Comparison of marginal fit and microleakage of ceramic and composite inlays: an in vitro study

The purpose of this in vitro study was to evaluate the marginal fit and microleakage of four types of ceramic or resin composite inlays. Sixty extracted human third molar teeth were randomly assigned into four groups. MOD cavities without bevels were prepared. The mesiogingival margin was cut in enamel, whereas the distogingival margin was placed below the amelocemental junction. The preparations and inlays were made according to the manufacturers' instructions. After acid-etching and treatment with a dentine bonding agent the inlays were cemented with dual curing CEREC resin composite luting material. After placement and polishing 10 teeth of each group were thermocycled 2500 times between 14 degrees C and 62 degrees C. Each tooth was bisectioned and from each part, one occlusal and three proximal sections of 75-100 microns thickness were cut and ground (EXAKT Cutting and Grinding system). The marginal discrepancy and the thickness of the luting cement were measured microscopically at each section and an average for each tooth was calculated. Considerable variation of marginal fit was seen, within inlays, and among different types of inlays. In general, the Vita Dur N inlays showed the best fit, e.g. the thickness of the luting cement for Vita Dur N was 114 microns occlusally and 119 microns mesiogingivally compared to 199 microns occlusally for CEREC and 219 microns mesiogingivally for Estilux. At enamel margins, a tendency of less microleakage was seen for ceramic inlays compared to composite inlays.     

Precision of fit: the Procera AllCeram crown

STATEMENT OF PROBLEM: Strength, color stability, and precision of fit are requirements for all-ceramic restorations. The Procera AllCeram crown system, composed of a densely sintered high-purity alumina core combined with a low fusing surface porcelain, appears to satisfy most of these requirements. However, evaluation of marginal fit has not been reported. PURPOSE: This study measured the precision of fit of the Procera AllCeram crown fabricated with Procera CAD/CAM technology for the premolar and molar teeth fit to a die. MATERIAL AND METHODS: Five ivorine maxillary first premolars and first molars were prepared for full-coverage crowns. Preparations were standardized with a convergence angle of 10 degrees, chamfer margins of 1.3 to 1.5 mm circumferentially, and occlusal reduction of 2.0 mm. AllCeram crowns were fabricated for the dies, and the fit of the crown to the die was determined by using a standardized procedure with a silicone impression material that served a dual role: (1) as a retrievable luting agent, and (2) to replicate the internal aspects of the crown. Laser videography was used to measure the gap dimension between the crowns and the dies at the marginal opening, the axial wall, the cusp tip, and the occlusal adaptation measurement locations. Mean gap dimensions and standard deviations (SDs) were calculated for marginal opening, internal adaptation, and precision of fit. RESULTS: Mean gap dimensions and standard deviations at the marginal opening for the premolar and molar crowns were 56.0 microns SD +/- 21 and 63.0 microns SD +/- 13 microns, respectively. The mean gap dimensions and SDs of the internal adaptation were 69.0 microns SD +/- 17 microns for axial wall, 48.0 microns SD +/- 12 microns for cusp tip, and 36.0 microns SD +/- 7 microns for occlusal adaptation for the premolar crowns; and 49.0 microns SD +/- 3 microns axial wall, 67.0 microns SD +/- 21 microns cusp tip, and 74.0 microns SD +/- 29 microns occlusal adaptation for molar crowns. Precision of fit and SDs for premolar and molar crowns were 52.0 microns SD +/- 19 microns and 63.0 microns SD +/- 20 microns, respectively. Mean marginal openings and precision of fit gap dimensions for the crown groups were not significantly different at the .05 level. However, gap dimensions that defined the internal adaptation at the measurement locations were different (P < or = .05). CONCLUSION: Mean gap dimensions for marginal openings, internal adaptation, and precision of fit for the crown groups were below 70 microns. These findings show that the crowns studied can be prescribed with confidence knowing that the precision of fit will consistently be less than 70 microns.     

