Direct injection of hydrogen main fuel and diesel pilot fuel in a retrofitted single-cylinder compression ignition engine

Up to 90% hydrogen energy fraction was achieved in a hydrogen diesel dual-fuel direct injection (H2DDI) light-duty single-cylinder compression ignition engine. An automotive-size inline single-cylinder diesel engine was modified to install an additional hydrogen direct injector. The engine was operated at a constant speed of 2000 revolutions per minute and fixed combustion phasing of ?10 crank angle degrees before top dead centre (°CA bTDC) while evaluating the power output, efficiency, combustion and engine-out emissions. A parametric study was conducted at an intermediate load with 20–90% hydrogen energy fraction and 180-0 °CA bTDC injection timing. High indicated mean effective pressure (IMEP) of up to 943 kPa and 57.2% indicated efficiency was achieved at 90% hydrogen energy fraction, at the expense of NO_x emissions. The hydrogen injection timing directly controls the mixture condition and combustion mode. Early hydrogen injection timings exhibited premixed combustion behaviour while late injection timings produced mixing-controlled combustion, with an intermediate point reached at 40 °CA bTDC hydrogen injection timing. At 90% hydrogen energy fraction, the earlier injection timing leads to higher IMEP/efficiency but the NO_x increase is inevitable due to enhanced premixed combustion. To keep the NO_x increase minimal and achieve the same combustion phasing of a diesel baseline, the 40 °CA bTDC hydrogen injection timing shows the best performance at which 85.9% CO₂ reduction and 13.3% IMEP/efficiency increase are achieved.     

Combustion analysis of a spark ignition engine fueled with gaseous blends containing hydrogen

This paper presents the combustion characteristics of a naturally aspirated spark ignition engine, intended for installation in vehicles, fueled with different hydrogen and methane blends. The experimental tests were carried out in a wide range of speeds at equivalence ratios of 1, 0.8 and 0.7 and at full load. The ignition timing was maintained for each speed, independently of the equivalence ratio and blend used as fuel. Four methane-hydrogen blends were used. In-cylinder pressure, mass fraction burned, heat released and cycle-by-cycle variations were analyzed as representative indicators of the combustion quality. It was observed that hydrogen enrichment of the blend improve combustion for the ignition timing chosen. This improvement is more appreciable at low speeds, because at high speeds hydrogen effect is attenuated by the high turbulence. Also, hydrogen addition allowed the extension of the LOL, enabling the engine to run stable in points where methane could not be tested. The main inconvenience detected was the high NO_x emissions measured, especially at stoichiometric conditions, due mainly to the increment in the combustion temperature that hydrogen produces.     

An experimental investigation on performance and emissions study with port injection using diesel as an ignition source for different EGR flow rates

Exhaust gas recirculation, EGR, is one of the most effective means of reducing NO_x emissions from IC engines and is widely used in order to meet the emission standards. In the present work, experimental investigation has been carried out to study the NO_x reduction characteristics by exhaust gas recirculation in a dual fueled engine using hydrogen and diesel. A single cylinder diesel engine was converted to operate on hydrogen-diesel dual fuel mode. Hydrogen was injected in intake port and diesel was injected directly inside the cylinder. The injection timing and injection duration of hydrogen were optimized initially based on the performance and emissions. It was observed that start of injection at 5° before gas exchange top dead center (BGTDC) and injection duration of 30° crank angle gives the best results. The flow rate of hydrogen was optimized as 7.5 lpm for the best start of injection and injection duration of hydrogen. Cold exhaust gas recirculation technique was adopted for the optimized injection parameter of hydrogen and flow rate. Maximum quantity of exhaust gases recycled during the test was 25% beyond this the combustion was not stable resulting in increase in smoke.     

