Effect of adding different percentages of HfCl4 on the hydrogen storage properties of MgH2

Magnesium hydride (MgH₂) is the best candidate material to store hydrogen in the solid-state form owing to its advantages such as good reversibility, high hydrogen storage capacity (7.6 wt%), low raw material cost and abundance in the earth. Nevertheless, slow desorption/absorption kinetics and high thermodynamic stability are two issues that have constrained the commercialization of MgH₂ as a solid-state hydrogen storage material. So, to boost the desorption/absorption kinetics and to alter the thermodynamics of MgH₂, hafnium tetrachloride (HfCl₄) was used as a catalyst in this study. Different percentages of HfCl₄ (5, 10, 15 and 20 wt%) were added to MgH₂ and their catalytic influences on the hydrogen storage properties of MgH₂ were investigated. Results showed that the 15 wt% HfCl₄-doped MgH₂ sample was the best composite to enhance the hydrogen storage performance of MgH₂. The onset decomposition temperature of the 15 wt% HfCl₄-doped MgH₂ composite was decreased by ~75 °C compared to as-milled MgH₂. Meanwhile, the desorption/absorption kinetic measurements showed an improvement compared to the undoped MgH₂. From the Kissinger analysis, the apparent dehydrogenation activation energy was 167.0 kJ/mol for undoped MgH₂ and 102.0 kJ/mol for 15 wt% HfCl₄-doped MgH₂. This shows that the HfCl₄ addition reduced the activation energy of the hydrogen decomposition of MgH₂. The desorption enthalpy change calculated by the van't Hoff equation showed that the addition of HfCl₄ to MgH₂ did not affect the thermodynamic properties. Scanning electron microscopy showed that the size of the MgH₂ particles decreased and there was less agglomeration after the addition of HfCl₄. It is believed that the decrease in the particle size and in-situ generated MgCl₂ and Hf-containing species had synergistic catalytic effects on enhancing the hydrogen storage properties of the HfCl₄-doped MgH₂ composite.     

Enhanced hydrogen absorption and desorption properties of MgH2 with graphene and vanadium disulfide

Magnesium hydride (MgH₂) is the most prominent carrier for storing hydrogen in solid-state mode. However, their slow kinetics and high thermodynamics become an obstacle in hydrogen storage. The present study elaborates on the catalytic effect of graphene (Gr) and vanadium disulfide (VS₂) on MgH₂ to enhance its hydrogen sorption kinetic. The temperature-programmed desorption study shows that the onset desorption temperature of MgH₂ catalyzed by VS₂ and MgH₂ catalyzed by Gr is 289 °C and 300 °C, respectively. These desorption temperatures are 87 °C and 76 °C lower than the desorption temperature of pristine MgH₂. The rapid rehydrogenation kinetics for the MgH₂ catalyzed by VS₂ have been found at a temperature of 300 °C under 15 atm H₂ pressure by absorbing ∼4.04 wt% of hydrogen within 1 min, whereas the MgH₂ catalyzed by Gr takes ∼3 min for absorbing the same amount of hydrogen under the similar temperature and pressure conditions. The faster release of hydrogen was also observed in MgH₂ catalyzed by VS₂ than MgH₂ catalyzed by Gr and pristine MgH₂. MgH₂ catalyzed by VS₂ releases ∼2.54 wt% of hydrogen within 10 min, while MgH₂ catalyzed by Gr takes ∼30 min to release the same amount of hydrogen. Furthermore, MgH₂ catalyzed by VS₂ also persists in the excellent cyclic stability and reversibility up to 25 cycles.     

Enhanced hydrogen desorption/absorption properties of magnesium hydride with CeF3@Gn

