Comparative study between supported and doped MgO catalysts in supercritical water gasification for hydrogen production

Different catalyst structures may influence the catalytic performance of catalysts in supercritical water gasification (SCWG). This study reports the catalytic activity of supported (SP) and doped (DP) MgO catalysts in catalyzing the gasification of oil palm frond (OPF) biomass in supercritical water to produce hydrogen. Two types of supported catalysts, labelled as Ni-SP (nickel supported MgO) and Zn-SP (zinc supported MgO), were synthesized via impregnation method. Another two types of doped catalysts, labelled as Ni-DP (nickel doped MgO) and Zn-DP (zinc doped MgO), were synthesized by using the self-propagating combustion method. All the synthesized catalysts were found to be pure with the doped catalysts exhibited small crystallites, in comparison to that produced by the supported catalysts. The specific surface area increased in the order of Ni-DP (67.9 m² g⁻¹) > Zn-DP (36.3 m² g⁻¹) > Ni-SP (30.1 m² g⁻¹) > Zn-SP (13.1 m² g⁻¹). Regardless of supported or doped, the Ni-based catalysts always had larger specific surface area than that in the Zn-based catalysts. Unexpectedly, the Zn-based catalysts with smaller surface area for SCWG produced higher hydrogen (H₂) yield from the OPF biomass. When compared to the non-catalytic reaction, the H₂ yield increased by 187.2% for Ni-SP, 269.0% for Zn-SP, 361.7% for Ni-DP, and 438.1% for Zn-DP. Among the studied catalysts, the Zn-DP displayed the highest H₂ yield because it had the highest number of basic sites; approximately twenty-fold higher than that of the Zn-SP catalyst. The Zn-DP also proved to be the most stable catalyst, as verified from the X-Ray photoelectron spectroscopy (XPS) results. As such, this study concludes that the catalytic performances of the synthesized catalysts do not only depend on the specific surface area, but they are also influenced by the number of basic sites and the catalyst stability. It is trustworthy to note that this is the initial study that associated SCWG with doped catalysts. The doped catalysts, hence, may serve as a new catalyst system to generate SCWG reactions.     

Hydrogen production by catalytic gasification of coal in supercritical water with alkaline catalysts: Explore the way to complete gasification of coal

Supercritical water gasification (SCWG) of coal is a promising technology for clean coal utilization. In this paper, hydrogen production by catalytic gasification of coal in supercritical water (SCW) was carried out in a micro batch reactor with various alkaline catalysts: Na₂CO₃, K₂CO₃, Ca(OH)₂, NaOH and KOH. H₂ yield in relation to the alkaline catalyst was in the following order: K₂CO₃ ≈ KOH ≈ NaOH > Na₂CO₃ > Ca(OH)₂. Then, hydrogen production by catalytic gasification of coal with K₂CO₃ was systematically investigated in supercritical water. The influences of the main operating parameters including feed concentration, catalyst loading and reaction temperature on the gasification characteristics of coal were investigated. The experimental results showed that carbon gasification efficiency (CE, mass of carbon in gaseous product/mass of carbon in coal × 100%) and H₂ yield increased with increasing catalyst loading, increasing temperature, and decreasing coal concentration. In particular, coal was completely gasified at 700 °C when the weight ratio of K₂CO₃ to coal was 1, and it was encouraging that raw coal was converted into white residual. At last, a reaction mechanism based on oxygen transfer and intermediate hybrid mechanism was proposed to understand coal gasification in supercritical water.     

