Experimental study of a high efficiency quasi-optical mode converter for whispering gallery mode gyrotrons

A mode converter for whispering gallery mode gyrotrons has been designed and experimentally demonstrated. Experiments were performed on a megawatt power level, 3μs pulsed gyrotron operating in the TE_16,2,1 whispering gallery mode at 146 GHz. The gyrotron cavity employs a non-linear uptaper to minimize radial mode conversion. About 99% of the output power is in the TE_16,2 mode. The quasi-optical converter consists of a helically cut Vlasov-type waveguide launcher and a reflector. The doubly curved reflector, designed using geometric optics and vector diffraction theory, was built to focus the full radiation pattern to a small, gaussian-like focal spot. Of the power incident in the TE_16,2 mode, 96% is directed by the launcher and reflector to a gaussian-like focal spot in the far field. Small fractions of other modes were found to form distinct focal spots in the far field. Analysis of the power in the other focal spots allows for a good quantitative measurement of gyrotron output mode content, potentially on a single shot basis.     

一种准光模式变换器的设计和实验

准光模式变换器是实现高功率回旋管高效输出的重要部件。该文针对140 GHz, TE_28,8模回旋振荡管研制,开展以Denisov型辐射器和3个准光镜面构成的准光模式变换器设计与实验研究。利用标量衍射法优化辐射器辐射口径处的场分布,其与理想高斯场之间的矢量相关性为96.2%;基于几何光学和高斯波束匹配方法设计了聚焦镜面与波束整形镜面,采用3维全波分析软件Surf3D获得各个镜面上及输出窗处的场分布,对所设计的镜面系统进行了仿真验证,在输出窗处获得了高斯模式含量为96.67%的输出波束,整个模式变换器的功率转换效率为93.98%。以自行研制的TE_28,8模激励器作为准光模式变换器的输入,通过对模式变换器转换性能仿真结果验证,在严格控制加工精度及装配和实验过程的基础上,完成了准光模式变换器转换性能的冷测实验。实验结果表明,设计和实验具有合理的一致性,可以作为准光模式变换器工程应用设计和验证手段。     

回旋管准光辐射器研究与设计

准光辐射器是高功率回旋管准光模式变换器的重要组成部分.本文首先采用几何光学理论分析圆波导准光辐射器,然后根据高斯波束(TEM00模)在辐射器切口处形成的原因,采用耦合波理论设计波纹波导准光辐射器.通过编写程序并进行数值优化完成140GHz,TE28,8模式回旋管波纹波导准光辐射器的设计,结果表明波纹波导辐射器的总长度仅为205.2mm,切口长度为47.2mm,在辐射器螺旋切口Brillouin区内高斯模式标量相关系数大于98%.本文所用的方法也可用于其它频率和模式的回旋管准光辐射器设计.     

回旋管准光辐射器研究与设计

准光辐射器是高功率回旋管准光模式变换器的重要组成部分.采用几何光学理论分析圆波导准光辐射器,根据高斯波束(TEM00模)在辐射器切口处形成的原因,利用耦合波理论设计波纹波导准光辐射器.通过编写程序并进行数值优化完成140 GHz、TE28,8模式回旋管波纹波导准光辐射器的设计,结果表明波纹波导辐射器的总长度仅为205.2 mm,切口长度为47.2 mm,在辐射器螺旋切口Brillouin区内高斯模式标量相关系数大于98%.本文所用的方法也可用于其它频率和模式的回旋管准光辐射器设计.     

