Destruction of charge ordering phase in La_（0.4）Ca_（0.6）MnO_3 induced by low Cr doping

Polycrystalline samples of La<0.4>Ca<,0.6>Mn<,1-x>Cr<,x>O<,3> (x = 0.00, 0.02, 0.04, 0.06) were prepared by the solid state reaction method. The influence of Cr<'3+> substitution for Mn<'3+> on the magnetic property and charge ordering phase of La<0.4>Ca<,0.6>MnO<,3> was studied through the measurements of X-ray diffraction (XRD), magnetization-temperature (M-T) curves and electron spin resonance (ESR) spectra. The experimental results indicate that the mother's body of La<,0.4>Ca<,0.6>MnO<,3> has very complicated magnetic structure, exhibits charge ordering phase at 258 K, and shows long-range strongly correlated charge ordering-antiferromagnetism (CO-AFM) phase from 175 to 50 K.Spin glass state appears when the tempereature decreases to about 41 K. When the Cr substitution amount is x = 0.06, the charge ordering phase of the mother's body is de- stroyed, because the Cr<'3+> substitution for Mn<'3+> destroys the spin order of CE-type antiferromagnetism, and thus leads to the melting of charge ordering. It is verified experimentally that the strong coupling between charge order and spin order exists in the charge order system of CE-type antiferromagnetism     

Cr doping effect in B-site of La<Subscript>0.75</Subscript>Sr<Subscript>0.25</Subscript>MnO<Subscript>3</Subscript> on its phase stability and performance as an SOFC anode

La_0.75Sr_0.25Cr _y Mn_1−y O₃ (LSCM) (y = 0.0–0.6) composite oxides were synthesized by a complexing process of combining ethylene diamine tetraacetic acid (EDTA) and citrate. X-ray diffraction (XRD), temperature-programmed reduction, electrical conductivity, I–V polarization, and impedance spectroscopy were conducted to investigate the Cr doping effect of La_0.75Sr_0.25MnO₃ on its phase stability and electrochemical performance as a solid-oxide fuel cell (SOFC) anode. The chemical and structural stabilities of the oxides increased steadily with increasing Cr doping concentration, while the electrical conductivity decreased on the contrary. At y ≥ 0.4, the basic perovskite structure under the anode operating condition was sustained. a cell with 0.5-mm-thick scandia-stabilized zirconia electrolyte and La_0.75Sr_0.25Cr _y Mn_1−y O₃ anode delivered a power density of ∼15 mW·cm⁻² at 850°C.     

Enhancement of room-temperature magnetoresistance in La<Subscript>0.6</Subscript>Dy<Subscript>0.1</Subscript>Sr<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript>/Ag<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>

The samples of La0.6Dy0.1Sr0.3MnO3/(Ag2O)x/2(x = 0.00, 0.02, 0.04, 0.06, 0.08, 0.10, 0.20, 0.25, and 0.30) were prepared by using the solid-state reaction method.Their magnetic property, transport behavior, transport mechanism and magnetoresistance effect were studied through the measurements of magnetization-temperature(M-T) curves, ρ-T curves and the fitting of ρ-T curves.The results indicated that Ag could take part in the reaction when the doping amount is small.However, when the doping amount is compar...     

Enhancement of room-temperature magnetoresistance in La0.5Sm0.2Sr0.3MnO3/（Ag2O）x/2

La0.5Sm0.2Sr0.3MnO3/(Ag2O)x/2 (x = 0.00, 0.04, 0.08, 0.25, 0.30) samples were prepared by the solid-state reaction method, and their transport behaviors, transport mechanism, and magnetoresistance effect were studied through the measurement and fitting of ρ-T curves. The results show that the element Ag takes part in reaction when the doping amount is small. Ag is mainly distributed at the grain boundary of the host material and is in metallic state when the doping amount is relatively large; then the system becomes a two-phase composite. A small amount of Ag doping can apparently increase grain-boundary magnetoresistance induced by the spin-dependent scattering. The resistivity of the sample doped with 30 mol% Ag is one order of magnitude smaller than that of low-doped samples, and its magnetoresistance in the magnetic field of 0.5 T and at 300 K is strengthened apparently reaching 9.4%, which is connected not only with the improvement of the grain-boundary structure of the host material but also with the decrease of material resistivity.     