Review of heterogeneous catalysts for sub- and supercritical water gasification of biomass and wastes

Nowadays, substantial efforts are devoted to decrease our dependence on fossil fuels. This change will heavily rely on development of new and improved catalytic processes. Over the past two decades, catalytic hydrogen production from wet biomass and organic compounds in sub- and supercritical water (SCW) has gained significant attention. In this process, catalysts are employed to enhance the gas formation rate at moderate temperatures. Catalysts can be also utilized to shift the product distribution toward a more desirable compound (e.g. hydrogen). The effectiveness of various types of heterogeneous catalysts, mainly containing nickel and ruthenium, have been demonstrated for hydrothermal gasification of organic compounds. Catalyst formulation along with operating conditions such as temperature and feed concentration can significantly affect the conversion and selectivity of the process. This paper reviews the major findings of hydrothermal gasification over the past two decades with the aid of heterogeneous catalysts in terms of activity, hydrogen selectivity and stability. Commercially available and laboratory-prepared catalysts including supported and skeletal metal catalysts, activated carbon, oxides, metal wires and other innovative catalysts are considered. Results of supercritical water gasification (SCWG) of various feedstocks reported in the literature are compared and possible mechanisms and rates of deactivation of heterogeneous catalysts are discussed.     

Experimental study on the energy conversion of food waste via supercritical water gasification: Improvement of hydrogen production

In this study, the model food waste was gasified to hydrogen-rich syngas in a batch reactor under supercritical water condition. The model food consisted of rice, chicken, cabbage, and cooking oil. The effects of the main operating parameters including temperature (420–500 °C), residence time (20–60 min) and feedstock concentration (2–10 wt%) were investigated. Under the optimal condition at 500 °C, 2 wt% feedstock and 60 min residence time, the highest H₂ yield of 13.34 mol/kg and total gas yield of 28.27 mol/kg were obtained from non-catalytic experiments. In addition, four commercial catalysts namely FeCl₃, K₂CO₃, activated carbon, and KOH were employed to investigate the catalytic effect of additives at the optimal condition. The results showed that the highest hydrogen yield of 20.37 mol/kg with H₂ selectivity of 113.19%, and the total gas yield of 38.36 mol/kg were achieved with 5 wt% KOH addition Moreover, the low heating value of gas products from catalytic experiments with KOH increased by 32.21% compared to the non-catalytic experiment. The catalytic performance of the catalysts can be ranked in descending order as KOH > activated carbon > FeCl₃ > K₂CO₃. The supercritical water gasification (SCWG) with KOH addition can be a potential applied technology for food waste treatment with production of hydrogen-rich gases.     

Effect of nickel loading on hydrogen production and chemical oxygen demand (COD) destruction from glucose oxidation and gasification in supercritical water

Gasification and partial oxidation of 0.25 molar glucose solution was conducted over different metallic nickel (Ni) loadings (7.5, 11, and 18 wt%) on different catalyst supports (θ-Al₂O₃ and γ-Al₂O₃) in supercritical water. Experiments were carried out at three different temperatures (T) of 400, 450, and 500 °C at constant pressure of 28 MPa and a 30 min reaction time (t). For comparison, some experiments were conducted using high loading commercial catalyst (65 wt% Ni on Silica–alumina). Hydrogen peroxide (H₂O₂) was used as a source of oxygen in the partial oxidation experiments. Oxygen to carbon molar ratios (MR) of 0.5–0.9 were examined to increase the hydrogen production via carbon monoxide (CO) production. Results showed that in the absence of the catalyst, the optimum molar ratio was 0.8 i.e. 80% of the amount of oxygen required for complete oxidation of glucose. At a molar ratio of 0.8, the hydrogen yield was 0.3 mol/mol, as compared to 0.2 mol/mol glucose at molar ratio of 0.5 and 0.9. This optimized oxygen dose was adopted as a base line for catalysts evaluation. The main gaseous products were carbon dioxide (CO₂), carbon monoxide (CO), hydrogen (H₂), and methane (CH₄). Results also showed that the presence of Ni increased the total gas yield increased in the 7.5–18 wt Ni/Al₂O₃ catalyst. An increase in MR from 0.55 to 0.8 increased the of carbon dioxide and hydrogen yields from 1.8 to 3.8 mol/mol glucose and from 0.9 to 1.1 mol/mol. The carbon monoxide and methane yields remain constant at 2 and 0.5 mol/mol glucose, respectively. The introduction of hydrogen peroxide (H₂O₂) prior to the feed injection inhibited the catalyst activity and did not increase the hydrogen yield whereas the introduction of H₂O₂ after 15 min of reaction time increased the hydrogen yield from 0.62 mol/mol to 1.5 mol/mol. This study showed that approximately the same hydrogen yield can be obtained from the synthesized low nickel alumina loading (18 wt%) catalyst as with the 65 wt% nickel on silica–alumina loading commercial catalyst. The highest H₂ yield of 1.5 mol/mol glucose was obtained with commercial Ni/silica–alumina with a BET surface area of 190 m²/g compared to 1.2 mol/mol with the synthesized Ni/θ alumina with a BET surface area of 46 m²/g.     

