Engineering Efficiency Roll‐Off in Organic Light‐Emitting Devices

Previous studies have identified triplet‐triplet annihilation and triplet‐polaron quenching as the exciton density‐dependent mechanisms which give rise to the efficiency roll‐off observed in phosphorescent organic light‐emitting devices (OLEDs). In this work, these quenching processes are independently probed, and the impact of the exciton recombination zone width on the severity of quenching in various OLED architectures is examined directly. It is found that in devices employing a graded‐emissive layer (G‐EML) architecture the efficiency roll‐off is due to both triplet‐triplet annihilation and triplet‐polaron quenching, while in devices which employ a conventional double‐emissive layer (D‐EML) architecture, the roll‐off is dominated by triplet‐triplet annihilation. Overall, the efficiency roll‐off in G‐EML devices is found to be much less severe than in the D‐EML device. This result is well accounted for by the larger exciton recombination zone measured in G‐EML devices, which serves to reduce exciton density‐driven loss pathways at high excitation levels. Indeed, a predictive model of the device efficiency based on the quantitatively measured quenching parameters shows the role a large exciton recombination zone plays in mitigating the roll‐off.     

Low Roll‐Off and High Efficiency Orange Organic Light Emitting Diodes with Controlled Co‐Doping of Green and Red Phosphorescent Dopants in an Exciplex Forming Co‐Host

An exciplex forming co‐host is introduced in order to fabricate orange organic light‐emitting diodes (OLEDs) with high efficiency, low driving voltage and an extremely low efficiency roll‐off, by the co‐doping of green and red emitting phosphorescence dyes in the host. The orange OLEDs achieves a low turn‐on voltage of 2.4 V, which is equivalent to the triplet energy gap of the phosphorescent‐green emitting dopant, and a very high external quantum efficiency (EQE) of 25.0%. Moreover, the OLEDs show low efficiency roll‐off with an EQE of over 21% at 10 000 cdm^?2. The device displays a very good orange color (CIE of (0.501, 0.478) at 1000 cdm^?2) with very little color shift with increasing luminance. The transient electroluminescence of the OLEDs indicate that both energy transfer and direct charge trapping takes place in the devices.     

High Efficiency Deep‐Blue Phosphorescent Organic Light‐Emitting Diodes with CIE x,y (≤ 0.15) and Low Efficiency Roll‐Off by Employing a High Triplet Energy Bipolar Host Material

Recently, bipolar host materials are the most promising candidates for achieving high performance phosphorescent organic light‐emitting diodes (PHOLEDs) in order to maximize recombination efficiency. However, the development of host material with high triplet energy (E _T) is still a great challenge to date to overcome the limitations associated with the present PHOLEDs. Herein, a highly efficient donor‐π‐acceptor (D‐π‐A) type bipolar host (4′‐(9H‐carbazol‐9‐yl)‐2,2′‐dimethyl‐[1,1′‐biphenyl]‐4‐yl)diphenylphosphine oxide (m‐CBPPO) comprising of carbazole, 2,2′‐dimethylbiphenyl and diphenylphosphoryl as D‐π‐A unit, respectively, is developed. Interestingly, a high E _T of 3.02 eV is observed for m‐CBPPO due to highly twisted conformation. Furthermore, the new host material is incorporated in PHOLEDs as emissive layer with a new carbene type Ir(cb)₃ material as a deep‐blue emitter. The optimized devices show an excellent external quantum efficiency (EQE) of 24.8% with a notable Commission internationale de l'éclairage (x, y) ≤ 0.15, (0.136, 0.138) and high electroluminescence performance with extremely low efficiency roll‐off. Overall, the above EQE is the highest reported for deep‐blue PHOLEDs with very low efficiency roll‐off and also indicate the importance of appropriate host for the development of high performance deep‐blue PHOLEDs.     

