Phase change and heat transfer characteristics of a eutectic mixture of palmitic and stearic acids as PCM in a latent heat storage system

The phase change and heat transfer characteristics of a eutectic mixture of palmitic and stearic acids as phase change material (PCM) during the melting and solidification processes were determined experimentally in a vertical two concentric pipes energy storage system. This study deals with three important subjects. First is determination of the eutectic composition ratio of the palmitic acid (PA) and stearic acid (SA) binary system and measurement of its thermophysical properties by differential scanning calorimetry (DSC). Second is establishment of the phase transition characteristics of the mixture, such as the total melting and solidification temperatures and times, the heat transfer modes in the melted and solidified PCM and the effect of Reynolds and Stefan numbers as initial heat transfer fluid (HTF) conditions on the phase transition behaviors. Third is calculation of the heat transfer coefficients between the outside wall of the HTF pipe and the PCM, the heat recovery rates and heat fractions during the phase change processes of the mixture and also discussion of the effect of the inlet HTF parameters on these characteristics. The DSC results showed that the PA–SA binary system in the mixture ratio of 64.2:35.8 wt% forms a eutectic, which melts at 52.3 °C and has a latent heat of 181.7 J g⁻¹, and thus, these properties make it a suitable PCM for passive solar space heating and domestic water heating applications with respect to climate conditions. The experimental results also indicated that the eutectic mixture of PA–SA encapsulated in the annulus of concentric double pipes has good phase change and heat transfer characteristics during the melting and solidification processes, and it is an attractive candidate as a potential PCM for heat storage in latent heat thermal energy storage systems.     

Experimental research on thermal characteristics of PCM thermal energy storage units

To explore thermal management integration in electric vehicles (EVs), a phase change materials (PCMs) thermal energy storage unit using flat tubes and corrugated fins is designed. The investigation focuses on the thermal characteristics of the PCM unit, such as the temperature variation, heat capacity, and heat transfer time, etc. Meanwhile, the heat storage and release process will be influenced by different inlet temperature, liquid flow rate, melting point of the PCM, and the combination order of the units. Under the same inlet temperature and flow rate condition, the PCM unit with higher melting point enters the latent heat storage stage slowly and enters the phase change melting release stage quickly. Furthermore, the heat storage and release rates increase with increasing liquid flow rates, but the effects are diminishing in the middle and later periods. The multiple PCM units with different melting temperatures are cascaded to help recycle low-grade heat energy with different temperature classes and exhibit well heat storage and release rates.     

Lauric and myristic acids eutectic mixture as phase change material for low‐temperature heating applications

Lauric acid (m.p.: 42.6°C) and myristic acid (m.p.: 52.2°C) are phase change materials (PCM) having quite high melting points which can limit their use in low‐temperature solar applications such as solar space heating and greenhouse heating. However, their melting temperatures can be tailored to appropriate value by preparing a eutectic mixture of lauric acid (LA) and myristic acid (MA). In the present study, the thermal analysis based on differential scanning calorimetry (DSC) technique shows that the mixture of 66.0 wt% LA forms a eutectic mixture having melting temperature of 34.2°C and the latent heat of fusion of 166.8 J g^?1. This study also considers the experimental establishment of thermal characteristics of the eutectic PCM in a vertical concentric pipe‐in‐pipe heat storage system. Thermal performance of the PCM was evaluated with respect to the effect of inlet temperature and mass flow rate of the heat transfer fluid on those characteristics during the heat charging and discharging processes. The DSC thermal analysis and the experimental results indicate that the LA–MA eutectic PCM can be potential material for low‐temperature solar energy storage applications in terms of its thermo‐physical and thermal characteristics. Copyright © 2005 John Wiley & Sons, Ltd.     

Thermal performance of a eutectic mixture of lauric and stearic acids as PCM encapsulated in the annulus of two concentric pipes

