Mechanical properties of polypropylene fibers produced from the binary polymer blends of different molecular weights

The mechanical properties of multifilament yarns, spun from the blends of a plastic‐grade polymer with a fiber‐grade CR‐polymer in the composition range of 10–50 wt % added, were investigated. The predicted modulus of a two‐phase blend, calculated from several representative equations, was compared with the elastic modulus of drawn yarns, determined from the stress vs. strain curve and dynamic modulus obtained from the sound velocity measurements. The best fit was achived with the Kleiner's simplex equation. For both the static and dynamic elastic modulus, the largest negative deviation is seen at the 80/20 and 60/40 plastic/fiber‐grade polymer blend composition, while the largest positive deviation is seen at the 90/10 plastic/fiber‐grade polymer blend composition, suggesting good compatibility of both polymers, when only a small percent of the fiber‐grade CR‐polymer is added. Improved spinnability and drawability of blended samples led to the yarns with the tensile strength over 8 cN/dtex, elastic modulus over 11 GPa and dynamic modulus over 15.5 GPa. Structural investigations have shown that the improved mechanical behavior of blended samples, compared to the yarn spun from the pure plasic‐grade polymer, is the consequence of a higher degree of crystallinity, and above all, of a much higher orientation of macromolecules. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1211–1220, 2000     

Dynamic–Mechanical Properties of Bioartificial Polymeric Materials

Bioartificial polymeric materials represent a new class of polymeric materials based on blends of synthetic and natural polymers, designed with the purpose of producing new materials with enhanced properties with respect to the single components. The mechanical properties of bioartificial materials prepared using poly(vinyl alcohol) (PVA), poly(acrylic acid) (PAA) and poly(methacrylic acid) (PMAA) as synthetic components, and collagen (SC), gelatin, starch, hyaluronic acid (HA) and dextran as biological components, were investigated by dynamic mechanical thermal analysis. The materials were prepared in the form of films or hydrogels and treated by glutaraldehyde (GTA) vapour or thermal dehydration in order to reduce their solubility in water. The results indicate that SC/PVA, gelatin/PVA and starch/PVA films behave as biphasic systems, showing good mechanical properties over a wide range of temperature. It was observed that the GTA procedure affects only the biological component of the SC/PVA and gelatin/PVA blends, whilst the thermal treatment influences mainly the synthetic polymer. In the case of HA/PVA hydrogels, a modulus variation was found with the HA content related to the organization degree and perfection of the PVA network structure. It seems evident that, in the experimental conditions used, dextran/PAA mixtures behave as miscible blends showing a glass transition intermediate between those of the pure components. With both untreated and GTA-treated gelatin/PMAA blends, it was not possible to evaluate the miscibility of the systems; it could only be affirmed that these materials show good mechanical properties over a wide range of temperature. © 1997 SCI.     

Evaluation of mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends using Taguchi experimental analysis

In this work, ternary polymer blends based on polypropylene (PP)/polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) (SEBS) triblock copolymer and a reactive maleic anhydride grafted SEBS (SEBS‐g‐MAH) at fixed compositions are prepared using twin‐screw extruder at different levels of die temperature (235‐245‐255°C), screw speed (70‐100‐130 rpm), and blending sequence (M1‐M2‐M3). In M₁ procedure, all of the components are dry blended and extruded simultaneously using Brabender twin‐screw extruder, whereas in M₂ procedure, PC, SEBS, and SEBS‐g‐MAH minor phases are first preblended in twin‐screw extruder and after granulating are added to PP continuous phase in twin‐screw extruder. Consequently, in M₃ procedure, PP and SEBS‐g‐MAH are first preblended and then are extruded with other components. The influence of these parameters as processing conditions on mechanical properties of PP/PC/SEBS ternary blends is investigated using L9 Taguchi experimental design. The responding variables are impact strength and tensile properties (Young's modulus and yield stress), which are influenced by the morphology of ternary blend, and the results are used to perform the analysis of mean effect as well. It is shown that the resulted morphology, tensile properties, and impact strength are influenced by extrusion variables. Additionally, the optimum processing conditions of ternary PP/PC/SEBS blends were achieved via Taguchi analysis. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of lignin as a filler on properties of soy protein plastics. II. Alkaline lignin

