Evaluation and origins of the difference between double-layer capacitance behaviour at Au-metal and oxidized Au surfaces

In studies of processes at oxidized compared with unoxidized electrode surfaces by transient methods corrections for double-layer charging are usually required and have often been made by extrapolation of double-layer capacitance (C_dl) data for the metallic surface, e.g. at Au or Pt, into the potential region of oxide-film formation. Voltammetry and impedance spectroscopy provide direct information on C_dl values determined at unoxidized, i.e. metallic, Au surfaces compared with those of anodic oxide films generated potentiostatically to various extents that are stable in time, and characterized by reductive linear-sweep voltammetry. C_dl is derived from constant-phase element (CPE) values and the CPE parameter, ?, which is near unity for most conditions. At oxidized Au surfaces C_dl depends on potential for various extents of oxide formation; it increases from 15 (±1) μF cm⁻² at 1.75 V (RHE) to 25 (±1) μF cm⁻² at 1.45 V (RHE) and is independent of added Cl⁻ or Br⁻ for concentrations 0-10⁻³ M of both anions, while, at unoxidized Au electrodes in the absence of halide anions, C_dl has a maximum value of 60 (±2) μF cm⁻² at 0.80 V (RHE) and is now dependent on concentration of added Cl⁻ or Br⁻ ion. These major differences of C_dl for the oxidized and unoxidized Au surfaces indicate that double-layer charging corrections cannot be made simply by extrapolation of C_dl data for unoxidized Au metal surfaces into the potential region for oxide formation.     

Electrochemical oxidation of hydrogen peroxide at a bromine adatom-modified gold electrode in alkaline media

Bromine (Br)-adatom (Br_(ads)) was in situ fabricated onto polycrystalline gold (Au (poly)) electrode in Br⁻-containing alkaline media. The surface coverage of Br_(ads) (Γ_Br) varied only in the submonolayer coverage within the investigated potential window under potentiodynamic condition because of the coadsorption of hydroxyl ion (OH⁻) in alkaline media. The in situ fabricated Br_(ads)-submonolayer-coated Au (poly) electrode was successfully used for the electrochemical oxidation of hydrogen peroxide (H₂O₂). About five times higher oxidation current was achieved at the modified electrode as compared with the bare electrode. The enhancement of the electrode activity towards the electrochemical oxidation of H₂O₂ was explained based on the enhanced electrostatic attraction between the anionic HO₂⁻ molecules and Br_(ads)-adlayer-induced positively polarized Au (poly) electrode surface.     

Electrocatalytic oxidation of ascorbic acid by [Fe(CN)6] redox couple electrostatically trapped in cationic N,N-dimethylaniline polymer film electropolymerized on diamond electrode

Multinegatively charged metal complex, hexacyanoferrate ([Fe(CN)₆]⁴⁻), was electrostatically trapped in the cationic polymer film of N,N-dimethylaniline (PDMA) which was electrochemically deposited on the boron-doped diamond (BDD) electrode by controlled-potential electro-oxidation of the monomer. This ferrocyanide-trapped PDMA film was used to catalyze the oxidation of ascorbic acid (AA). Increase in the oxidation current response with a negative shift of the anodic peak potential was observed at the cationic PDMA film-coated BDD (PDMA|BDD) electrode, compared with that at the bare BDD electrode. A more drastic enhancement in the oxidation peak current as well as more negative shift of oxidation potential was found at the ferrocyanide-trapped PDMA film-coated BDD ([Fe(CN)₆]^3−/4−|PDMA|BDD) electrode. This [Fe(CN)₆]^3−/4−|PDMA|BDD electrode can be used as an amperometric sensor of AA. Ferrocyanide, electrostatically trapped in the polymer film shows more electrocatalytic activity than that coordinatively attached to the polymer film or dissolved in the solution phase. The electrocatalytic current depends on the surface coverage of ferricyanide, Γ_Fe, within the polymer film. Diffusion coefficient (D) of AA in the solution was estimated by rotating disk electrode voltammetry: D = (5.8 ± 0.3) × 10⁻⁶ cm² s⁻¹. The second-order rate constant for the catalytic oxidation of AA by ferricyanide was also estimated to be 9.0 × 10⁴ M⁻¹ s⁻¹. In the hydrodynamic amperometry using the [Fe(CN)₆]^3−/4−|PDMA|BDD electrode, a successive addition of 1 μM AA caused the successive increase in current response with equal amplitude and the sensitivity was calculated as 0.233 μA cm⁻² μM⁻¹.     

