Development of fatigue cracks from mechanically machined scratches on 2024‐T351 aluminium alloy—part I: experimentation and fractographic analysis

Clad and unclad 2024‐T351 aluminium alloy sheets, weakened by mechanically machined scratches, were fatigued to investigate the effect of small surface damage, like scribe marks, on aircraft fuselage joints. The role of scratch cross section geometry on fatigue life of scribed components was analysed. Scratches between 25 and 185 µm deep, with 5, 25 and 50 µm root radii, were cut on sample surface by using diamond‐tipped tools. After testing, fracture surfaces were examined using a scanning electron microscope, and crack growth rates were measured by striation counting. Scratches reduced aluminium fatigue life under tensile and bending load up to 97.8% due to multiple crack nucleation at their roots. Short cracks nucleated from sharp scratches coalesced to form unique elongated cracks growing through sample thickness. Cracks initiated from scratches were typical short cracks, growing faster than conventional long cracks. Despite the different scribing process, fatigue data of regular diamond tool cut scribes can be used to conservatively predict life reduction owing to ploughed in‐service scribe marks on fuselage joints. Finite element analyses on scribed samples and the fatigue life prediction models are described in Part II of this paper.     

Recovery of fatigue life using laser peening on 2024‐T351 aluminium sheet containing scratch damage: The role of residual stress

The aim of the current work was to study the effect of laser shock peening (LSP) when applied to 2‐mm thick 2024‐T351 aluminium samples containing scratch‐like defects in the form of V‐shaped scribes 50 to 150 μm deep. The scribes decreased fatigue life to 5% of that of the pristine material. The effect of laser peening on fatigue life was dependent on the specifics of the peen treatment, ranging from further reductions in life to restoration of the fatigue life to 61% of pristine material. Fatigue life was markedly sensitive to near‐surface tensile residual stress, even if a compressive residual stress field was present at greater depth. Fatigue life after peening was also dependent on sample distortion generated during the peening process. Sample distortion modified local stresses generated by externally applied loads, producing additional life changes. Models based on residual stress intensity and crack closure concepts were successfully applied to predict fatigue life recovery.     

Mean stress and plasticity effect prediction on notch fatigue and crack growth threshold,combining the theory of critical distances and multiaxial fatigue criteria

In the present work, we propose a robust calibration of some bi‐parametric multiaxial fatigue criteria applied in conjunction with the theory of critical distances (TCD). This is based on least‐square fitting fatigue data generated using plain and sharp‐notched specimens tested at two different load ratios and allows for the estimation of the critical distance according to the point and line method formulation of TCD. It is shown that this combination permits to incorporate the mean stress effect into the fatigue strength calculation, which is not accounted for in the classical formulation of TCD based on the range of the maximum principal stress. It is also shown that for those materials exhibiting a low fatigue‐strength‐to‐yield‐stress ratio σ_fl,R = ?1/σ_YS, such as 7075‐T6 (σ_fl,R = ?1/σ_YS = 0.30), satisfactorily accurate predictions are obtained assuming a linear‐elastic stress distribution, even at the tip of sharp notches and cracks. Conversely, for any materials characterized by higher values of this ratio, as quenched and tempered 42CrMo4 (σ_fl,R = ?1/σ_YS = 0.54), it is recommended to consider the stabilized elastic‐plastic stress/strain distribution, also for plain and blunt‐notched samples and even in the high cycle fatigue regime still with the application of the TCD.     

Investigation of cold expansion of short edge margin holes with pre‐existing cracks in 2024‐T351 aluminium alloy

The United States Air Force has requirements to inspect and cold expand potentially thousands of fastener holes for an aircraft fleet, and the presence of existing cracks at those fastener holes is expected. Fatigue experiments were performed to investigate the resulting fatigue crack growth life of a fastener hole that contained a representative ‘unknown’ crack at the time of inspection (approximately 0.050 in. in length) at a short edge margin hole that was then cold expanded and compare that to a non‐cold expanded hole and a cold expanded hole with no pre‐existing cracks. The United States Air Force analytical approach used to account for the benefit due to cold expansion was compared to the experimental data and does not consistently provide conservative predictions.     

On the mixed Mode II/III fatigue threshold behaviour for aluminium alloys 2014‐T6 and 7075‐T6

This paper describes an investigation into the fatigue threshold behaviour of two structural aluminium aerospace alloys, Al 2014‐T6 and Al 7075‐T6, when subjected to Mode II, Mode III and mixed Mode II/III loading. A unique four‐point shear loading test rig was employed to cyclically load sharply edge‐notched square bar specimens using an increasing load technique. The main aim of the work has been to generate Mode II–Mode III interaction diagrams for the fatigue threshold in each case, in order to facilitate improved design procedures for components fabricated from these alloys, which are susceptible to fatigue cracking under predominantly shear type loading. Aircraft are subjected to structural loads consisting of: pressurization, tension/compression, bending, shear and torsion, both on the ground and in flight. Representative fatigue fracture surfaces have been examined using scanning electron microscopy.