Hydrothermal synthesis and electrochemical capacitance of RuO2·xH2O loaded on benzenesulfonic functionalized MWCNTs

Amorphous RuO₂·xH₂O was well coated on the benzenesulfonic functionalized multi-wall carbon nanotubes (f-MWCNTs) successfully via hydrothermal method. The decorated benzenesulfonic groups served as a bifunctional role both for solubilizing and dispersing MWCNTs into aqueous solution and for tethering Ru³⁺ precursor to facilitate the following uniform chemical deposition of RuO₂·xH₂O. The electrochemical performance of RuO₂/f-MWCNTs and utilization of RuO₂·xH₂O were evidenced by cyclic voltammetry and galvanostatic charge/discharge tests. The specific capacitance of 1143 Fg⁻¹ for RuO₂·xH₂O was obtained from RuO₂/f-MWCNTs with 32 wt.% RuO₂·xH₂O, which was much higher than that of just 798 Fg⁻¹ for the RuO₂/p-MWCNTs. Even though the RuO₂·xH₂O loading increases to 45 wt.%, the utilization of RuO₂·xH₂O still possesses as high as 844.4 Fg⁻¹, indicating a good energy capacity in the case of high loading.     

Soft template synthesis of mesoporous Co3O4/RuO2·xH2O composites for electrochemical capacitors

Co₃O₄/RuO₂·xH₂O composites with various Ru content (molar content of Ru = 5%, 10%, 20%, 50%) were synthesized by one-step co-precipitation method. The precursors were prepared via adjusting pH of the mixed aqueous solutions of Co(NO₃)₂·6H₂O and RuCl₃·0.5H₂O by using Pluronic123 as a soft template. For the composite with molar ratio of Co:Ru = 1:1 annealed at 200 °C, Brunauer-Emmet-Teller (BET) results indicated that the composite showed mesoporous structure, and the specific surface area of the composite was as high as 107 m² g⁻¹. The electrochemical performances of these composites were measured in 1 M KOH electrolyte. Compared with the composite prepared without template, the composite with P123 exhibited a higher specific capacitance. When the molar content of Ru was rising, the specific capacitance of the composites increased significantly. It was also observed that the crystalline structures as well as the electrochemical activities were strongly dependent on the annealing temperature. A capacitance of 642 F/g was obtained for the composite (Co:Ru = 1:1) annealed at 150 °C. Meanwhile, the composites also exhibited good cycle stability. Besides, the morphologies and textural characteristic of the samples were also investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM).     

Effects of substrates on the capacitive performance of RuOx·nH2O and activated carbon-RuOx electrodes for supercapacitors

The electrochemical energy storage and delivery on the electrodes composed of hydrous ruthenium oxide (RuO_x·nH₂O) or activated carbon-hydrous ruthenium oxide (AC-RuO_x) composites are found to strongly depend on the substrate employed. The contact resistance at the active material-graphite interface is much lower than that at the active material-stainless steel (SS) mesh interface. Thin films of gold plus RuO_x·nH₂O deposited on SS meshes (RuO_x/Au/SS) are found to greatly improve the poor contact between SS meshes and electrode materials. The maximum specific capacitance (C_S,RuOx) of RuO_x·nH₂O, 1580 F g⁻¹ (measured at 1 mV s⁻¹), very close to the theoretic value, was obtained from an AC-RuO_x/RuO_x/Au/SS electrode with 10 wt.% sol-gel-derived RuO_x·nH₂O annealed in air at 200 °C for 2 h. The highly electrochemical reversibility, high-power characteristics, good stability, and improved frequency response of this AC-RuO_x/RuO_x/Au/SS electrode demonstrate its promising application potential in supercapacitors. The ultrahigh specific capacitance of RuO_x·nH₂O probably results from the uniform size distribution of RuO_x·nH₂O nanoparticles, ranged from 1.5 to 3 nm which is clearly observed from the high-resolution transmission electron microscopy (HRTEM).     

