Metal nanoparticles supported on polyacrylamide water beads as catalyst for efficient generation of H2 from NaBH4 methanolysis

Water beads made from polyacrylamide polymer p-(AAm) were decorated with high efficient metal nanoparticles by inexpensive, fast, simple, and environmental friendly method. These water beads balls were kept in the metal salt solutions for 4 h; to adsorb the metals ions from these aqueous solutions. The metal ions decorated on the p-(AAm) water beads were converted to metal nanoparticles by its reduction with aqueous solution of NaBH₄. The prepared materials p-(AAm) loaded with MNPs (M@p-(AAm)) were characterized by ATR-FTIR, XRD, XPS, FESEM, and EDS which show the successful preparation of MNPs over the surface and within p-(AAm). Afterwards the M@p-(AAm) were investigated as a catalyst for the generation of hydrogen from the methanolysis of NaBH₄. The Ag@p-(AAm) show good catalytic activity for NaBH₄ methanolysis reaction as compared to the other loaded MNPs. In addition, different parameters which effecting H₂ generation were also investigated such as; MNPs types, catalyst amount and temperature of the reaction. Low activation energy (Ea) of 21.37 ± 0.67 kJ mol⁻¹, was calculated for NaBH₄ methanolysis reaction at temperature ranging from 5.0 °C to 35 °C. Moreover, the catalyst reusability was also studied and found no decrease in percent conversion, however percent efficiency was decreases about 37% after completion of four cycles.     

Magnetic dendritic KCC-1 nanosphere-supported cobalt composite as a separable catalyst for hydrogen generation from NaBH4 hydrolysis

The introduction of magnetism into a catalyst can greatly optimize its separation performance. In the present work, a kind of magnetically separable catalysts for promoting NaBH₄ hydrolysis have been fabricated by anchoring cobalt nanoparticles on magnetic dendritic KCC-1 nanospheres composed of magnetic Fe₃O₄ core and fibrous shell. The fabricated catalysts were characterized with various characterization methods, including absorption spectroscopy (AAS), scanning electron microscopy (SEM), high-resolution transmission electronic microscopy (HRTEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometry (VSM), and Fourier transform infrared (FT-IR), etc. This kind of catalysts exhibit high catalytic activity for promoting the hydrolysis of NaBH₄ under alkaline conditions, giving a hydrogen generation rate and activation energy of 3.83 L min⁻¹ g_Co⁻¹ (30 °C) and 53.63 kJ mol⁻¹, respectively. After used for 5 cycles, the catalyst showed 36.5% catalytic activity reserved. Most importantly, the magnetism of the catalyst made it easily separated and recycled from the solution after the reaction completed. The development of this kind of catalysts could provide a promising option for catalyzing NaBH₄ hydrolysis for portable hydrogen production from.     

Co-P nanoparticles supported on dandelion-like CNTs-Ni foam composite carrier as a novel catalyst for hydrogen generation from NaBH4 methanolysis

We used the chemical vapor deposition method to prepare dandelion-like CNTs-Ni foam composite carrier, and then the electroless plating method was used to deposit Co-P nanoparticles on the CNTs of the CNTs-Ni foam. The CNTs-Ni foam and Co-P/CNTs-Ni foam were characterized by BET, SEM, XRD, XPS, and EDS. The results showed that CNTs were uniformly and densely grown in situ on the surface of Ni foam and were further successfully coated with Co-P nanoparticles. The Co-P/CNTs-Ni foam catalysts still maintained the dandelion-like structure and reached a maximum hydrogen production rate of 2430 mL min⁻¹ g⁻¹ at 25 °C. Furthermore, the Co-P/CNTs-Ni foam catalysts also exhibit a remarkable cycling performance and low activation energy (49.94 kJ mol⁻¹) for the methanolysis of sodium borohydride.     

