Recycling process assessment of mechanical recycling of printed circuit board

A comprehensive assessment index system was established. The mechanical recycling process of printed circuit board was evaluated according to the comprehensive evaluation index system using the fuzzy analytic hierarchy process. A process assessment software system of mechanical recycling was established to evaluate different recy cling technologies. And the software system was developed in the environment of VB 6.0 and Access 2000.     

Key technologies of layout design of recycling plants of waste refrigerators

The present situations of waste refrigerators recycling and disposing were analyzed. Three key technologies of layout design of recycling plants of waste refrigerators were presented as follows: 1) establishment of recycling process of waste refrigerators; 2) the general plane layout of recycling plants; 3) the detailed layout of workshops of recycling plants. The focus of the three key technologies is to tackle the problem of the detailed layout of workshops of the recycling plants. By adopting Petri net, the model of logistics system of workshops was established and then optimized, and finally the detailed layout chart of recycling plants was gained. By adopting E-factory, the recycling plants were simulated. The results show that the method mentioned is effective. Foundation item: Project(50375044) supported by the National Natural Science Foundation of China     

End-of-life vehicle recycling based on disassembly

The end-of-life vehicle recycling was studied based on the disassembly. The end-of-life recycling and the disassembly were reviewed and discussed. A disassembly experiment of an end-of-life engine was carried out, which strictly recorded the process of dismantling. Based on the results, a model of the end-of-life recycling was presented. In this model, the end-of-life parts were classified by three ways which included to recycle directly, to recycle after remanufacturing and to discard. By using this model, the dismantling efficiency and the recycling rate can be improved. Also, it obtains a good result after used in a dismantling factory. Foundation item: Key Project (50235030) supported by the National Natural Science Foundation of China     

Using hybrid modeling for life cycle assessment of motor bike and electric bike

Life-cycle assessment (LCA) is environmental evaluation of products, materials, and processes over their life cycle. Truncation uncertainty and corresponding uncertainty are main problems occurred in process life cycle assessment (PLCA) modeling and economic input-output life cycle assessment (EIOLCA) modeling. Through combination of these two modelings in different life cycle stage and use of an uncertainty reduction strategy, a hybrid life cycle assessment modeling method was proposed in this study. Case studies were presented on gasoline-powered motorbikes (M-bike) and electricity-powered electric bike (E-bike). Web-based software was developed to analyze process environmental impacts. Results show that the largest part of life cycle energy (LCE) is consumed at use stage. Less energy is consumed in life cycle of E-bike than that of M-bike. GWP (Global Warming Potential), CO (Carbon Monoxide), PM10 (particulate matter) emission of M-bike are higher than that of E-bike, especially at use stage, AP (acidification Potential) emission of E-bike is higher than that of M-bike. Comprehensively, E-bike is energy efficient and less emitting, and better choice for urban private transportation. Foundation item: Project (G-0205-06347) supported by David and Lucile Packard Foundation in Partnership with the US Energy Foundation; Project (ICA4-2002-10023) supported by European Union     

Delay-independent decentralized H ∞ control for multi-channel discrete-time systems with uncertainties

A robust decentralized H∞ control problem was considered for uncertain multi-channel discrete-time systems with time-delay. The uncertainties were assumed to be time-invariant, norm-bounded, and exist in the system, the time-delay and the output matrices. Dynamic output feedback was focused on. A sufficient condition for the multi-channel uncertain discrete time-delay system to be robustly stabilizable with a specified disturbance attenuation level was derived based on the theorem of Lyapunov stability theory. By setting the Lyapunov matrix as block diagonal appropriately according to the desired order of the controller, the problem was reduced to a linear matrix inequality （LMI） which is sufficient to existence condition but much more tractable. An example was given to show the efficiency of this method.     

