liquid surfactant membranes, where extraction efficiency appears to be governed by the nature of the interfacial microenvironment between oil and water. An interfacial reaction model which takes into account the adsorption of a surfactant at the interface has been proposed to evaluate the permeation rate of rare earth metals by liquid surfactant membranes. It was found that a cationic surfactant strongly enhances the extraction rate of rare earth metals compared with the conventional surfactant, Span 80. The cationic surfactant 2C ₁₈Δ⁹ GEC ₂ QA appears to be one of the best surfactants currently available for rare earth extraction by liquid surfactant membranes.     

Nonionic cleavable ortho ester surfactants

A new class of cleavable surfactants based on the ortho ester link is described. Ortho ester surfactants were synthesized from a short-chain ortho ester, a fatty alcohol, and a poly(ethylene glycol) monomethyl ether. The triple functionality of the ortho ester link results in a mixture of surface-active and nonsurface-active species. Structures were confirmed by ¹H and ¹³C nuclear magnetic resonance. Hydrolysis characteristics at pH values ranging from 2 to 8 were determined. It was shown that, after a steep rise, hydrolysis curves flattened out before complete hydrolysis was reached. Ortho ester surfactants hydrolyze more rapidly than corresponding acetal surfactants. Hydrolysis rates are higher for purified samples and at higher temeprature, while plateau levels are higher for the purified surfactant mixtures and at lower pH. The origin of these results is discussed. Data also indicate that the hydrolysis mechanism changes with pH. A test of the loss of emulsification capacity for an ortho ester surfactant with time at pH values from 2 to 11.5 and at 22 or 50°C was carried out, showing rapid breaking of the emulsion at mild acid conditions and a requirement of pH≥10 for long-term stability. Surface tension and critical micelle concentration were determined for some of the surfactant mixtures. It was demonstrated that ortho ester surfactants possess excellent biodegradation properties. The new surfactants are promising candidates for use in industrial processes where temporary surfactant action is required.     

Self-Assembly of Polyethylene Glycol Ether Surfactants in Aqueous Solutions: The Effect of Linker between Alkyl and Ethoxylate

The aqueous self-assembly behavior of two homologous series of poly(ethylene oxide) (PEO)-containing nonionic surfactants based on a C₁₀-Guerbet hydrophobe is reported. The two families of surfactants, alkyl ethoxylates and alkyl alkoxylates, are commercially available from BASF under the trade name Lutensol® XP-series and XL-series, respectively. The latter incorporate propylene oxide (PO) units in the surfactant chain. Dye solubilization was used to determine the critical micellization concentration (CMC) of each surfactant at 22 and 50 °C. The PO-containing alkyl alkoxylates displayed lower CMC values, which were also more sensitive to temperature. The Gibbs free energy, enthalpy, and entropy of micellization were computed from the CMC data and used to identify the contribution of each surfactant moiety (alkyl chain, PO unit, and PEO block) in controlling the CMC. The micellization properties are compared with compositionally similar surfactants with linear alkyl chains, yielding information about the effects of the Guerbet alkyl chain on micellization. Isothermal titration calorimetry was also used to characterize the CMC and enthalpy of micellization which generally compare well with the dye solubilization results. Cloud point data reveal nonmonotonic relationships for the Lutensol® surfactants with respect to composition, unlike linear alkyl chain surfactants. Finally, dilute solution viscosity measurements performed on some Lutensol® surfactants show a change in the slope, suggesting a structural change that tends to be more pronounced for surfactants with longer PEO blocks. The data presented herein enhance the understanding of surfactant structure–property relationships required for industrial formulation.     

Surface and Biocidal Properties of Gemini Cationic Surfactants Based on Propoxylated 1,6-Diaminohexane and Alkyl Bromides

Two new classes of gemini cationic surfactants—hexanediyl-1,6-bis[(isopropylol) alkylammonium] dibromide {in the abbreviation form: C_nC₆C_n[iPr-OH] and C_nC₆C_n[iPr-OH]₂; alkyl: C_nH_{2n + 1} with n = 9, 10, 12 and 14}—have been synthesized by interaction of alkyl bromides with N,N′-di-(isopropylol)-1,6-diaminohexane and N,N,N′,N′-tetra-(isopropylol)-1,6-diaminohexane. The surface tension, electrical conductivity, and dynamic light scattering (DLS) techniques were used to investigate the aggregation properties of the gemini cationic surfactants in aqueous solution. The formation of critical aggregates at two concentrations in an aqueous solution from obtained gemini cationic surfactants were determined via the tensiometric method. Thus, these gemini cationic surfactants start to form aggregates at concentrations well below their critical micelle concentrations (CMC). The surface properties and the binding degree (β) of the opposite ion were tested against the length of the surfactant hydrocarbon chain and the number of the isopropylol groups in the head group. By applying the DLS technique, it was explored that how the number of isopropylol groups in gemini cationic surfactants with C₁₂H₂₅ chain affects the sizes of micelles at concentrations greater than CMC. It was discovered that the obtained gemini cationic surfactants have a biocidal character.     