Design of a Quasi-Optical Mode Converter for a Frequency Step-Tunable Gyrotron

The quasi-optical mode converter for a frequency step-tunable gyrotron which consists of a dimpled-wall antenna (Denisov-type launcher) and a beam-forming mirror system has been optimized for 9 modes from TE_17,6 at 105 GHz to TE_23,8 at 143 GHz. The first mirror is a large quasi-elliptical focusing one; the second and third are phase-correcting mirrors with a non-quadratic shape of the surface. The results of calculations show that for these modes the Denisov-type launcher has a well-focused beam with low diffraction losses, and the radiation pattern presents an almost identical field shape for all modes considered. A multi-mode optimization of the phase-correcting mirrors with two different methods has been tested. The simulations show that the phase-correcting mirrors can be used for broadband operation in the frequency range from 105 GHz up to 143 GHz in the various design modes. This quasi-optical mode converter can achieve efficiencies of 94%-98% for converting the rotating high-order cylindrical cavity modes into the usable fundamental Gaussian mode.     

A high-efficiency quasi-optical mode converter for a 140-GHz 1-MW CW gyrotron

A highly efficient quasi-optical mode converter system with several novel features has been designed and tested at Forschungszentrum Karlsruhe (FZK). The converter consists of a dimpled-wall waveguide launcher, one quasi-elliptical mirror and two toroidal mirrors. The coupled-mode theory has been used to analyze the operation of the prebunching waveguide launcher; the radiated fields from the cut of the launcher have been calculated by the scalar diffraction integral. Simulation results show that the advanced dimpled-wall launcher generates a well-focused Gaussian radiation pattern with low diffraction losses. In this case, toroidal mirrors are sufficient to obtain a desired output beam pattern. An efficiency of more than 98% has been achieved to convert the rotating TE/sub 28,8/ cavity mode at 140 GHz into a fundamental Gaussian beam. Experimental measurements show close agreement with theoretical predictions.     

Calculation of Radiation from a Helically Cut Waveguide for a Gyrotron Mode Converter in the Quasi-Optical Approximation

We present results of calculations of the radiation from a helically cut waveguide launcher, a so-called Vlasov launcher, which is commonly used either internal or external to a gyrotron for purposes of mode conversion. A gyrotron internal mode converter consists of such a launcher that radiates the waveguide mode as a nearly Gaussian beam in free space followed by a set of mirrors to focus and direct the radiation. The radiation from the launcher is first calculated using a geometric optics representation of the waveguide mode. Then the radiation is calculated in the quasi-optical limit, including diffraction. These analytic results are compared to a rigorous calculation using the computer code SURF3D, which uses an electric field integral equation (EFIE) approach. Good agreement is obtained between the quasi-optical theory and the SURF3D calculation. The present results provide new insights into the accuracy of the quasi-optical theory and may be useful for the design and improvement of Vlasov-type mode converters.     

Highly Efficient Quasi-Optical Mode Converter for a Multifrequency High-Power Gyrotron

A highly efficient quasi-optical mode converter with a bandwidth of 38 GHz has been designed and tested. The mode converter combines low-diffraction losses and a Gaussian mode content up to 97% for a set of nine modes in the range of 105 to 143 GHz for a 1-MW CW gyrotron. This was achieved using a dimpled-wall waveguide antenna (launcher), one quasi-elliptical mirror, and two toroidal mirrors. The optimization of the launcher was done using coupled-mode theory. The simulation results show a well-focused Gaussian beam for all nine operating modes. The curvature radii of the toroidal mirrors were determined by Gaussian mode transformation (ABCD-law) and subsequently optimized for a multimode operation. The simulations of the quasi-optical mode converter are based on the electric field integral equation and, thus, are 3-D. Experimental low-power measurements show close agreement with predictions.     

A High Efficiency Launcher and Mirror System for Use in a 110 GHZ TE<Subscript>22,6</Subscript> Mode Gyrotron

A four-mirror internal quasi-optical mode converter designed for a CPI gyrotron is discussed. Many improved methods were used in designing the mode converter. The launcher was designed and analyzed using the TOL and Surf3d codes developed by CCR. Mirrors 1 and 2 were designed using analytic surfaces to shape the general wavefront curvature of the beam radiated from the launcher. Mirrors 3 and 4 were iteratively designed using improved techniques that produced smooth mirror surfaces. Good agreement was found between theory and low-power cold-test measurements. The fraction of power coupled between the target Gaussian beam and the output of mirror 4, inferred from measurements, was 0.990. The stray radiation from the internal quasi-optical mode converter, inferred from measurements, was only 1.9% of the total power radiated from the launcher. This resulted in a high overall system efficiency of 97.0%, which is greater than previous designs.     

