A low power, low noise figure quadrature demodulator for a 60 GHz receiver in 65-nm CMOS technology

This paper presents the design of a low power (LP) and a low noise figure (NF) quadrature demodulator with an on-chip frequency divider for quadrature local oscillator (LO) signal generation. The transconductance stage of the mixer is implemented by an AC-coupled self-bias current reuse topology. On-chip series inductors are employed at the gate terminals of the differential input transconductance stage to improve the voltage gain by enhancing the effective transconductance. The chip is implemented in 65-nm LP CMOS technology. The demodulator is designed for an input radio frequency (RF) band ranging from 10.25 to 13.75 GHz. A fixed LO frequency of 12 GHz down-converts the RF band to an intermediate frequency (IF) band ranging from DC to 1.75 GHz. From 10 MHz to 1.75 GHz the demodulator achieves a voltage conversion gain (VCG) ranging from 14.2 to 13.2 dB, and a minimum single-sideband NF (SSB-NF) of 9 dB. The measured third-order input intercept point (IIP₃) is -3.3 dBm for a two-tone test frequency spacing of 1 MHz. The mixer alone draws a current of only 2.5 mA, whereas the complete demodulator draws a current of 7.18 mA from a 1.2 V supply. The measurement results for a frequency divider, which was fabricated individually, prior to being integrated with the quadrature demodulator, in 65-nm LP CMOS technology, are also presented in this paper.     

宽中频CMOS下变频器单片

该文介绍了一种工作于毫米波频段的宽中频(IF)下变频器。该下变频器基于无源双平衡的设计架构,片上集成了射频(RF)和本振(LO)巴伦。为了优化无源下变频器的增益、带宽和隔离度性能,电路设计中引入了栅极感性化技术。测试结果表明,该下变频器的中频带宽覆盖0.5～12 GHz。在频率为30 GHz、幅度为4 dBm的LO信号驱动下,电路的变频增益为–8.5～–5.5 dB。当固定IF为0.5 GHz、LO幅度为4 dBm时,变频增益随25～45 GHz的RF信号在–7.9～–5.9 dB范围内变化,波动幅度为2 dB。LO-IF, LO-RF, RF-IF的隔离度测试结果分别优于42, 50, 43 dB。该下变频器芯片采用TSMC 90 nm CMOS工艺设计,芯片面积为0.4 mm2。     

A 0.7-7 GHz wideband reconfigurable receiver RF front-end in CMOS

In this paper,a 0.7-7 GHz wideband RF receiver front-end SoC is designed using the CMOS process.The front-end is composed of two main blocks:a single-ended wideband low noise amplifier (LNA) and an inphase/quadrature (I/Q) voltage-driven passive mixer with IF amplifiers.Based on a self-biased resistive negative feedback topology,the LNA adopts shunt-peaking inductors and a gate inductor to boost the bandwidth.The passive down-conversion mixer includes two parts:passive switches and IF amplifiers.The measurement results show that the front-end works well at different LO frequencies,and this chip is reconfigurable among 0.7 to 7 GHz by tuning the LO frequency.The measured results under 2.5-GHz LO frequency show that the front-end SoC achieves a maximum conversion gain of 26 dB,a minimum noise figure (NF) of 3.2 dB,with an IF bandwidth of greater than 500 MHz.The chip area is 1.67 × 1.08 mm2.     

A 9–31-GHz Subharmonic Passive Mixer in 90-nm CMOS Technology

A subharmonic down-conversion passive mixer is designed and fabricated in a 90-nm CMOS technology. It utilizes a single active device and operates in the LO source-pumped mode, i.e., the LO signal is applied to the source and the RF signal to the gate. When driven by an LO signal whose frequency is only half of the fundamental mixer, the mixer exhibits a conversion loss as low as 8–11 dB over a wide RF frequency range of 9–31GHz. This performance is superior to the mixer operating in the gate-pumped mode where the mixer shows a conversion loss of 12–15dB over an RF frequency range of 6.5–20 GHz. Moreover, this mixer can also operate with an LO signal whose frequency is only 1/3 of the fundamental one, and achieves a conversion loss of 12–15dB within an RF frequency range of 12–33 GHz. The IF signal is always extracted from the drain via a low-pass filter which supports an IF frequency range from DC to 2 GHz. These results, for the first time, demonstrate the feasibility of implementation of high-frequency wideband subharmonic passive mixers in a low-cost CMOS technology.     