Synthesis and Properties of Dissymmetric Gemini Surfactants

A series of novel dissymmetric gemini surfactants, [C _m H_2m+1COOC₂H₄(CH₃)₂N(CH₂)₃N(CH₃)₂C₂H₄OOCC _n H_2n+1]Br₂ was synthesized and symbolized as m-s–n. The Krafft temperatures and surface tension curves of the dissymmetric gemini surfactants were measured using an electrical conductivity method and a drop volume method. The low Krafft temperatures indicate very good solubility of these esterquat gemini surfactants. With the increasing numbers of carbon atoms in the hydrophobic alkyl chain, the critical micelle concentration (CMC) and the minimum surface area (A _min) decrease, and the efficiency of surface tension reduction (pc₂₀) increases. With the same numbers of carbon atoms in the hydrophobic alkyl chain, the dissymmetric gemini surfactant has a lower CMC and a smaller A _min than the corresponding symmetric gemini surfactant due to the enhanced hydrophobic interactions.     

Surfactant properties of purified polyglycerol monolaurates

A series of purified polyglycerol monolaurates (PGML), such as di-, tri-, tetra-, and pentaglycerol monolaurates, were synthesized, and their surfactant properties in aqueous solutions were examined. The surfactant properties of PGML were compared with those of n-dodecyl polyoxyethylene monoethers (C₁₂EO_n) to examine the function of the hydrophilic part of these compounds. The critical micelle concentration (CMC) values and the surface tension at CMC of PGML and C₁₂EO_n increased linearly with an increase in the number of glycerol and oxyethylene units, respectively; the slope of the increase was greater for PGML than C₁₂EO_n. The minimum surface area per molecule of PGML was smaller than that of C₁₂EO_n at the air/aqueous solution interface. The initial foam heights of the surfactants at the CMC increased with an increase in the number of glycerol or oxyethylene units, and the foam heights of PGML were consistently higher and more stable than those of C₁₂EO_n. Detergency depended on a reduction in interfacial tension. Triglycerol monolaurate showed the lowest interfacial tension and the highest detergency among all the surfactants tested. Overall, the PGML showed better performance in all the surfactant properties tested than C₁₂EO_n. It is noteworthy that the surfactant properties of PGML having few glycerol units (di- to tetraglycerol monolaurates) are on par with those of C₁₂EO_n having many oxyethylene units (hexa- and octaoxyethylene). These results suggest that PGML having a secondary hydroxyl group on every glycerol unit of the hydrophilic part could be more hydrophilic than C₁₂EO_n; this characteristic feature guaranteed the superior surfactant properties of PGML.     

Synthesis and Surface Properties of Polyether-Based Silicone Surfactants with Different Siloxane Groups

A series of polyether-based silicone surfactants with different hydrophobic chains (trimethylsiloxy, triethylsiloxy, and triisopropylsiloxy) were synthesized. The molecular structures were confirmed using ¹H nuclear magnetic resonance (NMR), ¹³C NMR, ²⁹Si NMR, and fourier transform infrared spectroscopy (FT-IR). The effect of the siloxane groups on the physicochemical properties, surface tension (γ), critical micelle concentration (CMC), surface tension at the CMC (γ_CMC ), adsorption efficiency (pC₂₀), surface pressure at the CMC (π_CMC ), maximum surface excess (Γ_max ), single silicone surfactant molecule at the air/water interface (A_min ), and the standard free energy of adsorption (), of the polyether-based silicone surfactants was investigated. Results indicate that the polyether-based silicone surfactants can reduce the surface tension of water to approximately 25–31 mN m⁻¹ and the surface activity of silicone surfactants is enhanced with increasing branched trimethylsiloxyl and sterically hindered siloxane groups.     

Synthesis and Performance Evaluation of CO2/N2 Switchable Tertiary Amine Gemini Surfactant

A type of switchable tertiary amine Gemini surfactant, N,N′‐di(N,N‐dimethyl propylamine)‐N,N′‐didodecyl ethylenediamine, was synthesized by two substitution reactions with 3‐chloro‐1‐(N,N‐dimethyl) propylamine, bromododecane and ethylene diamine as main raw materials. The structure of the product was characterized by FTIR and ¹H‐NMR. We also investigated the surface tension when CO₂ was bubbled in different concentrations of surfactant solution and the influence of different CO₂ volumes on surface tension under a constant surfactant concentration. Finally the surface tension curve and the related parameters were acquired by surface tension measurements. The experimental results showed that the structure of the synthesized compounds were in conformity with the expected structure of the surfactant, and displayed a better surface activity after bubbling CO₂. The critical micelle concentration (CMC) surface tension at CMC (γ_cmc) pC₂₀ (negative logarithm of the surfactant's molar concentration C₂₀, required to reduce the surface tension by 20 mN/m) surface excess (Γ_max) at air/solution interface and the minimum area per surfactant molecule at the air/solution interface (A_min) were determined. Results indicate that the target product had good surface activity after bubbling CO₂.