Enhancement of External Quantum Efficiency of Red Phosphorescent Organic Light‐Emitting Devices with Facially Encumbered and Bulky PtII Porphyrin Complexes

An enhancement in the external quantum efficiency (QE) of red phosphorescent organic light‐emitting devices (OLEDs) by using facially encumbered and bulky meso‐aryl substituted Pt^II porphyrin complexes is demonstrated. The maximum external QEs of phosphorescent OLEDs doped with the facially non‐encumbered Pt^II porphyrin complex 1 [5,15‐bis[4‐(4,4‐dimethyl‐2,6‐dioxacyclohexyl)phenyl]‐2,8,12,18‐tetrahexyl‐3,7,13,17‐tetramethylporphyrin platinum(II )], the facially encumbered Pt^II porphyrin complex 2 [5,15‐bis(2,6‐dimethoxyphenyl)‐2,8,12,18‐tetrahexyl‐3,7,13,17‐tetramethylporphyrinato platinum(II )], the Pt^II porphyrin complex 3 that bears bulkier 3,5‐di‐tert‐butylphenyl substituents [5,15‐bis(3,5‐di‐t‐butylphenyl)‐2,8,12,18‐tetrahexyl‐3,7,13,17‐tetramethylporphyrin platinum(II )], and the “doubly‐decamethylene‐strapped” Pt^II porphyrin complex 4 were 1, 4.2, 7.3, and 8.2 %, respectively. The trend of increasing QE values in the order of 1 < 2 < 3 < 4 may be related to facial encumbrance and steric bulkiness of meso‐aryl substituted Pt^II porphyrin complexes. Especially, in the case of the Pt^II porphyrin 4 , it is considered that the “double straps” play an important role in restricting rotational freedom of the meso‐aryl substituents. The triplet excited‐state lifetimes for Pt^II porphyrins 1 – 4 in OLEDs at an injection current density of 0.55 mA cm^–2 were 80, 103, 140, and 152 μs, respectively. We believe that the trend of increasing triplet lifetime in going from 1 to 4 is correlated with suppressing non‐radiative decay.     

Bipolar Tetraarylsilanes as Universal Hosts for Blue,Green, Orange,and White Electrophosphorescence with High Efficiency and Low Efficiency Roll‐Off

A series of tetraarylsilane compounds, namely p‐BISiTPA ( 1 ), m‐BISiTPA ( 2 ), p‐OXDSiTPA ( 3 ), m‐OXDSiTPA ( 4 ), are designed and synthesized by incorporating electron‐donating arylamine and electron‐accepting benzimidazole or oxadiazole into one molecule via a silicon‐bridge linkage mode. Their thermal, photophysical and electrochemical properties can be finely tuned through the different groups and linking topologies. The para‐disposition compounds 1 and 3 display higher glass transition temperatures, slightly lower HOMO levels and triplet energies than their meta‐disposition isomers 2 and 4 , respectively. The silicon‐interrupted conjugation of the electron‐donating and electron‐accepting segments gives these materials the following advantages: i) relative high triplet energies in the range of 2.69–2.73 eV; ii) HOMO/LUMO levels of the compounds mainly depend on the electron‐donating and electron‐accepting groups, respectively; iii) bipolar transporting feature as indicated by hole‐only and electron‐only devices. These advantages make these materials ideal universal hosts for multicolor phosphorescent OLEDs. 1 and 3 have been demonstrated as universal hosts for blue, green, orange and white electrophosphorescence, exhibiting high efficiencies and low efficiency roll‐off. For example, the devices hosted by 1 achieve maximum external quantum efficiencies of 16.1% for blue, 22.7% for green, 20.5% for orange, and 19.1% for white electrophosphorescence. Furthermore, the external quantum efficiencies are still as high as 14.2% for blue, 22.4% for green, 18.9% for orange, and 17.4% for white electrophosphorescence at a high luminance of 1000 cd m^?2. The two‐color, all‐phosphor white device hosted by 3 acquires a maximum current efficiency of 51.4 cd A^?1, and a maximum power efficiency of 51.9 lm W^?1. These values are among the highest for single emitting layer white PhOLEDs reported till now.     