The effect of fuel injection on NOx emissions and undesirable combustion for hydrogen-fuelled piston engines

In order to determine the potential of direct cylinder injection for hydrogen-fuelled engines, an experimental study was performed with an ASTM-CFR engine. Both the standard Otto head and the standard diesel head were used. Measurements were made of power output, thermal efficiency, and oxides of nitrogen emissions. The feasibility was investigated of a scheme in which injection of gaseous hydrogen starts late in the compression stroke, ignition occurs as soon as possible thereafter, and combustion rate is determined by injection rate. This scheme prevents undesirable combustion phenomena such as pre-ignition, high rates of cylinder pressure rise, and high amplitude pressure waves in the cylinder. Furthermore, it obviates flashback into the carburetor. The potential of hydrogen as a low pollution fuel was investigated by operating the Otto head engine on both hydrogen and indolene, and by comparing the resulting NO_x, emissions. Hydrogen yielded very low NO_x emissions provided the fuel-air equivalence ratio was less than 0.5, and provided the hydrogen and air were well mixed. For equivalence ratios greater than 0.5, hydrogen yielded NO_x emissions that were higher than those obtained with indolene. The timing of hydrogen injection was found to have a significant effect on NO_x emissions. With an unthrottled air intake and hydrogen injection at equivalence ratios between 0.3 and 0.8, indicated mean effective pressures ranged from 0.3 to 0.78 MPa. Corresponding indicated thermal efficiencies ranged from 43 to 31%. By decreasing the equivalence ratio to 0.1, the IMEP could be reduced to 0.07 MPa, thus providing an indicated load range of more than a factor of 10.     

An experimental investigation on DI diesel engine with hydrogen fuel

The internal combustion engines have already become an indispensable and integral part of our present day life style, particularly in the transportation and agricultural sectors [Nagalingam B. Properties of hydrogen. In: Proceedings of the summer school of hydrogen energy, IIT Madras, 1984]. Unfortunately the survival of these engines has, of late, been threatened due to the problems of fuel crisis and environmental pollution. Therefore, to sustain the present growth rate of civilization, a nondepletable, clean fuel must be expeditiously sought. Hydrogen exactly caters to the specified needs. Hydrogen, even though “renewable” and “clean burning”, does give rise to some undesirable combustion problems in an engine operation, such as backfire, pre-ignition, knocking and rapid rate of pressure rise [Srinivasa Rao P. Utilization of hydrogen in a dual fueled engine. In: Proceedings of the summer school of hydrogen energy, IIT Madras, 1984; Siebers DL. Hydrogen combustion under diesel engine conditions. Hydrogen Energy 1998;23:363–71]. The present investigation compares the performance and emission characteristics of a DI diesel engine with gaseous hydrogen as a fuel inducted by means of carburation technique and timed port injection technique (TPI) along with diesel as a source of ignition [Swain N, Design and testing of dedicated hydrogen-fueled engine. SAE 961077, 1996]. In the present study the specific energy consumption, NO_x emission and the exhaust gas temperature increased by 6%, 8% and 14%, respectively, and brake thermal efficiency and smoke level reduced by 5% and 8%, respectively, using carburation technique compared to baseline diesel. But in the TPI technique, the specific energy consumption, exhaust gas temperature and smoke level reduced by 15%, 45% and 18%, respectively. The brake thermal efficiency and NO_x increased by 17% and 34%, respectively, compared to baseline diesel. The emissions such as HC, CO, and CO₂ is very low in both carburation and TPI techniques compared baseline diesel.     

Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

NOx reduction and NO2 emission characteristics in rich-lean combustion of hydrogen

Hydrogen is a clean alternative to conventional hydrocarbon fuels, but it is very important to reduce the nitrogen oxides (NO_x) emissions generated by hydrogen combustion. The rich-lean combustion or staged combustion is known to reduce NO_x emissions from continuous combustion burners such as gas turbines and boilers, and NO_x reduction effects have been demonstrated for hydrocarbon fuels. The authors applied rich-lean combustion to a hydrogen gas turbine and showed its NO_x reduction effect in previous research. The present study focused on experimental measurements of NO and NO₂ emissions from a coaxial rich-lean burner fueled with hydrogen. The results were compared with diffusion combustion and methane rich-lean combustion. Significant reductions in NO and NO₂ were achieved with rich-lean combustion. The NO and NO₂ reduction effects by rich-lean combustion relative to conventional diffusion combustion were higher with hydrogen than with methane.     