In order to improve the hydrogen storage performance of MgH₂, graphene and CeF₃ co-catalyzed MgH₂ (hereafter denoted as MgH₂+CeF₃@Gn) were prepared by wet method ball milling and hydriding, which is a simple and time-saving method. The effect of CeF₃@Gn on the hydrogen storage behavior of MgH₂ was investigated. The experimental results showed that co-addition of CeF₃@Gn greatly decreased the hydrogen desorption/absorption temperature of MgH₂, and remarkably improved the dehydriding/hydriding kinetics of MgH₂. The onset hydrogen desorption temperature of Mg + CeF₃@Gn is 232 °C，which is 86 °C lower than that of as-milled undoped MgH₂, and its hydrogen desorption capacity reaches 6.77 wt%, which is 99% of its theoretical capacity (6.84 wt%). At 300 °C and 200 °C the maximum hydrogen desorption rates are 79.5 and 118 times faster than that of the as-milled undoped MgH₂. Even at low temperature of 150 °C, the dedydrided sample (Mg + CeF₃@Gn) also showed excellent hydrogen absorption kinetics, it can absorb 5.71 wt% hydrogen within 50 s, and its maximum hydrogen absorption rate reached 15.0 wt% H₂/min, which is 1765 times faster than that of the undoped Mg. Moreover, no eminent degradation of hydrogen storage capacity occurred after 15 hydrogen desorption/absorption cycles. Mg + CeF₃@Gn showed excellent hydrogen de/absorption kinetics because of the MgF₂ and CeH_2-3 that are formed in situ, and the synergic catalytic effect of these by-products and unique structure of Gn.     

Hydrogen absorption and desorption properties of Mg/MgH2 with nanometric dispersion of small amounts of Nb(V) ethoxide

A study to determine the optimal content of Nb(V) ethoxide required to efficiently catalyze the H₂ sorption kinetics in the Mg/MgH₂ system is reported. The materials were synthesized by hand mixing different amounts of additive (from 0.10 to 1 mol%) to pre-milled MgH₂. Considering kinetics and capacity the best performance corresponds to a 0.25 mol% of Nb ethoxide concentration. With this material, a remarkable kinetic behavior with excellent reversibility is obtained: 5.3 wt% and 5.1 wt% of hydrogen are absorbed and desorbed respectively at 300 °C in 3 min. At 250 °C the material absorbs 5.2 wt% of hydrogen and releases 3.7 wt% in 10 min. Thermal desorption starts at 247 °C and peaks at 268 °C. The H₂ sorption properties of all the materials remain unchanged after 10 cycles of absorption and desorption at 300 °C, and the best material reversibly takes in and releases 5.3 wt% of H₂ during a 10 min combined cycle. The kinetic improvement of the hydrogen desorption and absorption properties is attributed to an enhancement of the kinetic processes that occur on the surface of the material, due to the excellent spreading of the liquid additive at nanometric level, as revealed by SEM/EDS and TEM/EELS.     

Synthesis of BaFe12O19 by solid state method and its effect on hydrogen storage properties of MgH2

Previous studies have shown that ferrites give a positive effect in improving the hydrogen sorption properties of magnesium hydride (MgH₂). In this study, another ferrite, i.e., BaFe₁₂O₁₉, has been successfully synthesised via the solid state method, and it was milled with MgH₂ to enhance the sorption kinetics. The result showed that the MgH₂ + 10 wt% BaFe₁₂O₁₉ sample started to release hydrogen at about 270 °C which is about 70 °C lower than the as-milled MgH₂. The doped sample was able to absorb hydrogen for 4.3 wt% in 10 min at 150 °C, while as-milled MgH₂ only absorbed 3.5 wt% of hydrogen under similar conditions. The desorption kinetic results showed that the doped sample released about 3.5 wt% of hydrogen in 15 min at 320 °C, while the as-milled MgH₂ only released about 1.5 wt% of hydrogen. From the Kissinger plot, the apparent activation energy of the BaFe₁₂O₁₉-doped MgH₂ sample was 115 kJ/mol which was lower than the milled MgH₂ (141 kJ/mol)_. Further analyses demonstrated that MgO, Fe and Ba or Ba-containing contribute to the improvement by serving as active species, thus enhancing the MgH₂ for hydrogen storage.     

Synergistic enhancement of hydrogen storage properties in MgH2 using LiNbO3 catalyst