Production of TiO<Subscript>2</Subscript> from CaTiO<Subscript>3</Subscript> by alkaline roasting method

CaTiO3 was decomposed by alkaline roasting method for the production of TiO2.The process included alkaline roasting, water leaching and acid leaching steps.In the alkaline roasting step, the factors such as roasting temperature and NaOH/CaTiO3 molar ratio were investigated and 99.5% TiO2 could be extracted from CaTiO3.In addition, it is believed that only ion-exchange between Ca2+ and Na+ takes place, while the structure of TiO 32-in CaTiO3 was not destroyed during the roasting process.In the acid leaching ...     

Effect of NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> doping on the structure,magnetic properties and electrical properties of La<Subscript>0.7</Subscript>Ca<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript>

The (La_0.7Ca_0.3MnO₃)_1x /(NiFe₂O₄) _x (x = 0 to 0.09) composites were prepared using a conventional solid state reaction method. The structural, magnetic properties, and electrical properties of LCMO/NFO composites were investigated using X-ray diffraction, scanning electron microscopy, field cooled DC magnetization, and magnetoresistance (MR) measurements. The resistivity measured as a function temperature demonstrates that the pure LCMO and x = 0.01 samples display metal to semiconductor transitions. However, the composites of x > 0.03 samples clearly present the electrical behavior as an insulator/semiconductor type behavior. It was observed that the resistivity of the samples increased systemically with an increase of the NFO content. From the MR measurements, it was found that the MR effect is enhanced for x = 0.01 with a NFO composition. In all, the spin-polarized tunneling and the spin-dependent scattering may be beneficial for an improved low-field magnetoresistance effect. These phenomena can be explained by the segregation of a new phase related to NFO at the grain boundaries or surfaces of the LCMO grains.     

Roles of Te and Mn in the two phases of manganite with nominal composition La_（0.6）Sr_（0.1）Te_xMnO_3

Powder samples with nominal composition La<,0.6>Sr<,0.1>Te<,x>MnO<,3> (x = 0.00, 0.05, 0.10, 0.15, 0.20) were prepared using the sol-gel method with thermal treatment up to 1473 K. On the basis of powder X-ray diffraction (XRD), thermogravimetric and magnetic measurements, it was found that almost all of the Te and a few of the Mn ions were lost from the samples when they were calcined at 1473 K. The reason for the Te loss and a quantitative phase analysis for the samples calcined at 1473 K are discussed in detail.     

Effect of Dy doping on magnetism of La<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>CoO<Subscript>3</Subscript> system

The effect of Dy doping on magnetism of La0. 7Sr0. 3CoO3 system was studied through the measurements of M-T curves and M-H curves. The results show that with Dy content increasing, Tc decreases, M weakens, the coercive force strengthens, and the samples exhibit the abnormal phenomenon that M increases continuously with T decreasing in low temperature range. Research indicates that the variation of magnetism in the system comes from the changes of lattice parameters and magnetic environment caused by Dy doping and from the spin-state transition of Co ions induced by Dy ions.     

Effect of yttrium doping on the resistivity and magnetoresistance of La<Subscript>0.80</Subscript>Sr<Subscript>0.20</Subscript>MnO<Subscript>3</Subscript>

The temperature and magnetic field dependence of resistivity of crystals of nominal compositions of La_0.75Y_0.05Sr_0.20MnO₃ grown by floating zone method at different growth rates are studied. The yttrium doping is found to result in the decrease of Curie temperature, suppression of the Pnma-R $ \bar 3 $ \bar 3 c structural transition, increase of resistivity and magnetoresistance. It is shown that the physical properties of the manganites studied are determined by not only the nominal composition but also the growth rate.     