Combustion and emission characteristics of an Acetone-Butanol-Ethanol (ABE) spark ignition engine with hydrogen direct injection

Butanol could reduce emissions and alleviate the energy crisis as a bio-fuel used on engines, but the production cost problem limits the application of butanol. During the butanol production, ABE (Acetone-Butanol-Ethanol) is a critical intermediate product. Many studies researched the direct application of ABE on engines instead of butanol to solve the production cost problem of butanol. ABE has the defects of large ignition energy and vaporization heat. Hydrogen is a gaseous fuel with small ignition energy and high flame temperature. In this research, ABE port injection combines with hydrogen direct injection, forming a stratified state of the hydrogen-rich mixture around the spark plug. The engine speed is 1500 rpm, and λ is 1. Five αH₂ (hydrogen blending fractions: 0, 5%, 10%, 15%, 20%) and five spark timings (5°, 10°, 15°, 20°, 25° CA BTDC) are studied to observe the effects of them on combustion and emissions of the test engine. The results show that hydrogen addition increases the maximum cylinder pressure and maximum heat release rate, increases the maximum cylinder temperature and IMEP, but the exhaust temperature decreases. The flame development period and flame propagation period shorten after adding hydrogen. Hydrogen addition improves HC and CO emissions but increases NO_x emissions. Particle emissions decrease distinctly after hydrogen addition. Hydrogen changes the combustion properties of ABE and improves the test engine's power and emissions. The combustion in the cylinder becomes better with the increase of αH₂, but a further increase in αH₂ beyond 5% brings minor improvements on combustion.     

Hydrogen dual-fuelling of compression ignition engines with emulsified biodiesel as pilot fuel

Dual-fuel compression ignition (CI) engine operation with hydrogen is a promising method of using hydrogen gas in CI engines via high-cetane pilot fuel ignition. However, hydrogen dual-fuel operation with neat pilot fuels typically produce: high NO_x emissions; and high combustion chamber pressure rise rates (leading to increased “Diesel knock” tendencies). While water-in-fuel emulsions have been used during normal CI engine operation to cool the charge and slow combustion rates in an effort to reduce NO_x emissions, these water-in-fuel emulsions have not been tested as pilot fuels during hydrogen dual-fuel combustion. In this work two water-in-biodiesel emulsions are tested as pilot fuels during hydrogen dual-fuel operation. Hydrogen dual-fuel operation generally produces at best comparable thermal efficiencies compared with normal CI engine operation, while the emulsified biodiesel pilot fuels generally increase thermal efficiencies when compared with the neat biodiesel pilot fuel during dual-fuel operation. There is also a clear reduction in NO_x emissions with emulsified pilot fuel use compared with the neat pilot fuel. The thermal efficiency increase is more apparent at higher engine speeds, while the NO_x reduction is more apparent at lower speeds. This is due to two conflicting effects (exclusive to emulsified pilot fuel) that occur in tandem. The first is the cooling effect of water vapourisation on the charge, while the second is the microexplosion phenomenon which enhances fuel-air mixing. The NO_x emission reduction is due to the emulsified pilot fuel lowering pressure rise rates compared with the neat pilot fuel, while the efficiency increase is due to a more homogeneous charge resulting from the violent microexplosion of the emulsified pilot fuel. Smoke, CO, HC and CO₂ emissions remain comparable to neat pilot fuel tests. Overall, emulsified pilot fuels can reduce NO_x emissions and increase thermal efficiencies, however not at the same instance and under different operating conditions. The general trends of reduced power output, reduced CO₂ and increased water vapour emission during hydrogen dual-fuel operation (with neat pilot fuels) are also maintained.     

