Electrochemical synthesis of self-organized TiO2 nanotubular structures using an ionic liquid (BMIM-BF4)

We show that an ionic liquid consisting of imidazolium salt with a BF₄ counter ion (BMIM-BF₄) can directly be used to grow well-defined layers of self-organized TiO₂ nanotubes. For this a Ti metal substrate is anodized in this electrolyte for potential range between 3 V_Ag/AgCl and 10 V_Ag/AgCl without addition of free fluoride species (fluorides are used in all previous tube growth procedures). Key factors that influence the morphology and geometry of the resulting nanotubular layer are the anodic potential, the anodization time and particularly the water content in the ionic liquid. The resulting nanotubes layers have thickness in the range of approximately 300-650 nm; with individual tubes that have diameters between 27 nm and 43 nm.     

Escherichia coli inactivation by N, S co-doped commercial TiO2 powders under UV and visible light

Commercial anatase TiO₂ powders (Tayca TKP101, TKP102) were ground with thiourea and annealed at 400 and 500 °C. Diffuse reflectance spectra (DRS) showed that the doping with thiourea shifted the TiO₂ absorption towards the visible region. The absorption was observed to increase with increasing annealing temperature. Using the Kubelka–Munk relations, it was possible to determine the band-gap of the doped TiO₂. Doped Tayca TiO₂ TKP101 showed a band-gap of 2.12 and 2.24 eV calcined at 400 and 500 °C, respectively. Doped Tayca TiO₂ TKP102 calcined at 400 and 500 °C showed in both cases a band-gap of 2.85 eV. X-ray photoelectron spectroscopy (XPS) revealed that these doped TiO₂, TKP101 annealed at 400 °C and TKP102 annealed at 400 and 500 °C present interstitial N-doping while doped TKP101 annealed at 500 °C showed a peak characteristic of substitutional N-doping. S-doped materials calcined at 500 °C presented only anionic S-doping. Nitrogen adsorption studies (BET) showed a loss of specific surface area (SSA) in annealed TiO₂ samples. N- and S co-doped materials showed suitable photocatalytic activity under UV illumination towards Escherichia coli inactivation and also under visible light irradiation (400–500 nm). Applying different annealing temperatures led to a variety of structures for N and S incorporated in the crystalline network. TiO₂ upon annealing showed a varying degree of hydroxylation and particles sizes. This seems to affect the trapping and transfer of the charge carriers generated under light and the semiconductor performance.     

Formation of TiO2 nano fibers on a micro-channeled Al2O3-ZrO2/TiO2 porous composite membrane for photocatalytic filtration

In this study, needle-shape TiO₂ fibers were successfully fabricated inside a micro-channeled Al₂O₃-ZrO₂ composite porous membrane system using sol-gel method. The micro-channeled Al₂O₃-ZrO₂ composite was fabricated using the fibrous monolithic (FM) process. Pure anatase phase TiO₂ was crystallized from the as-coated amorphous phase during calcination at 510 °C. The TiO₂ fibers grew on the surface frame of the micro-channeled Al₂O₃-ZrO₂ composite membrane and fully covered the inside of the micro-channeled pores. The specific surface area of the TiO₂ coated membrane system was dramatically increased by over 100 fold compared to that of the non-coated system. The photocatalytic activity of the membrane was also assessed and was shown to very effectively convert organic materials. Thus, this novel membrane holds promise for use as an advanced filtration system.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

TiO2 nanotubes and CNT–TiO2 hybrid materials for the photocatalytic oxidation of propene at low concentration

In this work, we investigated titanium dioxide (TiO₂) nanotubes and CNT–TiO₂ hybrid materials for the photocatalytic oxidation (PCO) of propene at low concentration (100 ppmv) in gaseous phase. The materials were prepared via sol–gel method using sacrificial multi-walled carbon nanotubes (CNT) as templates and subsequent heat treatments to obtain the desired crystalline phase (anatase, rutile or a mixture of both) and eventually to remove the carbon template. We also studied rutile nanotubes for the first time and demonstrate that the activity strongly depends on the crystalline composition, following rutile < anatase < anatase/rutile mixture. The enhanced activity of the anatase–rutile mixture is attributed to the decrease in the electron–hole pair recombination due to the multiphasic nature of the particles. The key result of this work is the exceptional performance of the CNT–TiO₂ hybrid, which yielded the highest observed photocatalytic activity. The improved performance is attributed to synergistic effects due to the hybrid nature of the material, resulting in small anatase crystalline sizes (CNT act as heat sinks) and a reduced electron–hole pair recombination rate (CNTs act as electron traps). These results demonstrate the great potential of hybrid materials and stimulate further research on CNT-inorganic hybrid materials in photocatalysis and related areas.     

