掺杂元素La、F对尖晶石LiMn2O4材料结构及性能的影响

采用X-射线衍射仪(XRK)、扫描电子显微镜(SEM)、电池测试系统等研究了掺杂元素La、F对高温固相合成尖晶石型LiMn2O4材料的相结构、貌、活化性能、循环稳定性能的影响.结果表明:掺杂元素La、F可有效地提高LiMn2O4样品的充放电效率、循环稳定性能:随着掺杂元素F含量的增加,LiMn2O4-xFx样品的初始容量降低、循环稳定性能呈现出先增后减的变化规律;当掺杂元素La、F的含量较少时,LiLay,Mn2-yO4-xFx样品具有纯的尖晶石LMn2O4结构,样品呈球形或近球形,粒径范围为0.5～2.5 μm,LiLa0.02Mn1.98O3.95F0.05样品的初始放电容量为123.6mAh/g,经30次循环充放电后的容量为114.6mAh/g,容量保持率为92.7%,具有较好的活化性能和循环稳定性能.     

LiMg_(0.03)(Ni_(0.77)Co_(0.1)Mn_(0.1))O_2·B_2O_3球形高镍材料的制备与性能

采用液相共沉淀法制备球形掺镁高镍三元材料前驱体,结合高温固相法制备了氧化硼包覆高镍三元材料LiMg0.03(Ni0.77Co0.1 Mn0.1)O2·B2O3,对样品物理性能、电化学性能及安全稳定性进行分析测定,并对性能改善的机理进行分析。结果表明:通过Mg元素体相掺杂和B2O3表面包覆制备的球形高镍三元材料LiMg0.03(Ni0.77Co0.1Mn0.1)O2·B2O3具有良好的电化学性能和物理性能,对锂负极初始放电容量达到181 m A·h/g,对碳负极300次循环后,放电容量保持率达到92%,压实密度达到3.9 g/cm3。同时,LiMg0.03(Ni0.77Co0.1 Mn0.1)O2·B2O3具有良好的热稳定性和抗过充电的能力,在充电态下热分解温度比未掺杂和未包覆的样品提升12℃。     

稀土元素对LiMn_2O_4电极材料相结构及性能的影响

采用X射线衍射仪、扫描电子显微镜、电池测试系统等研究了不同稀土掺杂元素La、Ce、Nd等对Pechini法合成的LiMn2O4材料的相结构、形貌及电化学性能的影响规律.结果表明,合成的LiMn2O4、LiLa0.03Mn1.97O4、LiLa0.01Ce0.01Nd0.01Mn1.97O4样品具有纯尖晶石型LiMn2O4结构,LiLa0.015Ce0.015Mn1.97O4样品由LiMn:O.相及微量杂质相CeO2组成;样品呈规则的近球形或球形,其粒径范围为0.5～2.5μm.稀土元素取代使LiMn2O4材料的初始容量略有降低、循环稳定性能有较大增加,LiMn2O4、LiLa0.03Mn1.97O4、LiLa0.015Ce0.015Mn1.97O4、LiLa0.01Ce0.01Nd0.01Mn1.97O42样品的初始容量分别为126.0、120.0、117.3、124.0 mA·h/g,经30次循环充放电后的容量分别为88.9、102.7、101.6、109.1 mA·h/g.     

超级电容器用LiMn2O4的制备与性能

采用高温固相法制备尖晶石型LiMn2O4电极材料.XRD结果表明经700℃煅烧即可得到尖晶石型LiMn2O4样品.利用恒流充放电、循环伏安和交流阻抗等测试方法研究了合成过程中温度和时间对尖晶石型LiMn2O4电极材料在2mol·L-1.(NH4)2SO4溶液中电容性能的影响.结果表明LiMn2O4电极材料具有较好的电容性能.恒流充放电和循环伏安结果表明,当煅烧温度700℃,恒温时间4-2Ah时,其容量并没有明显的变化,电流密度为10mA·cm-2时,其放电比容量保持在127F·g-1.交流阻抗结果也表明,LiMn2O4电极在2mol·L"(-1H4)2SO4溶液中具有较好的电化学电容行为,700℃下煅烧的样品的溶液欧姆电阻仅为05Ω.     

