Coating and Characterization of Titania Membrane on Porous Ceramic Supports

In this article, we reported experimental results on the development of microstructure of the membrane layer deposited on a porous support. The changes in porosity and mean pore diameter were followed as a function of layer thickness. It was found that in addition to particle packing and sintering within the membrane layer, the porous structure of support surface also exhibited certain effects on membrane microstructure until a critical thickness was reached. After that, the porous characteristics of a membrane would be totally determined by the packing and sintering characteristics of particles. It was also shown that the surface roughness could be reduced from about 1.5 m of the support, to 0.8 m after coating with 0.5 m titania particle and further reduced to about 0.55 m after another coating with 30 nm titania colloids. With proper dispersing and coating procedures, we could reduce the mean pore diameter from about 1.5 m of the support to 0.12 m, while the gas permeability was only changed from 500 × 10–7 to 250 × 10–7 mol/m2 s Pa.     

Antimony in lead-acid cells. III. Transport measurements

The mechanism of transport of Sb(V) in H₂SO₄ through 12 commercial separators was investigated. This was carried out by comparing the diffusion coefficient of Sb(V) with the electrical ionic conductivity which should be simply related if diffusion is the rate-controlling transport process. Rates increased as convective flow became dominant. Separators with pore diameters below 2 m and above 20 m showed transport rate control by diffusion and convective flow, respectively. Between 2 and 20 m both processes contributed significantly.     

A Study and Comparison of the Properties of Bauxite Treated by Dry and Wet Grinding Techniques

The kinetics of dry and wet grinding of a sintered bauxite treated using a ball mill is studied. By the dry grinding technique, a dispersity characterized by a median particle diameter of about 17 m and average surface particle diameter of about 5 m can be reached. By the wet grinding technique, a higher degree of dispersion of the material is reached (of median diameter less than 3 m), with a certain amount of nanoparticles produced.     

Selective catalytic reduction of nitric oxide over vanadia grafted on titania. Influence of vanadia loading on structural and catalytic properties of catalysts

The selective catalytic reduction (SCR) of NO by NH₃ has been studied over vanadia/ titania catalysts prepared by selective immobilization of vanadyl alkoxide species on two structurally different titania supports. The loading of vanadia was varied from 1.8 to 7.5 ,mol V⁵⁺ per m² surface area. Comparative kinetic measurements at 150 °C show that the NO turnover frequencies increase by more than an order of magnitude when the vanadia loading is increased from 1.8 to 3 mol V⁵⁺/m². In the region of lower SCR activity, i.e. at lower coverages ( 2 mol V⁵⁺/m²), small clusters and ribbons of vanadia are detected in the Raman spectra, whereas at loadings where maximum NO turnovers are achieved ( 3 mol V⁵⁺/m²) the prevalent vanadia species are well-developed two-dimensional vanadia layers bound to titania.     

Characterization of some organic poly(aminiumphosphate)s

Summary Metachromatic reactions of MB and AO are studied with poly(aminium phosphate)s. The main band() at 665 m and 492 m for MB and AO are shifted to 580 m and 455 m respectively (-bands). The metachromatic values at different concentrations of poly(aminium phosphate)s are also reported. The dye association for MB with these polymer derivatives is investigated conductometrically as well. It is observed that MB can be at the most bind with the phosphate residue of polymer upto 11 molar ratio. The polymeric nature was further established by paper chromatographic technique in Terry's, Ebel's & Pfrengle's solvents.     

Diffusion-controlled current distributions near cell entries and corners

This paper reports experimental work undertaken to explore diffusion-controlled current distributions immediately downstream of sudden changes in flow cross-sectional area such as may occur at the entry to electrochemical flow cells. Nozzle flows expanding into an axisymmetric circular duct and into a square duct have been investigated using the reduction of ferricyanide ions on nickel micro-electrodes as the electrode process. The spanwise distribution of current has also been studied for the case of the square cell where secondary corner flows are significant.Nomenclature A electrode area (cm²) - c bulk concentration of transferring ions (mol dm^–3) - D cell diameter (cm) - D Diffusion coefficient (cm₂s^–1) - F Faraday number (96 486 C mol^–1) - I limiting electrolysis current (A) - k mass transfer coefficient (cm s^–1) - N nozzle diameter (cm) - u mean fluid velocity (cm s^–1) - x distance downstream from point of entry to cell (cm) - z number of electrons exchanged - electrolyte viscosity (g s^–1 cm^–1) - electrolyte density (g cm^–3) - (Re)_D duct Reynolds number,Du/ - (Re)_N nozzle Reynolds number,Nu/ - (Sc) Schmidt number,/D) - (Sh) Sherwood number,kD/D)     

Alleviation of α-tomatine-induced toxicity to the parasitoid,Hyposoter exiguae,by phytosterols in the diet of the host,Heliothis zea