RuO2·xH2O/NiO composites as electrodes for electrochemical capacitors: Effect of the RuO2 content and the thermal treatment on the specific capacitance

RuO₂·xH₂O/NiO composites having RuO₂ contents in the range 0-100 wt.% have been prepared by a co-precipitation method. Structural, microstructural and textural transformations after heating the as-prepared composites at 200 and 600 °C have been followed by X-ray diffraction, scanning electron microscopy (SEM) and nitrogen adsorption/desorption isotherms. At 200 °C the composites are made of micrometric particles in which nanometric crystallites of the two oxides are aggregated. The composites show microporosity (0.02-0.10 cm³/g), mesoporosity (0.07-0.12 cm³/g) and relatively high specific surface area (62-309 m²/g). At 600 °C the composites are fully dehydrated and RuO₂ has crystallized and segregated. Microporosity and mesoporosity as well as specific surface area are strongly decreased. Specific capacitance and specific surface area of the composites heated at 200 and 600 °C have been measured and discussed on the basis of the RuO₂ content. For comparison the specific capacitance and specific surface area of mixtures of NiO and RuO₂·xH₂O (or RuO₂) have been taken as references. The higher specific capacitance of the 200 °C-heated composites compared to the 600 °C-heated ones is due to the higher specific surface area of the former and the higher pseudocapacitance of RuO₂·xH₂O compared to RuO₂. The discussion reported in this work can be applied to other composites such as RuO₂·xH₂O/carbon and RuO₂·xH₂O/other oxides.     

Two-step hydrothermal synthesis of Ru-Sn oxide composites for electrochemical supercapacitors

A two-step hydrothermal process was developed to synthesize hydrous 30RuO₂-70SnO₂ composites with much better capacitive performances than those fabricated through the normal hydrothermal process, co-annealing method, or modified sol-gel procedure. A very high specific capacitance of RuO₂ (C_S,Ru), ca. 1150 F g⁻¹, was obtained when this composite was synthesized via this two-step hydrothermal process with annealing in air at 150 °C for 2 h. The voltammetric currents of this annealed composite were found to be quasi-linearly proportional to the scan rate of CV (up to 500 mV s⁻¹), demonstrating its excellent power property. From Raman, UV-vis spectroscopic and TEM analyses, the reduction in mean particulate size is clearly found for this two-step oxide composite, attributable to the co-precipitation of (Ru_δSn_1−δ)O₂·xH₂O onto partially dissolved SnO₂·xH₂O and the formation of (Ru_δSn_1−δ)O₂·xH₂O crystallites in the second step. This effect significantly promotes the utilization of RuO₂ (i.e., very high C_S,Ru). The excellent capacitive performances, very similar to that of RuO₂·xH₂O, suggest the deposition of RuO₂-enriched (Ru_δSn_1−δ)O₂·xH₂O onto SnO₂·xH₂O seeds as well as the individual formation of (Ru_δSn_1−δ)O₂·xH₂O crystallites in the second hydrothermal step.     

Hydrothermal synthesis of binary Ru-Ti oxides with excellent performances for supercapacitors

Hydrous, crystalline, binary (Ru-Ti)O₂·nH₂O with compositions equal to the ratios of metallic ions in the precursor solutions are successfully synthesized by a mild hydrothermal process. The maximum utilization of RuO₂·nH₂O (ca. 793 F/g) occurs at the composition of 60 M% TiO₂·nH₂O although phase separation is clearly found for this TiO₂-enriched binary oxides. The nano-structured architecture with a high BET surface area (ca. 253 m²/g) of the hydrothermal-derived (Ru-Ti)O₂·nH₂O with annealing at 200 °C favors the physical adsorption of water and maintains a high water content which is novel and never found before. Due to this novel nanostructure, the annealed (Ru-Ti)O₂·nH₂O synthesized by means of the hydrothermal process exhibits excellent performances (i.e., high utilization of RuO₂, high power property, and long cycle life) for supercapacitors.     

Single crystal nanobelts of V3O7·H2O: A lithium intercalation host with a large capacity

In this study, single crystal V₃O₇·H₂O nanobelts were successfully synthesized using a simple hydrothermal route, in which templates or catalysts were absent. The synthesized V₃O₇·H₂O nanobelts are highly crystalline and have lengths up to several tens of micrometers. The width and thickness of the nanobelts are found to be about 30-50 and 30 nm, respectively. A lithium battery using V₃O₇·H₂O nanobelts as the positive electrode exhibits a high initial discharge capacity of 409 mAh g⁻¹, corresponding to the formation of Li_xV₃O₇·H₂O (x = 4.32). Such a high degree of electrochemical performance is attributed to the intrinsic properties of the single-crystalline V₃O₇·H₂O nanobelts.     

