粉煤灰超疏水不锈钢网的制备及油水分离

采用树脂粘接法,将硬脂酸修饰后的粉煤灰用环氧树脂粘接在不锈钢网骨架表面,制备了超疏水不锈钢网,并对其进行了TEM、SEM、FTIR和接触角等表征。结果显示,在高倍显微镜下改性后的超疏水不锈钢网表面呈一定粗糙度的微纳米分级结构,静态水接触角高达153°。此外,该超疏水不锈钢网具有良好的机械稳定性和超疏水耐久性,其表面经机械磨损100次后水静态接触角仍高达141°。该材料用于多种油/有机溶剂与水混合液的分离中,分离效率均高于94%。     

室温下ZnO超疏水表面的制备及油水分离性能

利用简便的液相法,在室温下于不锈钢网上沉积ZnO纳米片和纳米花粗糙结构,接着通过浸渍法修饰低表面能物质硬脂酸,制备了超疏水不锈钢网。对沉积后的不锈钢网表面形貌、晶体结构、润湿性能、耐磨性能、油水分离性能等进行表征与测定。结果表明,该不锈钢网表面由纳米片和纳米花组成的微纳米结构ZnO构成,具有超疏水性,水接触角161 °;油水分离效率达98%,循环使用20次后分离效率仍保持在95.5%以上;具有良好的机械耐磨性,在高盐环境中表现出化学稳定性。     

耐腐蚀超疏水超亲油不锈钢网的制备及其在油水分离过程中的应用

以不锈钢网为基底,通过化学刻蚀法制备微米级粗糙表面,通过一步浸泡法将st9ber法制得的疏水亲油纳米Si O2颗粒沉积到粗糙的不锈钢网表面,制备了具有微纳二级粗糙结构的超疏水超亲油不锈钢网。利用扫描电子显微镜(SEM)、傅里叶变换红外光谱仪(FT-IR)和接触角测量仪(CA)表征了超疏水超亲油不锈钢网的表面形貌、化学组成和润湿性能,并将其用于油水分离过程中。结果表明,疏水亲油纳米Si O2颗粒成功的沉积到不锈钢网表面;水滴在超疏水超亲油不锈钢网上的接触角最大为151°,煤油的接触角为0°;制备的超疏水超亲油不锈钢网不仅能高效的分离不同种类油和水的混合物,还能高效的分离油和腐蚀性液体(强酸或强碱水溶液)的混合物,其耐腐蚀特性可满足复杂环境下的油水分离要求。     

室温下ZnO超疏水表面的制备及其油水分离性能

利用简便的液相法,在室温下于不锈钢网上沉积ZnO纳米片和纳米花粗糙结构,接着通过浸渍硬脂酸制备了超疏水不锈钢网.对沉积后的不锈钢网表面形貌、晶体结构、润湿性能、耐磨性能、油水分离性能等进行表征与测定.结果表明,该不锈钢网表面由纳米片和纳米花组成的微纳米结构ZnO构成,具有超疏水性,水接触角为161°;油水分离效率达98...     

类水黾脚部“凹凸沟壑”结构仿生超疏水涂层的制备与性能

以坡缕石粉为功能颜料,环氧树脂E-44和杜仲胶混合物为成膜物质,在涂有环氧/杜仲胶清漆的表面制备了一层具有类水黾脚部“凹凸沟壑”结构的仿生超疏水涂层。对涂层形貌和结构进行SEM、FTIR、XRD表征,对C3涂层（坡缕石粉质量分数为25%）进行水接触角、水滚动角、自清洁性能、抗润湿性能、耐磨性能、耐水性能等测试。结果表明,C3涂层表面具有明显的“凹凸沟壑”结构,其平均静态、动态水接触角为153.1°、152.6°,水滚动角为8.8°,具有优异的自清洁性能;C3涂层对泥土浆液、甲基橙溶液和亚甲基蓝溶液具有优良的抗润湿性,接触角均大于150°;C3涂层具有良好的基材适用性,涂覆于混凝土、织物棉布、纸张及塑料等表面均具有超疏水性能;经过载重为100 g的A4纸循环打磨50次,C3涂层水接触角依然高达151.9°,具有较好的耐磨性能;C3涂层在经过18和24 h浸泡后,其水接触角分别为152.2°和144.5°。     