Catalytic gasification of food waste in supercritical water over La promoted Ni/Al2O3 catalysts for enhancing H2 production

Ni/Al₂O₃ catalyst is the one of promising catalysts for enhancing H₂ production from supercritical water gasification (SCWG) of biomass. However, due to carbon deposition, the deactivation of Ni/Al₂O₃ catalyst is still a serious issue. In this work, the effects of lanthanum (La) as promoter on the properties and catalytic performance of Ni/Al₂O₃ in SCWG of food waste were investigated. La promoted Ni/Al₂O₃ catalysts with different La loading content (3–15 wt%) were prepared via impregnation method. The catalysts were characterized using XRD, SEM, BET techniques. The SCWG experiments were carried out in a Hastelloy batch reactor in the operating temperature range of 420–480 °C, and evaluated based on H₂ production. The stability of the catalysts was assessed by the amount of carbon deposition on catalyst surface and their catalytic activity after reuse cycles. The results showed that 9 wt% La promoter is the optimal loading as Ni/9La–Al₂O₃ catalyst performed best performance with the highest H₂ yield of 8.03 mol/kg, and H₂ mole fraction of 42.46% at 480 °C. La promoted Ni/Al₂O₃ catalysts have better anti-carbon deposition properties than bare Ni/Al₂O₃ catalyst, resulting in better gasification efficiency after reuse cycles. Ni/9La–Al₂O₃ catalyst showed high catalytic activity in SCWG of food waste and had good stability as it was still active for enhancing H₂ production when used in SCWG for the third time, which indicated that La promoted Ni/Al₂O₃ catalysts are potential additive to improve the SCWG of food waste.     

Catalytic gasification of light and heavy gas oils in supercritical water

Canada has the third-largest oil sand reserves in the world as a result of which, it generates considerable amounts of light gas oil and heavy gas oil through petroleum distillation. With the escalating energy demands, it has become essential to explore alternative fuel resources from biomass and petrochemical residues. This study explores the potential of supercritical water gasification to transform light and heavy gas oils to hydrogen-rich syngas through the optimization of process conditions such as temperature (375–675 °C), feed concentration (20–35 wt%) and reaction time (30–75 min). Nickel-supported functionalized carbon nanotubes (10%Ni/FCNT) were synthesized for application in catalytic supercritical water gasification. The functionalization of carbon nanotubes resulted in an increase in their surface area from 108 m²/g (in pristine CNT) to 127 m²/g (in FCNT) and 122 m²/g (in 10%Ni/FCNT). The impregnation of catalytic nickel particles onto carbon nanotubes was confirmed through X-ray diffraction (XDR) and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS). Fourier-transform infrared (FTIR) spectroscopy of both gas oils revealed the presence of aliphatics, alkyl-aryl ethers and sulfur-containing compounds among several other aromatics. Light gas oil revealed higher hydrogen yields of 3.32 mol/kg compared to that of heavy gas oil (2.79 mol/kg) at optimal process conditions, i.e. 675 °C and 75 min, 20 wt% feed concentration. However, 10%Ni/FCNT enhanced hydrogen yields (4.46 mol/kg), total gas yield (9.22 mol/kg), hydrogen selectivity (94%) and lower heating value (1685 MJ/kg) of product gases obtained from light gas oil in contrast to heavy gas oil. This study indicates a tremendous potential of gas oils for hydrogen generation via hydrothermal gasification.     