W波段准光模式变换器的设计

准光模式变换器是大功率输出回旋管的关键部件.采用高转换效率的准光模式变换器可以横向输出电磁波,增大收集极的尺寸,提高回旋管的输出功率,提高整管效率.该文设计的回旋管内置准光模式变换器由Denisov辐射器天线和四个反射镜组成,输入频率为94GHz,模式为TE_6,2模.采用耦合波理论分析和优化了Denisov辐射器内的场分布,并根据矢量绕射理论编制数值模拟程序计算了各个反射镜上的场分布,其输出功率转换效率达97.2%.利用三维全波仿真软件feko6.0进行对比分析,最后加工所设计的结构并内置于回旋振荡管进行热测实验,结果表明其输出场分布与理论计算结果基本一致.     

140 GHz回旋振荡管Denisov辐射器设计

根据几何光学和耦合波理论研究高功率回旋振荡管高阶模式在微扰圆波导中的准光传输特性,并编制出带有微扰结构辐射器准光模式变换系统的仿真程序,给出140 GHz回旋振荡管Denisov辐射器的设计方法及结果,分析其内部激励起的各模式的功率分布曲线和波导壁上的电流密度分布,得到扰动长度为60 mm,总长度为136.5 mm的Denisov辐射器结构,输出功率转换效率为99.1%,可满足140 GHz整管参数设计要求。并利用Feko软件对数值计算结果的可行性进行了有效验证,从而为热核聚变用回旋振荡管的研制打下技术基础。     

Investigation of a Broadband Quasi-Optical Mode Converter for a Multi-Frequency 1 MW Gyrotron

A broadband quasi-optical (QO) mode converter for a multi-frequency gyrotron has been designed and tested at Forschungszentrum Karlsruhe (FZK). The launcher is optimized for the TE_22,8 mode at 140 GHz, but the radiated beams present an almost identically focused pattern for all 9 considered modes between 105 GHz (TE_17,6) and 143 GHz (TE_23,8). Combining with a beam-forming mirror system, which consists of a quasi-elliptical mirror and two phase-correcting mirrors with non-quadratic surface contour, further calculations show that efficiencies of more than 94% have been achieved for converting the rotating high-order cylindrical cavity modes into the usable fundamental Gaussian mode. Low power (cold) measurements show a good agreement with theoretical predictions. This QO mode converter can be used for the broadband operation of a multi-frequency 1 MW gyrotron.     

A quasi-optical mode converter with a bifocal mirror

This paper presents the design procedure of a quasi-optical mode converter to transform any kind of TE_mn mode into a Gaussian wave beam and experimental results obtained in the particular case of the TE₆₄ mode at 110 GHz. The quasi-optical system consists of a helical-cut launcher and a bifocal mirror, which is designed, using the techniques of geometric optics, to focus the radiation of the launcher into a Gaussian focal spot. Such a system was fabricated and tested for the transformation of the TE₆₄ mode. The experimental results showed that about 80% of the power incident in the focal plane is focused into a small Gaussian-like spot of less than 20 mm diameter, while 97% of the power is contained into the main TE₆₄ lobe     

Theoretical investigation of an advanced launcher for a 2-MW 170-GHz TE/sub 34,19/ coaxial cavity gyrotron