喷涂法制备硅藻土/Al2O3超疏水涂层的研究

以微米级硅藻土和纳米级氧化铝粒子为原料，构筑具有一定粗糙结构的表面，以十六烷基三甲氧基硅烷（HDTMOS）为低表面能改性剂，以环氧树脂为粘接剂，制得硅藻土/Al2O3基复合超疏水涂层。首先，通过HDTMOS水解液对硅藻土和氧化铝粒子进行表面改性，再加入环氧树脂溶液获得悬浮液，采用喷涂法将上述悬浮液喷涂于基底表面，经加热固化后得到超疏水涂层。通过单因素实验筛选出最佳制备工艺（ V(HTDMOS)∶V(乙醇)=0.04∶1；m(硅藻土)∶m(Al2O3) =1.5∶0.8；m(E51)∶m(丙酮) =1∶5），其表面水静态接触角高达163.4°，扫描电镜观察其表面呈粗糙度均匀的微观分级结构。涂层适用于滤纸、木块、不锈钢板等多种基底，均可表现出优异的超疏水性能。同时，该涂层经过100次的循环磨损实验后，其表面水静态接触角仍高达146.3°。     

CNCs增强相分离法构建PVDF/PDMS超疏水表面

采用非诱导相分离法，通过将纤维素纳米晶（CNCs）与两种聚合物（聚偏二氟乙烯和聚二甲基硅氧烷）进行结合，利用CNCs之间的静电排斥力及其高比表面积特性，有效降低相分离过程中聚合物的聚集，减小了颗粒尺寸，增强了颗粒分散性，在棉布、木板和玻璃表面构造了精细均匀的微纳米粗糙结构。采用FTIR、SEM、AFM、接触角测量仪、3D光学轮廓仪对CNCs和超疏水表面的形貌、结构和超疏水性进行表征。研究发现，棉布、木板和玻璃表面的水接触角分别最高可达158 °、156.8 °和153.8 °，滚动角最低分别为2 °、2.7 °和3.4 °，呈现出明显的超疏水特征。经过机械摩擦（500余次）、酸碱处理（pH 1～13）、温度变化（–40～40°C）以及紫外光照射（0～320 h）后，基材表面仍具有较好的超疏水性。此外，基材具有优异的自清洁性和油水分离效率，超疏水棉布的最高分离效率可达98.4%。     

聚硅氧烷表面改性二氧化钛粒子及超疏水性能

为了提高二氧化钛的疏水性，解决无机二氧化钛填料在有机溶剂中的分散性、相容性等问题，采用含氟含氢乙烯基聚硅氧烷（F-PMHS）对二氧化钛粉体进行表面改性，得到具有超疏水性能的改性二氧化钛。通过FT-IR、TGA、SEM、接触角测试、沉降实验等方法研究改性后二氧化钛粒子的结构，测试其超疏水性能，分析超疏水表面形成的机理。结果表明，F-PMHS相对二氧化钛粉体质量分数仅为8%时，改性后二氧化钛粉末涂层与水的静态接触角即可达152.4°，具有良好的超疏水性能，且二氧化钛粒子在有机溶剂中的分散性与相容性得到显著提高。     

二氧化钛花状结构在木材表面的构筑及疏水性研究

为提高木材的疏水性能,通过低温水热技术路线,以三氯化钛为钛源,将二氧化钛花状结构构筑在木材表面,辅以低表面能物质硬脂酸,使木材由亲水性变为疏水性。扫描电子显微镜(SEM)和静态接触角等测试手段对处理后的木材进行了表征。结果显示,木材表面的水接触角可提高到约140°,呈现出强疏水性。     

高通量葡萄糖酸改性不锈钢网的制备及其油水分离性能研究

采用一步法将不锈钢网进行酸刻蚀并吸附葡萄糖酸(GA),成功制备了超亲水-水下超疏油的葡萄糖酸改性不锈钢网(GAG-网)。采用扫描电子显微镜、X-射线光电子能谱仪对GAG-不锈钢网表面形貌和化学组分进行表征,结果表明GA成功地吸附在了不锈钢网上和网表面成功构造微纳米粗糙结构。采用接触角测量仪对其表面进行了润湿性测试,在空气中,水滴在其表面接触角为0°;在水下,油滴在其表面接触角大于150°。GAG-网能够有效地分离多种油水混合物,分离效率均达到98%以上,分离通量达140 L·(m~2·s)~(-1);分离正己烷/水的混合物40次后仍具有99.5%以上的分离效率;在腐蚀性环境中也具有优异的分离能力。该方法简单绿色,制备过程无需任何电器和机械设备。制备的GAG-网油水分离性能优异,在处理油水混合物方面具有潜在的应用前景。     