Influence of Sb<Subscript>2</Subscript>O<Subscript>3</Subscript> doping on the properties of KBT-NBT-BT lead-free piezoelectric ceramics

0.144(K0.5Bi0.5)TiO3-0.85(Na0.5Bi0.5)TiO3-0.006BaTiO3(KBT-NBT-BT) lead-free piezoelectric ceramics were prepared using a conventional solid state method.The influence of Sb2O3 doping on the crystal phase,surface microstructure and properties of the KBT-NBT-BT lead-free piezoelectric ceramics were investigated using X-ray diffraction(XRD),scanning electron microscope(SEM) and other analytical methods.The results show that all compositions are of pure perovskite structure solid states.Sb2O3 doping does not influence the microstructure of KBT-NBT-BT lead-free piezoelectric ceramics obviously in the Sb2O3 doping range of 0.1-0.5 wt.%.Sb2O3 functions as a donor when doped small amount,while functions as a acceptor when doped large amount.The piezoelectric strain constant(d33) increases first and then decreases;the dielectric constant(ε3T3/ε0) and the dielectric loss(tanδ) decrease continuously when the amount of Sb2O3 dopant increases.When the doping amount of Sb2O3 is 0.1 wt.%,the KBT-NBT-BT piezoelectric ceramics with good comprehensive properties are obtained,whose d33,ε3T3/ε0 and tanδ are 147 pC/N,1510 and 4.2%,respectively.     

Effects of dopant content on optical and electrical properties of In<Subscript>2</Subscript>O<Subscript>3</Subscript>: W transparent conductive films

The In2O3:W (IWO) films with different W content were deposited on glass substrate using direct current sputtering method. The structure, surface morphology, and optical and electrical properties were investigated. Results showed that both the carrier concentration and carrier mobility were increased with the doping of W. The IWO film with the lowest resistivity of 1. 0× 10-3 Ω· cm, highest carrier mobility of 43. 7 cm2. W-1. s-1 and carrier concentration of 1. 4× 1020 cm-3 was obtained at the content of 2. 8 wt. ％. The average optical transmittance from 300 nm to 900 nm reached 87. 6％.     

Phase Diagram of the Quaternary Al(NO<Subscript>3</Subscript>)<Subscript>3</Subscript>-Cu(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-Zn(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-H<Subscript>2</Subscript>O System

The phase diagram of the H₂O-Zn(NO₃)₂-Al(NO₃)₃-Cu(NO₃)₂ quaternary system at 30 °C has been established by using the conductivity measurements. The solid-liquid equilibria of the H₂O-Zn(NO₃)₂-Al(NO₃)₃, H₂O-Zn(NO₃)₂-Cu(NO₃)₂, H₂O-Al(NO₃)₃-Cu(NO₃)₂ ternary systems and two isoplethic sections were determined experimentally. The solid phases in equilibrium with the saturated solution are the tri- and hemipentahydrate of copper nitrate, the hexahydrate α and β of the zinc nitrate and the nonahydrate of aluminum nitrate. The copper and zinc nitrates are relatively soluble in opposition to the aluminum nitrate which presents some important precipitation domains.     

Preparation and characterization of nanostructured Bi<Subscript>2</Subscript>Se<Subscript>3</Subscript> and Sn<Subscript>0.5</Subscript>-Bi<Subscript>2</Subscript>Se<Subscript>3</Subscript>

Nanostructured Bi₂Se₃ and Sn_0.5-Bi₂Se₃ were successfully synthesized by hydrothermal coreduction from SnCl₂·H₂O and the oxides of Bi and Se. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and field emission scanning electron microscope (FESEM). Bi₂Se₃ powders obtained at 180°C and 150°C consist of hexagonal flakes of 50–150 nm in side length and nanorods of 30–100 nm in diameter and more than 1 μm in length. The product obtained at 120°C is composed of thin irregular nanosheets with a size of 100–200 nm and several nanometers in thickness. The major phase of Sn_0.5-Bi₂Se₃ synthesized at 180°C is similar to that of Bi₂Se₃. Sn_0.5-Bi₂Se₃ powders are primarily nanorod structures, but small amount of powders demonstrate irregular morphologies.     