Fabrication of carbon paste electrode containing [PFeW11O39] polyoxoanion supported on modified amorphous silica gel and its electrocatalytic activity for H2O2 reduction

[PFeW₁₁O₃₉]⁴⁻ (PFeW₁₁) supported on the surface of 3-aminopropyl(triethoxy)silane modified silica gel was synthesized and used as a bulk modifier to fabricate a renewable three-dimensional chemically modified electrode. The electrochemical behavior of the modified electrode was investigated. Cyclic voltammetry studies showed that the PFeW₁₁ on the electrode surface sustained the same electrochemical properties as that of the PFeW₁₁ in solution. The preparation of chemically modified electrode is simple and quiet reproducible using inexpensive material. The modified electrode had high electrocatalytic activity toward H₂O₂ reduction and it was successfully applied as an electrochemical detector to monitor H₂O₂ in flow injection analysis (FIA). The electrocatalytic peak current was found to be linear with the H₂O₂ concentration in the range 10-200 μmol L⁻¹ with a correlation coefficient of 0.998 and a detection limit (3σ) of 7.4 μmol L⁻¹ H₂O₂. The electrode has the remarkable advantage of surface renewal owing to bulk modification, as well as simple preparation, good mechanical and chemical stability and reproducibility.     

Poly-phenothiazine derivative-modified glassy carbon electrode for NADH electrocatalytic oxidation

Electropolymerization of a new phenothiazine derivative (bis-phenothiazin-3-yl methane; BPhM) on glassy carbon (GC) electrode generates a conducting film of poly-BPhM, in stable contact with the electrode surface. The heterogeneous electron-transfer process corresponding to the modified electrode is characterized by a high rate constant (50.4 s⁻¹, pH 7). The GC/poly-BPhM electrode shows excellent electrocatalytic activity toward NADH oxidation. The rate constant for catalytic NADH oxidation, estimated from rotating disk electrode (RDE) measurements and extrapolated to zero concentration of NADH, was found to be 9.4 × 10⁴ M⁻¹ s⁻¹ (pH 7). The amperometric detection of NADH, at +200 mV vs. SCE, is described by the following electroanalytical parameters: a sensitivity of 1.82 mA M⁻¹, a detection limit of 2 μM and a linear domain up to 0.1 mM NADH.     

Hydrophilic carbon nanoparticle-laccase thin film electrode for mediatorless dioxygen reduction: SECM activity mapping and application in zinc-dioxygen battery

Laccase from Cerrena unicolor was adsorbed on hydrophilic carbon nanoparticles (diameter = ca. 7.8 nm) modified with phenyl sulfonate groups and immobilized on an ITO electrode surface in a sol-gel processed silicate film. As shown by scanning electron and atomic force microscopies, the nanoparticles are evenly distributed on the electrode surface forming small aggregates of tens of nanometers in size. The mediator-free electrode exhibits significant and pH-dependent electrocatalytic activity towards dioxygen reduction. The maximum catalytic current density (95 μA cm⁻²) is obtained at pH 4.8 corresponding to maximum activity of the enzyme. Under these conditions dioxygen electroreduction commences at 0.575 V vs. Ag|AgCl_sat, a value close to the formal potential of the T1 redox centre of the laccase. The scanning electrochemical microscopy images obtained in redox competition mode exploiting mediatorless electrocatalysis show that the laccase is evenly distributed in the composite film. The obtained electrode was applied as biocathode in a zinc-dioxygen battery operating in 0.1 M McIlvaine buffer (pH 4.8). It provides 1.48 V at open circuit and a maximum power density 17.4 μW cm⁻² at 0.7 V.     

Strategy for the syntheses of isolated fine silver nanoparticles and polypyrrole/silver nanocomposites on gold substrates

In this work, isolated fine silver nanoparticles and polypyrrole/silver nanocomposites with diameters of about 10 nm on gold substrates were first prepared by electrochemical methods. First, an Ag substrate was cycled in a deoxygenated aqueous solution containing 0.1 M HCl from −0.30 to +0.30 V versus Ag/AgCl at 5 mV/s with 30 scans. Subsequently the Ag working electrode was immediately replaced by an Au electrode and a cathodic overpotential of 0.2 V was applied under controlled sonication to synthesize Ag nanoparticles on the Au electrode. Then pyrrole monomers were encouragingly found to be polymerized on the deposited Ag nanoparticles. This polymerization is distinguishable from the known chemical or electrochemical one, due to the electrochemical activity of unreduced species of Ag_n⁺ clusters inside the nanoparticles. Also, this polymerization may be ascribed to the oxidizing agent of AuCl₄⁻, which is present on the Au electrode.     