CeO2 supported multimetallic nano materials as an efficient catalyst for hydrogen generation from the hydrolysis of NaBH4

Nowadays, there is still no suitable method to store large amounts of energy. Hydrogen can be stored physically in carbon nanotubes or chemically in the form of hydride. In this study, sodium borohydride (NaBH₄) was used as the source of hydrogen. However, an inexpensive and useful catalyst (Co–Cr–B/CeO₂) was synthesized using the NaBH₄ reduction method and its property was characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), x-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) measurements. The optimized Co–Cr–B/CeO₂ catalyst exhibited an excellent hydrogen generation rate (9182 mLg_metal⁻¹min⁻¹) and low activation energy (35.52 kJ mol⁻¹). The strong catalytic performance of the Co–Cr–B/CeO₂ catalyst is thought to be based on the synergistic effect between multimetallic nanoparticles and the effective charge transfer interactions between the metal and the support material.     

Poly(acrylic acid)-modified silica nanoparticles as a nonmetal catalyst for NaBH4 methanolysis

In the present work, a SiO₂@PAA catalyst for NaBH₄ methanolysis composed of silica nanoparticles modified with poly(acrylic acid) has been developed. The morphology and composition of the prepared SiO₂@PAA catalyst were analyzed with transmission electron microscopy, Fourier transform-infrared spectroscopy, x-ray photoelectron spectroscopy and thermogravimetric analysis. This catalyst showed excellent catalytic performance for methanolysis of NaBH₄. The NaBH₄ methanolysis reaction catalyzed by SiO₂@PAA showed an average hydrogen generation rate 5.5 times as high as the reaction catalyzed by unmodified SiO₂ and 10.6 times as high as the uncatalyzed reaction, respectively. The activation energy for methanolysis of NaBH₄ catalyzed by this SiO₂@PAA catalyst was 24.03 kJ/mol. Moreover, although the catalytic activity of SiO₂@PAA catalyst partially lost after being used, it could be restored after being regenerated by washing with diluted hydrochloric acid solution.     

A novel cost-effective catalyst from orange peel waste protonated with phosphoric acid for hydrogen generation from methanolysis of NaBH4

In this study, orange peel (OP), one of the organic wastes, was first used as a metal-free catalyst for the production of hydrogen from sodium boron hydride (NaBH₄). In order to prepare an orange peel catalyst (OP–H₃PO₄-Cat) with the best catalytic activity, experiments were carried out on pure orange peel with different acid types, different burning temperatures and different burning times. As a result of these experiments, it was determined that OP-H₃PO₄-Cat treated with 30% H₃PO₄ and burned at 400 °C for 45 min had the best catalytic activity. The OP-H₃PO₄-Cat material was characterised by several techniques such as FTIR, XRD and SEM. As a result, the hydrogen generation rates (HGR) at 30 °C and 60 °C in the methanolysis reaction of 2.5% NaBH₄ catalysed by OP-H₃PO₄-Cat were found as 45,244 and 61,892 mLmin^?1g.cat^?1, respectively. The activation energy of OP-H₃PO₄-Cat catalyst was calculated as 12.47 kJmol^-1.     

Research progress on catalysts for hydrogen generation through sodium borohydride alcoholysis

Hydrogen is a promising energy carrier for realizing the transition from fossil fuels to renewable energy sources. Nowadays, the development of the hydrogen economy faces many challenges connected with its efficient production, storage, distribution, and end-use. During the past decade, the alcoholysis, particularly methanolysis, of sodium borohydride (NaBH₄) has attracted much attention due to the nonflammability, nontoxicity, potential for utilization in cold conditions of the reaction system. Highly efficient catalysts are of great significance to guarantee the efficiency of the reaction and control the hydrogen release. In this review, we summarize recent advances in both metallic and nonmetallic catalysts for the alcoholysis of NaBH₄. This review also summarizes the advantages and disadvantages of various catalysts in the investigations to assess the potential opportunities and challenges for their application in NaBH₄ methanolysis. The catalytic mechanisms related to NaBH₄ methanolysis were also discussed.     