The effects of injection timing on NOx emissions of a low heat rejection indirect diesel injection engine

Higher NO_x is one of the major problems to be overcomed in a low heat rejection (LHR) diesel engine as insulation leads to an increase in combustion temperature about 200–250 °C compared to an identical standard (STD) diesel engine. High combustion temperatures alter optimum injection timing of a LHR engine. With the proper adjustment of the injection timing, it is possible to partially offset the adverse effect of insulation on heat release rate and hence to obtain improved performance and lower NO_x. However, the injection timing and brake specific fuel consumption (BSFC) trade-off must be considered together in performance and NO_x emission point of view. In this study, optimum injection timing was found with 4 crank angle (34° CA) retarded before top dead centre (BTDC) in LHR diesel engine in comparison to that of STD diesel engine (38° CA BTDC). When the LHR engine was operated with the injection timing of the 38 crank angle, which is the optimum value of the STD engine, it was shown that NO_x emission increased about 15%. However, when the injection timing was retarded to 34° CA in the LHR case, it was observed a decrease on the NO_x emissions with about 40% and the brake specific fuel consumption (BSFC) with about 6% compared to that of the STD case. Thus, by retarding the injection timing, an additional 1.5% saving in fuel consumption was obtained.     

The effects of fuel-injection timing at medium injection pressure on the engine characteristics and emissions of a CNG-DI engine fueled by a small amount of hydrogen in CNG

The experiments to determine the effect of fuel-injection timings on engine characteristics and emissions of a DI engine fueled with NG-hydrogen blends (0%, 3%, 5% and 8%) at various engine speeds were conducted. Three injection timings namely 120°, 180° and 300° CA BTDC with a wide open throttle at relative air-fuel ratio, λ = 1.0 were selected. The ignition advance angle was fixed at 30° CA BTDC, while the injection pressure was fixed at 1.4 MPa for all the cases. The tests were firstly performed at low engine speed of 2000 rpm to determine the engine characteristics and emissions. The results showed that the engine performance (e.g. Brake Torque, Brake Power and BMEP), the cylinder pressure and the heat release have the highest values at the injection timing of 180° CA BTDC, followed by the 300° CA BTDC and the 120° CA BTDC. The NO_x emission was found to be highest at the injection timing of 180° CA BTDC. The THC and CO emissions were found to decrease while the CO₂ emission increased with the advancement in the injection timing. The addition of a small amount of hydrogen to the natural gas was found to increase the engine performance, enhance combustion and reduce emissions for any selected injection timings. Secondly, the tests were carried out at variable engine speeds (i.e. 2000 rpm-4000 rpm) in order to further investigate the engine performance. The injection timings of 180° and 300° CA BTDC with CNG-H₂ blends were only selected for comparisons. The injection timing of the 300° CA BTDC was discovered to yield better engine performance as compared to the 180° CA BTDC injection timing after a cutoff engine speed of approximately 2500 rpm.     

Emission and performance estimation in hydrogen injection strategies on diesel engines

Recently, the increasing demand for energy requires the use of alternative fuels, especially in fossil fueled power systems. As a promising alternative fuel for next-generation diesel engines that utilize fossil fuel, hydrogen fuel is one step ahead due to its positive properties. In this study, the effects of hydrogen on the performance of a diesel engine have been numerically investigated with respect to different injection ratios and timings. The numerical results of the study for 25% load conditions on a single-cylinder, four-stroke diesel engine have been validated against experimental data taken from literature and good agreement has been observed for pressure results. Emission parameters such as NO_x, CO and performance parameters such as cylinder temperature, pressure, power, thermal efficiency and IMEP are presented comparatively.The results of numerical analyses show that the maximum pressure, temperature and heat release rate are observed with injection ratio of H15 and early injection timing (20° CA BTDC). Besides that, engine power, thermal efficiency and IMEP are greatly improved with increasing injection ratio and early injection timing. Although combustion chamber performance parameters improve with rising the hydrogen injection ratio, higher NO_x emissions have also been detected as a negative side effect. Furthermore, while early injection timing increases diesel engine performance, it also causes an increase in NO_x emissions. Therefore, precise determination of injection timing together with the optimum amount of hydrogen has revealed that it brings crucial improvement in engine performance and emissions.     

