Effect of the concentration of diphenyloctyl phosphate as a flame-retarding additive on the electrochemical performance of lithium-ion batteries

We selected diphenyloctyl phosphate (DPOF) as a flame-retardant and plasticizer, and studied the influence of different amounts of the DPOF additive on the electrochemical performance of lithium-ion batteries. The electrochemical cell performances of the additive-containing electrolytes in combination with a cell comprising an LiCoO₂ cathode and mesocarbon microbeads (MCMB) anode were tested in coin cells. The cyclic voltammetry (CV) results showed that the oxidation potential of the electrolyte containing DPOF in the concentration range from 10 to 30 wt.% is about 4.75-5.5 V versus Li/Li⁺. In the present work, a DPOF content of 10 wt.% in the 1.15 M LiPF₆/EC:EMC (4:6 by vol.%) electrolyte turned out to be the optimum condition for the improvement of the electrochemical cell performance, due to the decrease of the irreversible capacity during the first cycle and decrease of the charge-transfer resistance after 40 cycles.     

Effect of vinyl acetate plus vinylene carbonate and vinyl ethylene carbonate plus biphenyl as electrolyte additives on the electrochemical performance of Li-ion batteries

For application to Li-ion batteries, we studied the electrochemical behavior and thermal stability of the following two combinations of binary electrolyte additives in a triphenylphosphate (TPP)-containing ionic electrolyte: vinyl acetate (VA) plus vinylene carbonate (VC), and vinyl ethylene carbonate (VEC) plus biphenyl (BP). Mesocarbon microbeads (MCMB) and LiCoO₂ were used as the anode and cathode materials, respectively. Cyclic voltammetry (CV), differential scanning calorimetry (DSC), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM) were used for the analyses. These results confirmed the capability of the VEC + BP electrolyte additive to improve the cell performance and electrolyte thermal stability in TPP-containing solutions in Li-ion batteries.     

Room temperature molten salts as lithium battery electrolyte

In the present study, are reported investigations obtained with the room temperature molten salt (RTMS) ethyl-methyl-imidazolium bis-(trifluoromethanesulfonyl)-imide (EMI-TFSI) in order to use it as solvent in lithium battery. The thermal stability, viscosity, conductivity and electrochemical properties are presented. A solution of 1m lithium bis-(trifluoromethanesulfonyl)-imide (LiTFSI) in EMI-TFSI has been used to test the electrolyte in a battery with LiCoO₂ and Li₄Ti₅O₁₂ as respectively cathode and anode materials. Cycling and power measurements have been obtained. The results have been compared with those obtained with a molten salt formulated with a different anion, BF₄⁻ and with a conventional liquid organic solvent EC/DMC containing LiTFSI. The 1m LiTFSI/EMI-TFSI electrolyte provides the best cycling performance: a capacity up to 106 mAh g⁻¹ is still delivered after 200 cycles, with 1C rate at 25 °C.     

Preparation of micro-dot electrodes of LiCoO2 and Li4Ti5O12 for lithium micro-batteries

Fabrications of micro-dot electrodes of LiCoO₂ and Li₄Ti₅O₁₂ on Au substrates were demonstrated using a sol-gel process combined with a micro-injection technology. A typical size of prepared dots was about 100 μm in diameter, and the dot population on the substrate was 2400 dots cm⁻². The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were characterized with scanning electron microscopy, X-ray diffraction, micro-Raman spectroscopy, and cyclic voltammetry. The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were evaluated in an organic electrolyte as cathode and anode for lithium micro-battery, respectively. The LiCoO₂ micro-dot electrode exhibited reversible electrochemical behavior in a potential range from 3.8 to 4.2 V versus Li/Li⁺, and the Li₄Ti₅O₁₂ micro-dot electrode showed sharp redox peaks at 1.5 V.     