This paper investigates the antenna waveguide (launcher), the main component of the quasi-optical mode converter of a 2-MW 170-GHz TE/sub 34,19/ coaxial cavity gyrotron, which is under development within the European Union. For coaxial gyrotrons operating in very high-order cavity modes like the TE/sub 34,19/, due to the ratio of the caustic to cavity radius of 0.323, the transformation of the high-order cavity mode into a nearly Gaussian distribution cannot be done as good as for gyrotron modes where the ratio of caustic to cavity radius is approximately 0.5. The simulation results for the TE/sub 34,19/ mode show that the average and peak values of the power density at the edges of the cuts of a conventional dimpled-wall launcher are approximately 32.3 W/cm/sup 2/ and 63.8, respectively, which will produce diffraction losses and reflection of power from the cuts. This paper reports on an advanced launcher for which average and peak values of power density of 1.9 and 5.4 W/cm/sup 2/ at the edges of the cuts are achieved, and a well-focused field at the aperture with a scalar Gaussian mode content of 94.8% is obtained.     

426GHz回旋管准光模式变换器

采用几何光学模型研究并设计了一个由Vlasov矩形开口辐射器和两级曲面反射器组成的太赫兹回旋管准光模式变换器。利用几何光学理论对Vlasov型准光模式变换器进行了初步设计,采用矢量绕射理论对准光模式变换器进行了详细的分析并编写相应程序,最后结合具体设计参数,得到工作模式在模式变换器中的变换过程。模拟结果表明,太赫兹回旋管中的TE0.6模式在输出窗处被转换为能量集中的准Gauss波束,其效率为89．0％。     

太赫兹宽带Denisov型准光模式变换器的设计分析

研究并设计了一种具有宽频带工作能力的太赫兹准光模式变换器。该准光模式变换器采用具有高效率特性的Denisov 辐射器,工作在TE_6,2模式,用于实现回旋管内的模式变换。由于Denisov 辐射器的参数是影响准光模式变换器宽带性能的主要因素,因此通过对辐射器参数的优化设计,达到增大模式变换器带宽的效果。使用自主开发的准光学模拟程序进行仿真,模式变换器中心频率为94 GHz,带宽达2 GHz。     

94 GHz回旋管准光模式变换器的数值模拟

对回旋管内置准光模式变换器进行了理论研究和数值模拟。基于几何光学理论和矢量绕射理论,编制了模拟电磁场行为的分析和优化程序,采用Vlasov辐射器和准光反射器实现了线极化准高斯模HE11。结果表明:在一级反射镜下的转换效率为88.3%,增加反射镜级数会降低转换效率。     

Quasi-optical waveguide-mode converters using a pair of phase correction mirrors

This paper describes a quasi-optical method for the conversion of modes transmitted through highly oversized circular waveguides. A waveguide-mode is radiated once from a waveguide cut in the form of a radiation beam, which is then properly shaped by two curved mirrors and directed back into the waveguide. The curved mirror shapes are iteratively and automatically determined for given propagation distances using the design technique for phase correction mirrors. The proposed method gives favorable results in designing a waveguide expander/reducer, a TE₀₁-TE₀₂ mode converter, and a TE₀₁-HE₁₁ mode converter.     

96GHz边廊模Denisov辐射器

介绍了采用Denisov辐射器将96 GHz边廊模式信号转换为高斯波束的设计、仿真及测试结果.基于耦合波理论给出Denisov辐射器的设计方法.根据96 GHz TE_(6,2)模式Denisov准光模式转换器结构布局的要求,优化得到Denisov辐射器,输入半径6.4 mm,长52 mm,辐射器切割边缘电流幅值为汇聚中心点的10%,输出准高斯能量转换效率达96.51%.由其组成的准光模式转换器冷测输出高斯波束束腰直径22.4 mm,矢量转换效率大于95%.     

W波段回旋管准光模式变换器的研究

该文对W波段TE₆₂模回旋管准光模式变换器的辐射器和镜面系统进行了设计与实验验证。基于耦合模理论,采用两级微扰对辐射器进行了设计,获得了圆波导内壁上的类高斯束斑的场分布;基于惠更斯原理的矢量衍射积分理论,对准光模式变换器的镜面系统进行了优化设计,模拟与计算结果表明准光模式变换器的模式变换效率为92.3%。最后,通过热测实验,验证了输出模式为W波段类高斯模式。