Electrochemical capacitance of nanoporous hydrous RuO2 templated by anionic surfactant

The nanoporous RuO₂·3.38H₂O was synthesized with a surfactant template using sodium dodecyl sulfate. The surface area of the material amounted to 220 m² g⁻¹ while the maximum specific capacitance obtained was 870 Fg⁻¹ at a scan rate of 10 mV s⁻¹. The specific capacitance of nanoporous RuO₂·3.38H₂O electrode exhibits enhancement, compared with other porous RuO₂ materials synthesized by different methods. The nanoporous RuO₂·3.38H₂O is a very promising material for high performance capacitance.     

Capacitive and textural characteristics of hydrous manganese oxide prepared by anodic deposition

The amorphous hydrous manganese oxide (denoted as a-MnO_x·nH₂O) was anodically deposited from the MnSO₄ solutions of various pH values. The capacitive characteristics and stability of this oxide without and with annealing in air for 2 h up to 400 °C were systematically investigated in aqueous electrolytes through means of cyclic voltammetry (CV) and the constant-current charge-discharge method. The redox properties of a-MnO_x·nH₂O were strongly affected by the electrolytes employed and this oxide exhibited ideally capacitive behavior in 0.1 M Na₂SO₄ and 0.3 M KCl. The stability of this amorphous hydrous oxide was enhanced by the annealing treatment while its capacitance was gradually decreased with increasing the annealing temperature. The amorphous structure and surface morphologies of a-MnO_x·nH₂O with annealing at different temperatures were, respectively, examined in terms of the X-ray diffraction (XRD) patterns and scanning electron microscopic (SEM) photographs. The oxidation states of these a-MnO_x·nH₂O deposits were studied by X-ray photoelectron spectroscopy (XPS).     

Synthesis and characterization of ZnxMg1 − xGa2O4:Co fabricated by low-temperature burning method

A series of Zn_xMg_1 − xGa₂O₄:Co²⁺ spinels (x = 0, 0.25, 0.5, 0.75, and 1.0) was successfully produced through low-temperature burning method by using Mg(NO₃)₂·4H₂O, Zn(NO₃)₂·6H₂O, Ga(NO₃)₃·6H₂O, CO(NH₂)₂, NH₄NO₃, and Co(NO₃)₂·6H₂O as raw materials. The product was characterized by X-ray diffraction, transmission electron microscopy, and photoluminescence spectroscopy. The product was not merely a simple mixture of MgGa₂O₄ and ZnGa₂O₄; rather, it formed a solid solution. The lattice constant of Zn_xMg_1 − xGa₂O₄:Co²⁺ (0 ≤ x ≤ 1.0) crystals has a good linear relationship with the doping density, x. The synthesized products have high crystallinities with neat arrays. Based on an analysis of the form and position of the emission spectrum, the strong emission peak around the visible region (670 nm) can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴A₂(⁴F)] of Co²⁺ in the tetrahedron. The weak emission peak in the near-infrared region can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴T₂(⁴F)] of Co²⁺ in the tetrahedron.     

Anodic deposition of hydrous ruthenium oxide for supercapaciors: Effects of the AcO concentration, plating temperature, and oxide loading

Effects of the sodium acetate (NaCH₃COO, denoted as NaAcO) concentration, plating temperature, and oxide loading on the pseudocapacitive characteristics of hydrous ruthenium oxide (denoted as RuO₂·xH₂O) films anodically plated from aqueous RuCl₃·xH₂O media were systematically investigated in this work. The electrochemical behavior of RuO₂·xH₂O with annealing in air at 200 °C for 2 h is approximately independent of the NaAcO concentration and plating temperature although a negative shift in the onset and peak potentials of deposition with rising the plating temperature is found. The morphologies and adhesion of RuO₂·xH₂O deposits strongly depend on the deposition rate which is obviously influenced by varying the above two deposition variables. The specific capacitance of RuO₂·xH₂O is monotonously decreased from 760 to 505 F g⁻¹ when the oxide loading is gradually increased from 0.34 to 1.0 mg cm⁻², due to the longer pathways of both electrons and protons during the redox transitions. The XRD and Raman spectroscopic analyses reveal the extremely localized crystalline nature of as-deposited RuO₂·xH₂O. All RuO₂·xH₂O deposits show the ideal pseudocapacitive characteristics, definitely illustrating the merits of RuO₂·xH₂O prepared by anodic deposition without considering the advantages of its simplicity, one-step, reliability, low cost, and versatility for electrode preparation.     