Hydrogen generation from solid state NaBH4 by using FeCl3 catalyst for portable proton exchange membrane fuel cell applications

Being a boron-based compound, sodium borohydride, NaBH₄, is a convenient hydrogen storage material for applications like unmanned air vehicles. There are several concerns behind commercialization of hydrogen gas generator by NaBH₄ hydrolysis systems. This study aims to contribute to the solution of the problems of NaBH₄ hydrolysis system in three main ways. First, the usage of solid state NaBH₄ enables to increase the durability and the gravimetric H₂ storage capacity of the system in order to meet US DOE targets. Second, solid NaBH₄ usage decreases the system's weight since it does not require a separate fuel storage tank, which is very important for portable, on demand applications. Finally, the system's cost is decreased by using an accessible and effective non-precious catalyst such as ferric chloride, FeCl₃. The maximum hydrogen generation rate obtained was 2.6 L/min and the yield was 2 L H₂/g NaBH₄ with an efficiency of 76% at its most promising condition. Moreover, the novel solid NaBH₄ hydrogen gas generator developed in the present work was integrated into a proton exchange membrane fuel cell and tested at the optimum operating conditions.     

A study on hydrogen generation from NaBH4 solution using Co-loaded resin catalysts

Hydrogen production via chemical processes has gained great attention in recent years. In this study, Co-based complex catalyst obtained by adsorption of Co metal to Amberlite IRC-748 resin and Diaion CR11 were tested for hydrogen production from alkaline NaBH₄ via hydrolysis process. Their catalytic activity and microstructure were investigated. Process parameters affecting the catalytic activity, such as NaOH concentration, Co percentage and catalyst amount, as well as NaBH₄ concentration and temperature were investigated. Furthermore, characteristics of these catalysts were carried out via SEM, XRD and FT-IR analysis. Hydrogen production rates equal to 211 and 221 ml min⁻¹ g_cat⁻¹ could be obtained with Amberlite IRC-748 resin and Diaion CR11 Co based complex catalysts, respectively. The activation energies of the catalytic hydrolysis reaction of NaBH₄ were calculated as 46.9 and 59.42 kJ mol⁻¹ for Amberlite IRC-748 resin and Diaion CR11 based catalysts respectively kJ mol⁻¹ from the system consisting of 3% Co, 10 wt% NaBH₄ and 7 wt% NaOH as well as 50 mg catalyst dosage. It can be concluded that Co-based resins as catalysts for hydrogen production is an effective alternative to other catalysts having higher rate.     

Poly (acrylic acid)/polysaccharides IPN derived metal free catalyst for rapid hydrogen generation via NaBH4 methanolysis

Polymeric catalysts have displayed great performance for catalytic hydrogen generation. However, the reported metal free polymeric catalysts for NaBH₄ methanolysis are mainly limited to coating strategy where the catalytic activity fade after few cycles. Herein, we report an interpenetrating polymer network (IPN) strategy for rapid and highly recyclable NaBH₄ catalytic methanolysis to produce hydrogen (H₂) gas. In this study, we prepared poly(acrylic acid)/polysaccharide IPN via Pickering tempted polymerization. The hydrogen generation performance was studied employing different parameters where maximum HGR of 8182 mL H₂ min^?1 g^?1 of CAP. The activation energy Ea, enthalpy and entropy were calculated to be 62.99 kJ mol^?1, 32.25 kJ mol and ?130.92 J mol K^?1, respectively. Above all, CAP kept cyclic performance to 100% even at the 7th cycle. We confirmed the reproducibility of approach with other natural polysaccharides. This was due to strong chain entanglement of IPN synthesis which forces the active sites to stay in place during cyclic catalysis reaction. Thus, the IPN strategy ensures longer catalyst life for catalytic methanolysis of NaBH₄ for H₂ generation.     

Catalytic hydrolysis of NaBH4 over titanate nanotube supported Co for hydrogen production

A Co/HTNT catalyst is developed by immobilizing Co on the surface of titanate nanotubes. The microstructure and composition of the catalyst are investigated with atomic absorption spectroscopy (AAS), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Fourier transform infrared spectrometer (FT-IR) and X-ray photoelectron spectroscopy (XPS). The developed Co/HTNT catalyst shows great performance in catalyzing NaBH₄ hydrolysis. The hydrolysis of 25 mg NaBH₄ catalyzed by 50 mg Co/HTNT in 10 g NaOH solution (12.5 wt%) provides a hydrogen production rate of 1.04 L min^?1 g_Co^?1 at 30 °C, and the activation energy of the reaction is 29.68 kJ mol^?1. The high catalytic activity and economical property make this catalyst a promising choice for on-site hydrogen production from NaBH₄ hydrolysis.     