多元稀土掺杂锂锰氧正极材料的结构及性能表征

采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、电池性能测试系统研究了多元稀土掺杂锂锰氧正极材料的相结构、形貌,并对其活化性能、循环稳定性能进行了表征。结果表明:采用Pechini法合成多元稀土掺杂LiMn2O4样品时,只有将掺杂元素的含量严格控制在一定范围内,所合成的LiMn2O4、LiLa0.03Mn1.97O4、LiLa0.012Ce0.012Mn1.976O4、LiLa0.012Nd0.012Mn1.976O4、LiCe0.012Nd0.012Mn1.976O4样品才具有纯尖晶石型LiMn2O4结构。当稀土掺杂元素含量较高时,所合成的LiLa0.015Ce0.015Mn1.97O4、LiLa0.015Nd0.015Mn1.97O4、LiCe0.015Nd0.015Mn1.97O4样品由LiMn2O4相及微量杂质相CeO2、Nd2O3、CeO2+Nd2O3组成。所有样品呈规则的近球形或球形,其粒径范围为0.5～2.8μm。适量的稀土元素掺杂将使LiMn2O4材料的初始容量减小、充放电效率及循环稳定性能增加,LiCe0.012Nd0.012Mn1.976O4样品具有较好的综合电化学性能,其初始容量为123.5mAh/g,经30次循环充放电后的容量为113.2mAh/g,为相同条件下LiMn2O4样品放电容量的1.27倍。     

以Mn3O4为前驱体制备尖晶石型LiMn2O4及其性能

采用改进的固相反应法合成了高性能的锂离子电池正极材料LiMn2O4。首先,以廉价的MnSO4为原料,通过水解氧化法制备纳米级Mn3O4前驱体;然后,将Mn3O4和Li2CO3混合均匀,在750℃固相反应20 h,得到尖晶石型LiMn2O4。用X射线衍射(XRD)和扫描电镜(SEM)对Mn3O4前驱体和LiMn2O4样品进行表征,用充放电测试和循环伏安技术对LiMn2O4样品进行电化学性能研究。结果表明:所制备的LiMn2O4具有完整的尖晶石型结构,且晶体粒子分布均匀。所制备的LiMn2O4材料在3.0~4.4 V之间,室温(25℃)下,在0.2C倍率下首次放电比容量为130.6 mA.h/g;在0.5C倍率下首次放电比容量为127.1 mA.h/g,30次循环后,容量仍有109.5 mA.h/g,且样品具有较好的高温性能。     

Al离子掺杂正极材料LiMn2O4的高温循环性能

采用固相反应法分别合成正极材料LiMn2O4和LiAlxMn2-xO4(x=0.05,0.1,0.3).对它们进行XRD和SEM测试,并对比了高温下的循环性能.结果显示:除Al掺杂量x=0.3时,合成物出现了LiAlO2杂质相外,其余皆具有单一的尖晶石相结构.掺杂后的晶体颗粒比较圆润.LiMn2O4在高温下经过20次循环后,其比容量降低29%,衰减很快.造成衰减的主要原因是Mn3+歧化反应生成的Mn2+在电解液中的溶解,以及Jahn-Teller效应.通过阳离子Al3+的掺杂,有效的提高了尖晶石LiMn2O4的高温循环性能.     

尖晶石LiMn_2O_4材料的高温固相合成及性能表征

本文采用热重分析仪(TGA)、X-射线衍射仪(XRD)、扫描电子显微镜(SEM)、电池测试系统等方法研究了尖晶石LiMn2O4材料的高温固相合成过程的相转变、形貌变化、晶格常数及电化学性能等变化规律.结果表明:合成温度较低时(≤823 K),样品由尖晶石型LiMn2O4相、微量MnO2相(673 K)或Mn2O3相(823 K)组成;当合成温度高于973 K时,样品由热稳定性能较好的纯尖晶石型LiMn2O4相组成.呈规则的球形或近球形,粒径范围为0.5～5μm.随着合成温度的升高,LiMn2O4样品的点阵常数、晶胞体积、颗粒尺寸等有不同程度的增加,放电容量呈先增后减的规律.     