Ruthenium oxide/carbon composites with microporous or mesoporous carbon as support and prepared by two procedures. A comparative study as supercapacitor electrodes

Composites are prepared by deposition of nanoparticles of RuO₂·xH₂O (1-4 nm) on two carbons: microporous carbon (1.3 nm of average micropore size) and mesoporous carbon (11 nm of average mesopore size). Two-preparation procedures are used: (i) procedure A consisting of repetitive impregnations of the carbons with RuCl₃·0.5H₂O solutions, and (ii) procedure B based on impregnation of the carbons with Ru(acac)₃ vapour. The procedure B leads to supported RuO₂·xH₂O particles that appear more crystalline than those obtained by the procedure A. Specific capacitance and specific surface area of the composites are discussed as functions of the RuO₂ content, and different dependences for the composites derived from the two carbons are found. Mesoporous carbon is better support than microporous carbon. Procedure A leads to supported RuO₂·xH₂O particles with higher specific capacitance than the particles deposited by procedure B.     

Development of ceramic electrochemical sensor based on Bi2Ru2O7+x − RuO2 sub-micron oxide sensing electrode for water quality monitoring

Sub-micron Bi₂Ru₂O_7+x + RuO₂ oxide sensing electrodes (SE) for water quality sensors were prepared on platinised ceramic substrate of the sensor. Their morphology was analysed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray analysis (EDX). Sensing properties of the Bi₂Ru₂O_7+x + RuO₂-SE were investigated for potentiometric detection of pH and dissolved oxygen (DO) in water in the temperature range of 4–30 °C. Sensor was capable to measure DO from 0.5 to 8.0 ppm and pH from 2.0 to 13.0, respectively. The obtained results show acceptable linearity of the measuring characteristics. Long-term stability trial for Bi₂Ru₂O_7+x + RuO₂-SE revealed that bio-fouling can be one of the main destructive factors affecting the performance of the sensors in the long run. The screen-printing technology used in the multi-sensory implementation provides fundamental properties of miniaturization, reasonable accuracy and low cost.     

Lithium insertion property of Li2 2V2O5·nH2O

Lithium vanadium oxides have been prepared by the new solution processing in an aqueous hydrogen peroxide solution with lithium and vanadium alkoxides, LiO-n-C₃H₇ and VO(O-i-C₃H₇)₃, at low temperature, compared with conventional high temperature solid state reaction. Oxides having a layered structure isomorphic to that of γ-phase Li_xV₂O₅ were obtained. This “γ-like phase” oxide can be obtained at the nominal Li/V ratio of 1.5 almost as a single phase. However, formation of ω phase cannot be confirmed. The γ-like phase oxide contained water and organic compounds, and the water content n in Li_xV₂O₅·nH₂O was found to be about 2.4 for the γ-like phase oxide. Further as the result of the atomic absorption spectrometric method, the lithium content x in Li_xV₂O₅·nH₂O was estimated to be 2.2, and water molecules presumably exist in the interlayer space.Water content of the γ-like phase oxides, affects charge and discharge behaviours markedly. The lithium extraction-insertion capacity of the γ-like phase oxides were smaller, but the oxides had higher average potential compared with those of γ-phase oxide. As water content of γ-like phase oxides decreased, the lithium extraction-insertion capacity increased. Moreover, it should be noted that the average potential of γ-like phase oxides is at least 1 V higher than that of γ-LiV₂O₅.     

An investigation of intercalation-induced stresses generated during lithium transport through sol-gel derived LixMn2O4 film electrode using a laser beam deflection method

The stress changes Δσ generated during lithium transport through the sol-gel derived Li_xMn₂O₄ film electrodes annealed at 773 and 873 K were quantitatively determined as a function of the lithium stoichiometry x using a laser beam deflection method (LBDM). Δσ generated during a real potential step between an initial electrode potential and a final applied potential was uniquely specified by the Δσ versus x curve. The Li_xMn₂O₄ film annealed at 773 K for 24 h (low temperature (LT)-Li_xMn₂O₄) showed larger capacity than the Li_xMn₂O₄ film annealed at 873 K for 6 h (high temperature (HT)-Li_xMn₂O₄) and this result is ascribed to the fact that the smaller the grain size is, the more increases the electrochemically active area of the film electrode. From the analysis of the normalised Δσ transient measured simultaneously along with the cyclic voltammogram in the potential range of 2.5-3.4 VLi/Li⁺, it is found that normalised Δσ generated in the LT-Li_xMn₂O₄ was smaller than that in the HT-Li_xMn₂O₄ during the lithium intercalation/de-intercalation around 3.0 VLi/Li⁺ region. This result gives an experimental evidence for the fact that the Jahn-Teller distortion is suppressed by the increase in the average oxidation state of manganese with decreasing in annealing temperature.     