A novel composite coating mesh film for oil-water separation

Polytetrafluoroethylene-polyphenylene sulfide composite coating mesh film was successfully prepared by a simple layered transitional spray-plasticizing method on a stainless steel mesh. It shows super-hydrophobic and super-oleophilic properties. The contact angle of this mesh film is 156.3° for water, and close to 0° for diesel oil and kerosene. The contact angle hysteresis of water on the mesh film is 4.3°. The adhesive force between the film and substrate is grade 0, the flexibility is 1 mm and the pencil hardness is 4H. An oil-water separation test was carried out for oil-contaminated water in a six-stage superhydrophobic film separator. The oil removal rate can reach about 99%.     

A robust and coarse surface mesh modified by interpenetrating polymer network hydrogel for oil‐water separation

A robust and coarse surface mesh was fabricated by introducing a hydrogel coating with interpenetrating polymer network (IPN) structure on stainless steel mesh. The IPN hydrogel was prepared by crosslinking polymerization of acrylic acid (AA) followed by condensation reaction of polyvinyl alcohol (PVA) and glutaraldehyde (GA) at room temperature. As a result, the roughness of modified mesh was enhanced obviously and oil droplet underwater showed a larger contact angle. The hydrogel‐coated surface showed an underwater superoleophobicity with an oil contact angle of 153.92 ± 1.08^°. Besides, stable wettability was observed. The mesh can selectively separate oil from water with a high separation efficiency of above 99.8%. This work provides a facile method to strengthen the coating and enhance the efficiency of oil‐water separation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41949.     

不锈钢网负载Al-beta分子筛涂层的制备及其在油水分离中的应用

使用二次生长法在不锈钢网表面制备了Al-beta分子筛涂层,并通过扫描电镜、X射线衍射和接触角检测对其进行了表征。Al-beta分子筛晶粒以球形呈现在不锈钢网表面,并相互交联而构成微纳双级粗糙结构,Al-beta涂层表现出超亲水和水中超疏油性质。将不锈钢网负载Al-beta分子筛涂层用于分离一系列油水混合物,并考察了其耐久性和稳定性。实验结果表明,不锈钢网负载Al-beta分子筛涂层在重复使用100次后其正己烷/水分离效率仍保持在97.1%以上,酸、碱和超声等处理对其形貌和油水分离效率几乎没有影响,具备优异的耐久性、自清洁性和稳定性,在实际油水分离过程中有很大应用潜力。     

One-pot fabrication of robust hydrophobia and superoleophilic cotton fabrics for effective oil-water separation

A one-pot sonochemical irradiation method was developed for the fabrication of superhydrophobic and superoleophilic cotton fabric from a solution consisting of branched silica nanoparticles and tetraethoxysilane-dodecyltrimethoxysilane sol. The silica/sol-coated cotton fabric could be wetted by liquids of low surface tension, but was water repellent with a water contact angle of 159 ± 1.2° and water shedding angle of 6 ± 0.8°. The as-prepared cotton fabric could be used as effective materials for the separation of oil from water with separation efficiency as high as 98.2% and maintained separation efficiency above 94% after 30 separation cycles for the kerosene-water mixture. Moreover, the superhydrophobic and superoleophilic cotton fabric could maintain stable superhydrophobicity after treatment with strong acidic and alkali solutions, and harsh mechanical damage. Therefore, this reported robust superhydrophobic cotton fabric exhibits encouraging practical application for oil-water separation.     