Backfire prediction in a manifold injection hydrogen internal combustion engine

Hydrogen internal combustion engine (H2ICE) easily occur inlet manifold backfire and other abnormal combustion phenomena because of the low ignition energy, wide flammability range and rapid combustion speed of hydrogen. In this paper, the effect of injection timing on mixture formation in a manifold injection H2ICE was studied in various engine speed and equivalence ratio by CFD simulation. It was concluded that H2ICE of manifold injection have an limited injection end timing in order to prevent backfire in the inlet manifold. Finally, the limit of injection end timing of the H2ICE was proposed and validated by engine experiment.     

Hydrogen assisted diesel combustion

Hydrogen assisted diesel combustion was investigated on a DDC/VM Motori 2.5L, 4-cylinder, turbocharged, common rail, direct injection light-duty diesel engine, with a focus on exhaust emissions. Hydrogen was substituted for diesel fuel on an energy basis of 0%, 2.5%, 5%, 7.5%, 10% and 15% by aspiration of hydrogen into the engine's intake air. Four speed and load conditions were investigated (1800 rpm at 25% and 75% of maximum output and 3600 rpm at 25% and 75% of maximum output). A significant retarding of injection timing by the engine's electronic control unit (ECU) was observed during the increased aspiration of hydrogen. The retarding of injection timing resulted in significant NO_X emission reductions, however, the same emission reductions were achieved without aspirated hydrogen by manually retarding the injection timing. Subsequently, hydrogen assisted diesel combustion was examined, with the pilot and main injection timings locked, to study the effects caused directly by hydrogen addition. Hydrogen assisted diesel combustion resulted in a modest increase of NO_X emissions and a shift in NO/NO₂ ratio in which NO emissions decreased and NO₂ emissions increased, with NO₂ becoming the dominant NO_X component in some combustion modes. Computational fluid dynamics analysis (CFD) of the hydrogen assisted diesel combustion process captured this trend and reproduced the experimentally observed trends of hydrogen's effect on the composition of NO_X for some operating conditions. A model that explicitly accounts for turbulence–chemistry interactions using a transported probability density function (PDF) method was better able to reproduce the experimental trends, compared to a model that ignores the influence of turbulent fluctuations on mean chemical production rates, although the importance of the fluctuations is not as strong as has been reported in some other recent modeling studies. The CFD results confirm that temperature changes alone are not sufficient to explain the observed reduction in NO and increase in NO₂ with increasing H₂. The CFD results are consistent with the hypothesis that in-cylinder HO₂ levels increase with increasing hydrogen, and that the increase in HO₂ enhances the conversion of NO to NO₂. Increased aspiration of hydrogen resulted in PM, and HC emissions which were combustion mode dependent. Predominantly, CO and CO₂ decreased with the increase of hydrogen. The aspiration of hydrogen into the engine modestly decreased fuel economy due to reduced volumetric efficiency from the displacement of air in the cylinder by hydrogen.     