Influence of AlCl3 and oxidant catalysts on hydrogen production from the supercritical water gasification of dewatered sewage sludge and model compounds

Hydrogen has attracted significant attention as a clean energy source. Supercritical water gasification (SCWG) technology can produce hydrogen-rich gas while also disposing of sludge. The hydrogen yield from the SCWG of sludge is greatly increased when catalyzed by AlCl₃. In this paper, a combined catalyst based on AlCl₃ was proposed to further increase the hydrogen yield of SCWG of dewatered sewage sludge (DSS). Analysis of the products from catalytic gasified of DSS and its model compounds were used to propose a catalytic mechanism and reaction pathway of the catalytic SCWG of DSS. Among the combined catalysts used for the SCWG of DSS, 10 wt% AlCl₃–H₂O₂ (mass ratio 8:2) had the best hydrogen production effect, and the hydrogen yield reached 8.88 mol/kg organic matter. This was 14% higher than when catalyzed by 10 wt% AlCl₃. During catalysis with AlCl₃, Al³⁺ reacted with OH⁻ in water and precipitated as Al(OH)₃, which produced an acidic environment in the liquid product. Al(OH)₃ dehydrated to form an AlO(OH) and deposited in the solid product. A small amount of H₂O₂ promoted the steam reforming reaction of organic matter in DSS, which increased the hydrogen yield. H₂O₂ further promoted the hydrogen yield in an acidic environment. The catalytic effect of AlCl₃ was unaffected by H₂O₂. The H⁺ generated by AlCl₃ during catalysis promoted H₂O₂ to further depolymerized organic matter (such as humic substances) in DSS, so that AlCl₃–H₂O₂ catalyzed the SCWG of DSS to further increase the hydrogen yield. The order of hydrogen yield catalyzed by AlCl₃–H₂O₂ was guaiacol > humic acid > glycerol > alanine > glucose. Compared with AlCl₃, AlCl₃–H₂O₂ reduced the hydrogen yield of glucose by nearly 20% and increased the hydrogen yield of humic acid by about 17% (25.81 mol/kg feed).     

Influence of sludge properties on the direct gasification of dewatered sewage sludge in supercritical water

In the present study, ten different types of dewatered sewage sludges were treated in supercritical water in a high-pressure autoclave under a given condition (at 400 °C, 60 min and 23 MPa). The feasibility of direct gasification and the effect of sludge properties on the gasification of dewatered sewage sludge with various properties in supercritical water were investigated. The results showed that dewatered sewage sludge with various water contents (73.48–88.51 wt%), organic matter contents (29.25–73.02 wt%, on dry basis) and inorganics can be directly gasified in supercritical water. The total gas and phenol production increased linearly with the increment of organic matter content in dewatered sewage sludge. The difference in hydrogen content in the gaseous product may be related to the content of water and inorganic as well as pH value of the sludge. The char/coke formed in the solid residue increased with decrement of water content, which inhibited the gasification reaction and resulted in the carbonization reaction.     

Catalytic performances of Ni-based catalysts on supercritical water gasification of phenol solution and coal-gasification wastewater

Activity and stability of the supported Ni-based catalysts for the gasification performances of phenol solution and coal-gasification wastewater in supercritical water were studied in a continuous reactor at 480 °C, 25 MPa and oxygen ratio of 0.2 for 50 h operation. The influences of the supports (γ-Al₂O₃, active carbon (AC) and carbon nanotube (CNT)) on gas yields, gasification efficiencies for phenol solution were investigated, and the loading amount of Ni were optimized. Results showed that the catalytic activity and the stability of the catalysts followed the order of Ni/CNT > Ni/AC > Ni/γ-Al₂O₃. The activity of Ni/AC and Ni/γ-Al₂O₃ decreased after 30 h continuous operation, and there occurred significant leaching of Ni²⁺. For Ni/CNT catalyst, H₂ yield increased obviously when the loading amount of Ni lower than 15 wt%, while increased little at higher loading amount. Then, 15 wt% Ni/CNT with a thickness of 1.5 mm was coated on 316 L stainless steel (SS316L, an economic material usually used as the reactor material), which can act as a "catalytic tube wall" in reactor. The catalytic activity and corrosion resistance of Ni/CNT/SS316L for the gasification of real coal-gasification wastewater were studied. Results showed that Ni/CNT/SS316L gave a great positive effect on H₂ production. H₂ yield increased from 25.36 mmol/g (total organic carbon) without catalyst to 75.12 mmol/g (total organic carbon) with Ni/CNT/SS316L after operated for 20 h, respectively. However, obvious pealing of the coating was found after 50 h operation. Further study is necessary for the improvement of the coating preparation method.     