Electrochemical performances and structure characteristic of LiMn2O4-xYx（Y=F, Cl, Br） compounds

Spinel LiMn2 O4-x Yx (Y=F, Cl, Br) compounds were prepared by solid-state reaction and the electrochemically galvanostatic charge-discharge cycles were performed using as-prepared compounds as cathode material. The influence of halogens on their lattice constants and the relation of electrochemical properties and their lattice constants were investigated. It is concluded that when the lattice constants are smaller than that of LiMn2O4, the reversible capacity fade is suppressed and the initial capacity sacrifice is observed. When the content of fluorine is 0.05, the lattice constant of LiMn2O3.95 F0.05 is larger than that of LiMn2O4, the initial capacity is improved. An efficient method was found to control the lattice constants of LiMn2O4 through the addition of halogen, and to improve the electrochemical performance of LiMn2O4. The LiMn2O3.95 F0.05 shows excellent electrochemical charge-discharge performance, with high initial capacity of 143 mAh/g and nearly no capacity loss after 116 cycles.     

Li1.05Ni0.05Mn1.9O4正极材料脱锂过程中的结构变化

与未掺杂的尖晶石LiMn2O4进行比较,用固相混合合成法制得的结晶良好的尖晶石Li1.05Ni0.05Mn19O4正极材料在室温和55℃下的循环性能都能得到较大改善,首次放电容量在室温和55℃分别保持理论容量的92.6%和91.5%.在常温条件下,以0.5 C充放电倍率循环50次,容量保持为首次放电容量的95.3%.采用非原位X射线衍射的方法对不同脱锂状态的Lix[Li005Ni005Mn19]O4(0.1＜x＜1)试样进行了结构分析.结果表明:Li、Ni的协同掺杂明显减小了晶格参数的变化,稳定了试样的结构及改善了电池循环性能.     

LiMgxNi0.5-xMn1.5O4的制备和电化学性能

为改善LiNi0.5Mn1.5O4的电化学性能,采用流变相法合成掺镁的锂离子电池正极材料LiMgxNi0.5-xMn1.5O4(x=0,0.05,0.1)。XRD测试结果表明所得材料仍为尖晶石结构。电化学性能测试结果显示:当x取值0.1,在3.5～4.9V电压范围内进行充放电循环时,材料LiMg0.1Ni0.4Mn1.5O4具有较好的循环性能,1C充放电时,初始放电比容量可达110.22mAh/g,30次循环后容量衰减率仅为7.7%。     

Synthesis and physicochemical properties of LiLa0.01Mnt.99O3.99F0.01 cathode materials for lithium ion batteries

Spinel lithium manganese oxide cathode materials were synthesized using the ultrasonic-assisted sol-gel method.The synthesized samples were investigated by differential thermal analysis (DTA) and thermogravimetry (TG),powder X-ray diffraction (XRD),scanning electron microscopy (SEM),cyclic voltammetry (CV),and the charge-discharge test.TG-DTA shows that significant mass loss occurs in two temperature regions during the synthesis of LiLa0.01Mn1.99O3.99F0.01.XRD data indicate that all samples exhibit the same pure spinel phase,and LiLa0.01Mn1.99O3.99F0.01 and LiLa0.01Mn1.99O4 samples have a better crystallinity than LiMn2O4. SEM images indicate that LiLa0.01Mn1.99O3.99F0.01 has a slightly smaller particle size and a more regular morphology structure with narrow size distribution.The charge-discharge test reveals that the initial capacities of LiMn2O4,LiLa0.01Mn1.99O4,and LiLa0.01Mn1.99O3.99F0.01 are 130,123,and 126 mAh·g-1,respectively,and the capacity retention rates of the initial value,after 50 cycles,are 84.8%,92.3%,and 92.1%,respectively.The electrode coulomb efficiency and CV reveal that the electrode synthesized by the ultrasonic-assistexi sol-gel (UASG) method has a better reversibility than the electrode synthesized by the sol-gel method.     