Seed-mediated growth of platinum nanoparticles on carbon nanotubes for the fabrication of electrochemical biosensors

Platinum nanoparticles (PtNPs) were prepared by seed-mediated growth method with Au nanoparticles (AuNPs) playing the role of seeds. Carbon nanotubes (CNTs) and AuNPs were first dropped onto the surface of glassy carbon (GC) electrode, and then the electrode was immersed into growth solution which contains H₂PtCl₆ and ascorbic acid. PtNPs were successfully grown onto the CNT surface due to the chemical reduction of Pt(IV). The electrode modified with AuNP_seed/PtNP/CNT film displayed excellent electrochemical response to H₂O₂ at 0.45 V versus saturated calomel electrode (SCE) with sensitivity much larger than that of PtNP/CNT and AuNP_seed/PtNP modified electrodes. Glucose oxidase was selected as a model enzyme and electrodeposited onto the AuNP_seed/PtNP/CNT modified electrode in the presence of a detergent. The resulting biosensor enabled selective determination of glucose with high sensitivity of 4.49 μA mM⁻¹, quick response time about 2 s, low-detection limit of 0.5 μM and wide linear range from 1 μM to 4 mM with a correlation coefficient 0.9998. Thus, the modified electrode proved to be a nice electrochemical biosensing platform for the fabrication of oxidase-based biosensors.     

Electrocatalytic activity of 2,3,5,6-tetrachloro-1,4-benzoquinone/multi-walled carbon nanotubes immobilized on edge plane pyrolytic graphite electrode for NADH oxidation

This work reports the electrocatalytic activity of 2,3,5,6-tetrachloro-1,4-benzoquinone (TCBQ)/multi-walled carbon nanotubes (MWCNT) immobilized on an edge plane pyrolytic graphite electrode for nicotinamide adenine dinucleotide (NADH) oxidation. Scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS) were used to confirms the presence of chloro after the nanotube modification with 2,3,5,6-tetrachloro-1,4-benzoquinone. The surface charge transfer constant, k_s, and the charge transfer coefficient for the modified electrode, α, were estimated as 98.5 (±0.6) s⁻¹ and 0.5, respectively. With this modified electrode the oxidation potential of the NADH was shifted about 300 mV toward a less positive value, presenting a peak current much higher than those measured on an unmodified edge plane pyrolytic graphite electrode (EPPG). Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the NADH oxidation reaction involves 2 electrons and a heterogenous rate constant (k_obs) of 3.1 × 10⁵ mol⁻¹ l s⁻¹. The detection limit, repeatability, long-term stability, time of response and linear response range were also investigated.     

Evaluation of the pseudocapacitance in RuO2 with a RuO2/GC thin film electrode

The pseudocapacitance of nanocrystalline RuO₂ with BET surface area of 42 m² g⁻¹ was evaluated using a RuO₂ modified Glassy Carbon (RuO₂/GC) thin film electrode. The charge storage behavior of the RuO₂/GC thin film electrode was studied from fast to slow scan cyclic voltammetry between various potential windows. The utilization of the thin film electrode method for nanocrystalline RuO₂ with known specific surface area allowed a semi-quantitative understanding of the electric double-layer capacitance (C_dl), adsorption related charge (C_ad), and the irreversible redox related charge (C_irr) per unit mass and surface area of RuO₂. Comparison of the cyclic voltammograms between different voltage windows revealed that the contribution from C_irr is especially dominant below 0.4 V (versus RHE) at slow scan rates.     