Modeling and simulation of crushing process of spiral mining head

1 INTRODUCTIONThe research of mining deep seabed cobalt-richcrust is a hotspot of international oceanology[1].Based on the mining manganese nodule ,lots of re-searches on mining cobalt crust have been madedeeply and many kinds of methods ,such as thei m-proved CLB, mining vehicle +lifting system +surface supporting ship have been put forward.Mining vehicle consists of collecting machine ,tracked treading machine and spiral mininghead[2 ,3].The first step of mining cobalt crust is tocrush…     

Relationship between rheological manufacturing process and optical performance of optical fiber coupler

Through theoretical analysis and experiments, the viscoelastic mechanical model of optical fiber coupler in the process of fused biconical taper was established, and the numerical analysis in non-uniform temperature field was made. The results show that the rheological parameters, such as drawing speed and fused temperature, have a tremendous influence on stress distribution and performance of optical fiber coupler, especially the influence of fused temperature. The change of fused temperature by 5 ℃ can lead to the change of the maximum stress by 30% and stress difference by 20% in the same cross section. The change of temperature gradient by 3% can result in the change of stress difference by 90%. In the present condition of rheological technology, rheological defects such as crystallizations and microcracks are easy to generate in the optical fiber coupler.     

Preparation of ultrafine Ti(C, N)-based cermet using oxygen-rich powders

The availability using oxygen-rich powders to prepare ultrafine Ti(C,N)-based cermets was investigated. The deoxidation process, denitrification phenomenon and the effect of deoxidation on microstructure and mechanical properties of sintered samples were discussed, respectively. The results show that oxygen in the samples prepared even with high oxygen contained in starting powders can be almost completely cleaned away through suitable sintering process. The ultrafine oxygen-rich powders have a significant effect on microstructure, which promotes the formation of white core phase. A ultrafine Ti(C,N)-based cermet with mean particle size of 0.30 μm, uniform microstructure and excellent mechanical properties is successfully prepared. It is also found that there exists severe denitrification phenomenon in the preparation process of ultrafine Ti(C,N)-based cermet. Foundation item: Project(50323008) supported by the National Natural Science Foundation of China     

Statistical damage model for quasi-brittle materials under uniaxial tension

Based on the parallel bar system, combining with the synergetic method, the catastrophe theory and the acoustic emission test, a new motivated statistical damage model for quasi-brittle solid was developed. Taking concrete for instances, the rationality and the flexibility of this model and its parameters-determining method were identified by the comparative analyses between theoretical and experimental curves. The results show that the model can simulate the whole damage and fracture process in the fracture process zone of material when the materials are exposed to quasi-static uniaxial tensile traction. The influence of the mesoscopic damage mechanism on the macroscopic mechanical properties of quasi-brittle materials is summarized into two aspects, rupture damage and yield damage. The whole damage course is divided into the statistical even damage phase and the local breach phase, corresponding to the two stages described by the catastrophe theory. The two characteristic states, the peak nominal stress state and the critical state are distinguished, and the critical state plays a key role during the whole damage evolution course. Foundation item: Projects(90510018, 50679006) supported by the National Natural Science Foundation of China; Project(NCET-05-0413) support by the Program for New Century Excellent Talents in University     

Design and dynamic simulation of hydraulic system of a new automatic transmission

A new hydraulic system of a novel automatic transmission (AT) was designed. The dimension and structure of valves and cylinders were designed by theoretical calculation. The dynamic simulation model of hydraulic system of AT was established by ITI-SimulationX. Simulation results and theoretical design results were compared to confirm the simulation model. Based on the confirmed simulation model, the simulation results of pressure and flow of the hydraulic system were analyzed. The dynamic simulation method is very helpful for designing and analyzing the performance of hydraulic system and further optimization design. The theoretical design method and dynamic simulation model are feasible for the real industrial applications. The research results can be used in hydraulic system design and optimization. Foundation item: Project(911901204) supported by Youth Innovation Foundation of Beijing University of Aeronautics and Astronautics     

Application of empirical mode decomposition based energy ratio to vortex flowmeter state diagnosis

To improve the measurement performance, a method for diagnosing the state of vortex flowmeter under various flow conditions was presented. The raw sensor signal of the vortex flowmeter was adaptively decomposed into intrinsic mode functions using the empirical mode decomposition approach. Based on the empirical mode decomposition results, the energy of each intrinsic mode function was extracted, and the vortex energy ratio was proposed to analyze how the perturbation in the flow affected the measurement performance of the vortex flowmeter. The relationship between the vortex energy ratio of the signal and the flow condition was established. The results show that the vortex energy ratio is sensitive to the flow condition and ideal for the characterization of the vortex flowmeter signal. Moreover, the vortex energy ratio under normal flow condition is greater than 80%, which can be adopted as an indicator to diagnose the state of a vortex flowmeter. Foundation item: Project(200801346) supported by the China Postdoctoral Science Foundation; Project(2008RS4022) supported by the Hunan Postdoctoral Scientific Program; Project(2008) supported by the Postdoctoral Science Foundation of Central South University     