Cost-effective synthesis of carbon loaded Co3O4 for controlled hydrogen generation via NaBH4 hydrolysis

The simple, reliable, and economical process of combustion is used to synthesize carbon loaded cobalt oxide (C–Co₃O₄) for hydrogen generation via NaBH₄ hydrolysis. The effect of NaBH₄ concentration, pH, and temperature of the solution on hydrogen generation is investigated in detail. C–Co₃O₄ exhibits zero order reaction kinetics with respect to NaBH₄ concentration. A stable Hydrogen Generation Rate (HGR) is observed throughout the reaction in the temperature range of 300–315 K using C–Co₃O₄. It is found that 0.01 g of C–Co₃O₄ exhibited high reaction activity with a maximum HGR of 5430 ml min^?1 g^?1 for the optimal solution at 320 K. The activation energy is calculated to be 55.9 kJ mol^?1 for hydrolysis of NaBH₄ using C–Co₃O₄. The present study provides an economical method for the large-scale production of C–Co₃O₄ for hydrogen generation from NaBH₄ hydrolysis, which can pave the way to commercialize hydrogen as a main source of fuel.     

Effect of Al2O3-supported Cu-Schiff base complex as a catalyst for hydrogen generation in NaBH4 hydrolysis

Cu-Schiff base complex which we previously synthesized (Kilinc et al., 2012) is supported on Al₂O₃. The prepared catalyst is characterized by using SEM, XRD, BET, and FT-IR methods. And Al₂O₃-supported complex is used as a catalyst in NaBH₄ hydrolysis reaction for hydrogen generation. NaBH₄ hydrolysis reactions are investigated depending on the concentration of NaBH₄ and NaOH, temperature, percentage of Cu complex, and amount of catalyst. Maximum reaction rates are 44,453.33 and 57,410.00 mL H₂/g.cat.min at 30°C and 50°C, respectively. The activation energy of NaBH₄ hydrolysis reaction is found as 225,775 kJ^.mol^?1. All the experimental results and literature comparisons show that Al₂O₃-supported Cu-Schiff base complex is a very effective catalyst in NaBH₄ hydrolysis for H₂ generation.     

Optimisation of sepiolite clay with phosphoric acid treatment as support material for CoB catalyst and application to produce hydrogen from the NaBH4 hydrolysis

Herein, the CoB catalyst supported on the sepiolite clay treated with phosphoric acid was utilized to produce hydrogen from the NaBH₄ hydrolysis. In order to analyse the performance of the phosphoric acid treated sepiolite clay supported-CoB catalyst, the NaBH₄ concentration effect, phosphoric acid concentration effect, phosphoric acid impregnation time effect, CoB catalyst percentage effect, and temperature effect were studied. In addition, XRD, XPS, SEM, TEM, BET, and FTIR analysis were performed for characterization of Co–B catalyst supported on the acid-treated sepiolite. The completion time of this hydrolysis reaction with Co–B (20%) catalyst supported on the sepiolite treated by 5 M phosphoric acid was approximately 80 min, whereas the completion time of this hydrolysis reaction with acid-free sepiolite-supported Co–B (20%) catalyst was approximately 260 min. There is a five-fold increase in the maximum production rate. The maximum hydrogen production rates of this hydrolysis reaction at 30 and 60 °C were found as 1486 and 5025 ml min⁻¹g⁻¹_catalyst, respectively. Activation energy was found as 21.4 kJ/mol. This result indicates that the acid treatment on sepiolite is quite successful. The re-usability of NaBH₄ hydrolysis reaction by CoB catalyst supported on sepiolite treated phosphoric acid for successive five cycles of NaBH₄ at 30 °C was investigated.     