Resin-modified glass ionomers for luting posterior ceramic restorations

OBJECTIVES: Until recently, esthetic inlay restorations in posterior teeth have been limited to cavities surrounded by enamel. Dentin adhesive systems in combination with luting composites and light-cured resin-modified glass ionomer cements offer a possibility for bonding ceramic inlays to cavities when the cervical margin is in dentin. This study was designed to compare in vitro marginal integrity of ceramic inlays bonded to dentin to restorations placed in cavities with margins located entirely in the enamel. METHODS: In the present in vitro study, the sealing abilities of a dentin bonding agent/luting composite combination (Syntac/Dual Cement, Vivadent) and resin-modified glass ionomers (Photac Fil, Photac Bond, ESPE; Dyract, De Trey Dentsply; Fuji II LC, GC Dental Industrial Corp.; and Vitremer, 3M Dental Products) used as luting agents in cavities extending beyond the cemento-enamel junction, were compared to the sealing abilities of a conventional luting composite (Vita Cerec Duo Cement, Vita) in cavities within sound enamel. SEM analysis and dye penetration were performed to evaluate marginal integrity at the cervical cavity margins. RESULTS: The dentin bonding agent/luting composite combination (Syntac/Dual Cement) rendered a marginal seal within the dentin similar to the quality obtained with the conventional luting procedures within sound enamel. When three out of the five resin-modified glass ionomers were used as luting agents (Dyract, Fuji II LC and Vitremer), the results were comparable to those reported for the dentin bonding agents and the conventional method. SIGNIFICANCE: Light-cured resin-modified glass ionomer cements may be considered as an alternative to dentin bonding agents when the cavity margins of ceramic inlay restorations are within the dentin. However, further studies, e.g., wear resistance, must be performed.     

Histological changes induced by CO2 laser microprobe specially designed for root canal sterilization: in vivo study

Sixty-six class-II CAD/CAM-manufactured ceramic inlays (Cerec) were placed in 27 patients. Each patient received at least one inlay luted with a dual-cured resin composite and one inlay luted with a chemically cured resin composite. The inlays were examined 5 years after luting using the California Dental Association (CDA) criteria. Eighty-nine percent of the 66 inlays were rated 'satisfactory'. During the follow-up period replacement was required for 3 inlays because of inlay fractures (4.5%) and 1 inlay because of fracture of the tooth substance (1.5%). All those inlays were luted with the dual-cured resin composite luting agent. Of the remaining 62 inlays the CDA rating 'excellent' was given to 84% for color, 97% for surface, and 81% for anatomic form. 'Excellent' margin integrity was seen in 52% of the dual-cured resin composite luted inlays and in 61% of the chemically cured resin composite luted inlays. No statistically significant (P> 0.05) difference was observed between the two luting agents.     

A procedure for preparing undecalcified and unembedded bone sections for light microscopy

Recently, new restoratives, such as resin-modified glass ionomer cements (RMGIC) and polyacid-modified resin composites (PMC) were introduced for class III and class V cavities. Both materials use simplified cavity conditioning methods. The well-established treatment of enamel with phosphoric acid has been replaced with treatment using weaker acids. The purpose of this study was to investigate in vivo the quality and durability of the marginal bond to enamel of these restorative system and compare it with a resin composite restorative, Seventeen patients received class III restorations of each of the three restoratives. At baseline and after 1 year replica impressions were made for investigation of the vestibular margins with the scanning electron microscope. Semi-quantitative analysis of the enamel-restorative interfaces was performed at x200 and x1000 magnifications. The three restorative systems showed good marginal adaptation and high percentages of the length of the margins investigated at baseline were gap-free (82%-92%). The resin composite showed significantly better adaptation than the other materials. The marginal quality decreased significantly after 1 year for the resin composite and the polyacid-modified resin composite. The RMGIC showed improved sealing after 1 year in vivo, probably due to continuing water uptake. The percentages of gap-free margins of the total marginal length observed at 1 year were 73%, 90%, and 84%, respectively, for the PMC, the RMGIC and the resin composite. The difference between the PMC and the RMGIC was significant. In conclusion, a good marginal quality was seen for all three restorative systems in class III cavities after a period of 1 year.     