Thermal performance characteristics of a eutectic mixture of lauric and stearic acids as phase change material (PCM) during the melting and solidification processes were determined experimentally in a vertical two concentric pipe-energy storage system. This study deals with three important subjects: The first one is to determine the eutectic composition ratio of the lauric acid (LA) and stearic acid (SA) binary system, and to measure its thermophysical properties by DSC. The second one is to establish the thermal characteristics of the mixture such as total melting and solidification times, the heat transfer modes in melted and solidified PCM, and the effect of Reynolds and Stefan numbers as inlet heat transfer fluid (HTF) conditions on the phase transition behaviors. The final one includes the calculations of the heat transfer coefficients between the outside wall of the HTF pipe and the PCM, and heat fractions during the melting and solidification processes of the mixture, and also the discussion of the effect of inlet HTF parameters on these characteristics. The LA–SA binary system in the mixture ratio of 75.5:24.5 wt % forms a eutectic, which melts at 37°C and has a latent heat of 182.7 J g⁻¹, and, thus, these properties make it an attractive phase change material used for passive solar space heating applications such as building and greenhouse heating with respect to the climate conditions. The experimental results indicated that the mixture encapsulated in the annulus of two concentric pipes has good thermal and heat transfer characteristics during the melting and solidification processes, and it has potential for heat storage in passive solar space heating systems.     

Lauric and palmitic acids eutectic mixture as latent heat storage material for low temperature heating applications

Palmitic acid (PA, 59.8 °C) and lauric acid (LA, 42.6 °C) are phase change materials (PCM) having quite high melting temperatures which can limit their use in low temperature solar applications such as solar space heating and greenhouse heating. However, their melting temperatures can be tailored to appropriate value by preparing a eutectic mixture of the lauric and the palmitic acids. In the present study, the thermal analysis based on differential scanning calorimetry (DSC) technique shows that the mixture of 69.0 wt% LA and 31 wt% PA forms a eutectic mixture having melting temperature of 35.2 °C and the latent heat of fusion of 166.3 J g⁻¹. This study also considers the experimental determination of the thermal characteristics of the eutectic mixture during the heat charging and discharging processes. Radial and axial temperature distribution, heat transfer coefficient between the heat transfer fluid (HTF) pipe and the PCM, heat recovery rate and heat charging and discharging fractions were experimentally established employing a vertical concentric pipe-in-pipe energy storage system. The changes of these characteristics were evaluated with respect to the effect of inlet HTF temperature and mass flow rate. The DSC thermal analysis and the experimental results indicate that the LA–PA eutectic mixture can be a potential material for low temperature thermal energy storage applications in terms of its thermo-physical and thermal characteristics.     

Heat transfer intensification in horizontal shell and tube latent heat storage unit

Employment of latent heat storage unit (LHSU) utilizing phase change material (PCM) in a substantial scale is constrained by the poor thermal conductivity of PCMs. Future utilization of LHSU will therefore to a great extent rely on the heat transfer intensification techniques. Present research is on enhancement techniques in which heat transfer mechanism is altered without altering the mass of PCM and heat transfer surface area. The intensification mechanisms considered in the present research include imparting eccentricity to heat transfer fluid (HTF) pipe, imparting rotation to the LHSU and providing multi HTF tube. Numerical investigations are reported here towards comparative evaluation of the thermal characteristics associated with such intensification mechanisms for horizontal LHSU. In the present study stearic acid (melting point 55.7–56.6?°C) is used as PCM and water is used as HTF. Results infer that all the three mechanisms offer quicker melting rate. For the geometric configuration of LHSU considered in the present research, a reduction in melting time of 47.75% is evaluated for rotating LHSU. The rate of energy storage is higher for both eccentric and rotating LHSU. Solidification process is however not accelerated by such techniques. On the contrary, eccentric and multi HTF tube LHSU takes more time for solidification.     

Heat Transfer Enhancement for PCM Thermal Energy Storage in Triplex Tube Heat Exchanger

Thermal energy storage is critical for reducing the discrepancy between energy supply and energy demand, as well as for improving the efficiency of solar thermal energy systems. Among the different types of thermal energy storage, phase-change materials (PCM) thermal energy storage has gained significant attention recently because of its high energy density per unit mass/volume at nearly constant temperature. This study experimentally investigates the using of a triplex tube heat exchanger (TTHX) with PCM in the middle tube as the thermal energy storage to power a liquid desiccant air-conditioning system. Four longitudinal fins were welded to each of the inner and middle tubes as a heat transfer enhancement in the TTHX to improve the thermal performance of the thermal energy storage. The average temperature of the PCM during the melting process in the TTHX with and without fins was compared. The PCM temperature gradients in the angular direction were analyzed to study the effect of the natural convection in the melting process of the thermal storage. The energy storage efficiency of the TTHX was determined. Results indicated that there was a considerable enhancement in the melting rate by using fins in the TTHX thermal storage. The PCM melting time is reduced to 86% by increasing of the inlet heat transfer fluid. The average heat storage efficiency calculated from experimental data for all the PCMs is 71.8%, meaning that 28.2% of the heat actually was lost.     

