Influence of microstructure on the capacitive performance of polyaniline/carbon nanotube array composite electrodes

A series of polyaniline/carbon nanotube array (PANI/CNTA) composite electrodes are prepared by electrodeposition of PANI onto CNTA electrodes by 100-500 cyclic voltammetry (CV) cycles, with the aim to investigate the influence of microstructure on the capacitive performance of PANI/CNTA composites. The morphology of PANI/CNTA composites varies remarkably with the CV cycles of electrodeposition. The optimum condition is obtained for the PANI/CNTA composite prepared by 100 CV cycles, corresponding to the highest specific capacitance, best rate performance, and longest cycle life, which are much better than that of activated carbon fiber cloth, the PANI electrodeposited on stainless steel substrate, and CNTA electrode. The forming process of the microstructure and its influence on the capacitive performance of PANI/CNTA composites are presented in this paper.     

Electrochemical characterization of single-walled carbon nanotubes for electrochemical double layer capacitors using non-aqueous electrolyte

Single-walled carbon nanotubes (SWCNTs) were investigated by cyclic voltammetry and electrochemical impedance spectroscopy in a non-aqueous electrolyte, 1 M Et₄NBF₄ in acetonitrile, suitable for supercapacitors. Further, in situ dilatometry and in situ conductance measurements were performed on single electrodes and the results compared to an activated carbon, YP17. Both materials show capacitive behavior characteristic of high surface area electrodes for supercapacitors, with the maximum full cell gravimetric capacitance being 34 F/g for YP17 and 20 F/g for SWCNTs at 2.5 V with respect to the total active electrode mass. The electronic resistance of SWCNTs and activated carbon decreases significantly during charging, showing similarities of the two materials during electrochemical doping. The SWCNT electrode expands irreversibly during the first electrochemical potential sweep as verified by in situ dilatometry, indicative of at least partial debundling of the SWCNTs. A reversible periodic swelling and shrinking during cycling is observed for both materials, with the magnitude of expansion depending on the type of ions forming the double layer.     

Preparation and capacitive properties of cobalt-nickel oxides/carbon nanotube composites

In this paper, nickel-cobalt oxides/carbon nanotube (CNT) composites were prepared by adding and thermally decomposing nickel and cobalt nitrates directly onto the surface of carbon nanotube/graphite electrode to form nickel and cobalt oxides. Carbon nanotubes used in this paper were grown directly on graphite substrate by chemical vapor deposition technique. The capacitive behavior of nickel-cobalt oxides/CNT electrode was investigated by cyclic voltammetry and galvanostatic charge-discharge method in 1 M KOH aqueous solutions. The results show that nickel-cobalt oxides/CNT composite electrode has excellent charge-discharge cycle stability (0.2% and 3.6% losses of the specific capacitance are found at the 1000th and 2000th charge-discharge cycles, respectively) and good charge-discharge properties at high currrent density. Additionally, the effect of Ni/Co molar ratio on specific capacitance of the composite electrode was investigated and the highest specific capacitance (569 F g⁻¹ at 10 mA cm⁻²) is obtained at Ni/Co molar ratio = 1:1.     

Determination of the specific capacitance of conducting polymer/nanotubes composite electrodes using different cell configurations

Composite materials containing 20 wt.% of multiwalled carbon nanotubes (MWNTs) and 80 wt.% of chemically formed conducting polymers (ECP) as polyaniline (PANI) and polypyrrole (PPy) have been prepared and used for supercapacitor electrodes. The well conducting properties of MWNTs and their available mesoporosity allow a good charge propagation in the composites. Moreover, due to the good resiliency of MWNTs, an excellent stability of the supercapacitor electrodes is observed. It has been shown that the capacitance values for the composites strongly depend on the cell construction. In the case of three electrode cells, extremely high values can be found from 250 to 1100 F/g, however in the two electrode cell much smaller specific capacitance values of 190 F/g for PPy/MWNTs and 360 F/g for PANI/MWNTs have been measured. It highlights the fact that only two-electrode cells allow a good estimation of materials performance in electrochemical capacitors. The applied voltage was found to be the key factor influencing the specific capacitance of nanocomposites. For operating each electrode in its optimal potential range, asymmetric capacitors have been built with PPy/MWNTs as negative and PANI/MWNTs as positive electrodes giving capacitance values of 320 F/g per electrode material.     