Enhanced electrochemical performance and thermal stability of La2O3-coated LiCoO2

An enhanced electrochemical performance LiCoO₂ cathode was synthesized by coating with various wt.% of La₂O₃ to the LiCoO₂ particle surfaces by a polymeric method, followed by calcination at 923 K for 4 h in air. The surface-coated materials were characterized by XRD, TGA, SEM, TEM, BET and XPS/ESCA techniques. XRD patterns of La₂O₃-coated LiCoO₂ revealed that the coating did not affect the crystal structure, α-NaFeO₂, of the cathode material compared to pristine LiCoO₂. TEM images showed a compact coating layer on the surface of the core material that had an average thickness of about ∼15 nm. XPS data illustrated that the presence of two different environmental O 1s ions corresponds to the surface-coated La₂O₃ and core material. The electrochemical performance of the coated materials by galvanostatic cycling studies suggest that 2.0 wt.% coated La₂O₃ on LiCoO₂ improved cycle stability (284 cycles) by a factor of ∼7 times over the pristine LiCoO₂ cathode material and also demonstrated excellent cell cycle stability when charged at high voltages (4.4, 4.5 and 4.6 V). Impedance spectroscopy demonstrated that the enhanced performance of the coated materials is attributed to slower impedance growth during the charge-discharge processes. The DSC curve revealed that the exothermic peak corresponding to the release of oxygen at ∼464 K was significantly smaller for the La₂O₃-coated cathode material and recognized its high thermal stability.     

Enhancement of the Li ion transfer reaction at the LiCoO2 interface by 1,3,5-trifluorobenzene

This work presents a method of enhancing the kinetics of the interfacial reaction using 1,3,5-trifluorobenzene (TFB) which is used as an electron acceptor due to its locally biased polarity and as a source of rearranging the layer of the electrolyte around LiCoO₂ electrode, not a SEI layer source. The full cells with TFB show a decrease in irreversible capacity loss during the first charge-to-discharge process, regardless of the SEI layer formation, and also show better discharge properties even at high rate conditions. The charge transfer resistance (R_ct) of the LiCoO₂ half cell with TFB shows the smaller resistance than that of the TFB free half cell, and the activation energy calculated from the R_ct was 24.7 kJ/mol for the TFB free half cell and 19.3 kJ/mol for the half cell with TFB. In addition, the film resistance of the half cell with TFB shows higher value when the temperature is below 283 K. Since R_ct is related to the transfer resistance of the solvated Li⁺ ions on the surface of the LiCoO₂ electrode, it will help design the electrolyte to improve the transfer velocity of Li⁺ ions around the cathode electrode for high power Li ion battery.     

Atomic force microscopy studies of surface and dimensional changes in LixCoO2 crystals during lithium de-intercalation

An in situ electrochemical atomic force microscopy (EC-AFM) cell was developed to study surface and dimensional changes of individual Li_xCoO₂ crystals during lithium de-intercalation. Discrete Li₂CO₃ particles having 50-250 nm in diameter and 5-15 nm in height were observed on the surface of stoichiometric LiCoO₂ crystals and they were shown to gradually dissolve into the LiPF₆-containing electrolyte. The dimensional change of individual Li_xCoO₂ crystals along the c_hex. axis was monitored in situ during lithium de-intercalation. Evidence of surface instability or structural instability was not found in Li_xCoO₂ single crystals upon de-intercalation to 4.2 V versus Li.     

Fabrication of all-solid-state battery using Li5La3Ta2O12 ceramic electrolyte

The chemical and electrochemical properties of Li₅La₃Ta₂O₁₂ (LLTa) solid electrolyte were extensively investigated to determine its compatibility with an all-solid-state battery. A well-sintered LLTa pellet with a garnet-like structure was obtained after sintering at 1200 °C for 24 h. Li ion conductivity of the LLTa pellet was estimated to be 1.3×10⁻⁴ S cm⁻¹. The LLTa pellet was stable when in contact with lithium metal. This indicates that Li metal anode, which is the best anode material, can be applied with the LLTa system. A full cell composed of LiCoO₂/LLTa/Li configuration was constructed, and its electrochemical properties were tested. In the resulting cyclic voltammogram, a clear redox couple of LiCoO₂ was observed, implying that the all-solid-state battery with the Li metal anode was successfully operated at room temperature. The redox peaks of the battery were still observed even after one year of storage in an Ar-filled glove-box. It can be concluded that the LLTa electrolyte is a promising candidate for the all-solid-state battery because of its relatively high Li ion conductivity and good stability when in contact with Li metal anode and LiCoO₂ cathode.     