New Approach Toward Fast Response Light‐Emitting Electrochemical Cells Based on Neutral Iridium Complexes via Cation Transport

Here, a new method is presented to increase the turn‐on time and stability of light‐emitting electrochemical cells (LECs). To this end, a neutral iridium complex ( 5 ) containing a pendant Na⁺ ion that is generally known to have a faster mobility in the solid film than bulky anions is introduced, instead of the classic ionic transition metal complex (iTMC) with counter anion ( 7 ). Synthesis, photophysical and electrochemical studies of these complexes are reported. In the device configuration of ITO/ 5 or 7 +PEO (polyethylene oxide) (100–110 nm)/Au, as the voltage increases, complex 5 emits red light at ?3.6 V while complex 7 appears at –5.6 V, although their electrochemical and photophysical gap are similar. Furthermore, at constant voltage, –3 V, the turn‐on time of complex 5 was less than 0.5 min, which is a 60‐fold faster turn‐on time compared to the iTMC ( 7 ) with PF₆^?. These results are presumably due to the faster delivery of the Na⁺ ions to the electrode compared to PF₆^? ions. Also, the device lifetime of complex 5 exhibits a six‐fold increase in stability and a three‐fold shorter time to reach maximum brightness at constant bias compared to the device made with complex 7 .     

Facile Synthesis of Highly Efficient Lepidine‐Based Phosphorescent Iridium(III) Complexes for Yellow and White Organic Light‐Emitting Diodes

Highly efficient lepidine‐based phosphorescent iridium(III) complexes with pentane‐2,4‐dione or triazolpyridine as ancillary ligands have been designed and prepared by a newly developed facile synthetic route. Fluorine atoms and trifluoromethyl groups have been introduced into the different positions of ligand, and their influence on the photophysical properties of complexes has been investigated in detail. All the triazolpyridine‐based complexes display the blueshifted dual‐peak emission compared to the pentane‐2,4‐dione‐based ones with a broad single‐peak emission. The complexes show emission with broad full width at half maximum (FWHM) over 100 nm, and the emissions are ranges from greenish–yellow to orange region with the absolute quantum efficiency (Φ_PL) of 0.21–0.92 in solution, i.e., Φ_PL = 0.92 ( 18 ), which is the highest value among the reported neutral yellow iridium(III) complexes. Furthermore, high‐performance yellow and complementary‐color‐based white organic light‐emitting diodes (OLEDs) have been fabricated. The FWHMs of the yellow, greenish–yellow OLEDs are in the range of 94–102 nm, which are among the highest values of the reported yellow or greenish–yellow‐emitting devices without excimer emission. The maximum external quantum efficiency of monochrome OLEDs can reach 24.1%, which is also the highest value among the reported yellow or greenish–yellow devices. The color rendering indexes of blue and complementary yellow‐based white OLED is as high as 78.     

Thermally Activated Delayed Fluorescence Material as Host with Novel Spiro‐Based Skeleton for High Power Efficiency and Low Roll‐Off Blue and White Phosphorescent Devices

Efficiency roll‐off in blue organic light‐emitting diodes especially at high brightness still remains a vital issue for which the excitons density‐dependent mechanism of host materials takes most responsibility. Additionally, the efficiency roll‐off leads to high power consumption and reduces the operating lifetime because higher driving voltage and current are required. Here, by subtly modifying the triphenylamine to oxygen‐bridged quasi‐planar structure, a novel thermally activated delayed fluorescence type blue host Tri‐o‐2PO is successfully developed. Efficiency roll‐off based on Tri‐o‐2PO is ultralow with external quantum efficiency (EQE) just dropping by around 2% in the high luminance range from 1000 cd m^?2 to 10 000 cd m^?2. As expected, low turn‐on voltage (≈2.9 V) of device is also achieved, which is close to the theory limit value (≈2.62 V). Super‐high power efficiency (≈60 lm W^?1) and EQE (>22%) are also achieved when utilizing Tri‐o‐2PO as host. Furthermore, two‐color warm‐white light with CIE of (0.45, 0.43) and correlated color temperature of 2921 K is also fabricated and a champion EQE of 21% is delivered. These excellent performances prove the strategy of bridging the triphenylamine to reduce ΔE_st is validated and suggest the great potential of this novel skeleton.     