Thermal energy storage system using stearic acid as a phase change material

The thermal performance and phase change stability of stearic acid as a latent heat energy storage material has been studied experimentally. The thermal performance and heat transfer characteristics of the stearic acid were tested and compared with other studies given in the literature. In the present study, parameters such as transition times, temperature range and propagation of the solid–liquid interface as well as the effect of the heat flow rate on the phase change stability of stearic acid as a phase change material (PCM) were studied. The experimental results showed that the melting stability of the PCM is better in the radial direction than in the axial direction. The variation in the melting and solidification parameters of the PCM with the change of inlet water temperature is also studied. We observed that while the heat exchanger tube is in the horizontal position, the PCM has more effective and steady phase change characteristics than in the vertical position. The heat storage capacity of the container (PCM tube) is not as good as we expected in this study and the average heat storage efficiency (or heat exchanger effectiveness) is 50.3%. This indicates that 49.7% of the heat is actually lost somewhere.     

Thermal and heat transfer characteristics in a latent heat storage system using lauric acid

The thermal and heat transfer characteristics of lauric acid during the melting and solidification processes were determined experimentally in a vertical double pipe energy storage system. In this study, three important subjects were addressed. The first one is temperature distributions and temporal temperature variations in the radial and axial distances in the phase change material (PCM) during phase change processes. The second one is the thermal characteristics of the lauric acid, which include total melting and total solidification times, the nature of heat transfer in melted and solidified PCM and the effect of Reynolds and Stefan numbers as inlet heat transfer fluid (HTF) conditions on the phase transition parameters. The final one is to calculate the heat transfer coefficient and the heat flow rate and also discuss the role of Reynolds and Stefan numbers on the heat transfer parameters. The experimental results proved that the PCM melts and solidifies congruently, and the melting and solidification front moved from the outer wall of the HTF pipe (HTFP) to the inner wall of the PCM container in radial distances as the melting front moved from the top to the bottom of the PCM container in axial distances. However, it was difficult to establish the solidification proceeding at the axial distances in the PCM. Though natural convection in the liquid phase played a dominant role during the melting process due to buoyancy effects, the solidification process was controlled by conduction heat transfer, and it was slowed by the conduction thermal resistance through the solidified layer. The results also indicated that the average heat transfer coefficient and the heat flow rate were affected by varying the Reynolds and Stefan numbers more during the melting process than during the solidification process due to the natural convection effect during the melting process.     

Experimental and numerical investigation of the melting process and heat transfer characteristics of multiple phase change materials

The melting and heat transfer characteristics of multiple phase change materials (PCMs) are investigated both experimentally and numerically. Multiple PCMs, which consist of three PCMs with different melting points, are filled into a rectangle-shaped cavity to serve as heat storage unit. One side of the cavity is set as heating wall. The melting rate of multiple PCMs was recorded experimentally and compared with that of single PCM for different heating temperatures. A two-dimensional mathematical model to describe the phase change heat transfer was developed and verified experimentally. The properties of multiple PCMs, including the effect of the melting point difference (combined type), thermal conductivity, and latent heat, on the heat transfer performance of the PCM were analyzed numerically. The results show that, the melting time decreases before it increases, with an increasing melting point difference for the multiple PCMs. In addition, the melting point decreases with increasing distance from the heating wall. Most of these types of multiple PCMs melt faster than the single PCM, and the multiple PCMs, with the melting point arranged as 322 K/313 K/304 K, has the shortest melting time in this study. The melting rate of the multiple PCMs, 322 K/313 K/304 K, accelerates faster than for the single PCM as the thermal conductivity, latent heat, and heating wall temperature increase. Finally, generalized results are obtained using a dimensionless analysis for both single and multiple PCMs.     