Effects of the loading and polymerization temperature on the capacitive performance of polyaniline in NaNO3

Polyaniline (PANI) synthesized by a potentiostatic method at 4 °C in 1 M HNO₃ with the polymerization charge density equal to/less than 0.45 C cm⁻² was demonstrated to exhibit ideally capacitive characteristics (i.e. high reversibility and high-power property) with a high specific capacitance of 210 F g⁻¹ for the application of electrochemical supercapacitors in NaNO₃. Influences of the polymerization charge density (i.e. the polymer loading) and the polymerization temperature on the capacitive characteristics of PANI films compared by both cyclic voltammetry and charge-discharge technique were reasonably correlated with their structural properties examined by X-ray photoelectron spectroscopy (XPS). The highest specific capacitance of a PANI film polymerized at 4 °C was attributed to its lowest density of structure defects. The surface morphology of these PANI films was examined by a scanning electron microscope (SEM).     

Electrochemical behaviors of graphene-ZnO and graphene-SnO2 composite films for supercapacitors

Graphene, graphene-ZnO and graphene-SnO₂ films were successfully synthesized and used as electrode materials for electrochemical supercapacitors, respectively. The screen-printing approach was employed to fabricate graphene film on graphite substrate while the ZnO and SnO₂ were deposited on graphene films by ultrasonic spray pyrolysis. The electrochemical performances of these electrodes were comparatively analyzed through electrochemical impedance spectrometry, cyclic voltammetry and chronopotentiometry tests. The results showed that the incorporation of ZnO or SnO₂ improved the capacitive performance of graphene electrode. Graphene-ZnO composite electrode exhibited higher capacitance value (61.7 F/g) and maximum power density (4.8 kW/kg) as compared with graphene-SnO₂ and pure graphene electrodes.     

1-Methyl-3-butylimidazolium tetraflouroborate with activated carbon for electrochemical double layer supercapacitors

This article presents the main features of electrochemical double layer supercapacitors, made of nanostructured carbon materials with specially selected and optimized porosity structure and electrolyte based on solvent-free ionic liquid as follows 1-methyl-3-butylimidazolium tetrafluoroborate (1Me3BuImBF₄). The performance of supercapacitor was carried out by cyclic voltammetry and galvanostatic charge/discharge measurements. The main characteristics of stacked supercapacitors exhibit a nominal voltage 3.0 V and a maximum cell voltage 3.5 V as well as a specific capacitance (individual electrode of supercapacitor) of 111 F/g. The specific energy of 4.1 Wh/kg and specific power of 1.7 W/kg for industrial stacked supercapacitor has been achieved.     

Differential scanning calorimetry analysis of an enhanced LiNi0.8Co0.2O2 cathode with single wall carbon nanotube conductive additives

The replacement of traditional conductive carbon additives with single wall carbon nanotubes (SWCNTs) in lithium metal oxide cathode composites has been shown to enhance thermal stability as well as power capability and electrode energy density. The dispersion of 1 wt% high purity laser-produced SWCNTs in a LiNi_0.8Co_0.2O₂ electrode created an improved percolation network over an equivalent composite electrode using 4 wt% Super C65 carbon black; evidenced by additive connectivity in SEM images and an order of magnitude increase in electrode electrical conductivity. The cathode with 1 wt% SWCNT additives showed comparable active material capacity (185–188 mAh g⁻¹), at a low rate, and Coulombic efficiency to the cathode composite with 4 wt% Super C65. At increased cycling rates, the cathode with SWCNT additives had higher capacity retention with more than three times the capacity at 10C (16.4 mA cm⁻²). The thermal stability of the electrodes was evaluated by differential scanning calorimetry after charging to 4.3 V and float charging for 12 h. A 40% reduction of the cathode exothermic energy released was measured when using 1 wt% SWCNTs as the additive. Thus, the results demonstrate that replacing traditional conductive carbon additives with a lower weight loading of SWCNTs is a simple way to improve the thermal transport, safety, power, and energy characteristics of cathode composites for lithium ion batteries.     