The solitary, endoparasitic ichneumonid,Hyposoter exiguae (Viereck) is a parasitoid of the tomato fruitworm,Heliothis zea (Boddie). However, the parasitoid is deleteriously affected by the tomato glycoalkaloid, -tomatine, ingested from hosts (H. zea) fed on artificial diets or semipurified extracts of tomato plants that contained -tomatine. -Tomatine causes prolonged larval development; disruption or prevention of pupal eclosion; deformation of antennal, abdominal, and genital structures; and reduction in adult weight and longevity of the parasitoid. These toxic effects are exacerbated when the dietary dose of -tomatine is increased from 12 mol to 20 mol/g dry wt of diet. However, the toxicity of -tomatine is attenuated in parasitoids reared from hosts fed on artificial diets that contain equimolar or supramolar amounts of 3-OH-sterols admixed with -tomatine. Further, the toxicity of extracts from the foliage of different cultivars of tomatoes toH. exiguae is contingent upon the composite levels of -tomatine and total phytosterol (free and esterified). Cultivars with a low total sterol-tomatine ratio are more toxic toH. exiguae. The possible mode of action of -tomatine toxicity toH. exiguae by disruption of sterol metabolism is discussed.     

Isolation,characterization and activity of phytotoxic compounds from quackgrass [Agropyron repens (L.)Beauv.]

Previous experiments showed that legumes grown in the presence of living or herbicidally treated quackgrass residues or extracts exhibited reduced seedling root and shoot growth and decreased nodulation and nitrogen fixation. Aqueous extracts of quackgrass shoots were most inhibitory to plant growth. Upon sequential partitioning of an aqueous extract of quackgrass shoots, the ether extract possessed the most activity and caused 50% reductions in radicle elongation of eight crop and weed species at concentrations of less than 240 g/ml (small-seeded species) and 1000 g/ml (large-seeded species). Snapbeans (Phaseolus vulgaris L. Bush Blue Lake) grown aseptically in agar containing an ether extract at 100 and 200 g/ml exhibited severe root browning, lack of root hair formation, and a two- to three-fold reduction in root and shoot dry weights. The ether extract of quackgrass shoots had no inhibitory effect on the growth of fourRhizobium species in Petri dishes or two species in broth culture. Inhibitors present in the ether extract may influence the legumeRhizobium symbiosis indirectly by reducing legume root growth and root hair formation. The ether extract of quackgrass shoots was separated using high-pressure liquid, thin-layer, and liquid column chromatography in an attempt to isolate and identify the inhibitors responsible for the inhibition of seedling growth. Two closely related flavonoid inhibitors were isolated from the ether extract. One was identified as 5,7,4-trihydroxy-3,5-dimethoxyflavone (tricin). Both flavonoids caused 50% inhibition of radicle elongation in cress (Lepidium sativum L. Burpee curly) seeds at concentrations of less than 125 g/ml. Both flavonoids were found in ether extracts of quackgrass shoots and rhizomes, but the largest amounts of both compounds occurred in quackgrass shoots collected from the field.Journal article No. 11887 of the Michigan Agricultural Experiment Station.     

Grafting onto TEDLAR films by the electron beam preirradiation technique

Summary Polyvinylfluoride (tedlar) films, 12.5–25 m thick, were grafted with acrylamide monomer (AM) in an aqueous solution, following preirradiation with a 550 kV electron beam accelerator. The graft yield rose with grafting period up to 285% and 475%, for the 25 m and the 12.5 m tedlar films, respectively, and then levelled off due to gelation of the solution.Water permeation rates through the tedlar films were increased, upon grafting with AM, by a factor of up to 3. Water permeation rates through the tedlar grafted with acrylamide (TEDgAM) films were relatively low, as compared with those of cellophane films or nylon grafted acrylamide films (NYgAM) of comparable thickness, implicating that only part of the tedlar film cross-section has been penetrated through by the grafted copolymer. The highest rates of water permeability were observed in 12.5 m films grafted with 475% acrylamide.     

Interactions between pheromone traps with different strength lures for the pine beauty moth,Panolis flammea (Lepidoptera: Noctuidae)

Catches of malePanolis flammea in traps baited with lures containing 25 g of sex attractant are enhanced when in the proximity of traps baited with 125-g lures. The degree of enhancement is increased as the intertrap distance is decreased, and when the low-dose trap is upwind of the high-dose one. The patterns of alteration in trap catch suggest that moths initially attracted by one lure may divert into other traps, which may be either upwind of the original trap (overshooting), or downwind (undershooting). Overshooting can result in up to fivefold increases in catch and may provide a useful method for estimating the attractant zone of particular lure/trap combinations.     