Design of high-linearity 75–90 GHz CMOS down-conversion mixer for automotive radar

This paper presents a 75–90 GHz down-conversion mixer applied in automotive radar, which is characterized with high linearity, low local oscillator (LO) drive as well as high conversion gain (CG) using TSMC 65-nm CMOS general-purpose technology. The good linearity and isolation of mixer are required for automotive radar to cover short-middle-far range detection. The mixer includes an enhanced double-balanced Gilbert-cell core with series peaking transmission line and source degeneration technique for improving linearity and CG, two on-chip baluns and intermediate frequency (IF) buffer for IF test. Besides, to make the design more accurate and efficient, the modeling and design of millimeter-wave (mm-wave) passive devices are introduced. The mixer consumes 12 mW under 1.5 V. The input 1 dB compression point (P_1dB) is 2.5 dBm as well as IIP3 of 13.2 dBm at 80 GHz. High performances are achieved with the CG of 5 dB at 76 GHz with LO power of 0 dBm for frequencies of 75–90 GHz which covers the application of automotive radar frequency band (76–81 GHz) and LO-RF isolation of 33–37 dB for frequencies of 60–90 GHz. The area of the mixer is 0.14 mm², with PADs included.     

一种高线性无源双平衡混频器

设计了一种适用于1.0～2.0 GHz的高线性下变频混频器。电路设计采用了无源双平衡结构,片内集成宽带巴伦、限幅本振放大器、混频核和偏置电路。为了提高混频器的线性度,在对无源双平衡的结构进行分析的基础上,折中选择混频核的晶体管尺寸,并优化了本振放大器输出信号的幅值及上升时间。基于0.35μm BiCMOS工艺进行了设计仿真,芯片面积为0.9 mm×1.8 mm。流片测试结果表明:射频频率1.0～2.0 GHz,对应本振频率1.0～2.0 GHz,最佳本振输入功率为0 dBm,转换增益大于-7.0 dB,射频输入三阶交调大于25 dBm,混频器工作电压为3.3 V,功耗为112 mW。该高线性无源双平衡混频器可满足工程应用。     

A 2.4-GHz ISM-Band Sliding-IF Receiver With a 0.5-V Supply

We report an ultra-low-voltage RF receiver for applications in the 2.4 GHz band, designed in a 90 nm CMOS technology. The sliding-IF receiver prototype includes an LNA, an image-reject LC filter with single-ended to differential conversion, an RF mixer, an LC IF filter, a quadrature IF mixer, RF and IF LO buffers, and an I/Q baseband section with a VGA and a low-pass channel-select filter in each path, all integrated on-chip. It has a programmable overall gain of 30 dB, noise figure of 18 dB, out-of-channel IIP3 of -22 dBm. The 3.4 mm² chip consumes 8.5 mW from a 0.5 V supply.     

A 10–35 GHz Low Power Bulk-DrivenMixer Using 0.13 $mu$m CMOS Process

10-35 GHz doubly balanced mixer using a 0.13-mum CMOS foundry process is presented in this letter. Using the bulk-driven topology, the number of transistors of the doubly balanced mixer is reduced; thus the mixer can achieve a low supply voltage and low power consumption. This bulk-driven mixer exhibits a measured conversion gain of -1 plusmn 2 dB from 10 to 35 GHz of radio frequency (RF) with a fixed intermediate frequency (IF) of 100 MHz. The measured local oscillation (LO) to IF and RF-IF isolations are better than 30 dB. The chip area of the mixer is 0.6 times 0.4 mm². The total power consumption included output buffer is only 6 mW.     