Superior electric double layer capacitors using ordered mesoporous carbons

This paper reports for the first time superior electric double layer capacitive properties of ordered mesoporous carbon (OMCs) with varying ordered pore symmetries and mesopore structure. Compared to commercially used activated carbon electrode, Maxsorb, these OMC carbons have superior capacitive behavior, power output and high-frequency performance in EDLCs due to the unique structure of their mesopore network, which is more favorable for fast ionic transport than the pore networks in disordered microporous carbons. As evidenced by N₂ sorption, cyclic voltammetry and frequency response measurements, OMC carbons with large mesopores, and especially with 2-D pore symmetry, show superior capacitive behaviors (exhibiting a high capacitance of over 180 F/g even at very high sweep rate of 50 mV/s, as compared to much reduced capacitance of 73 F/g for Maxsorb at the same sweep rate). OMC carbons can provide much higher power density while still maintaining good energy density. OMC carbons demonstrate excellent high-frequency performances due to its higher surface area in pores larger than 3 nm. Such ordered mesoporous carbons (OMCs) offer a great potential in EDLC capacitors, particularly for applications where high power output and good high-frequency capacitive performances are required.     

Preparation and electrochemistry of NiO/SiNW nanocomposite electrodes for electrochemical capacitors

This paper studies nickel oxide/silicon nanowires (NiO/SiNWs) as composite thin films in electrodes for electrochemical capacitors. The SiNWs as backbones were first prepared by chemical etching, and then the Ni/SiNW composite structure was obtained by electroless plating of nickel onto the surface of the SiNWs. Next, the NiO/SiNW nanocomposites were fabricated by annealing Ni/SiNW composites at different temperatures in an oxygen atmosphere. Once the electrodes were constructed, the electrochemical behavior of these electrodes was investigated with cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). In 2 M KOH solution, the electrode material was found to have novel capacitive characteristics. Finally, when the NiO/SiNW composites were annealed at 400 °C, the maximum specific capacitance value was found to be as high as 681 F g⁻¹ (or 183 F cm⁻³), and the probing of the cycling life indicated that only about 3% of the capacity was lost after 1000 charge/discharge cycles. This study demonstrated that NiO/SiNW composites were the optimal electrode choice for electrochemical capacitors.     

NiO-based composite electrode with RuO2 for electrochemical capacitors

NiO/RuO₂ composite materials were prepared for use in electrochemical capacitors (ECs) by co-precipitation method followed by heat treatment. X-ray diffraction (XRD) spectra indicated that no new structural materials were formed and ruthenium oxide particles were coated by NiO particles. RuO₂ partly introduced into NiO-based electrode had improved its electrochemical performance and capacitive properties by using electrochemical measurements. A maximum specific capacitance of 210 F/g was obtained for NiO-based composite electrode with 10 wt.% RuO₂ in the voltage range from −0.4 to 0.5 V in 1 mol/l KOH solution. By comparison of effect of modified modes on the specific capacitance, chemically modified composite electrodes had more stable cycling properties than those of physically modified electrodes. After 200 cycles, specific capacitance of NiO-based chemical composite electrode with 5 wt.% RuO₂ kept 95% above, while that of physical electrode was only 79% of initial specific capacitance.     

Effects of electrochemical-deposition method and microstructure on the capacitive characteristics of nano-sized manganese oxide

The amorphous nano-structured manganese oxide was electrochemically deposited onto a stainless-steel electrode. The structure and surface morphology of the obtained manganese oxide were studied by means of X-ray diffraction analysis and scanning electron microscopy. The capacitive characteristics of the manganese oxide electrodes were investigated by means of cyclic voltammetry and constant current charge-discharge cycling. The morphological and capacitive characteristics of the hydrous manganese oxide was found to be strongly influenced by the electrochemical deposition conditions. The highest specific capacitance value of ca. 410 F g⁻¹ and the specific power of ca. 54 kW kg⁻¹ were obtained at 400 mV s⁻¹ sweep rate of potentiodynamic deposition condition. The cyclic-life data showed that the specific capacitance was highly stable up to 10,000 cycles examined. This suggests the excellent cyclic stability of the obtained amorphous hydrous manganese oxide for supercapacitor application.     