Directly searching method for slip plane and its influential factors based on critical state of slope

In order to determine the slip plane of slope directly by the calculation results of strength reduction method, and analyze the influential factors of slope stability, a numerical model was established in plane strain mode by FLAC3D for homogeneous soil slope, whose parameters were reduced until the slope reached the critical state. Then FISH program was used to get the location data of slip plane from displacement contour lines. Furthermore, the method to determine multiple slip planes was also proposed by setting different heights of elastic areas. The influential factors for the stability were analyzed, including cohesion, internal friction angle, and tensile strength. The calculation results show that with the increase of cohesion, failure mode of slope changes from shallow slipping to the deep slipping, while inclination of slip plane becomes slower and slipping volume becomes larger; with the increase of friction angle, failure mode of slope changes from deep slipping to shallow slipping, while slip plane becomes steeper and upper border of slip plane comes closer to the vertex of slope; the safety factor increases little and slip plane goes far away from vertex of slope with the increase of tensile strength. Foundation item: Project(20060533071) supported by the Doctoral Program Foundation of Higher Education of China; Project (20060400264) supported by China Postdoctoral Science Foundation; Project (50774093) supported by the National Natural Science Foundation of China; Project (1343-74236000014) supported by Graduate Student Innovation Foundation of Hunan Province, China     

Decision-making of biomass ethanol fuel policy based on life cycle 3E assessment

To evaluate the environmental, economic, energy performance of biomass ethanol fuel in China and to support the decision-making of biomass ethanol energy policy, an assessment method of life cycle 3E (economy, environment, energy) was applied to the three biomass ethanol fuel cycle alternatives, which includes cassava-based, corn-based and wheat-based ethanol fuel. The assessments provide a comparison of the economical performance, energy efficiency and environmental impacts of the three alternatives. And the development potential of the three alternatives in China was examined. The results are very useful for the Chinese government to make decisions on the biomass ethanol energy policy, and some advises for the decision-making of Chinese government were given. Foundation item: Project (50175070) supported by the National Natural Science Foundation of China; Project (G-0205-06347) supported by European Commission Funding     

Experimental study on wear failure course of gas-valve/valve-seat in engine

The wear failure course of gas-valve/valve-seat in engine was investigated with a simulating tester. The results show that the failure of the contact conical surface is mainly caused by the elastic and plastic deformation and the fatigue micro-crack and spalling. The creep-deformation and corrosion atmosphere accelerated wear failure course at the high temperature. The wear failure course of the gas-valve/valve-seat in engine follows general wear rules of mechanical elements, but the rate of wear in the sharp wear stage is faster. Foundation item: Project supported by Postdoctoral Foundation of Central South University; project (04B035) supported by the Youth Foundation of Hunan Province Education Bureau     

Dynamic services selection algorithm in Web services composition supporting cross-enterprises collaboration

Based on the deficiency of time convergence and variability of Web services selection for services composition supporting cross-enterprises collaboration, an algorithm QCDSS (QoS constraints of dynamic Web services selection) to resolve dynamic Web services selection with QoS global optimal path, was proposed. The essence of the algorithm was that the problem of dynamic Web services selection with QoS global optimal path was transformed into a multi-objective services composition optimization problem with QoS constraints. The operations of the cross and mutation in genetic algorithm were brought into PSOA (particle swarm optimization algorithm), forming an improved algorithm (IPSOA) to solve the QoS global optimal problem. Theoretical analysis and experimental results indicate that the algorithm can better satisfy the time convergence requirement for Web services composition supporting cross-enterprises collaboration than the traditional algorithms. Foundation item: Project(70631004) supported by the Key Project of the National Natural Science Foundation of China; Project(20080440988) supported by the Postdoctoral Science Foundation of China; Project(09JJ4030) supported by the Natural Science Foundation of Hunan Province, China; Project supported by the Postdoctoral Science Foundation of Central South University, China     