Broadband single- and double-balanced resistive HEMT monolithicmixers

A double-balanced (DB) 3-18 GHz and a single-balanced (SB) 2-16 GHz resistive HEMT monolithic mixer have been successfully developed. The DB mixer consists of a AlGaAs/InGaAs HEMT quad, an active LO balun, and two passive baluns for RF and IF. At 16 dBm LO power, this mixer achieves the conversion losses of 7.5-9 dB for 4-13 GHz RF and 7.5-11 dB for 3-18 GHz RF. The SB mixer consists of a pair of AlGaAs/InGaAs HEMT's, an active LO balun, a passive IF balun and a passive RF power divider. At 16 dBm LO power, this mixer achieves the conversion losses of 8-10 dB for 4-15 GHz RF and 8-11 dB for 2-16 GHz RF. The simulated conversion losses of both mixers are very much in agreement with the measured results. Also, the DB mixer achieves a third-order input intercept (IP₃) of +19.5 to +27.5 dBm for a 7-18 GHz RF and 1 GHz IF at a LO drive of 16 dBm while the SB mixer achieves an input IP ₃ of +20 to +28.5 dBm for 2 to 16 GHz RF and 1 GHz IF at a 16 dBm LO power. The bandwidth of the RF and LO frequencies are approximately 6:1 for the DB mixer and 8:1 for the SB mixer. The DB mixer of this work is believed to be the first reported DB resistive HEMT MMIC mixer covering such a broad bandwidth     

Design and implementation of a 94 GHz CMOS down-conversion mixer with integrated miniature planar baluns for image radar sensors

A 94 GHz down-conversion mixer for image radar sensors using standard 90 nm CMOS technology is reported. The down-conversion mixer comprises a double-balanced Gilbert cell with peaking inductors between RF transconductance stage and LO switching transistors for conversion gain (CG) enhancement and noise figure suppression, a miniature planar balun for converting the single RF input signals to differential signals, another miniature planar balun for converting the single LO input signals to differential signals, and an IF amplifier. The mixer consumes 22.5 mW and achieves excellent RF-port input reflection coefficient of ?10 to ?35.9 dB for frequencies of 87.6–104.4 GHz, and LO-port input reflection coefficient of ?10 to ?31.9 dB for frequencies of 88.2–110 GHz. In addition, the mixer achieves CG of 4.9–7.9 dB for frequencies of 81.8–105.8 GHz (the corresponding 3-dB CG bandwidth is 24 GHz) and LO–RF isolation of 37.7–47.5 dB for frequencies of 80–110 GHz, one of the best CG and LO–RF isolation results ever reported for a down-conversion mixer with operation frequency around 94 GHz. Furthermore, the mixer achieves an excellent input third-order intercept point of ?3 dBm at 94 GHz. These results demonstrate the proposed down-conversion mixer architecture is promising for 94 GHz image radar sensors.     

毫米波宽带高中频单平衡混频器设计与实现

针对毫米波宽带通信、雷达和测试仪器领域的应用需求,提出一种E波段宽带高中频(IF)单平衡混频器。射频(RF)及本振(LO)信号通过多分支宽带加宽波导正交耦合器输入,通过鳍线过渡结构将信号从波导传输模式过渡到微带模式,并提供宽带中频信号及直流接地回路;中频输出低通滤波器可有效抑制LO及RF信号,并为其提供等效接地回路。利用肖特基二极管的非线性实现混频,并通过微带匹配电路最终实现宽带低损耗混频效果。混频器采用57.6、62.4、67.2 GHz 3个点频本振,将67~85 GHz的射频信号分段下变频至9.4~17.8 GHz的中频范围内。测试结果表明,在67~85 GHz射频频率范围内,射频输入功率为-15 dBm,本振输入功率为12 dBm时,混频器变频损耗为7.1~10.1 dB,对组合杂散的抑制在36 dBc以上。     

A low-noise mixer with an image-reject notch filter for 2.4 GHz applications

This paper presents a low noise first down-conversion mixer with a notch filter for the heterodyne receiver. The notch filter connected to the output node of the mixer driver stage plays a role of image rejection at an image frequency, thereby suppressing the sideband image noise and improving the mixer noise performance. Targeted for 2.4 GHz industrial-scientific-medical band applications, a simple source-degenerated down-conversion single balanced mixer with the filter is implemented. The measurement results of the proposed down-conversion mixer shows about 3.0 dB improvement of single-side band noise figure, about 2.9 dB power conversion gain improvement, and 25 dB image suppression compared to those without the filter dissipating 4 mA from a 2.5 V supply voltage.     