In vitro milling accuracy and fit of 'natural inlays'

OBJECTIVE: This study aimed to investigate the milling behaviour of natural inlays (NI) dental restorations constructed from sound extracted teeth. This was done by comparing the milling accuracy and fit of NI to those of industrial porcelain inlays (PI), milled in the same way. METHODS: A calibration pro-inlay was used to mill three NI and three PI. These were cemented in six acrylic cavities reproduced from the calibration mould, using composite luting cement. No etching and bonding were done. After storage for 24 h in water at room temperature the specimens were sliced buccolingually in a standardised way. For each specimen, two sections were photographed under a light-microscope, resulting in enlarged pictures of the sections. An acetate matrix with the measurement points was placed over each picture in a standardised way. The interfaces between inlays and moulds were measured at 13 fixed points per section using computerised image analysis software. The mean vertical- and floor-interfaces were calculated for each picture, and the overall means were found for each group. Confidence intervals were used for comparison of the differences. The profiles of the milled materials were examined using scanning electron microscopy. RESULTS: There were no differences between NI and PI in the mean interfaces (NI, 102 +/- 8 micrometers; PI, 107 +/- 8 micrometers). Electron microscopy revealed no apparent differences in the profiles of the milled surfaces. CONCLUSION: These findings indicate that the milling accuracy and the fit of natural inlays and milled porcelain inlays are comparable.     

In vitro evaluation of marginal and internal adaptation of class II resin composite restorations after thermal and occlusal stressing

The aim of this in vitro trial was to evaluate the external and internal adaptation of class II composite restorations to tooth structure by means of replica scanning electron microscope (SEM) observation. Standard MOD preparations were cut in human extracted teeth with margins located above and below the cementoenamel junction. Cavities were restored with either a direct multilayered technique, inlays (using conventional or dual DBA application) or prepolymerized composite inserts, using similar restorative material (Syntac, Variolink and Tetric). Evaluations were performed after mechanical and thermocycling. For the marginal adaptation in enamel, the bevelled margins of the direct group resulted in higher percentages of "continuity" (92.5% mesially and 94.6% distally), while the "marginal tooth fracture" was the most commonly found defect in groups with a butt preparation (up to 29.4%, with inserts). For the marginal adaptation in dentin, "continuity" percentages varied from 59% (inlay) to 87.9% (insert). As regards the internal adaptation, results for the whole dentin interface varied from 43.1% (inlay) to 63.9% (inlay with dual bonding) of "continuity". No regional difference in internal adaptation was found between the different preparation areas, except between gingival dentin and gingival enamel (44.9% vs. 80.7% of continuity, all group pooled data). Debonding occurred only at the dentin-restoration interface and consistently took place at the top of the hybrid layer. In the present experimental conditions, the inlay or insert techniques, which make use of the Dual bonding concept, proved to have the best potential to maintain the integrity of dentin-restoration interface.     

An in-vitro investigation of microleakage and gap size of glass ionomer/composite resin "sandwich" restorations in primary teeth

Eighty extracted primary molars were divided into four groups of twenty teeth. Class II cavities were prepared in all teeth with equal numbers of proximal boxes having cavosurface margins either in enamel, or dentin/cementum. Each group was allocated to an open or closed sandwich technique using glass ionomer as a lining. Following the placement of the composite resin restorations, the gap size measured at the proximal box was greatest for the closed sandwich group with the cavosurface margin on enamel (0.203 microns) or dentin/cementum (0.174 microns). Microleakage scores were measured at the proximal box and were greatest for the closed sandwich group with the cavosurface margin on dentin/cementum. The best result was obtained for the open sandwich group with the cavosurface margin on enamel.     

Vertical mammaplasty as secondary surgery after other techniques

The effect of ultrasonic insertion on the filler content and the gap width for two brands of composite resin luting agents, intended for luting with the ultrasonic insertion technique, were studied after MOD ceramic inlays (Cerec) had been placed. In addition, the internal and marginal gap widths were determined after MOD ceramic inlays (Celay) bad been luted on extracted premolars with this technique. No statistically significant differences (P > 0.05) were observed for either brand between the filler content obtained from the internal surfaces, from the excess luting agent, or from the luting agent as delivered. There were no statistically significant differences (P > 0.05) between the final internal and marginal gap widths when the two brands of luting agent were compared with each other. Except for the final occlusal and internal gap widths obtained for the inlays luted with the Sono-Cem luting agent, no statistically significant differences (P > 0.05) were observed between the gap widths at the different locations determined. Thus, the ultrasonic insertion technique used did not significantly influence the filler ratio of the hybrid luting agents studied. Judged by the findings in this study, the properties of luting agents seem to greatly influence the final marginal and internal gap widths.     