High‐Efficiency Near‐Infrared Fluorescent Organic Light‐Emitting Diodes with Small Efficiency Roll‐Off: A Combined Design from Emitters to Devices

The simultaneous realization of high quantum yield and exciton utilizing efficiency (η_r) is still a formidable challenge in near‐infrared (NIR) fluorescent organic light‐emitting diodes (FOLEDs). Here, to achieve a high quantum yield, a novel NIR dye, 4,9‐bis(4‐(diphenylamino)phenyl)‐naphtho[2,3‐c ][1,2,5]selenadiazole, is designed and synthesized with a large highest occupied molecular orbital/lowest unoccupied molecular orbital overlap and an aggregation‐induced emission property, which demonstrates a high photoluminescence quantum yield of 27% at 743 nm in toluene and 29% at 723 nm in a blend film. For a high η_r, an orange‐emitting thermally activated delayed fluorescent material, 1,2‐bis(9,9‐dimethyl‐9,10‐dihydroacridine)‐4,5‐dicyanobenzene, is chosen as the sensitizing host to harvest triplet excitons in devices. The optimized devices achieve a good η_r of 45.7% and a high external quantum efficiency up to 2.65% at 730 nm, with a very small efficiency roll‐off of 2.41% at 200 mA cm^?2, which are among the most efficient values for NIR‐FOLEDs over 700 nm. The effective utilization of triplet excitons via the thermally activated delayed fluorescence‐sensitizing host will pave a way to realize high‐efficiency NIR‐FOLEDs with small efficiency roll‐off.     

High Efficiency White Organic Light‐Emitting Devices Incorporating Yellow Phosphorescent Platinum(II) Complex and Composite Blue Host

A new class of charge neutral, strongly luminescent cyclometalated platinum(II) complexes supported by dianionic tetradentate ligand are synthesized. One of these platinum(II) complexes, Y‐Pt , displays a high photoluminescence quantum yield of 86% and electroluminescence efficacy (η_power) of up to 52 lm W^?1, and is utilized as a yellow phosphorescent dopant in the fabrication of white organic light‐emitting devices (WOLEDs). WOLEDs based on conventional structures with yellow emission from Y‐Pt in combination with blue emission from bis(4,6‐difluorophenyl‐pyridinato‐N,C²′) (picolinate) iridium(III) (FIrpic) show a total η_power of up to 31 lm W^?1. A two‐fold increase in η_power by utilizing a modified WOLED structure comprising of a composite blue host is realized. With this modified device structure, the total η_power and driving voltage at a luminance of 1000 cd m^?2 can be improved to 61 lm W^?1 and 7.5 V (i.e., 10 V for control devices). The performance improvement is attributed to an effectively broaden exciton formation‐recombination zone and alleviation of localized exciton accumulation within the FIrpic‐doped composite host for reduced triplet‐triplet annihilation, yielding blue light‐emission with enhanced intensity. The modified device structure can also adopt a higher concentration of Y‐Pt towards its optimal value, leading to WOLEDs with high efficiency.     

Novel Heteroleptic CuI Complexes with Tunable Emission Color for Efficient Phosphorescent Light‐Emitting Diodes

A series of orange‐red to red phosphorescent heteroleptic Cu^I complexes (the first ligand: 2,2′‐biquinoline (bq), 4,4′‐diphenyl‐2,2′‐biquinoline (dpbq) or 3,3′‐methylen‐4,4′‐diphenyl‐2,2′‐biquinoline (mdpbq); the second ligand: triphenylphosphine or bis[2‐(diphenylphosphino)phenyl]ether (DPEphos)) have been synthesized and fully characterized. With highly rigid bulky biquinoline‐type ligands, complexes [Cu(mdpbq)(PPh₃)₂](BF₄) and [Cu(mdpbq)(DPEphos)](BF₄) emit efficiently in 20 wt % PMMA films with photoluminescence quantum yield of 0.56 and 0.43 and emission maximum of 606 nm and 617 nm, respectively. By doping these complexes in poly(vinyl carbazole) (PVK) or N‐(4‐(carbazol‐9‐yl)phenyl)‐3,6‐bis(carbazol‐9‐yl) carbazole (TCCz), phosphorescent organic light‐emitting diodes (OLEDs) were fabricated with various device structures. The complex [Cu(mdpbq)(DPEphos)](BF₄) exhibits the best device performance. With the device structure of ITO/PEDOT/TCCz:[Cu(mdpbq)(DPEphos)](BF₄) (15 wt %)/TPBI/LiF/Al (III), a current efficiency up to 6.4 cd A^–1 with the Commission Internationale de L'Eclairage (CIE) coordinates of (0.61, 0.39) has been realized. To our best knowledge, this is the first report of efficient mononuclear Cu^I complexes with red emission.     