Electrochemical determination of bromide at a multiwall carbon nanotubes-chitosan modified electrode

A multiwall carbon nanotubes (MWNTs)-chitosan modified glassy carbon electrode (GCE) exhibits attractive ability for highly sensitive cathodic stripping voltammetric measurements of bromide (Br⁻). In pH 1.8 H₂SO₄ solution, a substantial increase in the stripping peak current of Br⁻ (compared to bare GCE and chitosan modified GCE) is observed using MWNTs-chitosan modified electrode. Operational parameters were optimized and the electrochemical behaviors of Br⁻ were studied by different electrochemical methods. The kinetics parameters were measured, the number of electron transfer (n) was 1 and the transfer coefficient (α) is 0.17. A wide linear calibration range (3.6 × 10⁻⁷-1.4 × 10⁻⁵ g mL⁻¹) was achieved, with a detection limit of 9.6 × 10⁻⁸ g mL⁻¹. The mechanism of electrode reaction was fully discussed.     

Development of a sensor based on tetracyanoethylenide (LiTCNE)/poly-l-lysine (PLL) for dopamine determination

The catalytic oxidation of dopamine (DA) at a LiTCNE (lithium tetracyanoethylenide) film modified electrode is studied by electrochemical approaches. The immobilization of LiTCNE was performed by a polymer (poly-l-lysine) to prepare this modified electrode and its application for dopamine (DA) determination is described in detail. The modified electrode showed a high activity for the electrooxidation of dopamine (DA) at E_p = 0.20 V versus SCE. The modified electrode presented a wide linear response range for DA from 0.01 up to 10 μmol l⁻¹ by differential pulse voltammetry (DPV) with a detection limit of 0.5 nmol l⁻¹. The repeatability of the proposed sensor evaluated in term of relative standard deviation was 3.2% for n = 10. The sensor was applied for the determination of dopamine in pharmaceutical formulations and the average recovery for these samples was 101.9 (±0.1)%.     

Simultaneous determination of paracetamol and ascorbic acid using tetraoctylammonium bromide capped gold nanoparticles immobilized on 1,6-hexanedithiol modified Au electrode

Tetraoctylammonium bromide stabilized gold nanoparticles (TOAB-AuNPs) attached to 1,6-hexanedithiol (HDT) modified Au electrode was used for the simultaneous determination of paracetamol (PA) and ascorbic acid (AA) at physiological pH. The attachment of TOAB-AuNPs on HDT modified Au surface was confirmed by attenuated total reflectance (ATR)-FT-IR spectroscopy and atomic force microscope (AFM). The ATR-FT-IR spectrum of TOAB-AuNPs attached to the HDT monolayer showed a characteristic stretching modes corresponding to -CH₂ and -CH₃ of TOAB, confirming the immobilization of AuNPs with surface-protecting TOAB ions on the surface of the AuNPs after being attached to HDT modified Au electrode. AFM image showed that the immobilized AuNPs were spherical in shape and densely packed to a film of ca. 7 nm thickness. Interestingly, TOAB-AuNPs modified electrode shifted the oxidation potential of PA towards less positive potential by 70 mV and enhanced its oxidation current twice when compared to bare Au electrode. In addition, the AuNPs modified electrode separated the oxidation potentials of AA and PA by 210 mV, whereas bare Au electrode failed to resolve them. The amperometry current of PA was increased linearly from 1.50 × 10⁻⁷ to 1.34 × 10⁻⁵ M with a correlation coefficient of 0.9981 and the lowest detection limit was found to be 2.6 nM (S/N = 3). The present method was successfully used to determine the concentration of PA in human blood plasma and commercial drugs.     

Fabrication of Fc-SWNTs modified glassy carbon electrode for selective and sensitive determination of dopamine in the presence of AA and UA

The electrochemistry of dopamine (DA) was investigated by cyclic voltammetry (CV) and differential pulse voltammograms (DPV) at a glassy carbon electrode modified by the hybridization adducts of Fc-SWNTs. The electro-oxidation of DA could be catalyzed by Fc/Fc⁺ couple as a mediator and had a higher electrochemical response due to the unique carbon surface of carbon nanotubes. The anodic peaks of DA, ascorbic acid (AA) and uric acid (UA) in their mixture can be well separated by the prepared electrode. Under optimum conditions linear calibration graphs were obtained over the DA concentration range 5.0 × 10⁻⁶ to 3.0 × 10⁻⁵ M with a correlation coefficient of 0.9998 and a detection limit of 5.0 × 10⁻⁸ M based on the equation C_m = 3s_b1/m. The modified electrode has been successfully applied for the assay of DA in human blood serum. This work provides a simple and easy approach to selectively detect DA in the presence of AA and UA.     