Highly efficient Co/NC catalyst derived from ZIF-67 for hydrogen generation through ammonia decomposition

Small-size cobalt nanoparticles (NPs) distributed on nitrogen doped carbon support (Co/NC-X) were prepared by pyrolysis of ZIF-67 at various temperatures (X = 500, 600,700 and 800 °C) in nitrogen atmosphere and utilized as catalysts for hydrogen production through ammonia decomposition. Characterizations of the catalysts including XRD, HRTEM, XPS, H₂-TPR, CO₂-TPD, etc., were conducted for structure analysis. The N–C plate obtained from pyrolysis was coated with Co NPs to hinder its aggregation, which made the Co NPs dispersed evenly and increased their dispersion. The calcination temperature and the strong base of the support can adjust the strength of Co–N bond. The activity of the Co/NC-X catalysts is attributed to the high content of Co⁰ and the moderate Co–N bond strength. The ammonia decomposition activity of Co/NC-X catalysts in this paper is higher than many reported Co-based catalysts. Co/NC-600 catalyst demonstrates an ammonia conversion of 80% at 500 °C with a space velocity of 30,000 ml g_cat^?1 h^?1, corresponding to a hydrogen production rate of 26.8 mmol H₂ g_cat^?1 min^?1. The work provides insight for the development of highly active cobalt-based catalysts for hydrogen production through ammonia decomposition.     

Highly efficient acid-treated cobalt catalyst for hydrogen generation from NaBH4 hydrolysis

The effect of cobalt-based catalysts, i.e. CoCl₂(20 wt% Co)/Al₂O₃ treated by different acids, on NaBH₄ hydrolysis was investigated. Five acids were used: oxalic acid, citric acid, acetic acid, sulfuric acid and hydrochloric acid. Two ways of acid treatment were considered: (i) ex-situ addition of acid to CoCl₂(20 wt% Co)/Al₂O₃ at room temperature and (ii) in-situ addition by mixing CoCl₂, Al₂O₃ and acid (one-step process). Both ways showed that adding an acid to the catalyst contributed to an important increase of the catalytic activity towards the NaBH₄ hydrolysis. The best performances were obtained with the catalysts treated with either HCl or CH₃COOH as the global activity of CoCl₂(20 wt% Co)/Al₂O₃ was increased up to 50%.     

Controllable hydrogen production from NaBH4 hydrolysis promoted by acetic acid

Numerous catalysts have been widely investigated for accelerating hydrogen production from NaBH₄ hydrolysis. However, these catalysts are usually complicated in structures, costly in fabrication, and hazardous for environment. In this work, cheap and environment-friendly acetic acid, CH₃COOH, is employed to promote NaBH₄ hydrolysis to produce hydrogen in a considerable rate. The experimental results demonstrate that the addition of suitable amount of CH₃COOH into NaBH₄ solutions stabilized with NaOH could dramatically accelerate the hydrolysis reaction. Additionally, the start/stop of NaBH₄ hydrolysis could be controlled by adding acid or base into the solution to realize “go-as-you-please” on-site hydrogen production.     

Pd nanoparticles immobilized on magnetic carbon dots@Fe3O4 nanocubes as a synergistic catalyst for hydrogen generation

In this work, a cube-like Pd/carbon dots@Fe₃O₄ (Pd/C-dots@Fe₃O₄) hybrid material has been successfully prepared through a facile ultrasonic assisted chemical reduction method, and used as a highly efficient catalyst for the hydrolytic dehydrogenation of NaBH₄ in alkaline media. It is found that the small Pd nanoparticles (NPs) are uniform and well dispersed on the surface of C-dots@Fe₃O₄ nanocubes (NCs). Benefiting from the advantages of the unique cube-like structure, the super conductivity of carbon dots (C-dots) and the synergistic effect between Pd NPs and C-dots@Fe₃O₄ support, Pd/C-dots@Fe₃O₄ NCs exhibits the highest catalytic performance among all the as-prepared samples. The possible reaction mechanism is discussed. Furthermore, the effects of reaction temperature, NaBH₄ concentration and NaOH concentration on the catalytic activity of Pd/C-dots@Fe₃O₄ NCs are studied. Besides, the magnetic properties of Pd/C-dots@Fe₃O₄ NCs can achieve effective momentum transfer with the assistance of the external magnetic field, and a higher catalytic activity is observed for Pd/C-dots@Fe₃O₄ NCs in self-stirring mode than in magnetic-stirring mode. This novel catalyst also exhibits good stability and can be easily separated by a magnet, showing great potential for renewable energy applications.