超亲水/水下超疏油膜的制备及油水分离性能

工业生产和频繁的溢油事故产生大量的含油废水,其高效分离依然面临全球性的挑战。具有仿生浸润特性的膜可以选择性透过水或油,分离效率高且操作简单而广泛应用于油水分离。本文通过一步浸渍法将TiO₂纳米颗粒和聚乙烯吡咯烷酮（PVP）原位固化到不锈钢网上制备了具有微/纳米层级结构的超亲水/水下超疏油油水分离膜。重点考察了TiO₂/PVP涂覆液浓度（质量分数1%、3%、5%、7%、9%）对膜的浸润特性和油水分离性能的影响。实验结果表明,不同TiO₂/PVP浓度改性的膜具有超亲水/水下超疏油特性,水的接触角均为0°,在水中油的接触角达160°,油水分离效率大于99.5%。膜通量随浓度的增大先减小后增加,当质量分数为3%时膜通量最大为8422.5L/（m²·h）。经过30次连续油水分离后,其分离效率仍大于99.5%,表明TiO₂/PVP-SS （stainless steel）膜有良好的耐久性和稳定性。因此,TiO₂/PVP-SS仿生特殊浸润膜材料在油水分离领域具有经济、高效、环境友好的潜在优势。     

Super-Hydrophilicity of Stainless Steel Surface Induced by Heat Treatment with Gaseous Ozone

The hydrophilic states of stainless steel surface treated by the separate or combined use of gaseous ozone and heat were investigated by measuring the contact angle of a water droplet, the content of the surface carbon contaminants, and the adsorption isotherm of water vapor. Super-hydrophilic states of stainless steel plates were achieved only by the combined gaseous ozone/heat treatment. The contact angle of a water droplet on the plate decreased from 81° to less than 5° after treating at 120 to 180 °C under 2 vol% ambient gaseous ozone. It was found that the super-hydrophilization proceeded according to two different mechanisms. One is the decomposition of surface contaminants. There was a good correlation between the surface carbon content and the water contact angle over the range of 15 to 81°. The other is the once removal of surface hydroxyl groups followed by chemisorption of water on these dehydroxylated sites. As a result of the removal of contaminants and the rehydration, the total number of surface hydroxyl groups on stainless steel became larger than that on the original surface.     

Mechanical,chemical and wetting properties of a superhydrophobic surface based on functionalized ZrO2 on stainless steel

A stable superhydrophobic FAS-ZrO₂ (FZr-ESS) surface was created by chemically etching and modifying a 304 stainless steel substrate. The effect of etching parameters such as time and temperature on the surface wetting properties was studied and optimized. The etched steel surface exhibited a honeycomb-like microstructure that, coupled with the low surface energy of the fluorinated ZrO₂ nanoparticles, produced a FZr-ESS surface with a surface contact angle (CA) of 165.9° and a sliding angle (SA) of 1.7°. The presence of highly stable functionalized ZrO₂ conjugated to the steel matrix contributed to the surface's outstanding mechanical stability, as confirmed by tape peeling and sandpaper abrasion tests. Furthermore, the FZr-ESS surface demonstrated exceptional chemical stability under a variety of pH conditions due to its excellent water repellency. An electrochemical test showed that the resulting surface was highly resistant to corrosion, with the corrosion current density reduced by nearly two orders of magnitude compared to bare stainless steel. The superhydrophobic FZr-ESS surface also displayed excellent long-term stability, wetting diversity, and self-cleaning behavior, making it highly versatile for a range of applications.     

Single-step prepared hybrid ZnO/CuO nanopowders for water repellent and corrosion resistant coatings

In this study, ZnO/CuO hybrid hydrophobic nanopowders were synthesized using a common single-step chemical precipitation route without using modifiers. Influence of initial ZnO:CuO precursor concentrations and alkaline agent type on the wettability behavior of the prepared samples were investigated. Wettability properties of the prepared samples were assessed by measuring the water contact angle and contact angle hysteresis values. Fourier transform infrared spectra, scanning electron microscope micrographs and X-ray diffraction patterns were applied to identify the surface chemistry and morphological features. Scanning electron microscope images of the synthesized ZnO/CuO nanocomposites indicated flower-like morphologies containing plenty of nano-needles, -rods, and -sheets with thicknesses lower than 90 nm. The sample prepared under the optimum conditions was superhydrophobic having water contact angle and contact angle hysteresis of 162.6°±1 and 2°, respectively. It was applied to coat the surface of stainless steel meshes by spray deposition method. The resultant superhydrophobic surface exhibited excellent self-cleaning (water repellency) property and a suitable stabilities under the ambient and saline solution (NaCl, 3.5%) media. Additionally, electrochemical corrosion tests confirmed that the corrosion resistance of the fabricated ZnO–CuO coating was higher than the initial bare mesh.