Extensive researches are being conducted to improve the high dehydrogenation temperature and sluggish hydrogen release rate of magnesium hydride (MgH₂) for better industrial application. In this study, LiNbO₃, a catalyst composed of alkali metal Li and transition metal Nb, was prepared through a direct one-step hydrothermal synthesis, which remarkably improved the hydrogen storage performance of MgH₂. With the addition of 6 wt% LiNbO₃ in MgH₂, the initial dehydrogenation temperature decreases from 300 °C to 228 °C, representing a drop of almost 72 °C compared to milled MgH₂. Additionally, the MgH₂-6 wt.% LiNbO₃ composite can quickly release 5.45 wt% of H₂ within 13 min at 250 °C, and absorbed about 3.5 wt% of H₂ within 30 min at 100 °C. It is also note that LiNbO₃ shows better catalytic effect compared to solely adding Li₂O or Nb₂O₅. Furthermore, the activation energy of MgH₂-6 wt.% LiNbO₃ decreased by 44.37% compared to milled MgH₂. The enhanced hydrogen storage performance of MgH₂ is attributed to the in situ formation of Nb-based oxides in the presence of LiNbO₃, which creates a multielement and multivalent chemical environment.     

Synthesis of low-cost biomass charcoal-based Ni nanocatalyst and evaluation of their kinetic enhancement of MgH2

In this study, a low-cost biomass charcoal (BC)-based nickel catalyst (Ni/BC) was introduced into the MgH₂ system by ball-milling. The study demonstrated that the Ni/BC catalyst significantly improved the hydrogen desorption and absorption kinetics of MgH₂. The MgH₂ + 10 wt% Ni/BC-3 composite starts to release hydrogen at 187.8 °C, which is 162.2 °C lower than the initial dehydrogenation temperature of pure MgH₂. Besides, 6.04 wt% dehydrogenation can be achieved within 3.5 min at 300 °C. After the dehydrogenation is completed, MgH₂ + 10 wt% Ni/BC-3 can start to absorb hydrogen even at 30 °C, which achieved the absorption of 5 wt% H₂ in 60 min under the condition of 3 MPa hydrogen pressure and 125 °C. The apparent activation energies of dehydrogenation and hydrogen absorption of MgH₂ + 10 wt% Ni/BC-3 composites were 82.49 kJ/mol and 23.87 kJ/mol lower than those of pure MgH₂, respectively, which indicated that the carbon layer wrapped around MgH₂ effectively improved the cycle stability of hydrogen storage materials. Moreover, MgH₂ + 10 wt% Ni/BC-3 can still maintain 99% hydrogen storage capacity after 20 cycles. XRD, EDS, SEM and TEM revealed that the Ni/BC catalyst evenly distributed around MgH₂ formed Mg₂Ni/Mg₂NiH₄ in situ, which act as a “hydrogen pump” to boost the diffusion of hydrogen along with the Mg/MgH₂ interface. Meanwhile, the carbon layer with fantastic conductivity enormously accelerated the electron transfer. Consequently, there is no denying that the synergistic effect extremely facilitated the hydrogen absorption and desorption kinetic performance of MgH₂.     

Interfacial engineering of nickel/vanadium based two-dimensional layered double hydroxide for solid-state hydrogen storage in MgH2

As a high-density solid-state hydrogen storage material, magnesium hydride (MgH₂) is promising for hydrogen transportation and storage. Yet, its stable thermodynamics and sluggish kinetics are unfavorable for that required for commercial application. Herein, nickel/vanadium trioxide (Ni/V₂O₃) nanoparticles with heterostructures were successfully prepared via hydrogenating the NiV-based two-dimensional layered double hydroxide (NiV-LDH). MgH₂ + 7 wt% Ni/V₂O₃ presented more superior hydrogen absorption and desorption performances than pure MgH₂ and MgH₂ + 7 wt% NiV-LDH. The initial discharging temperature of MgH₂ was significantly reduced to 190 °C after adding 7 wt% Ni/V₂O₃, which was 22 and 128 °C lower than that of 7 wt% NiV-LDH modified MgH₂ and additive-free MgH₂, respectively. The completely dehydrogenated MgH₂ + 7 wt% Ni/V₂O₃ charged 5.25 wt% H₂ in 20 min at 125 °C, while the hydrogen absorption capacity of pure MgH₂ only amounted to 4.82 wt% H₂ at a higher temperature of 200 °C for a longer time of 60 min. Moreover, compared with MgH₂ + 7 wt% NiV-LDH, MgH₂ + 7 wt% Ni/V₂O₃ shows better cycling performance. The microstructure analysis indicated the heterostructural Ni/V₂O₃ nanoparticles were uniformly distributed. Mg₂Ni/Mg₂NiH₄ and metallic V were formed in-situ during cycling, which synergistically tuned the hydrogen storage process in MgH₂. Our work presents a facile interfacial engineering method to enhance the catalytic activity by constructing a heterostructure, which may provide the mentality of designing efficient catalysts for hydrogen storage.     