Hydrogen production via supercritical water gasification of almond shell over algal and agricultural hydrochars as catalysts

Almond shell is one of the most abundant agricultural wastes in Kurdistan province of Iran. Conversion of almond shell into hydrogen-rich gas via supercritical water gasification (SCWG) was investigated in this study using a tubular batch micro-reactor system. Non-catalytic tests were carried out in different conditions to determine the optimum condition for H₂ production. Maximum hydrogen yield of 7.85 mmol/g, was observed in the temperature of 460 °C, residence time (RT) of 10 min and feed/water ratio (F/W) of 0.01. Catalytic experiments were performed using hydrochars as solid residues remained after SCWG of Cladophora glomerata (C. glomerata) macroalgae and wheat straw. Hydrochars were characterized by ICP-OES, FESEM and BET methods. For catalytic experiments, hydrochars were added to the almond shell by the weight ratio of 0.4. Conversion of almond shell and hydrogen production, were more influenced by the presence of inorganic compounds in the hydrochars rather than the surface area and pore volume. The maximum hydrogen yields of 10.77 and 11.63 mmol/g, were observed for catalytic experiments in the presence of wheat straw and C. glomerata hydrochars, respectively.     

Molecular dynamics investigation on the gasification of a coal particle in supercritical water

Coal gasification technology in supercritical water provides a clean and efficient way to convert coal to H₂. In the present paper, the whole supercritical water（SWC）gasification process of a coal particle is studied with the reactive force field (ReaxFF) molecular dynamics (MD) method for the first time. First, the detailed reaction mechanism which can't be clearly illustrated in experiments, such as the evolution of the carbon structure during the gasification process and the detailed reaction mechanism of the main products, is obtained. According to the generation mechanism of H₂, it is found that the supercritical water gasification process of a coal particle can be divided into two stages with different reaction mechanisms, namely the rapid reaction stage and the stable reaction stage. Then, the effects of temperature and coal concentration in the reaction system on the yield of H₂ are studied. Finally, the transition of N in the coal particle is revealed, in which the precursors of NH₃ such as CN, CHN, and CHON are the basic molecular structures for nitrogen atoms during the gasification process at high temperature.     

Hydrogen generation by gasification of phenol and alcohols in supercritical water

The conversion of phenol, cyclohexanol (a hydrogenated analog of phenol for comparison with phenol), and ethanol into gas products in supercritical water (SCW) was studied with the goal to compare the reactivity of their aqueous solutions with the structural features obtained by the method of classical molecular dynamics. Transformation of phenol and alcohols occurs in different ways. In the case of alcohols, the conversion of 75–100% is achieved at 600 °C with noticeable gasification. At the same time, the conversion of phenol is only 47% and no gas products are formed at all. The complete conversion of phenol is achieved at a temperature of 750 °C, while the degree of gasification does not exceed 30%. It is shown that an increase in the phenol gasification degree is possible by pre-catalytic hydrogenation of phenol into cyclohexanol.     