Marginal adaptation of resin-bonded light-cured glass ionomers in dentin cavities

PURPOSE: To investigate the marginal adaptation of resin-modified glass ionomer cements in dentin cavities placed with or without additional application of resin bonding systems. MATERIALS AND METHODS: Three resin-modified materials (Fuji II LC, Photac-Fil, Vitremer), one compomer (Dyract) and as reference an adhesively bonded resin composite system (Gluma CPS-Pekafill) were used. Flat peripheral dentin surfaces on human molar teeth were produced by wet grinding on SiC paper. Cylindrical cavities, 3.5 mm wide, were prepared in these dentin areas and restored with the individual materials. Sixty cavities were pretreated and restored as requested by the respective manufacturers. Following water storage of the specimens for 15 minutes or 24 hours, excess was gently removed by wet grinding for microscopic inspection of the marginal area. Additionally, in 30 cavities an experimental one-component adhesive resin system, a proprietary dimethacrylate and HEMA mixture dissolved in acetone, was combined with each of the restoratives for evaluation after 15-minutes water storage. Finally, in six cavities each, Dyract was combined with Prime and Bond 2.0, and Vitremer with Scotchbond Multi-Purpose Plus for assessment after 15 minutes. Maximum marginal gap widths (MGW) were measured. One-way ANOVA by ranks (Kruskal-Wallis-Test) followed by Wilcoxon's Two-Sample test were used to study the statistical difference of MGW among the treatment groups at a rejection level P = 0.05. RESULTS: Neither the conventionally placed material systems nor the restorations in combination with adhesives showed consistently gap-free margins after 15-minute water storage. After 24-hour storage with Vitremer 4 of the 6 restorations were gap-free, whereas with all other materials only perfect margins were registered. There was, however, no significant difference between the groups. Application of the experimental and/or the specific resin bonding agents had no effect on early MGW except for the Photac-Fil group, which was significantly reduced.     

Benefits and disadvantages of tooth-coloured alternatives to amalgam

OBJECTIVES: To give the practising dentist scientifically based data to assist him/her in the responsible decision-making process necessary to weigh the options available to the patient if she/he prefers not to have an amalgam placed. DATA SOURCES: Based on the literature and on the research work, which was done in the author's department, the indications and limitations of the known alternatives of amalgam were formulated. DESCRIPTION OF ALTERNATIVES TO AMALGAM: With the exception of cast gold restorations, all alternatives require the strict use of adhesive techniques. When compared with similar amalgam restorations, placing composite restorations (if they are indicated) takes approximately 2.5 times longer because complex incremental techniques are needed. Despite all the efforts, direct composite restorations placed in large cavities still show unacceptable amounts of marginal openings. Tooth-coloured inlays are a better alternative for large restorations. These restorations must be inserted with adhesive techniques. With composite inlays it is difficult to achieve a composite-composite bond. Ceramic inlays may be micromechanically bonded to the luting composite. They all show clinically a good marginal behaviour and the use of ultrasonic energy may further simplify the application technique of aesthetic inlays. STUDY SELECTION: Papers describing the different techniques were used as a base for the corresponding chapter. To assess and compare the longevity of the different restoration types, literature data were used. We limited ourselves to papers reporting at least 5-year clinical data. Longitudinal, clinically controlled studies were preferred. However, to be more complete, retrospective, cross sectional studies were also included. LONGEVITY OF POSTERIOR RESTORATIONS: Amalgam shows excellent longevity data with studies up to 20 years. The average annual failure rate is 0.3-6.9%. Posterior composites are in the same range (0.5-6.6%), however, the study times are much shorter (max. 10 years). For tooth-coloured inlays much less data are available. Longevity is reported up to 6 years with annual failure rates of 0.6-5%. CONCLUSIONS: All aesthetic alternatives to amalgam require more complex procedures and more time. If cost benefit considerations are a concern, amalgam is still the most convenient restorative material for posterior teeth.     