The hydrogen storage properties and catalytic mechanism of the CuFe2O4-doped MgH2 composite system

The influence of CuFe₂O₄ addition on the sorption performances of MgH₂ prepared by ball milling was studied for the first time. The MgH₂ + 10 wt% CuFe₂O₄ sample exhibited an enhancement in hydrogen storage performance compared to that of as-milled MgH₂, with the onset decomposition temperature decreased from 340 °C to 250 °C. Dehydrogenation kinetic result revealed that CuFe₂O₄-added MgH₂ released around 5.3 wt% H₂ within 10 min at 320 °C, while the as-milled MgH₂ released below 1.0 wt% H₂ under the same condition. Furthermore, about 5.0 wt% H₂ was absorbed at 250 °C in 30 min for the 10 wt% CuFe₂O₄-doped MgH₂ sample. In contrast, the un-doped MgH₂ only absorbed 4.0 wt% H₂ at 250 °C in 30 min. From the Kissinger analysis, the apparent activation energy of as-milled MgH₂ was 166.0 kJ/mol and this value decreased to 113.0 kJ/mol for 10 wt% CuFe₂O₄-added MgH₂. The enhanced sorption performance of MgH₂ in the presence of CuFe₂O₄ is believed to be due to the role of in situ formed Fe, Mg-Cu alloy, and MgO phases as an active species to catalyse the hydrogen storage properties of MgH₂.     

Fast hydrogen absorption/desorption kinetics in reactive milled Mg-8 mol% Fe nanocomposites

This study aims to better understand the Fe role in the hydrogen sorption kinetics of Mg–Fe composites. Mg-8 mol% Fe nanocomposites produced by high energy reactive milling (RM) for 10 h resulted in MgH₂ mixed with free Fe and a low fraction of Mg₂FeH₆. Increasing milling time to 24 h allowed formation of a high fraction of Mg₂FeH₆ mixed with MgH₂. The hydrogen absorption/desorption behavior of the nanocomposites reactive milled for 10 and 24 h was investigated by in-situ synchrotron X-ray diffraction, thermal analyses and kinetics measurements in Sieverts-type apparatus. It was found that both 10 and 24 h milled nanocomposites presents extremely fast hydrogen absorption/desorption kinetics in relatively mild conditions, i.e., 300–350 °C under 10 bar H₂ for absorption and 0.13 bar H₂ for desorption. Nanocomposites with MgH₂, low Fe fraction and no Mg₂FeH₆ are suggested to be the most appropriate solution for hydrogen storage under the mild conditions studied.     

Enhancing hydrogen storage properties of the Mg/MgH2 system by the addition of bis(tricyclohexylphosphine)nickel(II) dichloride

This is a first report on the use of the bis(tricyclohexylphosphine)nickel (II) dichloride complex (abbreviated as NiPCy3) into MgH₂ based hydrogen storage systems. Different composites were prepared by planetary ball-milling by doping MgH₂ with (i) free tricyclohexylphosphine (PCy3) without or with nickel nanoparticles, (ii) different NiPCy3 contents (5–20 wt%) and (iii) nickel and iron nanoparticles with/without NiPCy3. The microstructural characterization of these composites before/after dehydrogenation was performed by TGA, XRD, NMR and SEM-EDX. Their hydrogen absorption/desorption kinetics were measured by TPD, DSC and PCT. All MgH₂ composites showed much better dehydrogenation properties than the pure ball-milled MgH₂. The hydrogen absorption/release kinetics of the Mg/MgH₂ system were significantly enhanced by doping with only 5 wt% of NiPCy3 (0.42 wt% Ni); the mixture desorbed H₂ starting at 220 °C and absorbed 6.2 wt% of H₂ in 5 min at 200 °C under 30 bars of hydrogen. This remarkable storage performance was not preserved upon cycling due to the complex decomposition during the dehydrogenation process. The hydrogen storage properties of NiPCy3-MgH₂ were improved and stabilized by the addition of Ni and Fe nanoparticles. The formed system released hydrogen at temperatures below 200 °C, absorbed 4 wt% of H₂ in less than 5 min at 100 °C, and presented good reversible hydriding/dehydriding cycles. A study of the different storage systems leads to the conclusion that the NiPCy3 complex acts by restricting the crystal size growth of Mg/MgH₂, catalyzing the H₂ release, and homogeneously dispersing nickel over the Mg/MgH₂ surface.     