Valorization of sewage sludge through catalytic sub- and supercritical water gasification

Sub- and supercritical water gasification is applied to recover energy from sewage sludge in a batch reactor. The effects of reaction temperature and water-soluble additives as catalysts on gasification were examined. The resultant products, including syngas, hydrochar and liquid residues were characterized. The rise of temperature without the presence of catalysts increased the yield of H₂ (0.06 (350 °C) to 1.91 mol/kg (450 °C) and enhanced the gasification efficiency (1.29–19.61%), and decreased total organic carbon (TOC) by 68.50% in liquid residue. The changes in product distribution and characteristics of hydrochar and liquid residue implied that the organic matters in sewage sludge were dissolved and hydrolyzed in sub- and supercritical water, resulting in the production of syngas. The catalytic effect of different catalysts in relation to the H₂ gas yield was in the following order: KOH > NaOH > Na₂CO₃ ≈ K₂CO₃. In the case of catalytic supercritical water gasification at 400 °C, the highest molar fraction (37.28%) and yield of H₂ (1.60 mol/kg) were obtained in the presence of KOH. Furthermore, the scanning electron microscopy (SEM) analysis indicated that a conversion and dissolution of the organic matters in sewage sludge to liquid and gas, produced a porous, fragmented structure and disintegrated surface of hydrochar.     

Thermodynamic study on the integrated supercritical water gasification with reforming process for hydrogen production: Effects of operating parameters

In this paper, a conceptual process design of the integrated supercritical water gasification (SCWG) and reforming process for enhancing H₂ production has been developed. The influence of several operating parameters including SCWG temperature, SCWG pressure, reforming temperature, reforming pressure and feed concentration on the syngas composition and process efficiency was investigated. In addition, the thermodynamic equilibrium calculations have been carried out based on Gibbs free energy minimization by using Aspen Plus. The results showed that the higher H₂ production could be obtained at higher SCWG temperature, the H₂ concentration increased from 5.40% at 400 °C to 38.95% at 600 °C. The lower feed concentration was found to be favorable for achieving hydrogen-rich gas. However, pressure of SCWG had insignificant effect on the syngas composition. The addition of reformer to the SCWG system enhanced H₂ yield by converting high methane content in the syngas into H₂. The modified SCWG enhanced the productivity of syngas to 151.12 kg/100kg_feed compared to 120.61 kg/100kg_feed of the conventional SCWG system. Furthermore, H₂ yield and system efficiency increased significantly from 1.81 kg/100kg_feed and 9.18% to 8.91 kg/100kg_feed, and 45.09%, respectively, after the modification.     

Coupling of hydrothermal pretreatment and supercritical water gasification of sewage sludge for hydrogen production

In this study, hydrothermal pretreatment and supercritical water gasification were coupled to form a combined process for the treatment of dewatered sludge for hydrogen production. First, the effects of varying hydrothermal pretreatment conditions on the transformation of organic matter in sludge were studied. Results showed that about 31% of the carbon in sludge was transferred into liquid products at 250 °C for 60 min, which were considered to be the optimal pretreatment conditions considering both the hydrothermal pretreatment effects and the energy consumption requirements. The organic matter components were determined, showing that 87% of the carbohydrate components in sludge were transformed during the process of hydrothermal pretreatment, with 49% of crude proteins and 62% of humus remaining in the solid phase products. During the subsequent process of supercritical water gasification, AlCl₃, KOH, K₂CO₃ and CaO were selected as catalysts. Compared with directly catalyzed supercritical water gasification of sludge, the integrated process was found to improve H₂ selectivity, H₂ yield and energy recovery. Moreover, the use of AlCl₃ as a catalyst showed the highest H₂ yield and energy recovery. The H₂ yield and the energy recovery increased by 45.1% and 13.2%, respectively.     

Oleic acid gasification over supported metal catalysts in supercritical water: Hydrogen production and product distribution

Oleic acid was examined as a model compound for lipids, which was gasified in supercritical water (SCW) using a batch reactor from 400 to 500 °C at 28 MPa. The influence of operating temperature and several commercial catalysts on the gasification efficiency, hydrogen gas yield, and residual liquid product quality was examined and discussed. The main gaseous components measured were carbon dioxide (CO₂), hydrogen (H₂), methane (CH₄), and traces of carbon monoxide (CO). The residual liquid after reaction was characterized by analyzing the chemical oxygen demand (COD), total organic carbon (TOC), volatile fatty acids (VFAs), and the long chain fatty acids (LCFAs), namely, palmitic, myristic, stearic, linoleic, and oleic acids. The results showed that an increase of temperature coupled with the use of catalyst enhanced the gas yield dramatically. The H₂ yield was 15 mol/mol oleic acid converted using both the pelletized Ru/Al₂O₃ and powder Ni/Silica-alumina catalysts which gave 4 times higher than the equilibrium yield. The COD reduction efficiency ranged from 31% at 400 °C without catalyst to 96 % at 500 °C in the presence of Ni/Silica-alumina catalyst. The composition of residual liquid products was studied using gas chromatography/mass spectrometry (GC-MS), with a generalized reaction pathway for oleic acid decomposition in SCW reported.     