Thermal Energy Storage Performance of Fatty Acids as a Phase Change Material

Thermal energy storage performance of fatty acids and a eutectic mixture as phase change materials (PCMs) has been investigated experimentally. The selected PCMs for this study were palmitic acid, myristic acid, stearic acid, and a mixture of stearic and myristic acids in eutectic combination ratio of 65.7 wt% myristic acid and 34.3 wt% stearic acid. The PCMs have a melting temperature range of 50.0°C to 61.20°C and a latent heat range of 162.0 J/g to 204.5 J/g. The inlet temperature and the mass flow rate of heat transfer fluid (HTF) were selected as experimental parameters to test the thermal energy storage performance of the PCMs. The transition times, temperature range, propagation of the solid-liquid interface, as well as heat flow rate characteristics of the employed cylindrical tube storage system were studied at varied experimental parameters. The experimental results show that the melting front moves to inward in the radial directions as well as in the axial directions from the top toward to the bottom of the PCM tube. It was observed that the convection heat transfer in the liquid phase plays an important role in the melting process. The changes in the studied HTF parameters have more effect on the melting processes than the solidification processes of the PCMs. The average heat storage efficiency calculated from data for all the PCMs is 51.5%, meaning that 48.5% of the heat actually was lost somewhere.     

High temperature latent heat thermal energy storage using heat pipes

A thermal network model is developed and used to analyze heat transfer in a high temperature latent heat thermal energy storage unit for solar thermal electricity generation. Specifically, the benefits of inserting multiple heat pipes between a heat transfer fluid and a phase change material (PCM) are of interest. Two storage configurations are considered; one with PCM surrounding a tube that conveys the heat transfer fluid, and the second with the PCM contained within a tube over which the heat transfer fluid flows. Both melting and solidification are simulated. It is demonstrated that adding heat pipes enhances thermal performance, which is quantified in terms of dimensionless heat pipe effectiveness.     

Heat transfer enhancement of fatty acids when used as PCMs in thermal energy storage

Phase change materials (PCM) used in latent heat storage systems usually have very low thermal conductivities. This is a major drawback in maintaining the required heat exchange rate between PCM and heat transfer fluid. This paper investigates the enhancement of the heat transfer between PCM and heat transfer fluid, using high thermal conductivity as additives like stainless steel pieces, copper pieces and graphite–PCM composite material. In the experiments, palmitic–lauric acid (80:20) (PL) and stearic–myristic acid (80:20) (SM) were used as PCMs. Test results show that heat transfer enhancement of copper pieces was better at 0.05 Ls^?1 flow rate compared to 0.025 Ls^?1. Using copper as an additive increased the heat transfer rate 1.7 times for melting and 3.8 times for freezing when flow rate was 0.050 Ls^?1. Decreasing the flow rate from 0.050 to 0.025 Ls^?1, increased the melting times 1.3 times and freezing times 1.8 times, decreasing heat transfer rates accordingly. The best result of heat transfer enhancement was observed for the PCM–graphite composite. However, changing the flow rate did not affect the heat transfer rate when graphite was used as additive. Copyright © 2007 John Wiley & Sons, Ltd.     

石墨泡沫/共晶盐复合相变材料制备

选择KNO3/NaNO3二元体系按照质量比4∶6制备共晶盐,对共晶盐进行了熔点及熔化潜热的测量;将石墨泡沫这一新型材料作为强化基体,共晶盐作为相变材料（PCM）,采用熔融浸渗法制备了适用于太阳能热发电系统储能装置的石墨泡沫/共晶盐复合相变材料。采用扫描电镜对复合相变材料表面的微观结构进行了表征,并对其熔点、潜热、等效导热系数等热物性参数进行了测试。结果表明：共晶盐与石墨泡沫复合效果比较理想;复合前后共晶盐的熔点和潜热几乎没有发生变化;复合相变材料的等效导热系数得到了显著提升,石墨泡沫对相变材料起到了导热强化作用,满足高温蓄热的要求。     

Thermal performance of myristic acid as a phase change material for energy storage application

Thermal performance and phase change stability of myristic acid as a latent heat energy storage material has been studied experimentally. In the experimental study, the thermal performance and heat transfer characteristics of the myristic acid were tested and compared with other studies given in the literature. In the present study is included some parameters such as transition times, temperature range, and propagation of the solid–liquid interface as well as heat flow rate effect on the phase change stability of myristic acid as a phase change material (PCM). The experimental results showed that the melting stability of the PCM is better in the radial direction than the axial direction. The variety of the melting and solidification parameters of the PCM with the change of inlet water temperature is also studied. The results show that the better stability of the myristic acid was accomplished at low inlet water temperature compared with the obtained results at high inlet water temperature. We also observed that while the heat exchanger tube is in the horizontal position, the PCM has more effective and steady phase change characteristics than in the vertical position. The heat storage capacity of the container (PCM tube) is not as good as we expected in this study and the average heat storage efficiency (or heat exchanger effectiveness) is 54%. It means that 46% of the heat acrually lost somewhere.     