The effect of the oviduct, uterine, and in vitro environments on zona thinning in the mouse embryo

OBJECTIVE: To evaluate the impact of the oviduct, uterine, and in vitro environments on zona pellucida thinning in the mouse embryo. DESIGN: Female mice were stimulated with pregnant mare serum gonadotropin and mated and hCG injection. Unilateral oviduct ligation was performed on day 2 of gestation using the dorsal approach. The mice were divided into equal groups and killed on days 2, 3, 4, 5, and 10 of gestation. In vitro incubated embryos served as controls. Average daily zona thickness measurements were subjected to analysis of variance and paired Student's t-test. SETTING: The laboratory of the assisted reproductive program of Rush University Medical Center. MAIN OUTCOME MEASURE(S): Progressive daily decrease in average zona thickness. RESULT(S): Zona measurements of embryos flushed out of uterine horns, ligated oviducts, and in vitro incubation demonstrated statistically significant decreases in zona thickness, from 9.6 +/- 1.6 microns (day 3) to 6.0 +/- 0.8 microns (day 5), from 11.6 +/- 2.2 microns (day 2) to 6.0 +/- 1.6 microns (day 5), and from 11.1 +/- 2.0 microns (day 2) to 6.0 +/- 1.6 microns (day 5), respectively. There were no differences in average zona thickness for embryos in the same cell stage and same protocol day in all three locations. CONCLUSION(S): Zona thinning seems to be induced primarily by the dividing embryo before implantation. A substantial tubal and uterine contribution to zona thinning was not detected in this mouse embryo model.     

Surgical management of soft tissue sarcomas: principles of resection and reconstructive plastic procedures

1. Adequate complete surgical resection with a oncologic radical or wide margin of normal tissue represents the most important measure to prevent a local recurrence. Limited excision with "shelling-out" of the tumor, through its "pseudocapsule" almost invariably means positive microscopic margins. The pathohistologically or macroscopically marginal or intralesional positive resection margins make a salvage surgery necessary. 2. A close safety margin of < 1 cm due to neighboured anatomic structures indicates a high risk of local recurrence and makes an adjuvant radiotherapy mandatory. Plastic-reconstructive surgery should prepare the radiotherapy fields, to avoid cavities or ulcerations. 3. Facts should be stated in the clinical record and the operation report, e.g. the safety margin should be defined by the surgeon and the pathologist; the histopathologic stage and grade are absolutely basic requirements. If necessary, a second histopathologic review should be asked for. 4. Tumor resection and reconstructive oncoplastic measures should correspond individually to the oncologic parameters, to the functional demands and to the age of the patient. 5. Multidisciplinary cooperation in a tumorboard is a precondition for an adequate treatment.     

Hyporeactivity of rat diaphragmatic arterioles after exposure to hypoxia in vivo. Role of the endothelium

The effect of prior in vivo hypoxia on the in vitro responses to changes in transmural pressure, alpha-adrenoceptor activation, and depolarization with KCl were evaluated in first-order diaphragmatic arterioles. Rats (n = 14 per group) were exposed to normoxia (controls) or to hypoxia (inspired O2 concentration = 10%) for 12 or 48 h. The arteriolar pressure-diameter relationships were recorded over a pressure range from 10 to 200 mm Hg. In separate groups of arterioles (n = 12 per group), the diaphragmatic arteriolar responses to phenylephrine (10(-8) to 10(-5 M) or KCl (10 to 100 mM) were determined after exposure to either room air or hypoxia for 48 h. In half of the arterioles studied, the endothelium was removed. After 12 h of hypoxia, the pressure-diameter relationship was normal in endothelialized arterioles but was shifted upward in de-endothelialized vessels (p < 0.05). After 48 h of hypoxia, the constrictor response to increasing transmural pressure was severely suppressed in all arterioles. The intraluminal diameters during activation with phenylephrine and KCl were larger in arterioles from rats exposed to hypoxia (103 +/- 8 and 81 +/- 7 microns, respectively) than in control arterioles (41 +/- 5 and 54 +/- 6 microns, respectively; p < 0.05 for differences). During maximum phenylephrine- and KCl-induced constriction in de-endothelialized arterioles, diameters averaged 125 +/- 8 and 105 +/- 8 microns, respectively, for arterioles from hypoxic rats and 32 +/- 6 and 40 +/- 5 microns, respectively, for arterioles from control vessels. Exposure to hypoxia results in impairment of diaphragmatic arteriolar smooth muscle reactivity and reversal of the normal inhibitory influence of the endothelium on diaphragmatic arteriolar tone.     