The photocatalytic efficiency of the metal doped TiO2 with ceramic foam as catalyst carriers

The metal doped TiO₂ was prepared with Fe(III), Co(II), Ni(II), Cu(II), Ag(I), La (III), Nd(III), Ho(III), and Y(III) as doped catalysts. These catalysts were carried by ceramic foams to enhance their photocatalytic efficiency, which was later studied with methylene blue (MB) and Escherichia coli (E. coli) as targets. The results suggested that the photocatalytic activities of TiO₂ were enhanced when ceramic foams were used as catalyst carriers and that the photocatalytic efficiency could also be significantly increased by the dopants, especially by Ag(I) and rare earth. In the bactericidal activity testing, the inhibitory effect of TiO₂ on E. coli was enhanced significantly when ceramic foams were used as carriers. Ag(I) doped TiO₂ showed the greatest inhibition on E. coli. As to the E. coli cells treated by Ag(I) doped TiO₂, the observation with a Scanning Electronic Microscope (SEM) suggested that the cells could no longer maintain their morphology and the spheroplasts were formed after the treatment.     

Preparation and electrochemical capacitance of RuO2/TiO2 nanotubes composites

In this paper, RuO₂/TiO₂ nanotubes composites were synthesized by loading various amounts of RuO₂ on TiO₂ nanotubes. The symmetric supercapacitors based on these nanocomposites were fabricated by using gel polymer PVA-H₃PO₄-H₂O as electrolyte. The electrochemical capacitance performance of the nanocomposites in these supercapacitors was investigated by current-potential responses, galvanostatic charge-discharge tests and electrochemical impedance spectroscopy. The results show that the three dimensional nanotube network of TiO₂ offers a solid support structure for active materials RuO₂, allows the active material to be readily accessible (available) for electrochemical reactions, and improves the efficiency of the active materials. A maximum specific capacitance of 1263 F/g was obtained for the RuO₂ which was loading on TiO₂ nanotubes.     

Photocatalytic activity of transparent porous glass supported TiO2

A porous glass tube with a composition of 96SiO₂·4B₂O₃ (wt%) supported TiO₂ shows high photooxidation activity due to its transparency and large surface area. The surface area of the porous glass tube supported TiO₂ is 10,000 times larger than that of conventional materials. TiO₂ crystals supported are anatase type. Transparency of the porous glass tube is very important. Herein, sol–gel and chemical vapor deposition (CVD) processes were employed as TiO₂ supporting processes. CVD process is more effective. For instance, an aqueous methylene blue solution with 1 ppm concentration almost thoroughly decomposes at a contact time of 300 s using porous glass tube supported TiO₂ prepared by CVD process under irradiating with 10 W low-pressure mercury lamp, on the other hand, opaque porous alumina tube supported TiO₂ was only 25%. The smaller the pore size of the porous glass tube, the larger the transparency and the permeation resistance through porous glass tube. Hence, porous glass tube with ca. 40 nm pore diameter is suitable from the standpoint of a practical use.     

Preparation of porous TiO2 by a novel freeze casting

Highly porous and open interconnected pore structural TiO₂ were prepared by a novel freeze casting method. In the experiment, the well-dispersed aqueous slurries were first frozen, and then dried at a reduced vacuum. Since the sublimation of ice crystals developed in the freezing process, the green bodies with highly porous were obtained. The phase composition and the microstructure of the sintered samples were characterized by XRD, SEM, porosity and the pore size distribution was measured by mercury porosimetry. The results demonstrated that the PVA concentration in the slurries remarkably affect the microstructure of TiO₂ ceramics. The pore morphology of TiO₂ ceramics with 3 wt.% polyvinyl alcohol (PVA) addition was dendritic, and however, the pore morphology of TiO₂ ceramics with 6 wt.% PVA addition changed into columnar. The reason for the variation of the pore morphology was ascribed to the effect of the PVA gelation on the growth behavior of the ice crystals.     