12-GHz-Band GaAs Dual-Gate MESFET Monolithic Mixers

12-GHz-band GaAs dual-gate MESFET monolithic mixers have been developed for use in direct broadcasting satellite receivers. In order to reduce chip size, a buffer amplifier has been connected directly after a mixer IF port, instead of employing an IF matching circuit. The mixer and the buffer were fabricated on separate chips, so that individual measurements could be achieved. Chip size is 0.96X 1.26 mm for the mixer and 0.96X0.60 mm for the buffer. A dual-gate FET for the mixer, as well as a single-gate FET for the buffer, has a closely spaced electrode structure. Gate length and width are 1 µm and 320 µm, respectively. The mixer with the buffer provides 2.9+-0.4-dB conversion gain with 12.3+-0.3dB SSB noise figure in the 11.7-12.2-GHz RF band. Local oscillator (LO) frequency is 10.8 GHz. A low-noise converter was constructed by connecting a monolithic preamplifier, an image rejection filter, and a monolithic IF amplifier to the mixer. The converter provides 46.8+-1.5-dB conversion gain with 2.8+-0.2-dB SSB noise figure in the same frequency band.     

A 90–96 GHz CMOS down-conversion mixer with high conversion gain and excellent LO–RF isolation

A 90–96 GHz down-conversion mixer for 94 GHz image radar sensors using standard 90 nm CMOS technology is reported. RF negative resistance compensation technique, i.e. NMOS LC-oscillator-based RF transconductance (GM) stage load, is used to increase the output impedance and suppress the feedback capacitance C_gd of RF GM stage. Hence, conversion gain (CG), noise figure (NF) and LO–RF isolation of the mixer can be enhanced. The mixer consumes 15 mW and achieves excellent RF-port input reflection coefficient of ?10 to ?36.4 dB for frequencies of 85–105 GHz. The corresponding -10 dB input matching bandwidth is 20 GHz. In addition, for frequencies of 90–96 GHz, the mixer achieves CG of 6.3–9 dB (the corresponding 3-dB CG bandwidth is greater than 6 GHz) and LO–RF isolation of 40–45.1 dB, one of the best CG and LO–RF isolation results ever reported for a down-conversion mixer with operation frequency around 94 GHz. Furthermore, the mixer achieves an excellent input third-order intercept point of 1 dBm at 94 GHz. These results demonstrate the proposed down-conversion mixer architecture is very promising for 94 GHz image radar sensors.     

A compact 220 GHz heterodyne receiver module with planar Schottky diodes

This letter presents the development of a compact 220 GHz heterodyne receiver module for radars application in which a novel low pass wide stop band intermediate frequency (IF) filter is integrated. The planar Schottky anti-parallel mixing diode based subharmonic mixer (SHM) is used as the receiver’s first stage. The diode is flip-chip mounted on a 50 μm thick quartz substrate. The accurate modeling of the self and mutual inductance of the diode’s air-bridges are discussed. The measured conversion loss (CL) of the SHM has a minimum value of 6.2 dB at 210.5 GHz, and is lower than 8.4 dB in the frequency range 209.4–219.6 GHz with a 10 mW input power from a local oscillator (LO). The LO chain consists of a 110 GHz passive tripler, two Ka-band amplifiers and a Ka-band active tripler. The tested minimum double side band (DSB) noise temperature of the integrated 220 GHz heterodyne receiver is 725 K at 205.2 GHz and lower than 1550 K in the frequency range 199–226 GHz.     

A high-performance W-band uniplanar subharmonic mixer

A uniplanar subharmonic mixer has been implemented in coplanar waveguide (CPW) technology. The circuit is designed to operate at RF frequencies of 92-96 GHz, IF frequencies of 2-4 GHz, and LO frequencies of 45-46 GHz. Total circuit size excluding probe pads and transitions is less than 0.8 mm ×1.5 mm. The measured minimum single-sideband (SSB) conversion loss is 7.0 dB at an RF of 94 GHz, and represents state-of-the-art performance for a planar W-band subharmonic mixer. The mixer is broad-band with a SSB conversion loss of less than 10 dB over the 83-97-GHz measurement band. The measured LO-RF isolation is better than -40 dB for LO frequencies of 45-46 GHz. The double-sideband (DSB) noise temperature measured using the Y-factor method is 725 K at an LO frequency of 45.5 GHz and an IF frequency of 1.4 GHz. The measured data agrees well with the predicted performance using harmonic-balance analysis (HBA). Potential applications are millimeter-wave receivers for smart munition seekers and automotive-collision-avoidance radars     