Long-term results of short segmental syngeneic small intestinal transplantation: comparison of jejunal and ileal grafts

A short-segment intestinal graft is favorable to reduce the rate of rejection and the incidence of graft-versus-host disease in recipients of small intestine transplantation. To determine whether a jejunal or an ileal graft is preferable with respect to intestinal morphology and function, syngeneic two-step small intestinal transplantations were performed using male Lewis rats (RT1(1)). They were divided into two groups according to the small intestine donor site (group 1 received 10 cm of jejunum; group 2 received 10 cm of ileum). There was no significant difference in the survival rate or weight gain between the two groups. Nearly all the hematologic findings, serum nutritional parameters, and results of liver function tests were normal for both groups. The only difference was that the serum total bile acid level was significantly higher in group 2. Fifty weeks after transplantation, the graft mucosa showed normal architecture, with adaptive hyperplasia of villi and crypt noted through histological study. The villus height of group 1 was 595 +/- 64 microns (control, 452 +/- 67 microns); that of group 2 was 732 +/- 53 microns (control, 217 +/- 20 microns). The crypt depth of group 1 was 228 +/- 35 microns (control, 165 +/- 24 microns); that of group 2 was 320 +/- 19 microns (control, 102 +/- 19 microns). These compensatory changes were more pronounced in group 2. The authors conclude that, on the basis of long-term functional capacity, there was no significant difference between jejunal and ileal grafts, and that both segments were suitable for transplantation. However, the ileal graft was considered to be better with respect to morphological adaptation.     

Hematological changes in infectious diseases. Hematological consequences of bacterial, protozoal and spirochetal infections (2)

Thirty-six Class V amalgam restorations were placed in 29 patients. Prior to insertion of the amalgam in 12 cavities the walls were treated with Amalgam Liner and in another 12 cavities with Copalite. The remaining 12 cavities were not treated before amalgam insertion. The margin quality was determined quantitatively with the SEM using replicas obtained immediately after the polishing of the restorations and 6 months later. At baseline the cavities treated with Copalite showed a margin quality identical to the untreated cavities. Cavities treated with Amalgam Liner showed an inferior margin quality. After 6 months the margin quality of the three groups showed no statistical differences. With neither of the liners tested was it possible to improve the margin quality of amalgam restorations.     

Quantification of stromal thinning, epithelial thickness, and corneal haze after photorefractive keratectomy using in vivo confocal microscopy

PURPOSE: The authors establish, for the first time, observer-independent quantification of stromal thinning, epithelial thickness, and corneal haze after excimer laser photorefractive keratectomy (PRK) using a unique, new form of in vivo confocal microscopy. METHODS: Rapid, continuous z-scans of high-resolution confocal images, termed confocal microscopy through focusing (CMTF), were performed in the central corneal area of 17 patients before and 1 month after PRK for low- to moderate-grade myopia (-2.88-9.13 diopters [D]). Corneal, epithelial, and stromal thickness measurements and an objective haze estimate were obtained from each CMTF scan by digital image analysis. RESULTS: Epithelial thickness averaged 51 +/- 4 microns before and 45 +/- 10 microns 1 month post-PRK (P < 0.005), whereas stromal thinning ranged from 20 to 154 microns, representing a direct estimate of the actual photoablation depth. Corneal thickness averaged 560 +/- 36 microns before PRK and 462 +/- 52 microns at 1 month. The change in corneal thickness correlated closely with the change in spherical equivalent refraction (r = 0.94, P < 0.0001); linear regression analysis revealed a value of 14.3 microns corneal thinning per diopter of correction. A significant correlation was found between the objective CMTF haze estimate and a clinical haze grading obtained by slit-lamp examination (r = 0.73, P < 0.001). CONCLUSIONS: Confocal microscopy through focusing is a new, powerful in vivo tool that enables quantitative, unbiased evaluation of PRK procedures over time by providing epithelial and stromal thickness analysis, photoablation depth assessment, and unbiased haze measurement. The method is uniquely valuable in the pre- and postoperative assessment of PRK patients and for determining the optimal treatment strategy, especially in assessing refractive and visual outcomes in individual cases.     