CNTs decorated with CoFeB as a dopant to remarkably improve the dehydrogenation/rehydrogenation performance and cyclic stability of MgH2

The chain-like carbon nanotubes (CNTs) decorated with CoFeB (CoFeB/CNTs) prepared by oxidation-reduction method is introduced into MgH₂ to facilitate its hydrogen storage performance. The addition of CoFeB/CNTs enables MgH₂ to start desorbing hydrogen at only 177 °C. Whereas pure MgH₂ starts hydrogen desorption at 310 °C. The dehydrogenation apparent activation energy of MgH₂ in CoFeB/CNTs doped-MgH₂ composite is only 83.2 kJ/mol, and this is about 59.5 kJ/mol lower than that of pure MgH₂. In addition, the completely dehydrogenated MgH₂−10 wt% CoFeB/CNTs sample can start to absorb hydrogen at only 30 °C. At 150 °C and 5 MPa H₂, the MgH₂ in CoFeB/CNTs doped-MgH₂ composite can absorb 6.2 wt% H₂ in 10 min. The cycling kinetics can remain rather stable up to 20 cycles, and the hydrogen storage capacity retention rate is 98.5%. The in situ formation of Co₃MgC, Fe, CoFe and B caused by the introduction of CoFeB/CNTs can provide active and nucleation sites for the dehydrogenation/rehydrogenation reactions of MgH₂. Moreover, CNTs can provide hydrogen diffusion pathways while also enhancing the thermal conductivity of the sample. All of these can facilitate the dehydrogenation/rehydrogenation performance and cyclic stability of MgH₂.     

Thermally stable Ni MOF catalyzed MgH2 for hydrogen storage

The poor kinetics is the main issue hindering MgH₂ for practical hydrogen storage application. In this work, the tricarboxybenzene was used to construct the stable Ni MOF (Ni-BTC300) as the catalyst for MgH₂. The prepared MOFs maintained their chemical structure after 300 °C calcining and doped to MgH₂ by ball milling. The dispersed, uniformly bonded Ni atoms can improve the kinetics of the composites, which could desorb 5.14 wt% H₂ within 3 min at 300 °C. And the stable MOF structure leading to good cycle stability in both kinetics and capacity, with retention of 98.2% after 10 cycles.     

Determination of kinetic parameters and hydrogen desorption characteristics of MgH2-10 wt% (9Ni–2Mg–Y) nano-composite

Hydrogen desorption kinetic parameters of MgH₂ compounds were measured and compared with published gas solid reaction models. The compounds investigated in this study were as-received MgH₂, ball milled MgH₂, and MgH₂ ball milled with 9Ni–2Mg–Y catalyst compound. It was determined that different models were necessary to fit the hydrogen desorption data collected at different temperatures on the same sample, indicating that desorption mechanisms changed with respect to temperature. Addition of (9Ni–2Mg–Y) alloy as a catalyst to MgH₂ increased the hydrogen desorption capacity of MgH₂ from zero (for as-received MgH₂) to about 5 wt% at 350 °C within 500 s. The activation energy value was determined as 187 kJ/mol H₂ for the as-received MgH₂, 137 kJ/mol H₂ for 20 h ball milled MgH₂, and 62 kJ/mol H₂ for 20 h ball milled MgH₂-10 wt% (9Ni–2Mg–Y) nano-composite by the Arrhenius and Kissinger methods. Moreover, the integral heat of H₂ desorption for the MgH₂-10 wt% (9Ni–2Mg–Y) nano-composite was measured to be about 78 ± 0.5 kJ/mol H₂ by adsorption micro-calorimetry consistent with the results of the Arrhenius and Kissinger methods.     