Spontaneously ordered TiO2 nanostructures

Titanium dioxide thin films were deposited on quartz substrates kept at different O₂ pressures using pulsed laser deposition technique. The effects of reactive atmosphere and annealing temperature on the structural, morphological, electrical and optical properties of the films are discussed. Growth of films with morphology consisting of spontaneously ordered nanostructures is reported. The films growth under an oxygen partial pressure of 3 × 10⁻⁴ Pa consist in nanoislands with voids in between them whereas the film growth under an oxygen partial pressure of 1 × 10⁻⁴ Pa, after having being subjected to annealing at 500 °C, consists in nanosized elongated grains uniformly distributed all over the surface. The growth of nanocrystallites with the increase in annealing temperature is explained on the basis of the critical nuclei-size model.     

Preparation of photocatalytic TiO2 coatings by gel-dipping with polysaccharides

Commercial tiles are being produced in vast quantities. The main properties of tiles are well established but there is an increasing interest in producing ceramics with tailored-properties and advanced functionalities. One way of adding value to commercial tiles is to deposit a photocatalytic coating to obtain ‘smart’ tiles for environmental reasons, e.g. for the (photo) degradation of organic pollutants in air or in a liquid. Here, we show the manufacture of ‘smart’ tiles by formation of TiO₂ coatings onto commercial tiles by a colloidal processing route based on the immersion of the substrate into a homogeneous aqueous ceramic suspension and its consolidation by agar thermogelation. The effect of the processing parameters (withdrawal rate, solid loading and gelling agent content) and the grain size on the photocatalytic activity of the final coated tiles is reported and discussed. Final coatings properties depend on the viscosity of the suspension, particle size, withdrawal rate, solid loading and gelling agent content, and hence, this dependence affects the photocatalytic activity of the coatings.     

TiO2 as a sintering additive for KNbO3 ceramics

Improved densification during the conventional sintering of KNbO₃ ceramics was achieved by using small additions of TiO₂. This improved densification can be explained on the basis of high-temperature chemical reactions in the system. X-ray diffractometry and electron microscopy were used in combination with diffusion-couple experiments in order to elucidate the chemical reactions between KNbO₃ and TiO₂. TiO₂ reacts with KNbO₃ forming KNbTiO₅, and a low concentration of Ti incorporates in the KNbO₃ structure resulting in the formation of oxygen vacancies and, consequently, in an improvement in the densification. At ∼1037 °C eutectic melting between the KNbO₃ and the KNbTiO₅ further improves the densification of the KNbO₃ ceramics.     

Prevention of photocatalytic deterioration of resins using TiO2 pillared fluoromica

The TiO₂ pillared fluoromica powder was kneaded with polylactic acid resin. The composite showed high photocatalytic activity for degradation of acetaldehyde and toluene gas, especially at the range of 1–3 wt.% pillared mica powder, and this photocatalytic activity was higher than that of resins containing even higher amounts of commercial TiO₂ (P-25, Degussa). The composite test pieces of pillared mica showed smaller photocatalytic deterioration than the samples with P-25 powder in out-door weathering tests. Thus, the TiO₂ pillared clay resin composite shows excellent prevention of photocatalytic deterioration and high photocatalytic activity in comparison with P-25.     

Enhanced adsorption of two azo dyes produced by carbon modification of TiO2

The process of removal of two azo dyes (Reactive Red 198 and Direct Green 99) from water was investigated. The adsorption of azo dyes onto surfaces of pristine TiO₂, P25 and carbon-modified TiO₂ (at 120 °C for 24 h) was presented. The Freundlich model of adsorption isotherm was found for pristine TiO₂ and TiO₂-P25. Modification of TiO₂ by carbon lead to the change from the Freundlich model to the Langmuir model of adsorption isotherm. For the TiO₂-C photocatalyst the adsorption capacity was determined, which was almost two times higher for Direct Green 99 than Reactive Red 198 dyes. As a result we observed the increase of photocatalytic activity of carbon-modified TiO₂ photocatalyst.     

Enhanced visible light-induced photoelectrocatalytic degradation of phenol by carbon nanotube-doped TiO2 electrodes

We used a modified sol-gel method to prepare titanium dioxide and multi-walled carbon nanotube (CNT) composites that we subsequently deposited onto indium tin oxide (ITO) conductive glass plates. We characterized these CNT-doped TiO₂ (CNT-TiO₂) films using X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and diffuse reflectance UV-vis spectroscopy. The photoelectrocatalytic (PEC) activity of the composites was evaluated through their ability to mediate the degradation of phenol. XRD measurements indicated that the TiO₂ component existed solely in the anatase phase and that the crystallinity of the CNTs was low. XPS indicated that carbon atoms could substitute for both oxygen and titanium atoms in the TiO₂ lattice to form Ti-C and Ti-O-C structures, which were responsible for the extra photoabsorption and PEC activity under illumination with visible light, in addition to those provided by the CNTs and carbonaceous and Ti³⁺ species. An interphase interaction between TiO₂ and the CNTs elevated the photoabsorbance of the composites in the visible light region. A sample of TiO₂ doped with 10% CNTs and calcined at 400 °C exhibited the highest photocurrent and PEC efficiency. We systematically investigated the effects of several parameters of the PEC process, including the applied potential and pH, on the phenol conversion.     