Crosslinkable TAPC‐Based Hole‐Transport Materials for Solution‐Processed Organic Light‐Emitting Diodes with Reduced Efficiency Roll‐Off

1‐Bis[4‐[N,N‐di(4‐tolyl)amino]phenyl]‐cyclohexane (TAPC) has been widely used in xerography and organic light‐emitting diodes (OLEDs), but derivatives are little known. Here, a new series of solution‐processable, crosslinkable hole conductors based on TAPC with varying highest occupied molecular orbital (HOMO) energies from ?5.23 eV to ?5.69 eV is implemented in blue phosphorescent OLEDs. Their superior perfomance compared with the well‐known N4,N4,N4′,N4′‐tetraphenylbiphenyl‐4,4′‐diamine (TPDs) analogues regarding hole‐injection and mobility, electron and exciton blocking capabilities, efficiency, and efficiency roll‐off is demonstrated. Overall, the TAPC‐based devices feature higher luminous and power efficiency over a broader range of brightness levels and reduced efficiency roll off. A systematic broadening of the emission zone is observed as the hole‐injection barrier between the anode and the hole‐transporting layer increased.     

Improved Efficiency of Single‐Layer Polymer Light‐Emitting Devices with Poly(vinylcarbazole) Doubly Doped with Phosphorescent and Fluorescent Dyes as the Emitting Layer

We demonstrate novel organic light‐emitting diode (LED) materials that contain a green phosphorescent dye (dmbpy)Re(CO)₃Cl (dmbpy = 4,4′‐dimethyl‐2,2′‐bipyridine), and a red fluorescent dye 4‐dicyanomethylene‐6‐(p‐dimethylaminostyryl)‐2‐methyl‐4H‐pyran (DCM) as dopants and polyvinylcarbazole (PVK) as the host. The photoluminescence (PL) and electroluminescence (EL) properties of these complex materials were studied. The energy transfer efficiency from PVK host to DCM is increased by the (dmbpy)Re(CO)₃Cl co‐dopant, which has an emission energy between that of PVK and DCM. The (dmbpy)Re(CO)₃Cl, which emits a long‐lived phosphorescence, is used as an energy coupler, providing the possibility to harvest both singlet and triplet energy in the devices. The pure red emission from DCM was observed from PL and EL spectra of (dmbpy)Re(CO)₃‐Cl(> 2.0 wt.‐%):DCM(> 0.5 wt. %) doped PVK films, demonstrating an efficient energy transfer from PVK and (dmbpy)Re(CO)₃‐Cl to DCM. By optimizing the concentration of DCM and (dmbpy)Re(CO)₃Cl in PVK, a maximum EL quantum efficiency of 0.42 cd A^–1 at a current density of 9.5 mA cm^–2 was obtained. The EL quantum efficiency of the doubly doped device is significantly enhanced in comparison with both a DCM‐only doped PVK device and a DCM‐doped PVK device with the green fluorescent dye Alq₃ as co‐dopant. The improvement in the operating characteristics of the phosphorescent and fluorescent dye doubly doped device is attributed to efficient energy transfer in the system, in which both triplet and singlet excitons are used for resultant emission in the polymer device.     