Ternary transition metal alloy FeCoNi nanoparticles on graphene as new catalyst for hydrogen sorption in MgH2

The present investigation deals with the synthesis of ternary transition metal alloy nanoparticles of FeCoNi and graphene templated FeCoNi (FeCoNi@GS) by one-pot reflux method and there use as a catalyst for hydrogen sorption in MgH₂. It has been found that the MgH₂ catalyzed by FeCoNi@GS (MgH₂: FeCoNi@GS) has the onset desorption temperature of ~255 °C which is 25 °C and 100 °C lower than MgH₂ catalyzed by FeCoNi (MgH₂: FeCoNi) (onset desorption temperature 280 °C) and the ball-milled (B.M) MgH₂ (onset desorption temperature 355 °C) respectively. Also MgH₂: FeCoNi@GS shows enhanced kinetics by absorbing 6.01 wt% within just 1.65 min at 290 °C under 15 atm of hydrogen pressure. This is much-improved sorption as compared to MgH₂: FeCoNi and B.M MgH₂ for which hydrogen absorption is 4.41 wt% and 1.45 wt% respectively, under the similar condition of temperature, pressure and time. More importantly, the formation enthalpy of MgH₂: FeCoNi@GS is 58.86 kJ/mol which is 19.26 kJ/mol lower than B.M: MgH₂ (78.12 kJ/mol). Excellent cyclic stability has also been found for MgH₂: FeCoNi@GS even up to 24 cycles where it shows only negligible change from 6.26 wt% to 6.24 wt%. A feasible catalytic mechanism of FeCoNi@GS on MgH₂ has been put forward based on X-ray diffraction (XRD), Raman spectroscopy, Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Photoelectron Spectroscopy (XPS), and microstructural (electron microscopic) studies.     

Kinetic improvement of H2 absorption and desorption properties in Mg/MgH2 by using niobium ethoxide as additive

The hydrogen absorption and desorption properties of a MgH₂ – 1 mol.% Nb(V) ethoxide mixture are reported. The material was prepared by hand mixing the additive with previously ball-milled MgH₂. Nb ethoxide reacts with MgH₂ during heating, releasing C₂H₆ and H₂, and producing MgO and Nb or Nb hydride. Hydriding and dehydriding are greatly enhanced by the use of the alkoxide. At 250 °C the material with Nb takes up 1.8 wt% in 30 s compared with 0.1 wt% of pure Mg, and releases 4.2 wt% in 30 min, whereas MgH₂ without Nb does not appreciably desorb hydrogen. The absorption and desorption activation energies are reduced from 153 kJ/mol H₂ to 94 kJ/mol H₂, and from 176 kJ/mol H₂ to 75 kJ/mol H₂, respectively. The hydrogen sorption properties remain stable after 10 cycles at 300 °C. The kinetic improvement is attributed to the fine distribution of amorphous/nanometric NbH_x achieved by the dispersion of the liquid additive.     

Enhancing the dehydrogenation properties of LiAlH4 using K2NiF6 as additive

Lithium alanate (LiAlH₄) is a material that can be potentially used for solid-state hydrogen storage due to its high hydrogen content (10.5 wt%). Nevertheless, a high desorption temperature, slow desorption kinetic, and irreversibility have restricted the application of LiAlH₄ as a solid-state hydrogen storage material. Hence, to lower the decomposition temperature and to boost the dehydrogenation kinetic, in this study, we applied K₂NiF₆ as an additive to LiAlH₄. The addition of K₂NiF₆ showed an excellent improvement of the LiAlH₄ dehydrogenation properties. After adding 10 wt% K₂NiF₆, the initial decomposition temperature of LiAlH₄ within the first two dehydrogenation steps was lowered to 90 °C and 156 °C, respectively, that is 50 °C and 27 °C lower than that of the аs-milled LiAlH₄. In terms of dehydrogenation kinetics, the dehydrogenation rate of K₂NiF₆-doped LiAlH₄ sample was significantly higher as compared to аs-milled LiAlH₄. The K₂NiF₆-doped LiAlH₄ sample can release 3.07 wt% hydrogen within 90 min, while the milled LiAlH₄ merely release 0.19 wt% hydrogen during the same period. According to the Arrhenius plot, the apparent activation energies for the desorption process of K₂NiF₆-doped LiAlH₄ are 75.0 kJ/mol for the first stage and 88.0 kJ/mol for the second stage. These activation energies are lower compared to the undoped LiAlH₄. The morphology study showed that the LiAlH₄ particles become smaller and less agglomerated when K₂NiF₆ is added. The in situ formation of new phases of AlNi and LiF during the dehydrogenation process, as well as a reduction in particle size, is believed to be essential contributors in improving the LiAlH₄ dehydrogenation characteristics.     