Basal cell carcinoma of the eyelid. Risk of recurrence according to adequacy of surgical margins

PURPOSE: To examine all basal cell carcinomas of the eyelid diagnosed in Iceland during a 25-year period, paying special attention to the surgical margins of excision in relation to recurrence. Based on the results a simple, clinically relevant method of classifying the surgical margin is proposed. METHODS: All histologically proven basal cell cancer specimens from eyelids were reviewed retrospectively. The surgical excision margins were classified as radical, marginal or intralesional. RESULTS: Recurrence risk was low when the tumor had a surgical margin described as radical or marginal. The recurrence rate was 38% when the margin was intralesional. CONCLUSION: By assessing the surgical margins by this method, which is easy to apply, better understanding between the pathologist and the surgeon may be achieved.     

Physical and cytochemical properties of neutrophils activated in situ in the lung during ZAP infusion in sheep

Increased retention of activated neutrophils in the lungs contributes to endothelial cell injury. However, characterization of the morphological changes that occur in neutrophils during activation in the pulmonary microcirculation has not been fully determined in vivo. Therefore, the present study was designed to determine structural and cytochemical properties of neutrophils in situ in pulmonary arterioles and alveolar capillaries during the infusion of zymosan-activated plasma (ZAP) or plasma (control) in anesthetized sheep. Quantitative morphological methods showed that ZAP infusion caused significant retention of neutrophils in alveolar capillaries [2.19 +/- 0.40 (SD) x 10(8) neutrophils/ml of capillary blood volume] and pulmonary arterioles (1.02 +/- 0.46 x 10(8) neutrophils/ml of arterial blood volume) compared with plasma infusion (1.03 +/- 0.15 and 0.30 +/- 0.10 x 10(8) neutrophils/ml, respectively; P < 0.05). Harmonic mean diameter of ZAP-activated neutrophils in situ (7.19 +/- 0.44 microns) was significantly greater than the diameter of neutrophils in plasma-treated sheep (6.29 +/- 0.17 microns; P < 0.05). Neutrophil cross-sectional area (54 +/- 3 microns2) and volume (248 +/- 27 microns3) in situ in alveolar capillaries were also significantly greater in ZAP-treated sheep than in control sheep (41 +/- 4 microns2 and 184 +/- 9 microns3, respectively; P < 0.05). Similarly, microvascular neutrophils in ZAP-treated sheep were vacuolated and elongated, filamentous actin was redistributed peripherally, and the cells were degranulated. We conclude that during ZAP infusion, neutrophils become enlarged and degranulated in pulmonary microvessels, especially in alveolar capillaries. The structural and cytochemical changes that occur are consistent with the hypothesis that neutrophil activation is accompanied by alterations in neutrophil physical properties, alterations that may facilitate retention and contribute to endothelial cell injury.     

Caries diagnosis with dye-staining at amalgam restoration margins

PURPOSE: To determine the strength of agreement between detection of caries at the margin of amalgam restorations with a caries detector dye, and detection of caries histologically utilizing light/polarizing light microscopy. MATERIALS AND METHODS: 17 permanent molars with intact amalgam restorations, determined to be caries-free by visual inspection and explorer probing, cleansed with an air/water/abrasive slurry system, and with evidence of amalgam enamel marginal staining from application of a 1% solution of sulforhodamine B caries detector dye were utilized. Longitudinal, undecalcified sections, 80-100 micrometers thick, were prepared including stained and unstained regions of the amalgam/enamel margin of each tooth, providing 34 margins for study. The sections were examined in the light/polarizing light microscope for evidence of marginal caries. The Kappa Index was calculated to determine the strength of agreement between the caries dye method and the light/polarizing light microscopic method of caries diagnosis. RESULTS: Microscopically, caries was detected in 14 of 34 margins (41%). Agreement for presence of caries was 5 of 34, and for absence of caries 8 of 34 (total agreement 38%). 12 of 17 dye-stained margins were microscopically caries-free, and 9 of 17 unstained margins had caries microscopically. Kappa Index for these findings was 0.23, indicating poor strength of agreement.