Glassy carbon electrode modified with Nafion-Au colloids for clenbuterol electroanalysis

Stable Nafion-Au colloids were immobilized on a glassy carbon electrode (GCE) for detection of β-agonist clenbuterol by electroanalysis. The Au colloids were prepared by a one-step electrodeposition onto GCE, with obvious electrocatalytic activity present. The negatively charged Nafion film was an efficient barrier to negatively charged interfering compounds, resulting in accumulation of positively charged clenbuterol at the Nafion film. The electrochemical characters of the electrode during various modified steps in a redox probe system of K₄[Fe(CN)₆]/K₃[Fe(CN)₆] were confirmed by cyclic voltammetry (CV) and AC-impedance. In Britton-Robinson (B-R) buffer solution (pH = 2.0) and the potential range of −0.2 to 1.2 V, the Nafion-Au colloid modified electrode, compared to a bare GCE, exhibits obvious electrocatalytic activity towards the redox of clenbuterol by greatly enhancing the peak current with a linear calibration curve from 8.0 × 10⁻⁷ to 1.0 × 10⁻⁵ mol/L and a detection limit of (1.0 × 10⁻⁷ mol/L) (R = 0.996). The modified electrode shows high sensitivity, selectivity and reproducibility. The recovery for detecting clenbuterol (∼10⁻⁶ mol/L) in human serum is up to 98.19%.     

Preparation and electrocatalytic oxidation properties of a nickel pentacyanonitrosylferrate modified carbon composite electrode by two-step sol-gel technique: improvement of the catalytic activity

The sol-gel technique was used to construct nickel pentacyanonitrosylferrate (NiPCNF) modified composite ceramic carbon electrodes (CCEs). This involves two steps: forming a CCE containing Ni powder and then immersing the electrode into a sodium pentacyanonitrosyl-ferrate solution (electroless deposition). The cyclic voltammograms of the resulting surface modified CCE under optimum conditions show a well-defined redox couple due to the [Ni^IIFe^III/II(CN)₅NO]^0/−1 system. The electrochemical properties and stability of the modified electrode were investigated by cyclic voltammetry. The apparent electron transfer rate constant (k_s) and transfer coefficient (α) were determined by cyclic voltammetry being about 1.1 s⁻¹ and 0.55, respectively. Sulfite has been chosen as a model to elucidate the electrocatalytic ability of NiPCNF-modified CCE prepared by one- or two-step sol-gel technique. The modified electrode showed excellent electrocatalytic activity toward the SO₃²⁻ electro oxidation in pH range 3-9 in comparison with CCE modified by homogeneous mixture of graphite powder, Ni(NO₃)₂ and Na₂[Fe(CN)₅NO] (one-step sol-gel technique). Sulfite was determined amperometrically at the surface of this modified electrode in pH 7. Under the optimized conditions the calibration curve is linear in the concentration range 2 μM to 2.0 mM. The detection limit (signal-to-noise is 3) and sensitivity are 0.5 μM and 13.5 nA/μM. The modified carbon ceramic electrode containing nickel pentacyanonitrosylferrate shows good repeatability, short response time, t (90%) <2 s, long-term stability (3 months), and it is renewed by simple mechanical polishing and its immersing in Na₂[Fe(CN)₅NO] solution. The advantages of the SO₃²⁻ amperometrically detector based on the nickel pentacyanonitrosylferrate-doped CCE is high sensitivity, inherent stability at wide pH range, excellent catalytic activity and less expense and simplicity of preparation. This sensor can be used as amperometric detector in chromatographic instruments.     

Electrochemical nitrite nanosensor developed with amine- and sulphate-functionalised polystyrene latex beads self-assembled on polyaniline

Aniline doped with polyvinyl sulphonate (PV-SO₃⁻) was electropolymerised on screen printed carbon (SPCE) and glassy carbon (GCE) electrodes. Then nano-structured polystyrene (PS_NP) latex beads functionalised with amine (PS_NP-NH₂) and sulphate (PS_NP-OSO₃⁻) were self-assembled on the modified SPCE and GCE. The resultant polyaniline nanocomposites (PANI|PS_NP-NH₂ or PANI|PS_NP-OSO₃⁻) were characterised by cyclic voltammetry (CV), UV-vis spectroscopy and scanning electron microscopy (SEM). Brown-Anson analysis of the multi-scan rate CV responses of the various PANI films gave surface concentrations of the order of 10⁻⁸ mol cm⁻². UV-vis spectra of the PANI films dissolved in dimethyl sulphoxide showed typical strong absorbance maxima at 480 and 740 nm associated with benzenoid π-π* transition and quinoid excitons of polyaniline, respectively. The SEM images of the PANI nanocomposite films showed cauliflower-like structures that are <100 nm in diameter. When applied as electrochemical nitrite sensor, sensitivity values of 60, 40 and 30 μA/mM were obtained for electrode systems containing PANI|PS_NP-NH₂, PANI and PANI|PS_NP-SO₃⁻, respectively. The corresponding limits of detection of the sensors were 7.4, 9.2 and 38.2 μM NO₂⁻.     