Effects of KNbO3 catalyst on hydrogen sorption kinetics of MgH2

The influences of Nb-containing oxides and ternary compound in hydrogen sorption performance were investigated. As faster desorption kinetic and lower activation energy were reported by addition of a ternary compound catalyst such as K₂NiF₆, the influence of KNbO₃ on hydrogen storage properties of MgH₂ has been investigated for the first time. The MgH₂ - KNbO₃ composite desorbed 3.9 wt% of hydrogen within 10 min, while MgH₂ and MgH₂-Nb₂O₅ composites desorbed 0.66 wt% and 3.2 wt% respectively under similar condition. For MgH₂ with other Nb-contained catalysts such as Nb, NbO and Nb₂O₃, the desorption rate was almost the same as the one registered for as-milled MgH₂. The analysis of differential scanning calorimetry (DSC) showed that MgH₂-KNbO₃ composite started to release hydrogen at ∼335 °C which is 50 °C lower compared to as-milled MgH₂ without any additives. The activation energy for the hydrogen desorption was estimated to be about 104 ± 6.8 kJ mol⁻¹ for this material, while for the as-milled MgH₂ was about 165 ± 2.0 kJ mol⁻¹. It is believed that Nb-ternary oxide catalyst (KNbO₃) showed a good catalytic effect and enhance the sorption kinetics of MgH₂.     

Superior catalysis of NbN nanoparticles with intrinsic multiple valence on reversible hydrogen storage properties of magnesium hydride

Magnesium hydride, as a potential solid state hydrogen carrier has attracted great attention around the world especially in the energy storage domain due to the high hydrogen storage capacity and the good cycling stability. But kinetic and thermodynamic barriers also impede the practical application and development of MgH₂. Nanoscale catalysts are deemed to be the most effective measure to overcome the kinetic barrier and lower the temperature required for hydrogen release in MgH₂. NbN nanoparticles (~20 nm) with intrinsic Nb³⁺-N and Nb⁵⁺-N were prepared using the molten salt method and used as catalysts in the MgH₂ system. It is found that the NbN nanoparticles exhibit a superior catalytic effect on de/rehydrogenation kinetics for the MgH₂/Mg system. About 6.0 wt% hydrogen can be liberated for the MgH₂+5NbN sample within 5 min at 300 °C, and it takes 12 min to desorb the same amount of hydrogen at 275 °C. Meanwhile, the MgH₂+5NbN sample can absorb 6.0 wt% hydrogen within 16 min at 150 °C, and absorb 5.0 wt% hydrogen within 24 min even at 100 °C. Particularly, the catalyzed samples exhibit excellent hydrogen absorption/desorption kinetic stability. After multiple cycles, there is no kinetic attenuation and the hydrogen capacity remains at about 6.0 wt%. It is demonstrated that the NbN nanoparticles with intrinsic multiple valence can be the critical effect in improving the hydrogen storage kinetics of MgH₂. The stability of Nb₄N₃ phase and Nb³⁺-N and Nb⁵⁺-N valence states can ensure a stable catalytic effect in the system.     

Facile synthesized Fe nanosheets as superior active catalyst for hydrogen storage in MgH2

Reversible hydrogen storage in MgH₂ under mild conditions is a promising way for the realization of “Hydrogen Economy”, in which the development of cheap and highly efficient catalysts is the major challenge. Herein, A two-dimensional layered Fe is prepared via a facile wet-chemical ball milling method and has been confirmed to greatly enhance the hydrogen storage performance of MgH₂. Minor addition of 5 wt% Fe nanosheets to MgH₂ decreases the onset desorption temperature to 182.1 °C and enables a quick release of 5.44 wt% H₂ within 10 min at 300 °C. Besides, the dehydrogenated sample takes up 6 wt% H₂ in 10 min under a hydrogen pressure of 3.2 MPa at 200 °C. With the doping of Fe nanosheets, the apparent activation energy of the dehydrogenation reaction for MgH₂ is reduced to 40.7 ± 1.0 kJ mol⁻¹. Further ab initio calculations reveal that the presence of Fe extends the Mg–H bond length and reduces its bond strength. We believe that this work would shed light on designing plain metal for catalysis in the area of hydrogen storage and other energy-related issues.