Isolation and Identification of Primary Metabolite Feeding Stimulants for Adult Western Corn Rootworm, Diabrotica virgifera virgifera Leconte, from Host Pollens

Consumption of pollens from several host plants was quantified for adult western corn rootworm, Diabrotica virgifera virgifera, with significantly more sweet corn and winter squash pollen consumed than that of common sunflower and Canada goldenrod. Sequential solvent extraction and chromatographic fractionation of host pollens, guided by a feeding bioassay of respective fractions, isolated dominant phagostimulatory activity in pools of free amino acids. Amino acid profiles were determined by TLC and HPLC analysis. For sweet corn pollen, proline was predominant, accounting for 70% of a total 95.3 mol free amino acid/g pollen; serine, alanine, -aminobutyric acid (GABA), and asparagine occurred in decreasing order of concentration. In squash pollen, -alanine predominated (30% of 111 mol amino acid/g pollen), followed by asparagine, alanine, proline, and GABA. Histidine (42% of 83.8 mol amino acid/g pollen), proline, aspartic acid, asparagine, and alanine were dominant for sunflower pollen; and for goldenrod, proline (51% of 50.6 mol amino acid/g pollen), trans-hydroxyproline, serine, histidine, and alanine predominated. The five dominant amino acids from each pollen accounted for 80–90% of total amino acid content. Simple mixtures of some dominant amino acids, approximating levels found in sweet corn and squash pollen, gave phagostimulation similar to that of the crude extracts.     

Linamarin and histamine in the defense of adultZygaena filipendulae

We determined the protective values of histamine and linamarin to an aposematic moth,Zygaena filipendulae. Using ion-exchange resin techniques, we found that the mean histamine concentrations in the wings were 0.061 ± 0.047 g/mg and 0.013 ± 0.0051 in the moths' bodies (totals: 0.586 g and 2.921 g, respectively, all wet weights). Average HCN evolution (mainly from the bitter cyanogen linamarin) from the wings was 0.049 ± 0.41 g/mg (0.426 g/ml of linamarin could produce this amount of HCN) and 0.029 ± 0.0026 g/mg HCN (0.281 g/mg linamarin) evolved from the bodies (total linamarin 4.09 g and 61.258 g, respectively, all wet weights). Therefore, higher concentrations of toxicants were found in the part of the body most liable to initial attack. We found, in offering various toxic solutions to 10 common quails, that 0.1% linamarin (mean linamarin consumed equal to about 70% of the average total wing content) but 1.0% histamine (mean histamine consumed equal to that found in about 8.9 average wing sets) solutions significantly lowered drinking rates. However, combination solutions were still effectively aversive at 0.001% histamine plus 0.028% linamarin. This synergism would allow a moth under local abiotic or dietary stress to elaborate substantially less of one or both compounds than that normally synthesized. The implications to kin selection are discussed.     

Caste-dependent pheromones in the head of the antTetramorium caespitum

The heads of maleT. caespitum contain 4-methyl-3-hexanol (1.7 g, only the erythro isomer(s) detected) and 4-methyl-3-hexanone (0.8 g). The heads of alate females contain 0.1 g of each compound, whereas only the alcohol (0.1 g) was found in the heads of workers. Both compounds act as attractants for the workers and their possible functions are discussed.'Chargé de Recherche du F.N.R.S.Chercheur qualifié du F.N.R.S.     

Porous mullite ceramics through diphasic gels of large boehmite and small silica particles

Mullite formation process has been studied in stoichiometric mullite (3Al₂O₃·2SiO₂) diphasic gel containing large boehmite (1 m) and small silica (10 nm) particles. It has been found that initial mullitization did not take place inside the silica phase (cristobalite), but took place in the defect -alumina phase. -alumina was stabilized by silica when the temperature was below 1350°C. At temperatures above 1350°C, mullite crystallized directly. It was suggested that silica diffused into the pores (<1.8 nm) of -alumina and prevented the collapse of -alumina pore structure. On the other hand, when silica was not present, the pore structure of -alumina collapsed and -alumina crystallized at 1100°C. Porous mullite ceramics were obtained by using special diphasic gels containing large boehmite and small silica particles.     

Identification of cantharidin in false blister beetles (Coleoptera,Oedemeridae) from florida

Cantharidin, a potent vesicant and antifeedant, is identified for the first time in two oedemerid beetles from the western hemisphere. Amounts of the substance per beetle were found to range from 2 to 7 g inHeliocis repanda and from 15 to 35 g inOxycopis thoracica. Females had two to three times more cantharidin than males of the same species. Cantharidin loads of these beetles are sufficient to irritate human skin.     