Adsorption of asparagine on the gold electrode and air/solution interface

The adsorption of asparagine (Asn) on a gold electrode from 0.1 M LiClO₄ aqueous solutions was investigated. The experimental data obtained from ac impedance measurements were analyzed to determine the dependence of adsorption parameters, i.e. the standard Gibbs energy of adsorption (ΔG⁰), maximal value of surface excess concentration (Γ_max) of Asn and parameter of interactions in the adsorbed layer (A) on the electrode potential. The relatively large value of Gibbs energy of adsorption (∼ −47 kJ mol⁻¹) gives the evidence of a very strong adsorption of Asn at the polycrystalline Au electrode. The comparison of the adsorption behavior of Asn at the air/solution and the Au/solution interfaces points out to the significant electronic interactions of adsorbate molecules with the Au electrode, since the adsorption of Asn on a free surface (from the same solutions) is very week. The analysis of the electrochemical data as well as the infrared reflection absorption spectroscopy (IRAS) results reveal that Asn molecules are anchored to the Au surface through oxygen atoms of the carboxylate group COO⁻ and through the amide carbonyl group.     

Electrocatalysis of asulam on cobalt phthalocyanine modified multi-walled carbon nanotubes immobilized on a basal plane pyrolytic graphite electrode

This work describes the electrochemical properties of cobalt tetra-aminophthalocyanine (CoTAPc) complex electropolymerized at the surface of multi-walled carbon nanotube (MWCNT) abrasively immobilized onto a basal plane pyrolytic graphite electrode (BPPGE). The constructed electrode displayed excellent electrocatalytic behaviour towards the oxidation of the herbicide, asulam, as evidenced by the enhancement of the oxidation peak current (∼6 times) and the shift in the oxidation potential to lower values (by ∼120 mV) in comparison with the bare BPPGE. The chronoamperometric detection of asulam which was carried out in 0.10 M phosphate buffer (pH 7.0) at a fixed potential of 0.65 V (versus Ag|AgCl) yielded excellent analytical parameters; a linear concentration range of 4.5-20 μM, a sensitivity of 241 × 10⁻³ μA/μM, a detection limit of 1.15 μM asulam (using the Y_B + 3σ criterion) and a response time of ∼2 s.     

Efficient electrochemical decomposition of perfluorocarboxylic acids by the use of a boron-doped diamond electrode

The electrochemical decomposition of environmentally persistent perfluorooctanoic acid (PFOA) was achieved by the use of a boron-doped diamond (BDD) electrode. The PFOA decomposition follows pseudo-first-order kinetics, with an observed rate constant (k₁) of 2.4 × 10^− 2 dm³ h^− 1. Under the present reaction conditions, k₁ increased with increasing current density and saturated at values over 0.60 mA cm^− 2. Therefore, the rate-limiting step for the electrochemical decomposition of PFOA was the direct electrochemical oxidation at lower current densities. In the proposed decomposition pathway, direct electrochemical oxidation cleaves the C-C bond between the C₇F₁₅ and COOH in PFOA and generates a C₇F₁₅ radical and CO₂. The C₇F₁₅ radical forms the thermally unstable alcohol C₇F₁₅OH, which undergoes F⁻ elimination to form C₆F₁₃COF. This acid fluoride undergoes hydrolysis to yield another F⁻ and the perfluorocarboxylic acid with one less CF₂ unit, C₆F₁₃COOH. By repeating these processes, finally, PFOA was able to be totally mineralized to CO₂ and F⁻. Moreover, whereas the BDD surface was easily fluorinated by the electrochemical reaction with the PFOA solution, medium pressure ultraviolet (MPUV) lamp irradiation in water was able to easily remove fluorine from the fluorinated BDD surface.