Blend plastics based on soy protein isolate (SPI) strengthened with alkaline lignin (AL) in the weight ratio of 10:0 to 5:5 were prepared with 40 wt % glycerol as a plasticizer by compression molding. The structure and mechanical properties of the blends were investigated by wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), dynamical mechanical thermal analysis (DMTA), and tensile tests. The results indicated that the introduction of AL could effectively increase the tensile strength and Young's modulus, thermal stability, and elongation of the compositive plastics when the AL content ranged from 10 to 20 parts. Moreover, the blend plastics containing 50 parts AL exhibited maximum tensile strength (1.98 MPa) and much higher than that with the SP–AL0 sheet with AL alone (0.89 MPa). In addition, tests of water absorption proved that the introduction of hydrophobic AL effectively reduced water absorption and, hence, decreased water sensibility. Therefore, AL, a relatively low‐cost filler, plays a major role in enhancing the strength and water resistivity of soy protein plastics. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3291–3297, 2003     

Mechanisms of plastic deformation in biodegradable polylactide/poly(1,4‐cis‐isoprene) blends

Polylactide (PLA), a main representative of biodegradable and made from renewable resources polymers, is surprisingly brittle at ambient temperature. In this article it is investigated how to increase its toughness by a strategy called “rubber toughening” using poly(1,4‐cis‐isoprene), a major component of natural rubber, which is immiscible with PLA, could be well dispersed in PLA matrix and is biodegradable. Immiscible blends of PLA with poly(1,4‐cis‐isoprene) were prepared by melt blending and their properties were studied and optimized. Incorporation of as low as 5 wt % of rubber increased the strain at break of compression molded film during uniaxial drawing, and also improved its tensile impact strength by 80%. The complex mechanism of plastic deformation in the blends leading to improvement of ductility and toughness was revealed. The rubbery particles initiated crazing at the early stages of deformation, as evidenced by transmission and scanning electron microscopy and also by small angle X‐ray scattering. Crazing was immediately followed by cavitation inside rubber particles, which further promoted shear yielding of PLA. The sequence of those mechanisms was proven by microscopic investigation. All three elementary mechanisms acting in the sequence indicated are responsible for surprisingly efficient toughening of PLA by a major component of natural rubber. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and thermal characteristics and morphology of polyamide 6/isotactic polypropylene blends in the presence of a β‐nucleating agent

The mechanical and thermal characteristics and morphology of polyamide 6 (PA6)/isotactic polypropylene (iPP) blends (10/90 w/w) prepared with different processing procedures and incorporated with an aryl amide nucleating agent, a kind of β‐nucleating agent (β‐NA) for iPP, were investigated. The yield strength and flexural modulus of the blends decreased as β‐NA was introduced into the blends, whereas the impact strength and elongation at break improved. The crystalline structures of the blends closely depended on (1) the processing conditions and (2) competition between the β‐nucleating effect of β‐NA and the α‐nucleating effect of PA6 for iPP. Scanning electron microscopy, differential scanning calorimetry, and X‐ray diffraction were adopted to reveal the microstructures of the blends. At a low β‐NA content (<0.1 wt %), the α‐phase iPP dominated the blends, whereas the relative content of the β‐phase iPP increased remarkably when the β‐NA content was not less than 0.1 wt %. The processing conditions also showed profound influences on the supermolecular structures of iPP; this resulted in different mechanical properties of the blends. As for PA6, the crystallization behavior and crystalline structure did not exhibit obvious changes, but PA6 did play an important role in the epitaxial crystallization of iPP on PA6. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

木质素/LDPE-EVA共混材料的力学性能及热性能

以天然热塑材料木质素和LDPE-EVA为原料,研究了不同木质素以及增容剂含量对木质素/LDPE-EVA共混材料的力学及热性能影响。结果表明,20份木质素与LDPE-EVA共混效果较好,拉伸强度达到最大（25.88 MPa）,较LDPE-EVA聚合物提高了9%,且共混物在100 ℃附近的吸热峰出现一定左移（3.6 ℃）,降解性能增加;10份增容剂LDPE-g-MAH的加入使体系拉伸强度达到35.66 MPa,较未加增容剂时提高了26.6%,100℃附近的吸热峰进一步左移（2 ℃）,降解性能小幅降低,显著提高了共混物的相容性。     

Enhanced degradation properties of polypropylene integrated with iron and cobalt stearates and its synthetic application