合成温度对LiMn1.95Mg0．05O4结构与性能的影响

用柠檬酸辅助溶胶一凝胶法在不同温度下合成了LiMn1.95Mg0．05O4正极材料。用X射线衍射、充放电测试以及电化学阻抗谱分析技术研究了不同合成温度对LiMn1.95Mg0．05O4结构和电化学性能的影响。结果表明：合成温度对LiMn1.95Mg0．05O4正极材料的晶相结构、电化学性能有显著影响,LiMn1.95Mg0．05O4尖晶石相的生成和长大与其合成的温度有密切的关系,合成的最佳温度为750℃;在750℃条件下合成的LiMn1.95Mg0．05O4具有较高的电化学活性和较好的晶相结构;高温合成有利于提高LiMn1.95Mg0．05O4正极材料的放电容量,低温合成有利于提高其循环性能。     

Powder electrochemical properties with different particle sizes of spinel LiAl0.05Mn1.95O4 synthesized by sol-gel method

An Al-doped spinel lithium manganese oxide was prepared by the adipic acid-assisted sol-gel method at 800℃, and the cathode materials （Liml0.05Mnl.9504） with different particle sizes were obtained through ball milling. The effects of particle size on the electrochemical performance of LiAl0.05Mnl.9504 samples were investigated by differential thermal analysis and thermogravimetry, X-ray diffraction, galvanostatic charge-discharge test, cyclic voltammetry, and electrochemical impedance spectroscopy. The results indicate that all samples with different particle sizes show the same pure spinel phase and good crystal structure; LiAlo.osMnl.9504 with Dso = 17.3 μm shows better capacity retention; LiAlo.osMnl.gsO4 cathode materials with small particle size have a bigger resistance of charge transfer than the large one, and the particle size has significant effects on the electrochemical performance of Al-doped spinel LiMn2O4 cathode materials.     

Synthesis and characterization of multidoped lithium manganese oxide spinel LiCo0.02La0.01Mn1.97O3.98Cl0.02

1 Introduction The cathode material plays an important role in the performance of lithium ion batteries. Lithium transition metal compounds with layered and spinel structure are favourites among cathode materials for lithium rechargeable batteries. In thi…     

Surface modification of LiCo0. 05Mn1.95O4 cathode by coating with SiO2-TiO2 composite

1　INTRODUCTIONSincethefirstcommercializationbySonyCorpo rationintheearly 1990s ,thelithium ionbattery(LIB)hasbecomeamajorproducttodominatethemarketforsmallrechargeablebatteries .Further more ,Li ionbatteriesareexpectedtobeusedasalarge scaleenergystoragedeviceforelectricvehices(EV ) [1] .ThoughvarioustypesofcathodematerialssuchasLiCoO2 ,LiNiO2 ,LiMn2 O4 ,andsubstitutedtran sitionmetaloxidesarecurrentlyusedincommercial izedLi ionbatteries[2 ,3] ,LiCoO2 inthesecathodematerialsismost…     

耐久型高倍率性能锰酸锂微球的合成(英文)

以Mn2+和NH4HCO3为原料,通过控制结晶法合成球形MnCO3前驱体模板。以LiNO3和MnCO3为原料,按照一定的摩尔比机械混合,在700°C下煅烧8h,合成高倍率性能和长循环性能的球形尖晶石LiMn2O4材料。分别考查原料的摩尔比、反应时间以及反应温度对前驱体MnCO3形貌和产率的影响。采用X射线粉末衍射和扫描电镜对合成的MnCO3和LiMn2O4进行表征,对LiMn2O4样品进行室温条件下的充放电性能测试。电化学测试结果表明:尖晶石锰酸锂微球在10C的放电倍率下的首次放电容量达90mA·h/g(1C放电容量为148mA/g),800次循环后容量保持率达到75%。该方法合成的LiMn2O4微球作为高功率型锂离子电池的正极材料有着较好的应用前景。