Performance and emission studies on port injection of hydrogen with varied flow rates with Diesel as an ignition source

Automobiles are one of the major sources of air pollution in the environment. In addition CO₂ emission, a product of complete combustion also has become a serious issue due to global warming effect. Hence the search for cleaner alternative fuels has become mandatory. Hydrogen is expected to be one of the most important fuels in the near future for solving the problems of air pollution and greenhouse gas problems (carbon dioxide), thereby protecting the environment. Hence in the present work, an experimental investigation has been carried out using hydrogen in the dual fuel mode in a Diesel engine system. In the study, a Diesel engine was converted into a dual fuel engine and hydrogen fuel was injected into the intake port while Diesel was injected directly inside the combustion chamber during the compression stroke. Diesel injected inside the combustion chamber will undergo combustion first which in-turn would ignite the hydrogen that will also assist the Diesel combustion. Using electronic control unit (ECU), the injection timings and injection durations were varied for hydrogen injection while for Diesel the injection timing was 23° crank angle (CA) before injection top dead centre (BITDC). Based on the performance, combustion and emission characteristics, the optimized injection timing was found to be 5° CA before gas exchange top dead centre (BGTDC) with injection duration of 30° CA for hydrogen Diesel dual fuel operation. The optimum hydrogen flow rate was found to be 7.5 lpm. Results indicate that the brake thermal efficiency in hydrogen Diesel dual fuel operation increases by 15% compared to Diesel fuel at 75% load. The NO_X emissions were higher by 1–2% in dual fuel operation at full load compared to Diesel. Smoke emissions are lower in the entire load spectra due to the absence of carbon in hydrogen fuel. The carbon monoxide (CO), carbon dioxide (CO₂) emissions were lesser in hydrogen Diesel dual fuel operation compared to Diesel. The use of hydrogen in the dual fuel mode in a Diesel engine improves the performance and reduces the exhaust emissions from the engine except for HC and NO_X emissions.     

Performance and combustion characteristics of a direct injection SI hydrogen engine

Hydrogen with low spark-energy requirement, wide flammability range and high burning velocity is an important candidate for being used as fuel in spark-ignition engines. It also offers CO₂ and HC free combustion and lean operation resulting in lower _NOx${\mathrm{NO}}_x$ emissions. However, well examined external mixing of hydrogen with intake air causes backfire and knock especially at higher engine loads. In addition, low heating value per unit of volume of hydrogen limits the maximum output power. In this study, attention was paid to full usage of hydrogen advantage employing internal mixing method. Hydrogen was directly injected into cylinder of a single-cylinder test engine using a high-pressure gas injector and effects of injection timing and spark timing on engine performance and _NOx${\mathrm{NO}}_x$ emission were investigated under wide engine loads. The results indicate that direct injection of hydrogen prevents backfire, and that high thermal efficiency and output power can be achieved by hydrogen injection during late compression stroke. Moreover, by further optimization of the injection timing for each engine load, _NOx${\mathrm{NO}}_x$ emission can be reduced under the high engine output conditions.     

Effect of hydrogen direct injection on natural gas/hydrogen engine performance under high compression-ratio conditions

In traffic transportation, the use of low-carbon fuels is the key to being carbon-neutral. Hydrogen-enhanced natural gas gets more and more attention, but practical engines fueled with it often suffer from low engine power output. In this study, the inner mechanism of hydrogen direct injection on methane combustion was optically studied based on a dual-fuel supply system. Simultaneous pressure acquisition and high-speed direct photography were used to analyze engine performance and flame characteristics. The results show that lean combustion can improve methane engine's thermal efficiency, but is limited by cyclic variations under high excess air coefficient conditions. Hydrogen addition mainly acts as an ignition promoter for methane lean combustion, as a result, the lean combustion limit and thermal efficiency can be improved. As for hydrogen injection timing, late injection can increase the in-cylinder turbulence intensity but also the inhomogeneity, so a suitable injection timing is needed for improving the engine's performance. Besides, late hydrogen injection is more effective under lean conditions because of the reduced mixture inhomogeneity. The current study shall give some insights into the controlling strategies for natural gas/hydrogen engines.     