Up-Date of a Thermodynamic Database of the ZrO<Subscript>2</Subscript>-Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>-Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> System for TBC Applications

The thermodynamic database of the ZrO₂-Gd₂O₃-Y₂O₃-Al₂O₃ system is up-dated taking into account new data on lattice stabilities of ZrO₂, Gd₂O₃ and Y₂O₃ and heat capacity measurements for the monoclinic phase Gd₄Al₂O₉ and phase with garnet structure Gd₃Al₅O₁₂. New data for the heat capacities of Gd₂Zr₂O₇ (pyrochlore) and GdAlO₃ (perovskite) as well as on the enthalpy of formation of fluorite solid solutions (Zr_1−x Gd _x )O_2−x/2 were found to be in good agreement with calculated results. In comparison with the previous assessment, taking into account new experimental data resulted in a change of the melting character of the Gd₄Al₂O₉ phase from a peritectic one to a congruent one in the Gd₂O₃-Al₂O₃ system. Correspondently, in the ternary system ZrO₂-Gd₂O₃-Al₂O₃, the melting character of the three-phase assemblage Gd₂O₃ (B), Gd₄Al₂O₉ and GdAlO₃ changed from eutectic to transition type U. The T ₀-lines for T/M and F/T diffusionless transformations and driving force of partitioning to equilibrium assemblage T + F were calculated in the ZrO₂-Gd₂O₃-Y₂O₃ system.     

Thermodynamic Assessment of PrCl<Subscript>3</Subscript>-CaCl<Subscript>2</Subscript> and NdCl<Subscript>3</Subscript>-CaCl<Subscript>2</Subscript> Systems

By using the CALPHAD technique, an assessment of the binary PrCl₃-CaCl₂ and NdCl₃-CaCl₂ systems have been carried out. From measured phase equilibrium data and experimental integral properties, the PrCl₃-CaCl₂ and NdCl₃-CaCl₂ phase diagrams were optimized and calculated. A set of thermodynamic functions has been optimized based on an interactive computer-assisted analysis. The calculated results by present method agree well with the experimental data.     

Effects of structural disordering in the manganite La<Subscript>0.825</Subscript>Ba<Subscript>0.175</Subscript>MnO<Subscript>3</Subscript>

Neutron and X-ray diffraction have been used to study the structural state of polycrystalline samples of the perovskite-like manganite La_0.825Ba_0.175MnO₃ with different concentrations of antisite defects produced by fast-neutron irradiation. It has been established that the concentration of antisite defects depends linearly on the fraction of the sample volume affected by cascades of atom-atom displacements, reaching at high fluences a value equal to 0.0875, which is “limiting” for a given composition. The formation of antisite defects is accompanied by the appearance of significant static uncorrelated ion displacements, which for oxygen ions become greater than their tilting displacements. It has been shown that in this case, the tilting mode ?, which forms the rhombohedral structure of the manganite, is not destructed completely, although the magnitude of correlated tilting displacements decreases noticeably.     