Synthesis and photophysical and electrochemical properties of new cyclometalated platinum complex containing oxadiazole ligand

A new cyclometalated platinum complex containing 2, 5-bis（naphthalene-1-yl）-1,3,4-oxadiazole ligand was synthesized and characterized. The UV-Vis absorptions and photoluminescent properties of the ligand and its platinum complex were investigated A characteristic metal-ligand charge transfer absorption peak at 439 nm in the UV spectrum and a strong emission peak at 625 nm in the photoluminescence spectrum were observed for this complex in dichloromethane. Cyclic voltammtry （CV） analysis shows that the EHOMO （energy level of the highest occupied molecular orbital） and ELUMO （energy level of the lowest unoccupied molecular orbital） of the platinum complex are about -5.69 and -3.25 eV, respectively, indicating that the oxadiazole-based platinum complex has a potential application in electrophosphorescent devices used as a red-emitting material.     

Electron bandstructure of kaolinite and its mechanism of flotation using dodecylamine as collector

The bulk electronic structure of kaolinite (001) plane was studied with quantum mechanical calculations. The CASTEP parameterization of ultrasoft pseudopotentials without core corrections was used to optimize the structure of kaolinite bulk and slab models. The results show that Fermi energy of kaolinite (001) plane is 3.05 eV, and the band gap is 4.52 eV. The partial density of states (PDOS) of kaolinite (001) plane indicates that Al—O and Si—O bonds on the mineral surface are highly polar. The oxygen atoms of hydroxyl groups in surface layer are capable of forming hydrogen bond with the head group of cationic collectors. The properties of dodecylamine (DDA) cation were also calculated by density function theory (DFT) method at B3LYP/6-31G (d) level for illuminating the flotation processes of kaolinite. Besides the electrostatic attraction, the mechanism between kaolinite and DDA is found to be hydrogen bonds under acidic condition. Foundation item: Project(2005CB623701) supported by the Major State Basic Research and Development Program of China; Project(50874118) supported by the National Nature Science Foundation of China; Project(2007B52) supported by the Foundation for the Author of National Excellent Doctoral Dissertation of China     

Life cycle of remanufactured engines

The life cycle index of remanufactured engines was assessed by using the method of life cycle assessment (LCA). A remanufactured engine of a certain domestic brand was taken as researching object. Engine reproducing engineering was investigated from three aspects which were energy, material and environment. The application of LCA on remanufacturing engines was discussed in detail with a practical case. The results indicate that remanufacturing an engine can save 55 kg steels, 8.3 kg aluminum and 113 kW · h electric powers and reduce emissions of 565 kg CO₂, 6.09 kg CO, 1.01 kg NO _x , 3.985 kg SO _x and 288.725 kg solid waste. The remanufacturing of engines possesses great economic value and practicability. Foundation item: Project (50235030) supported by the National Natural Science Foundation of China     

Automatic brush-plating technology for component remanufacturing

An automatic brush-plating system was developed for component remanufacturing. With this system, Ni/nano-alumina composite coatings from an electrolyte containing 20 g/L nano-alumina particles were prepared. Microstructure, surface morphology, microhardness and wear resistance of automatically plated coating and manually plated coatings were investigated comparatively. The results show that the automatically plated coatings are relatively dense and uniform and have lower friction coefficient of 0.089 under lubricant condition, when compared with manually plated coatings with friction coefficient of 0.14. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China; Project(G1999065009) supported by the National Basic Research Program of China     

Influences of seed size and number on agglomeration in synthetic Bayer liquors

By means of Malvern laser particle size analyzer and scanning electron microscopy, the influences of seed size and number on agglomeration in Bayer process were investigated. Agglomeration is almost finished in 8 h, seeds, below 5 μm, especially below 2 μm, gather together rapidly and almost disappear in 8 h. In the same supersaturation of aluminate solution and seed size, the smaller the number of seed is, the bigger the degree of agglomeration is. With the same primary number of seed, the agglomeration of larger seed is superior to that of small seed, and the agglomeration does not happen among the coarse seeds. The agglomeration mainly happens among fine particles, and the combinations among the fine particles are unconsolidated.