Electrochemical fabrication of polyaniline/MnO2/graphite felt as free‐standing,flexible electrode for supercapacitors

Polyaniline/MnO₂/graphite felt (PMGF) composite, which can be used as a novel free‐standing, flexible electrode for supercapacitors, was fabricated via a facile electrochemical method. Polyaniline/graphite felt (PANI/GF) electrode was prepared by electropolymerization of PANI onto the GF. Subsequently, manganese dioxide (MnO₂) was electrodeposited on the surface of the PANI/GF electrode to prepare PMGF electrode. The microstructure and morphology of the as‐prepared samples were characterized by Fourier transform infrared spectra, X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. Specific surface area was examined using N₂ adsorption/desorption test. Cyclic voltammogram, chronopotentiometry techniques and electrochemical impedance spectroscopy were introduced to investigate the electrochemical performance of the composites. The PMGF electrode exhibited specific capacitance as high as about 630 F g⁻¹ at the current density of 0.5 A g⁻¹, which is much higher than that of PANI/MnO₂ composites reported previously. The high specific capacitance of PMGF may be attributed to the fact that the porous GF is a good conductive matrix for the dispersion of PANI/MnO₂ and it can facilitate easy access of electrolytes to the electrode, which results in enhancement of the electrochemical performance of the composite. Moreover, the specific capacitance of PMGF is much larger than that of MnO₂/GF (MGF), which may be ascribed to the participant of PANI, which contributes additional pseudocapacitance and electron transport path. POLYM. COMPOS., 34:819–824, 2013. © 2013 Society of Plastics Engineers     

Electrochemical doping of single-walled carbon nanotubes in double layer capacitors studied by in situ Raman spectroscopy

The electrochemical doping of single-walled carbon nanotubes (SWCNTs) in 1 M Et₄NBF₄ in acetonitrile was investigated by in situ Raman spectroscopy. The capacitance was determined to be 82 F/g for the positive and 71 F/g for the negative SWCNT electrode, respectively, which approaches the typical values for microporous activated carbons used in supercapacitors. The changes in the Raman intensities and shifts of the D and G⁺ bands as well as of the radial breathing modes (RBMs) during electron and hole injection were studied as a function of the electrode potential. For the D and G⁺ bands, hole doping leads to strong upshifts which can be attributed to a stiffening of C-C bonds and the corresponding phonon modes. Electron doping results in much less pronounced changes in the band positions. The intensity attenuation of the RBM bands was found to be markedly different for semi-conducting and metallic SWCNTs, whereby sufficiently high doping leads to a loss of Raman intensity due to bleaching of electronic transitions. The main RBM bands upshift upon both electron and hole doping, which is attributed to changes in the chemical environment of individual SWCNTs upon charging and discharging of the electrochemical double layer within SWCNT bundles.     

Enhanced electrochemical stability and charge storage of MnO2/carbon nanotubes composite modified by polyaniline coating layer in acidic electrolytes

Manganese dioxide/multiwalled carbon nanotubes (MnO₂/MWCNTs) were synthesized by chemically depositing MnO₂ onto the surface of MWCNTs wrapped with poly(sodium-p-styrenesulfonate). Then, polyaniline (PANI) with good supercapacitive performance was further coated onto the MnO₂/MWCNTs composite to form PANI/MnO₂/MWCNTs organic-inorganic hybrid nanoarchitecture. Electrochemical performance of the hybrid in Na₂SO₄-H₂SO₄ mixed acidic electrolytes was evaluated by cyclic voltammetry (CV) and chronopotentiometry (CP) in detail. Comparative electrochemical tests revealed that the hybrid nanoarchitecture could operate in the acidic medium due to the protective modification of PANI coating layer onto the MnO₂/MWCNTs composite, and that its electrochemical behavior was greatly dependent upon the concentration of protons in the acidic electrolytes. Here, PANI not only served as a physical barrier to restrain the underlying MnO₂/MWCNTs composite from reductive-dissolution process so as to make the novel ternary hybrid material work in acidic medium to enhance the utilization of manganese oxide as much as possible, but also was another electroactive material for energy storage in the acidic mixed electrolytes. It was due to the existence of PNAI layer that an even larger specific capacitance (SC) of 384 F g⁻¹ and a much better SC retention of 79.9% over 1000 continuous charge/discharge cycles than those for the MnO₂/MWCNTs nanocomposite were delivered for the hybrid in the optimum 0.5 M Na₂SO₄-0.5 M H₂SO₄ mixed acidic electrolyte.     