Influence of TiO2 and CeO2 on the hydrogenation activity of bulk Ni2P

TiO₂- and CeO₂-promoted bulk Ni₂P catalysts were prepared by impregnation and in-situ H₂ temperature-programmed reduction method. The prepared catalysts were characterized by XRD and XPS. The hydrogenation activities of the catalysts were studied using 1.5 wt.% 1-heptene in toluene and 1.0 wt.% phenylacetylene in ethanol as the model feeds. The results indicate that bulk Ni₂P possesses low hydrogenation activity but is tunable by simply controlling the content of the additives (TiO₂ or CeO₂), suggesting that TiO₂ and CeO₂ are effective promoters to enhance the hydrogenation activity of Ni₂P.     

Novel porous TiO2 glass-ceramics with highly photocatalytic ability

A porous TiO₂ glass-ceramics with high photo-oxidative activity was successfully obtained from the SiO₂–Al₂O₃–B₂O₃–CaO–TiO₂ glass system. Rutile-type TiO₂ was observed in the crystallization temperature range of 973–1173 K. The band gap of the glass-ceramics coincided approximately with that of rutile-type TiO₂. The photocatalytic activity of this glass-ceramics was about four times larger than that of a TiO₂-coated photocatalyst fabricated by the sol–gel process. Furthermore, as this porous TiO₂ glass-ceramics contained TiO₂ in composition form, it could prevent peeling of the TiO₂ from the substrate. As well, this glass-ceramics can be easily shaped into sheets, tubes, rods, etc.     

Morphology and Microstructure of As-Synthesized Anodic TiO2 Nanotube Arrays

The as-grown structure of electrochemically synthesized titania nanotube arrays is investigated by scanning electron microscope (SEM) in combination with transmission electron microscope (TEM) as well as X-ray diffraction (XRD). The analysis reveals a preferred growth direction of the nanotubes relative to the substrate surface and the well control on the nanotube arrays morphology. The crystal structure of the anatase phase is detected and exists in the tube walls without any thermal treatment, which makes it possible to realize the application of as-formed TiO₂ nanotubes avoiding the degradation of the nanotube structures when sintering. In addition, a new growth, layered model of the anodic TiO₂ nanotubes is presented to obtain further understanding of the growth mechanism.     

Effect of TiO2 on phase evolution and microstructure of MgAl2O4 spinel in different atmospheres

The effect of TiO₂ on the formation and microstructure of magnesium aluminate spinel (MgAl₂O₄) at 1600 °C in air and reducing conditions were investigated. Under reducing conditions, stoichiometric MgAl₂O₄ spinel shifted toward alumina-rich types owing to volatilization of MgO, resulting in an increase in the porosity of fired samples. Addition of graphite to mixtures of MgO and Al₂O₃ intensified the reducing conditions and accelerated the formation of non-stoichiometric MgAl₂O₄. For TiO₂-containing samples on addition of MgAl₂O₄, magnesium aluminum titanium oxide (Mg_xAl_2(1−x)Ti_(1+x)O₅, x = 0.2 or 0.3) was detected as a minor phase. Under reducing conditions, XRD peak shifts were smaller for TiO₂-containing samples than for samples without TiO₂ owing to the formation of a solid solution of TiO₂ in MgAl₂O₄ and establishment of alumina-rich spinel, which have opposite effects on increasing the lattice parameter. In bauxite-containing samples, MgAl₂O₄ spinel, corundum, magnesium orthotitanate spinel (Mg₂TiO₄) and amorphous phases were identified. Mg₂TiO₄ spinel formed a complete solid solution with MgAl₂O₄ spinel but Mg₂TiO₄ remained as a distinct phase owing to the heterogeneous microstructure of bauxite-containing samples. Also dense microstructure established in air fired TiO₂ containing samples. The results are discussed with emphasis on the application and design of alumina-magnesia-carbon refractory materials, which are used in the steel industry.