Comparison of the effects of EGR and lean burn on an SI engine fueled by hydrogen-enriched low calorific gas

A naturally aspirated spark ignition (SI) engine fueled by hydrogen-blended low calorific gas (LCG) was tested in both exhaust gas recirculation (EGR) and lean burn modes. The “dilution ratio” was introduced to compare their effects on engine performance and emissions under identical levels of dilution. LCG composed of 40% natural gas and 60% nitrogen was used as a main fuel, and hydrogen was blended with the LCG in volumes ranging from 0 to 20%. The engine test results demonstrated that EGR operations at stoichiometry showed a narrower dilution range, inferior combustion characteristics, lower brake thermal efficiency, faster nitrogen oxides (NO_x) suppression, and higher total hydrocarbon (THC) emissions for all hydrogen blending rates compared to lean burn. These trends were mainly due to the increased oxygen deficiency as a result of using EGR in LCG/air mixtures. Hydrogen enrichment of the LCG improved combustion stability and reduced THC emissions while increasing NO_x. In terms of efficiency, hydrogen addition induced a competition between combustion enhancement and increases in the cooling loss, so that the peak thermal efficiency occurred at 10% H₂ with excess air ratio of 1.5. The engine test results also indicated that a close-to-linear NO_x-efficiency relationship occurred for all hydrogen blending rates in both operations as long as stable combustion was achieved. NO_x versus combustion duration analysis showed that adding H₂ reduced combustion duration while maintaining the same level of NO_x. The methane fraction contained in the THC emissions decreased slightly with an increase in hydrogen enrichment at low EGR or excess air dilution ratios, but this tendency was diminished at higher dilution ratios because of the combined dilution effects from the inert gas in the LCG and the diluents (EGR or excess air).     

A simulation of the combustion of hydrogen in HCCI engines using a 3D model with detailed chemical kinetics

The influence of changes in the swirl velocity of the intake mixture on the combustion processes within a homogeneous charge compression ignition (HCCI) engine fueled with hydrogen were investigated analytically. A turbulent transient 3D predictive computational model which was developed and applied to the HCCI engine combustion system, incorporated detailed chemical kinetics for the oxidation of hydrogen. The effects of changes in the initial intake swirl, temperature and pressure, engine speed and compression and equivalence ratios on the combustion characteristics of a hydrogen fuelled HCCI engine were also examined. It is shown that an increase in the initial flow swirl ratio or speed lengthens the delay period for autoignition and extends the combustion period while reducing NO_x emissions. There are optimum values of the initial swirl ratio and engine speed for a certain mixture intake temperature, pressure, compression and equivalence ratios operational conditions that can achieve high thermal efficiencies and low NO_x emissions while reducing the tendency to knock     

An experimental investigation on manifold‐injected hydrogen as a dual fuel for diesel engine system with different injection duration

Stringent emission norms and rapid depletion of petroleum resources have resulted in a continuous effort to search for alternative fuels. Hydrogen is one of the best alternatives for conventional fuels. Hydrogen has both the benefits and limitation to be used as a fuel in an automotive engine system. In the present investigation, hydrogen was injected into the intake manifold by using a hydrogen gas injector and diesel was introduced in the conventional, mode which also acts as an ignition source for hydrogen combustion. The flow rate of hydrogen was set at 5.5 l min^?1 at all the load conditions. The injection timing was kept constant at top dead center (TDC) and injection duration was adjusted to find the optimized injection condition. Experiments were conducted on a single cylinder, four stroke, water‐cooled, direct injection diesel engine coupled to an electrical generator. At 75% load the maximum brake thermal efficiency for hydrogen operation at injection timing of TDC and with injection duration of 30°CA is 25.66% compared with 21.59% for diesel. The oxides of nitrogen (NO_X) emission are 21.7 g kWh^?1 for hydrogen compared with diesel of 17.9 g k Wh^?1. Smoke emissions reduced to 1 Bosch smoke number (BSN) in hydrogen compared with diesel of 2.2 BSN. Hydrogen operation in the dual fuel mode with diesel exhibits a better performance and reduction in emissions compared with diesel in the entire load spectra. Copyright © 2009 John Wiley & Sons, Ltd.