Chemical anchoring of silica nanoparticles onto polyaniline chains via electro-co-polymerization of aniline and N-substituted aniline grafted on surfaces of SiO2

Chemical anchoring of silica nanoparticles onto polyaniline (PANI) chains was conducted through electro-co-polymerization of aniline and N-substituted aniline grafted on surfaces of silica nanoparticles. The grafting of N-substituted aniline on surfaces of silica nanoparticles were realized through hydrolysis of triethoxysilylmethyl N-substituted aniline (ND42) and the following condensation reaction with silanol groups on surfaces of SiO₂. Organic-inorganic interactions between PANI and SiO₂ involved in electro-co-polymerization process pushed the polymer chains apart and so facilitated the 1D growth of the polymer. Hence, the obtained hybrid film PANI/ND42-SiO₂ displayed nano-fibrous morphologies (ca. 50 nm in diameter). Consequently, PANI/ND42-SiO₂ exhibited an average specific capacitance of 380 F g⁻¹, ca. 40% higher than that of PANI/SiO₂ (276 F g⁻¹). The hybrid film also showed improved cyclic stability.     

Potentiostatically deposited polypyrrole/graphene decorated nano-manganese oxide ternary film for supercapacitors

A simple method based on potentiostatic polymerization was developed for the preparation of ternary manganese oxide-based nanocomposite films. The ternary nanocomposites, which were characterized using x-ray diffraction spectroscopy and x-ray photoelectron spectroscopy, showed that the manganese oxide within the film consisted of MnO₂ and Mn₂O₃. Electrochemical measurements showed that the ternary nanocomposite electrode exhibited high specific capacitance (up to 320.6 F/g), which was attributed to the morphology of a polypyrrole/graphene/manganese-oxide (PPy/GR/MnO_x) ternary nanocomposite. The experimental approach maximized the pseudocapacitive contribution from redox-active manganese oxide (MnO_x) and polypyrrole (PPy), as well as the electrochemical double layer capacitive (EDLC) characteristic from graphene (GR) sheets. Long cyclic measurements indicated that the specific capacitance of the ternary nanocomposite film could retain 93% of its initial value over 1000 charge/discharge cycles, in the potential range of −0.2 to 0.7 V versus silver/silver chloride electrode (Ag/AgCl).     

Supercapacitive properties of polyaniline/hydrous RuO2 composite electrode

A composite electrode based on polyaniline (PANI) and hydrous RuO₂ is prepared by electrochemical deposition of PANI onto hydrous RuO₂ (PANI/RuO₂) and its supercapacitive properties are investigated using cyclic voltammetry. The specific capacitances of PANI/RuO₂ and hydrous RuO₂ electrodes are determined to be 708 and 517 F g⁻¹ at 5 mV s⁻¹, respectively. Simple electrodeposition of PANI on the hydrous RuO₂ can achieve comparatively greater capacitance values.     

Capacitive performance of an ultralong aligned carbon nanotube electrode in an ionic liquid at 60 °C

An ultralong (1.0 mm) aligned carbon nanotube (ACNT) electrode was fabricated by a cut/paste method. The electrode retains the intrinsic properties, including robust mechanical property, high surface area, and regular pore structure, of individual nanotubes. Electrochemical properties of the ACNT electrode in an ionic liquid (IL) electrolyte were studied by cyclic voltammetry, galvanostatic charge/discharge, and ac impedance spectroscopy. The ACNT electrode achieved a specific capacitance of 27 F/g, had excellent rate capability, and a long cycle life at 60 °C, indicating that an ACNT electrode/IL electrolyte electrochemical double layer capacitor is promising for high temperature (60 °C) applications. The capacitive performance of ACNT electrode is excellent, because it possesses large pores and regular pore structures, which is revealed by N₂ adsorption and scanning electron microscopy.     

Novel chemically synthesized polyaniline electrodes containing a fluoroboric acid dopant for supercapacitors

The performance of chemically synthesized dual‐acid‐doped polyaniline (PANI) electrode material was investigated for supercapacitors for the first time. Three different grades of PANI‐containing fluoroboric acid (HBF₄) as one of the dopants were prepared by a chemical polymerization method. PANI–dodecylhydrogen sulfate–HBF₄ salt was synthesized by an emulsion polymerization pathway. A PANI–HBF₄–sodium tetrafluoroborate composite and PANI–HBF₄ salt were prepared from different modifications of dopants by a dedoping–redoping process. Capacitative behaviors of the three grades of PANI electrode materials were investigated. Among the three different grades of PANI, PANI–HBF₄ electrode showed the best performance in terms of conductivity (2.3 × 10^?1 S/cm), specific capacitance of the supercapacitor (140 F/g), specific energy (9.6 W h/kg), and specific power (58.8 W/kg). An increase in the capacitance of PANI–HBF₄ was achieved, which identified the significant contribution of the dedoping–redoping processes in the PANI system for supercapacitors. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008