Electrochemical behavior of LiCoO2 in a saturated aqueous Li2SO4 solution

The electrochemical behavior of a commercial LiCoO₂ with spherical shape in a saturated Li₂SO₄ aqueous solution was investigated with cyclic voltammetry and electrochemical impedance spectroscopy. Three redox couples at E_SCE = 0.87/0.71, 0.95/0.90 and 1.06/1.01 V corresponding to those found at ELi/Li⁺=4.08/3.83, 4.13/4.03 and 4.21/4.14 V in organic electrolyte solutions were observed. The diffusion coefficient of lithium ions is 1.649 × 10⁻¹⁰ cm² s⁻¹, close to the value in organic electrolyte solutions. The results indicate that the intercalation and deintercalation behavior of lithium ions in the Li₂SO₄ solution is similar to that in the organic electrolyte solutions. However, due to the higher ionic conductivity of the aqueous solution, current response and reversibility of redox behavior in the aqueous solution are better than in the organic electrolyte solutions, suggesting that the aqueous solution is favorable for high rate capability. The charge transfer resistance, the exchange current and the capacitance of the double layer vary with the charge voltage during the deintercalation process. At the peak of the oxidation (0.87 V), the charge transfer resistance is the lowest. These fundamental results provide a good base for exploring new safe power sources for large scale energy storage.     

Lanthanum-doped LiCoO2 cathode with high rate capability

Lanthanum-doped LiCoO₂ composite cathode materials, containing 0.1-10 mol% of La were synthesized by citric acid aided combustion technique. Thermal analyses showed that the sharp decomposition reaction for pristine LiCoO₂ became sluggish upon addition of lanthanum. X-ray diffraction analyses of the composites revealed existence of minute quantities of lanthanum-rich perovskite phases—rhombohedral LaCoO₃ and tetragonal La₂Li_0.5Co_0.5O₄ (14/mmm), along with rhombohedral LiCoO₂. Electron microscopy showed a distinct grain growth with increasing La content. An increase of about two orders of magnitude in the electrical conductivity (1.09 × 10⁻³ S cm⁻¹) was observed for 1.0 mol% La-doped LiCoO₂. An excellent cycling performance with capacity retention by a factor of ∼10 in comparison to the pristine LiCoO₂ was observed for the composite cathode containing 5.0 mol% La, when 2032 type coin cells were cycled at 5C rate. This has been ascribed to the structural stability induced by La doping and presence of the ion-conducting phase La₂Li_0.5Co_0.5O₄ which acts as a solid electrolyte for Li⁺ ions. A negligible growth of impedance upon repeated cycling has been observed. Cyclic voltammetry showed a remarkable improvement in reversibility and stability of the La-doped electrodes. These composite cathodes might be very useful for high rate power applications.     

Performance evaluation of printed LiCoO2 cathodes with PVDF-HFP gel electrolyte for lithium ion microbatteries