Effects of annealing temperature on the photocatalytic activity of N-doped TiO2 thin films

The effects of annealing temperature on the photocatalytic activity of nitrogen-doped (N-doped) titanium oxide (TiO₂) thin films deposited on soda-lime-silica slide glass by radio frequency (RF) magnetron sputtering have been studied. Glancing incident X-ray diffraction (GIAXRD), Raman spectrum, scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV-vis spectra were utilized to characterize the N-doped TiO₂ thin films with and without annealing treatment. GIAXRD and Raman results show as-deposited N-doped TiO₂ thin films to be nearly amorphous and that the rutile and anatase phases coexisted when the N-doped TiO₂ thin films were annealed at 623 and 823 K for 1 h, respectively. SEM microstructure shows uniformly close packed and nearly round particles with a size of about 10 nm which are on the slide glass surface for TiO₂ thin films annealed at 623 K for 1 h. AFM image shows the lowest surface roughness for the N-doped TiO₂ thin films annealed at 623 K for 1 h. The N-doped TiO₂ thin films annealed at 623 K for 1 h exhibit the best photocatalytic activity, with a rate constant (k_a) of about 0.0034 h⁻¹.     

NiO-based composite electrode with RuO2 for electrochemical capacitors

NiO/RuO₂ composite materials were prepared for use in electrochemical capacitors (ECs) by co-precipitation method followed by heat treatment. X-ray diffraction (XRD) spectra indicated that no new structural materials were formed and ruthenium oxide particles were coated by NiO particles. RuO₂ partly introduced into NiO-based electrode had improved its electrochemical performance and capacitive properties by using electrochemical measurements. A maximum specific capacitance of 210 F/g was obtained for NiO-based composite electrode with 10 wt.% RuO₂ in the voltage range from −0.4 to 0.5 V in 1 mol/l KOH solution. By comparison of effect of modified modes on the specific capacitance, chemically modified composite electrodes had more stable cycling properties than those of physically modified electrodes. After 200 cycles, specific capacitance of NiO-based chemical composite electrode with 5 wt.% RuO₂ kept 95% above, while that of physical electrode was only 79% of initial specific capacitance.     

Preparation and electrochemical capacitance of RuO2/TiO2 nanotubes composites

In this paper, RuO₂/TiO₂ nanotubes composites were synthesized by loading various amounts of RuO₂ on TiO₂ nanotubes. The symmetric supercapacitors based on these nanocomposites were fabricated by using gel polymer PVA-H₃PO₄-H₂O as electrolyte. The electrochemical capacitance performance of the nanocomposites in these supercapacitors was investigated by current-potential responses, galvanostatic charge-discharge tests and electrochemical impedance spectroscopy. The results show that the three dimensional nanotube network of TiO₂ offers a solid support structure for active materials RuO₂, allows the active material to be readily accessible (available) for electrochemical reactions, and improves the efficiency of the active materials. A maximum specific capacitance of 1263 F/g was obtained for the RuO₂ which was loading on TiO₂ nanotubes.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

Stable Ti/RuO2-Sb2O5-SnO2 electrodes for O2 evolution

RuO₂-based electrodes are generally known to be unstable for O₂ evolution. In this paper, a stable type of RuO₂-based electrode, Ti/RuO₂-Sb₂O₅-SnO₂, is demonstrated for O₂ evolution. In the ternary oxide coating, RuO₂ serves as the catalyst, SnO₂ as the dispersing agent, and Sb₂O₅ as the dopant. The accelerated life test showed that the Ti/RuO₂-Sb₂O₅-SnO₂ electrode containing 12.2 molar percent of RuO₂ nominally in the coating had a service life of 307 h in 3 M H₂SO₄ solution under a current density of 0.5 A cm⁻² at 25 °C, which is more than 15 times longer than other types of RuO₂-based electrodes. Instrumental analysis indicated that RuO₂-Sb₂O₅-SnO₂ was a solid solution with a compact structure, which contributed to the stable nature of the electrode.