An Indolocarbazole‐Based Thermally Activated Delayed Fluorescence Host for Solution‐Processed Phosphorescent Tandem Organic Light‐Emitting Devices Exhibiting Extremely Small Efficiency Roll‐Off

The study reports the development of a solution‐processed phosphorescent tandem organic light‐emitting device (OLED) exhibiting extremely small efficiency roll‐off. The OLED comprises two light‐emitting units (LEUs) connected by an interconnecting unit and employs a thermally activated delayed fluorescence host material. One of the most difficult tasks in the fabrication of OLEDs is to form a multilayer structure without dissolving the underlayer during the coating of the upper layer. The developed host materials exhibit high tolerance to methanol. The upper‐layer adjacent to the light‐emitting layer consists of ZnO nanoparticles, which could be dispersed in methanol by improving the preparation method. This results in the successful fabrication of a solution‐processed phosphorescent tandem OLED comprising two LEUs. The maximum external quantum efficiency (EQE) of the tandem device is 22.8%, and the EQE is 21.9% even at a high luminance of 10 000 cd m^?2. The suppression of efficiency roll‐off is among the best of those previously reported. Moreover, the operational stability of the tandem device is much higher compared with single‐LEU devices.     

Doping‐Free Organic Light‐Emitting Diodes with Very High Power Efficiency,Simple Device Structure,and Superior Spectral Performance

Today's state‐of‐the‐art phosphorescent organic light‐emitting diodes (PhOLEDs) must rely on the host‐guest doping technique to decrease triplet quenching and increase device efficiency. However, doping is a sophisticated device fabrication process. Here, a Pt(II)‐based complex with a near unity photoluminescence quantum yield and excellent electron transporting properties in the form of neat film is reported. Simplified doping‐free white PhOLED and yellow‐orange PhOLED based on this emitter achieve rather low operating voltages (2.2–2.4 V) and very high power efficiencies of approximately 80 lm W^?1 (yellow‐orange) and 50 lm W^?1 (white), respectively, without any light extraction enhancement. Furthermore, the efficient white device also exhibits high color stability. No color shift is observed during the entire operation of the device. Analysis of the device's operational mechanism has been postulated in terms of exciton and polaron formation and fate. It is found that using the efficient neat Pt(II)‐complex as a homogeneous emitting and electron transporting layer and an ambipolar blue emitter are determining factors for achieving such a high efficiency.     

Correlation Between Triplet–Triplet Annihilation and Electroluminescence Efficiency in Doped Fluorescent Organic Light‐Emitting Devices

Triplet–triplet annihilation (TTA) is studied in a wide range of fluorescent host:guest emitter systems used in organic light‐emitting devices (OLEDs). Strong TTA is observed in host:guest systems in which the dopant has a limited charge‐trapping capability. On the other hand, systems in which the dopant can efficiently trap charges show insignificant TTA, an effect that is due, in part, to the efficient quenching of triplet excitons by the trapped charges. Fluorescent host:guest systems with the strongest TTA are found to give the highest OLED electroluminescence efficiency, a phenomenon attributed to the role of TTA in converting triplet excitons into additional singlet excitons, thus appreciably contributing to the light output of OLEDs. The results shed light on and give direct evidence for the phenomena behind the recently reported very high efficiencies attainable in fluorescent host:guest OLEDs with quantum efficiencies exceeding the classical 25% theoretical limit.     

Highly Efficient Three Primary Color Organic Single‐Crystal Light‐Emitting Devices with Balanced Carrier Injection and Transport

Organic single crystals have a great potential in the field of organic optoelectronics because of their advantages of high carrier mobility and high thermal stability. However, the application of the organic single crystals in light‐emitting devices (OLEDs) has been limited by single‐layered structure with unbalanced carrier injection and transport. Here, fabrication of a multilayered‐structure crystal‐based OLED constitutes a major step toward balanced carrier injection and transport by introducing an anodic buffer layer and electron transport layer into the device structure. Three primary color single‐crystal‐based OLEDs based on the multilayered structure and molecular doping exhibit a maximum luminance and current efficiency of 820 cd cm^?2 and 0.9 cd A^?1, respectively, which are the highest performance to date for organic single‐crystal‐based OLEDs. This work paves the way toward high‐performance organic optoelectronic devices based on the organic single crystals.