In order to improve the discharge capacity in lithium ion microbatteries, a thick-film cathode was fabricated by a screen printing using LiCoO₂ pastes. The printed cathode showed a different discharge curves when the cell was tested using various (liquid, gel and solid-state) electrolytes. When a cell test was performed with organic liquid electrolyte, the maximum discharge capacity was 200 μAh cm⁻², which corresponded to approximately 133 mAh g⁻¹ when the loading weight of LiCoO₂ was calculated. An all-solid-state microbattery could be assembled using sputtered LiPON electrolyte, an evaporated Li anode, and printed LiCoO₂ cathode films without delamination or electrical problems. However, the highest discharge capacity showed a very small value (7 μAh cm⁻²). This problem could be improved using a poly(vinylidene fluoride-hexafluoro propylene) (PVDF-HFP) gel electrolyte, which enhanced the contact area and adhesion force between cathode and electrolyte. The discharge value of this cell was measured as approximately 164 μAh cm⁻² (≈110 mAh g⁻¹). As the PVDF-HFP electrolyte had a relatively soft contact property with higher ionic conductance, the cell performance was improved. In addition, the cell can be fabricated in a leakage-free process, which can resolve many safety problems. According to these results, there is a significant possibility that a film prepared using the aforementioned paste with screen printing and PVDF-HFP gel electrolyte is feasible for a microbattery.     

Electrochemical characteristics of LSCF-SDC composite cathode for intermediate temperature SOFC

A kind of composite cathode, La_0.58Sr_0.4Co_0.2Fe_0.8O_3−δ-Ce_0.8Sm_0.2O_2−δ (LSCF-SDC), was presented in this paper. The electrochemical performance of the cathode on the electrolyte of SDC and YSZ coated with a thin SDC (YSZ/SDC) layer was studied by electrochemical impedance spectroscopy (EIS) and cathodic polarization techniques for their potential utilization in the intermediate temperature solid oxide fuel cell (IT-SOFC). Also studied was the relationship between the electro-catalytic characteristics and the electrode microstructure. Results showed that the LSCF-SDC composite electrode performed better on the SDC electrolyte than on the electrolyte of YSZ/SDC. The polarization resistance, R_p, of the cathode on the SDC electrolyte was 0.23 Ω cm² at 700 °C and 0.067 Ω cm² at 750 °C, much lower than the corresponding R_p of the same cathode on the YSZ/SDC electrolyte. At 750 °C, the cathodic overpotential of the composite cathode on the SDC electrolyte was 99.7 mV at the current density of 1.0 A cm⁻².     

Stabilisation of lithiated graphite in an electrolyte based on ionic liquids: an electrochemical and scanning electron microscopy study

1-Ethyl-3-methylimidazolium-bis(trifluoromethylsulfonyl)imide (EMI-TFSI) is shown to reversibly permit lithium intercalation into standard TIMREX^® SFG44 graphite when vinylene carbonate (VC) is used in small amounts as additive. The best performance was obtained when 5% of VC was added to a 1 M solution of LiPF₆ in EMI-TFSI. Intercalation of lithium in the SFG44 graphite host was demonstrated over 100 cycles without noticeable capacity fading. The reversible charge capacity was around 350 mA h g⁻¹ and an only small irreversible capacity loss per cycle could be observed. Li₄Ti₅O₁₂ was used as counter electrode material. Scanning electron microscopy indicates the reduction of the electrolyte without graphite exfoliation in the neat electrolyte and the formation of a passivation film in the case of a VC-containing electrolyte. Other additives that were tested comprise ethylene sulphite and acrylonitrile which show also a positive effect, but a smaller one than vinylene carbonate. LiCoO₂ positive electrodes were cycled in a 1 M solution of LiPF₆ in EMI-TFSI with good charge capacity retention over more than 300 cycles, when Li₄Ti₅O₁₂ was used as counter electrode. The formation of a passivation film is proven on the LiCoO₂-electrodes, when the electrolyte contained VC, but not in the neat ionic liquid. Finally, the stable cycling of a full cell configuration is proven in this electrolyte system. An ammonium-containing ionic liquid (methyltrioctylammonium-bis(trifluoromethylsulfonyl)-imide, MTO-TFSI) is shown to permit the cycling of both, graphite and lithium cobalt oxide when VC is used as additive in small amounts, but at slightly elevated temperatures.     