Synthetic plastic leads to environmental contamination, and a promising solution to this problem is to use prooxidants as fillers within them to speed up the photooxidation and thermooxidation processes. This makes plastics more susceptible to biodegradation. In this study, the degradation properties of the widely used polymer polypropylene (PP) were improved by integration with cobalt stearate (CoSt₂) and iron stearate (FeSt₃) as prooxidants with accelerating weathering degradation. The metal stearates were blended with PP in the concentration range 0.1–0.9% w/w. The properties of the blends were studied by mechanical properties testing, thermogravimetric analysis, differential scanning calorimetry, and water absorption measurement. We performed the degradation properties and thermooxidative studies by conducting an accelerated weathering test on PP–metal salt blends. Fourier transform infrared spectroscopy and scanning electron microscopy analysis of the samples before and after the accelerated weathering test were performed to study the extent of degradation in PP‐based metal salt blends. The results indicate that the tensile strength was inversely proportional to the concentration of metal stearates, and the samples showed an increased degree in polymer crystallinity (PPFe5 > PPCo5), and this led to the degradation of PP in less time. CoSt₂ predominantly enhanced the degradation of PP in comparison to FeSt₃. Food containers and pots were constructed with the tailored polymers of PP in the injection‐molding machine. Thus, metal‐stearate‐integrated polymers have great industrial potential to generate value‐added products. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46028.     

Mechanical properties,thermal, and crystallization behavior of polypropylene composites reinforced by starch and wasted cotton cloth

In this study, wasted cotton cloth was bonded with soluble starches as an adhesive, then dried, cut into fiber fragments and filled into polypropylene (PP) to achieve resource efficiency. The mechanical, thermal, and crystallization properties of the composites were characterized. The results indicated that with the addition of wasted cotton cloth treated without or with silane coupling agent (RC or TRC), PP composites' tensile strength, impact strength, and flexural strength have been improved. The heat distortion temperatures increased slowly, indicating that wasted cotton cloth filled into PP can be turned back into useful items without degradation of PP composites exhibited. Thus, it is a good avenue for the utilization of an otherwise wasted cotton cloth resource. The crystallization activation energy, nucleation constant, and folding surface free energy of PP were markedly reduced in PP/RC composites and its compatibilized composites. The value of F(T) gradually increased with the increasing relative degree of crystallinity. The addition of wasted cotton cloth could significantly reduce the spherulitic size of PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Modification of lignin–polyethylene blends with high lignin content using ethylene–vinylacetate copolymer as modifier

Blending of polyethylene with lignin in concentrations > 20 wt % yielded blends with relatively low mechanical properties. A new method, based on modification of polyethylene with ethylene–vinylacetate (EVA) copolymer, was developed for the preparation of polyethylene blends containing about 30 wt % lignin with acceptable strength properties. The addition of 10 wt % EVA caused an increase of tensile strength about twice and elongation at break about 13 times compared to those of the corresponding nonmodified samples. The optimization of lignin–polyethylene–EVA blend composition was based on a regression equation, which was obtained as output from an experimental design. The prepared composite material with 33.6 wt % lignin showed acceptable processing and mechanical properties. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1855–1860, 2004     

Mechanical properties and crystallization behavior of poly(lactic acid) blended with dendritic hyperbranched polymer

Mechanical properties of poly(lactic acid) (PLA) blended with a small amount of dendritic hyperbranched polymer (DHP) were investigated. Effects of DHP and starch on mechanical properties of PLA were compared. DHP significantly improved tensile strength and elongation at break of PLA. A small amount of starch in PLA slightly improved PLA's elongation, but had no effect on tensile strength. Isothermal crystallization kinetics of PLA blended with DHP and starch were also studied. Both DHP and starch acted as nucleation agents and significantly increased crystallization rate and crystallinity of PLA. Copyright © 2004 Society of Chemical Industry     

Blends of poly(vinyl chloride) with acrylonitrile-chlorinated polyethylene-styrene copolymer. II. Mechanical properties

Blends of poly(vinyl chloride) (PVC) and acrylonitrile-chlorinated polyethylene-styrene (ACS) graft copolymer were prepared by melt blending. Mechanical properties were studied by the use of dynamic mechanical analysis (DMA), impact tests, tensile tests, and scanning electron microscopy (SEM). The DMA study showed that PVC is immiscible with chlorinated polyethylene in ACS but partially miscible with poly(styrene-co-acrylonitrile) (25% acrylonitrile content) in ACS. Mechanical property tests showed that there is a significant increase in the impact strength while other good mechanical properties of PVC such as high modulus and high strength remain. SEM observations supported the results of the mechanical properties studies. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 399–405, 1997     