水平管壳式相变蓄热装置的强化传热研究

基于焓法模型对水平管壳式相变蓄热装置热性能的增强进行研究,首先分析蓄热过程中传统管壳式装置内材料的传热及流动机理;然后引入椭圆元素并对比椭圆内管及外壳的强化传热效果;最后对热源温度、相变材料导热系数及初始温度对装置热性能的作用规律进行探讨。结果显示,椭圆外壳的强化传热效果优于内管,同等条件下,长短轴之比为2的椭圆外壳可使蓄热时间缩短53.5%。热源温度升高,椭圆外壳的强化传热效果进一步增强,相变材料的导热系数及初始温度对装置热性能的影响较小。     

Capric-myristic acid/vermiculite composite as form-stable phase change material for thermal energy storage

Phase change materials (PCMs) can be incorporated with building materials to obtain novel form-stable composite PCM which has effective energy storage performance in latent heat thermal energy storage (LHTES) systems. In this study, capric acid (CA)-myristic acid (MA) eutectic mixture/vermiculite (VMT) composite was prepared as a novel form-stable PCM using vacuum impregnation method. The composite PCM was characterized using scanning electron microscope (SEM) and Fourier transformation infrared (FT-IR) analysis technique. Thermal properties and thermal reliability of the composite PCM were determined by differential scanning calorimetry (DSC) analysis. The CA-MA eutectic mixture could be retained by 20 wt% into pores of the VMT without melted PCM seepage from the composite and therefore, this mixture was described as form-stable composite PCM. Thermal cycling test showed that the form-stable composite PCM has good thermal reliability and chemical stability although it was subjected to 3000 melting/freezing cycling. Thermal conductivity of the form-stable CA-MA/VMT composite PCM was increased by about 85% by introducing 2 wt% expanded graphite (EG) into the composite. The increase in thermal conductivity was confirmed by comparison of the melting and freezing times of the CA-MA/VMT composite with that of CA-MA/VMT/EG composite. The form-stable PCM including EG can be used as energy absorbing building material such as lightweight aggregate for plaster, concrete compounds, fire stop mortar, and component of interior fill for wallboards or hollow bricks because of its good thermal properties, thermal and chemical reliability and thermal conductivity.     

Enhancement of latent heat energy storage using embedded heat pipes

Latent heat thermal energy storage (LHTES) utilizing heat pipes or fins is investigated experimentally. Photographic observations, melting and solidification rates, and PCM energy storage quantities are reported. Heat pipe effectiveness is defined and used to quantify the relative performance of heat pipe-assisted and fin-assisted configurations to situations involving neither heat pipes nor fins. For the experimental conditions of this study, inclusion of heat pipes increases PCM melting rates by approximately 60%, while the fins are not as effective. During solidification, the heat pipe-assisted configuration transfers approximately twice the energy between a heat transfer fluid and the PCM, relative to both the fin-assisted LHTES and the non-heat pipe, non-fin configurations.     

A numerical investigation into the charge behaviour of a spherical phase change material particle for high temperature thermal energy storage in packed beds

基于高温相变材料,对填充床储热系统中储热单元球体的储热性能进行了模拟研究.研究了不同传热流体温度和球体直径对球体储热性能的影响规律,对导热为主的相变储热过程与导热和自然对流共同作用的相变储热过程进行了比较分析,同时还探讨了高温辐射换热的影响.结果表明,相变时间随球体直径的增大而增大,随传热流体温度的增大而减小.当考虑相变区域自然对流时,总的相变时间显著减少,和单纯导热相比,完全相变时间缩短了近16%.在导热和自然对流的基础上加上辐射传热后可以看出,辐射换热强化了球体内的传热过程,加快了相变材料的熔化速度,强化了自然对流的作用.     

三套管式相变蓄热器强化传热研究

基于三套管式相变蓄热器的特点,提出应用T字形翅片来强化相变蓄热器的传热性能。研究结果表明:添加翅片可有效地降低蓄热器中相变材料的凝固和融化时间,直翅片和T字形翅片的混合强化结构能使凝固过程比未强化结构节省74%的时间,使融化过程节省60%的时间。因此直翅片和T字形翅片的混合使用可以达到进一步强化传热的目的。