Preparation and electrochemical properties of LiCoO2-LiNi0.5Mn0.5O2-Li2MnO3 solid solutions with high Mn contents

The solid solutions LiCoO₂-LiNi_1/2Mn_1/2O₂-Li₂MnO₃ with higher Mn content have been prepared by a spray drying method between 750 and 950 °C and their electrochemical performances have also been characterized. The effects of the Li content on the structure and electrochemical performance of the samples have been studied. It was found that their lattice parameters a, c and V increase with the increase in Ni content and the decrease in Co content. The solid solutions xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ with x = 0.18, 0.27 and y = 0.2 have the largest discharge capacity, which is more than 200 mAh/g in the voltages of 3.0-4.6 V. It is believed that the optimum Co content x in xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ is between 0.2 and 0.3 in the charge-discharge voltage range of 3.0-4.6 V. The solid solutions xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ with x = 0.18-0.36 and y = 0.2 have the excellent cycling performance and the capacity retention attains to almost 100% after 50 cycles. Moreover, it is found that the discharge capacity gradually increases with the increment of cycle number especially in the initial 10 cycles. XRD showed that the layered structure has been kept all the time in 20 cycles, which is perhaps the reason why the sample has the excellent cycling performance.     

A study of lithium insertion into MnO2 containing TiS2 additive a battery material in aqueous LiOH solution

The electrochemical behavior and surface characterization of manganese dioxide (MnO₂) containing titanium disulphide (TiS₂) as a cathode in aqueous lithium hydroxide (LiOH) electrolyte battery have been investigated. The electrode reaction of MnO₂ in this electrolyte is shown to be lithium insertion rather than the usual protonation. MnO₂ shows acceptable rechargeability as the battery cathode. The influence of TiS₂ (1, 3 and 5 wt%) additive on the performance of MnO₂ as a cathode has been determined. The products formed on reduction of the cathode material have been characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), fourier transform infrared spectroscopy (IR) and transmission electron microscopy (TEM). It is found that the presence of TiS₂ to ≤3 wt% improves the discharge capacity of MnO₂. However, increasing the additive content above this amount causes a decrease in its discharge capacity.     

A novel polymer electrolyte based on PMAML/PVDF-HFP blend

A gel polymer electrolyte based on the blend of poly(methyl methacrylate-co-acrylonitrile-co-lithium methacrylate) (PMAML) and poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) was prepared and characterized. The synthesized PMAML were characterized by FTIR and NMR, respectively, and the surface morphology of the PMAML and PVDF-HFP blend membrane was also observed by scanning electron microscope (SEM). The electrochemical properties of composite electrolyte membranes were studied. The ionic conductivity of the polymer electrolyte composed of 75 wt.% 1 M LiBF₄ in ethylene carbonate (EC) and dimethyl carbonate (DMC) (EC:DMC=1:1 by weight) was about 2.6×10⁻³ S cm⁻¹ at ambient temperature. The electrochemical window of the polymer electrolyte was about 4.6 V determined from the linear sweep voltammetry plot. The lithium ion polymer batteries were assembled by sandwiching gel polymer electrolyte between LiCoO₂ cathode and mesophase carbon fibre (MPCF) anode. Charge-discharge test results display that lithium ion batteries with these gel polymer electrolytes have good electrochemical performance.     

N-(triphenylphosphoranylidene) aniline as a novel electrolyte additive for high voltage LiCoO2 operations in lithium ion batteries

We report N-(triphenylphosphoranylidene) aniline (TPPA) as a new electrolyte additive for high performance lithium cobalt oxide (LiCoO₂) electrodes during high voltage operations. When cycled in the voltage range of 3.0–4.4 V, graphite-LiCoO₂ full cells with 0.2 wt% TPPA exhibited 10% increased discharge capacities after 200 cycles compared to those of control cells with no such additive. The enhanced cycling performance is attributed to the additive effect toward the modified surface films on LiCoO₂ electrodes that suppress the decomposition of both solvent and salt in the electrolyte. This additive effect was characterized by electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS).     