Morphological and Mechanical Properties Dependence of PLA Amount in PET Matrix Processed by Single-Screw Extrusion

In this study, the dependence on the morphology and mechanical properties was analyzed when different amounts of polylactic acid are added to the polyethylene terephthalate polymer matrix using single-screw extrusion. Thermograms of the polymer blends obtained by differential scanning calorimetry couple to thermal gravimetric analysis show a displacement in the glass transition temperature with the amount of polylactic acid (1, 2.5, 5, and 7.5 wt%) added to the polymer matrix. Scanning electron microscopy and atomic force microscopy images showed two different kinds of morphology, both characteristics of miscible and partially miscible polymer blends. Fourier transform infrared spectroscopy measurements confirmed a physical interaction by hydrogen bond in the polymer blends. The impact resistance and tensile strength are reduced with the polylactic acid addition and are influenced by the fraction of segments of hydrogen bonded in the polyethylene terephthalate/polylactic acid blends as well as their miscibility.     

Mechanical and thermal properties of polypropylene/modified basalt fabric composites

Basalt fabric (BF) was first treated with silane coupling agent KH550, modified basalt fabric (MBF) was obtained. Then MBF were molded with polypropylene (PP) matrix, and polypropylene/modified basalt fabrics (PP/MBF) composites were obtained. The influence of concentration and treating time of KH550 on MBF were characterized by hydrophilicity and lipophilicity. The tensile strength and morphology of basalt fabric were tested by single filament strength tester and scanning electron microscopy. The mechanical properties of composites were measured with electronic universal testing machine and impact testing machine, and the thermal properties were tested by thermogravimetric analysis and dynamic mechanical analysis. The results showed that the lipophilicity of MBF is improved significantly by KH550 while the tensile is nearly damaged. The mechanical properties of composites are larger than that of pure PP, among which the impact property was improved the most, showing 194.12% enhancement. The thermal stability and dynamic viscoelasticity were better than pure PP; furthermore, the concentration of KH550 virtually had no effect on the thermal stability. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42504.     

Biodegradable polymer blends: miscibility,physicochemical properties and biological response of scaffolds

This review provides an overview of synthetic biodegradable polymer blends prepared for tissue engineering applications and aims at establishing structure‐physicochemical‐biological properties relationships. The characteristics of blends consisting of semi‐crystalline/semi‐crystalline and semi‐crystalline/amorphous polymers are presented. Their biological properties such as degradability and biocompatibility and their biological performance as scaffolds in relation to cell adhesion, proliferation, infiltration, morphology and type are discussed. From available data, it can be deduced that miscibility influences physicochemical properties of the corresponding biodegradable polymeric blend scaffold, which in turn impacts on biological response. Immiscibility in polymer blends generally translates into good cell adhesion and proliferation. However, better cellular infiltration has been noted in compatible blends compared to immiscible blends. Factors such as crystallinity versus amorphous character, chirality, surface properties, degradation rate/products, mechanical properties and scaffold fabrication techniques are shown to have a major bearing on cell growth. © 2015 Society of Chemical Industry     

高分子共混物的相结构对力学性能的影响

本文以聚丙烯 尼龙1010(PP PA1010)共混体系为模型研究了高分子共混物的微观相结构对宏观力学性能的影响,并通过微观力学模型来预测共混物的拉伸强度。通过光散射试验和扫描电镜结果讨论了两相平均弦长比(L1 L2)以及分散相的质心相关距(D)与拉伸性能的关系。结果表明,当分散相一定时,拉伸强度随两相相对尺寸的增大和分散相颗粒相关性的减弱而减小。理论计算的分散相最小体积分数与相形貌观察的结果非常接近,添加增容剂的体系,由于改善了界面粘合,使理论预测值与试验结果很好的吻合。     

Blends of thermoplastic polyurethane and polypropylene. I. Mechanical and phase behavior