Leaf surface chemicals fromNicotiana affecting germination ofPeronospora tabacina (adam) sporangia

A bioassay was used to evaluate the effects of cuticular leaf components, isolated fromN. tabacum, N. glutinosa (accessions 24 and 24a), and 23other Nicotiana species, on germinationof P. tabacina (blue mold). The leaf surface compounds included- and-4,8,13,-duvatriene-l,3-diols (DVT-diols), (13-E)-labda-13-ene-8-,15-diol (labdenediol), (12-Z)-labda-12,14-diene-8-ol (cis-abienol), (13-R)-labda-8,14-diene-13-ol (manool), 2-hydroxymanool, a mixture of (13-R)-labda-14-ene-8,13-diol (sclareol), and (13-S)-labda-14-ene-8,13-diol (episclareol), and various glucose and/or sucrose ester isolates. The above in acetone were applied onto leaf disks of the blue moldsusceptibleN. tabacum cv. TI 1406, which was then inoculated with blue mold sporangia. Estimated IC₅₀ values (inhibitory concentration) were 3.0g/cm² for-DVT-diol, 2.9/cm² for-DVT-diol, 0.4g/cm² for labdenediol and 4.7g/cm² for the sclareol mixture. Manool, 2-hydroxymanool, andcis-abienol at application rates up to 30g/cm² had little or no effect on sporangium germination. Glucose and/or sucrose ester isolates from the cuticular leaf extracts of 23Nicotiana species and three different fractions fromN. bigelovii were also evaluated for antimicrobial activity at a concentration of 30g/cm². Germination was inhibited by >20% when exposed to sugar esters isolated fromN. acuminata, N. benthamiana, N. attenuata, N. clevelandii, andN. miersii, and accessions 10 and 12 ofN. bigelovii. These results imply that a number of compounds may influence resistance to blue mold in tobacco.     

Effect of juvenile hormone analog,fenoxycarb, on pheromone production byIps paraconfusus (Coleoptera: Scolytidae)

Topical application of the juvenile hormone analog, fenoxycarb, in acetone induced newly emerged male California five-spined ips,Ips paraconfusus Lanier, to become attractive to females, as measured by positive responses to male abdominal extracts in a laboratory bioassay. Two pheromones, ipsdienol and ipsenol, were detected by gas chromatography in the abdominal extracts of fenoxycarb-treated males. Pheromone production was minimal at a dose of 0.1 g/insect of fenoxycarb, maximal at 10 g, and was reduced to unmeasurable amounts at a dose of 100 g. In comparison, peak production of pheromones was induced at a dose of 0.1 g/insect of natural juvenile hormone (JH III). Treatment with 10 g of fenoxycarb resulted in the occurrence of pheromones 12 hr after exposure, maximal pheromone content between 16 and 20 hr, and undetectable amounts after 36 hr. The demonstration that fenoxycarb is an active juvenile hormone analog for a bark beetle suggests that it may have practical utility in managing these insects.     

Evaluation of vetiver oil and seven insect-active essential oils against the Formosan subterranean termite

Repellency and toxicity of 8 essential oils (vetiver grass, cassia leaf, clove bud, cedarwood, Eucalyptus globules, Eucalyptus citrodora, lemongrass and geranium) were evaluated against the Formosan subterranean termite, Coptotermes formosanus Shiraki. Vetiver oil proved the most effective repellent because of its long-lasting activity. Clove bud was the most toxic, killing 100% of termites in 2 days at 50 g/cm². The tunneling response of termites to vetiver oil also was examined. Vetiver oil decreased termite tunneling activity at concentrations as low as 5 g/g sand. Tunneling and paper consumption were not observed when vetiver oil concentrations were higher than 25 g/g sand. Bioactivity of the 8 oils against termites and chemical volatility were inversely associated. Listed in decreasing order of volatility, the major constituents of the 8 oils were: eucalyptol, citronellal, citral, citronellol, cinnamaldehyde, eugenol, thujopsene, and both - and - vetivone. Vetiver oil is a promising novel termiticide with reduced environmental impact for use against subterranean termites.     

Effect of grain size on the synthesis of active alumina from gibbsite by flash calcination and rehydration

Two series of alumina have been prepared by flash calcination (FCAL) and subsequent rehydration of coarse (> 50 m) and fine grain size gibbsite (< 50 m). The initial grain size of the gibbsite was found to determine the degree of amorphization, water content, rehydration ability, composition and pore structure of FCAL products. Active alumina materials having pore structure parameters similar to those of commercial alumina adsorbents and catalyst supports were obtained by FCAL and subsequent rehydration of fine grain size gibbsite.     

Effect of Granule Size on the Structure of Nanoporous Ceramics Based on Organosilicon Polymer

Porosity in nanoporous ceramics produced by pyrolysis of organosilicon polymer at a temperature of 600°C was investigated using the BET method. Samples were molded from fractionated granules produced by single or double milling in a planetary mill of a polymer previously solidified and heat-treated at 200°C. Specific surface area depending on nanopores sharply decreases after the granules reach a size over 250 m in single milling and over 1000 m in double milling. An explanation for these facts is given in the context of synergism.