Experimental basic factors in the production of H2 via supercritical water gasification

This study aims to discuss some of the factors that influence the production of hydrogen via the gasification of organic matter in supercritical water. These factors have been investigated based on the reactions of organic matter with relatively simple chemical structures, such as ethanol, glycerol, and glucose. Investigations of these relatively simple organic materials demonstrate the characteristics and trends in the gasification in supercritical water. The results reported in the literature for these organic compounds can also be extrapolated to the reactions of biomass containing ethanol, glucose, (sugar cane industry) and glycerol (biodiesel industry) in supercritical water. Many organic compounds with different levels of molecular complexity can be used to produce hydrogen, which represents an interesting form of energy storage. Supercritical water (T_c ≥ 374 °C, P_c ≥ 22.1 MPa) has unique physical and chemical properties that minimize mass transport limitations, making it an excellent medium for the decomposition of organic compounds. Thus, understanding the key factors that influence organic compound gasification in supercritical water is extremely important. In this study, we summarize some of the key factors involved in these reactions. The main experimental factors were confirmed to be the temperature, concentration of organic matter in the feed, space time/feed rate, catalysts, oxidants, material and design of the reactor, and pressure. In addition, operational challenges, namely, catalyst deactivation and corrosion are mentioned in the text. Furthermore, the operational challenges were discussed, and the state of the art regarding the gasification of ethanol-, glycerol-, and glucose-containing biomass is also presented.     

Influence of moisture content on the direct gasification of dewatered sludge via supercritical water

In the present study, the feasibility of the direct gasification of dewatered sludge in supercritical water and the effect of water content on supercritical water gasification of the dewatered sludge were investigated using a high-pressure autoclave at a constant temperature of 400 °C with residence time of 60 min and by adjusting water content by adding distilled water or using air-dried dewatered sludge. The results showed that dewatered sludge can be directly gasified in supercritical water, with water content ranging from 75 to 95 wt%. The total gas production was increased by decreasing the water content, and the gas yield was decreased. The CO₂ yield was significantly affected by water content, whereas H₂, CH₄, and CO yields were slightly reduced. The liquid residue contained large amounts of organic matter (OM) and total phenols, thereby requiring further treatment before being discharged. The concentrations of OM and total phenols increased with a decrease in water content. Moreover, a serious carbonization reaction happened while carbon particles higher than 10 wt% (char/coke) were being formed in the solid residue.     

Hydrogen production from the gasification of lignin with nickel catalysts in supercritical water

Hydrogen production from the gasification of lignin with Ni/MgO catalysts in supercritical water was conducted using stainless steel tube bomb reactor. Ni/MgO catalysts were prepared by impregnation method and were calcined at 773–1173 K in air for 8 h. The results of characterization for reduced Ni/MgO catalysts showed that Ni metal and NiO–MgO phase are formed after the reduction of calcined catalyst by _H2${\mathrm{H}}_2$. Furthermore, Ni metal surface area, which was calculated by CO chemical adsorption technique, decreased with increase in calcination temperatures. It was found that the carbon yield of gas products was increased with increase in Ni metal surface area except 10 wt% Ni/MgO (773 K) catalyst. Thus, it can be supposed that there is an optimal Ni particle size for the gasification of lignin in supercritical water. It should be noted that 10 wt% Ni/MgO (873 K) catalyst showed the best catalytic performance (carbon yield 30%) under reaction condition tested. It was concluded that Ni/MgO catalyst is a promising system for the gasification of lignin in supercritical water.