Pure thermoplastic polyurethane (TPU), polypropylene (PP), and TPU/PP blends with different weight ratios prepared in a twin‐screw extruder were investigated by dynamic mechanical analysis (DMA), the universal tester for mechanical investigation, and by wide‐angle X‐ray diffraction (WAXD). The addition of PP above 20 wt % to the TPU stepwise changed the ductility and Young's modulus, i.e., apparently a kind of ductile → brittle transition occurred between TPU/PP 80/20 and TPU/PP 60/40 blends. This fact and the result of analysis of WAXD curves indicated matrix → dispersed phase inversion in this concentration region. TPU melt enabled easier migration of the PP chains and prolonged crystallization of PP matrix during solidification process affecting thus crystallite size, orientation, and crystallinity. In accordance to this fact, DMA results indicated partial miscibility of PP with polyurethane in the TPU/PP blends due to the lack of interfacial interaction and adhesion between the nonpolar crystalline PP and polar TPU phases. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3980–3985, 2007     

Mechanical and thermal properties of EVA blended with biodegradable ethyl cellulose

In this study, biodegradable blend of Poly (Ethylene‐co‐Vinyl Acetate) (EVA) and Ethyl Cellulose (EC) were prepared. Ethylene vinyl alcohol (EVOH) copolymer was used as an interfacial compatibilizer to enhance adhesion between EVA and EC. The melt blended compatibilized biocomposites were examined for mechanical and thermal properties as per the ASTM standards. It has been found that the EC has a reinforcing effect on EVA leading to enhanced tensile strength and also impart biodegradability. Thus, a high loading of 50% EC could be added without compromising much on the mechanical properties. Analysis of the tensile data using predictive theories showed an enhanced interaction of the dispersed phase (EC) and the matrix (EVA). The compatibilizing effects of EVOH on these blends were confirmed by the significant improvement in the mechanical properties comparable with neat EVA as also observed by SEM microscopy. The TGA thermograms exhibits two‐stage degradation and as EC content increases, the onset temperature for thermal degradation reduces. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Compatibilization of polypropylene/polystyrene blends with poly(styrene-b-butadiene-b-styrene) block copolymer

The compatibilizing effect of the triblock copolymer poly(styrene-b-butadiene-b-styrene) (SBS) on the morphology and mechanical properties of immiscible polypropylene/polystyrene (PP/PS) blends were studied. Blends with three different weight ratios of PP and PS were prepared and three different concentrations of SBS were used for investigations of its compatibilizing effects. Scanning electron microscopy (SEM) showed that SBS reduced the diameter of the PS-dispersed particles as well as improved the adhesion between the matrix and the dispersed phase. Transmission electron microscopy (TEM) revealed that in the PP matrix dispersed particles were complex “honeycomblike” aggregates of PS particles enveloped and joined together with the SBS compatibilizer. Wide-angle X-ray diffraction (WAXD) analysis showed that the degree of crystallinity of PP/PS/SBS slightly exceeded the values given by the addition rule. At the same time, addition of SBS to pure PP and to PP/PS blends changed the orientation parameters A₁₁₀ and C significantly, indicating an obvious SBS influence on the crystallization process in the PP matrix. SBS interactions with PP and PS influenced the mechanical properties of the compatibilized PP/PS/SBS blends. Addition of SBS decreased the yield stress and the Young's modulus and improved the elongation at yield as well as the notched impact strength in comparison to the binary PP/PS blends. Some theoretical models for the determination of the Young's modulus of binary PP/PS blends were used for comparison with the experimental results. The experimental line was closest to the series model line. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 69: 2625–2639, 1998     

Mechanical and thermal properties of high‐density polyethylene toughened with glass beads

Glass beads were used to improve the mechanical and thermal properties of high‐density polyethylene (HDPE). HDPE/glass‐bead blends were prepared in a Brabender‐like apparatus, and this was followed by press molding. Static tensile measurements showed that the modulus of the HDPE/glass‐bead blends increased considerably with increasing glass‐bead content, whereas the yield stress remained roughly unchanged at first and then decreased slowly with increasing glass‐bead content. Izod impact tests at room temperature revealed that the impact strength changed very slowly with increasing glass‐bead content up to a critical value; thereafter, it increased sharply with increasing glass‐bead content. That is, the Izod impact strength of the blends underwent a sharp transition with increasing glass‐bead content. It was calculated that the critical interparticle distance for the HDPE/glass‐bead blends at room temperature (25°C) was 2.5 μm. Scanning electron microscopy observations indicated that the high impact strength of the HDPE/glass‐bead blends resulted from the deformation of the HDPE matrix. Dynamic mechanical analyses and thermogravimetric measurements implied that the heat resistance and heat stability of the blends tended to increase considerably with increasing glass‐bead content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2102–2107, 2003