Amorphous LiCoO2 thin films on Li1+x+yAlxTi2−xSiyP3−yO12 prepared by radio frequency magnetron sputtering for all-solid-state Li-ion batteries

Amorphous LiCoO₂ thin films were deposited on the NASICON-type glass ceramics, Li_1+x+yAl_xTi_2−xSi_yP_3−yO₁₂ (LATSP), by radio frequency (RF) magnetron sputtering below 180 °C. The as-deposited LiCoO₂ thin films were characterized by X-ray diffraction, scanning electron microscopy and atomic force microscope. All-solid-state Li/PEO₁₈-Li (CF₃SO₂)₂N/LATSP/LiCoO₂/Au cells were fabricated using the amorphous film. The electrochemical performance of the cells was investigated by galvanostatic cycling, cyclic voltammetry, potentiostatic intermittent titration technique and electrochemical impedance spectroscopy. It was found that the amorphous LiCoO₂ thin film shows a promising electrochemical performance, making it a potential application in microbatteries for microelectronic devices.     

Effect of zwitterionic salt on the electrochemical properties of a solid polymer electrolyte with high temperature stability for lithium ion batteries

In this study, we prepare a kind of solid polymer electrolyte (SPE) based on N-ethyl-N′-methyl imidazolium tetrafluoroborate (EMIBF₄), LiBF₄ and poly(vinylidene difluoride-co-hexafluoropropylene) [P(VdF-HFP)] copolymer. The resultant SPE displays high thermal stability above 300 °C and high room temperature ionic conductivity near to 10⁻³ S cm⁻¹. Its electrochemical properties are improved with incorporation of a zwitterionic salt 1-(1-methyl-3-imidazolium)propane-3-sulfonate (MIm3S). When the SPE contains 1.0 wt% of the MIm3S, it has a high ionic conductivity of 1.57 × 10⁻³ S cm⁻¹ at room temperature, the maximum lithium ions transference number of 0.36 and the minimum apparent activation energy for ions transportation of 30.9 kJ mol⁻¹. The charge-discharge performance of a Li₄Ti₅O₁₂/SPE/LiCoO₂ cell indicates the potential application of the as-prepared SPE in lithium ion batteries.     

Synthesis of LiNi1/3Co1/3Mn1/3O2 cathode materials by using a supercritical water method in a batch reactor

LiNi_1/3Co_1/3Mn_1/3O₂ and LiCoO₂ cathode materials were synthesized by using a supercritical water (SCW) method with a metal salt solution in a batch reactor. Stoichiometric LiNi_1/3Co_1/3Mn_1/3O₂ was successfully synthesized in a 10-min reaction without calcination, while overlithiated LiCoO₂ (Li_1.15CoO₂) was synthesized using the batch SCW method. The physical properties and electrochemical performances of LiNi_1/3Co_1/3Mn_1/3O₂ were compared to those of Li_1.15CoO₂ by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and charge/discharge cycling tests. The XRD pattern of LiNi_1/3Co_1/3Mn_1/3O₂ was found to be similar to that of Li_1.15CoO₂, showing clear splitting of the (0 0 6)/(1 0 2) and (1 0 8)/(1 1 0) peak pairs as particular characteristics of the layered structure. In addition, both cathode powders showed good crystallinity and phase purity, even though a short reaction time without calcination was applied to the SCW method. The initial specific discharge capacities of the Li_1.15CoO₂ and LiNi_1/3Co_1/3Mn_1/3O₂ powders at a current density of 0.24 mA/cm² in 2.5-4.5 V were 149 and 180 mAh/g, and their irreversible capacity loss was 20 and 17 mAh/g, respectively. The discharge capacities of the Li_1.15CoO₂ and LiNi_1/3Co_1/3Mn_1/3O₂ powders decreased with cycling and remained at 108 and 154 mAh/g after 30 cycles, which are 79% and 89% of the initial capacities. Compared to the overlithiated LiCoO₂ cathode powders, the LiNi_1/3Co_1/3Mn_1/3O₂ cathode powders synthesized by SCW method had better electrochemical performances.