一款集成驱动放大器的低变频损耗混频器设计

采用0.5μm GaAs工艺设计并制造了一款单片集成驱动放大器的低变频损耗混频器.电路主要包括混频部分、巴伦和驱动放大器3个模块.混频器的射频(RF)、本振(LO)频率为4～7 GHz,中频(IF)带宽为DC～2.5 GHz,芯片变频损耗小于7 dB,本振到射频隔离度大于35 dB,本振到中频隔离度大于27 dB.1 dB压缩点输入功率大于11 dBm,输入三阶交调点大于20 dBm.该混频器单片集成一款驱动放大器,解决了无源混频器要求大本振功率的问题,变频功能由串联二极管环实现,巴伦采用螺旋式结构,在实现超低变频损耗和良好隔离度的同时,保持了较小的芯片面积.整体芯片面积为1.1 mm×1.2 mm.     

A 60-GHz Phased Array Receiver Front-End in 0.13-$mu {hbox{m}}$ CMOS Technology

This paper presents a fully integrated dual-antenna phased-array RF front-end receiver architecture for 60-GHz broadband wireless applications. It contains two differential receiver chains, each receiver path consists of an on-chip balun, ag_m-boosted current-reuse low-noise amplifier (LNA), a sub-harmonic dual-gate down-conversion mixer, an IF mixer, and a baseband gain stage. An active all-pass filter is employed to adjust the phase shift of each LO signal. Associated with the proposed dual conversion topology, the phase shift of the LO signal can be scaled to one-third. Differential circuitry is adopted to achieve good common-mode rejection. The g_m-boosted current-reuse differential LNA mitigates the noise, gain, robustness, stability, and integration challenges. The sub-harmonic dual-gate down-conversion mixer prevents the third harmonic issue in LO as well. Realized in a 0.13-mum 1P8M RF CMOS technology, the chip occupies an active area of 1.1 times 1.2 mm². The measured conversion gain and input P1 dB of the single receiver path are 30 dB and -27 dBm , respectively. The measured noise figure at 100 MHz baseband output is around 10 dB. The measured phased array in the receiver achieves a total gain of 34.5 dB and theoretically improves the receiver SNR by 4.5 dB. The proposed 60 GHz receiver dissipates 44 mW from a 1.2 V supply voltage. The whole two-channel receiver, including the vector modulator circuits for built-in testing, consumes 93 mW from a 1.2 V supply voltage.     

A 400–500 GHz Balanced SIS Mixer with a Waveguide Quadrature Hybrid Coupler

We have developed a 400–500 GHz low-noise balanced SIS (Superconductor Insulator Superconductor) mixer, which is based on a waveguide RF quadrature hybrid coupler. The RF quadrature hybrid was designed and fabricated as a broadband hybrid with good performance at 4 K. The fabricated RF quadrature hybrid was measured at room temperature with a submillimeter vector network analyzer to check amplitude and phase imbalance between two output ports. Then the balanced mixer was assembled with the RF hybrid, two DSB mixers, and a 180° IF hybrid. Several important parameters such as noise temperature, LO power reduction, and IF spectra were measured. The LO power reduction is defined as how much LO power the balanced mixer saves compared with a typical single-ended mixer. The measured noise temperature of the balanced mixer was ~ 55 K at the band center which corresponds to ~ 3 times the quantum noise limit (hf/k) in DSB, and ~ 120 K at the band edges. The noise performance over LO frequency was almost the same as that of the worse DSB mixer used in the balanced mixer. In addition the LO power required for the balanced mixer is ~ 11 dB less than that of the single-ended mixers.     

0.1 THz鳍线单平衡式基波混频电路研究

研究了一种基于石英基片的0.1 THz频段的鳍线单平衡混频电路,混频电路的射频和本振信号分别从WR10标准波导端口通过波导单面鳍线微带过渡和波导微带探针过渡输入,中频信号通过本振中频双工器输出。这是一种新型的混频电路形式,与传统的W波段混频器相比,混频电路可以省略一个复杂的W波段滤波器,具有电路设计简单、安装方便的特点。该电路使用两只肖特基二极管通过倒装焊工艺粘结在厚度为75 m的石英基片上,石英基片相对传统基板,可以极大提高电路加工精度。在固定50 MHz中频信号时,射频90~110 GHz范围内,0.1 THz混频器单边带变频损耗小于9 dB。