Studies on Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/ZrO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> high K gate dielectrics applied in a fully depleted SOI MOSFET

Al₂O₃/ZrO₂/Al₂O₃ gate stacks were prepared on ultrathin SOI (Silicon on insulator) substrates by ultrahigh vacuum electron beam evaporation and post-annealed in N₂ at 450°C for 30 min. Three clear nanolaminate layered structure of Al₂O₃(2.1 nm)/ZrO₂(3.5 nm)/Al₂O₃(2.3 nm) was observed with a high-resolution cross-sectional transmission electron microscope (HR-XTEM). High frequency capacitance voltage (C-V) characteristics of a fully depleted (FD) SOI MOS capacitor at 1 and 5 MHz were studied. The minority carriers determine the high frequency C-V properties, which is opposite to the case of bulk MOS capacitors. The series resistance of the SOI substrate is found to be the determinant factor of the high frequency characteristics of FD SOI MOS capacitors. This article is based on a presentation in “The 7th Korea-China Workshop on Advanced Materials” organized by the Korea-China Advanced Materials Cooperation Center and the China-Korea Advanced Materials Cooperation Center, held at Ramada Plaza Jeju Hotel, Jeju Island, Korea on August 24≈27, 2003.     

Microstructure and microwave dielectric properties of ZnO-B2O3 added （Ca0.254Li0.19Sm0.14）TiO3 ceramics

The effects of ZnO-B2O3 (ZB2) on the sintering behavior and microwave dielectric properties of (Ca0.254Li0.19Sm0.14)TiO3 ceramics were investigated.The densities of the specimens reached the maximum value by adding 3 wt.% ZB2 and then decreased.The sintering temperature of the specimens was lowered from 1300 to 1100°C without degradation of the microwave dielectric properties.The (Ca0.254Li0.19Sm0.14)TiO3 + 3 wt.% ZB2 sintered at 1100°C for 3 h showed good microwave dielectric properties,εr = 108.2,Qf = 6545 GHz,and τf = 6.5 ppm/°C,respectively,indicating that ZB2 was an effective sintering aid to improve the densification and microwave dielectric properties of (Ca0.254Li0.19Sm0.14)TiO3 ceramics.     

Structure and electrical resistance of dispersion-strengthened vacuum-deposited Cu–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposites

Methods of X-ray diffraction and transmission electron microscopy were used to study the microstructure of dispersion-strengthened Cu-Al₂O₃ nanocomposites obtained by the method of simultaneous deposition of Cu and Al₂O₃ from the vapor phase. The effect of the size of particles of the oxide (Al₂O₃) and of their content on the electrical resistance of the composite has been considered. The results obtained make it possible to suppose that the main structural factor that determines the electrical resistance of the composite are nanodispersed particles of Al₂O₃ with a size of less than 20 nm.     

Surface modification of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> with Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> for lithium ion batteries

Cr 2 O 3-coated LiNi 1/3 Co 1/3 Mn 1/3 O 2 cathode materials were synthesized by a novel method. The structure and electrochemical properties of prepared cathode materials were measured using X-ray diffraction (XRD), scanning electron microscopy (SEM), charge-discharge tests, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The measured results indicate that surface coating with 1.0 wt% Cr 2 O 3 does not affect the LiNi 1/3 Co 1/3 Mn 1/3 O 2 crystal structure (α-NaFeO 2 ) of the cathode material compared to the pristine material, the surfaces of LiNi 1/3 Co 1/3 Mn 1/3 O 2 samples are covered with Cr 2 O 3 well, and the LiNi 1/3 Co 1/3 Mn 1/3 O 2 material coated with Cr 2 O 3 has better electrochemical performance under a high cutoff voltage of 4.5 V. Moreover, at room temperature, the initial discharging capacity of LiNi 1/3 Co 1/3 Mn 1/3 O 2 material coated with 1.0 wt.% Cr 2 O 3 at 0.5C reaches 169 mAh·g 1 and the capacity retention is 83.1% after 30 cycles, while that of the bare LiNi 1/3 Co 1/3 Mn 1/3 O 2 is only 160.8 mAh·g 1 and 72.5%. Finally, the coated samples are found to display the improved electrochemical performance, which is mainly attributed to the suppression of the charge-transfer resistance at the interface between the cathode and the electrolyte.