星载DBF Tx射频通道幅相误差校正

为了实现精确的多波束形成,该文提出了一种补偿卫星通信多波束系统发射通道幅相误差的校正方法,该方法在发射通道中同时注入多路正交码变换的校正测试信号,通过接收多路发射机的输出信号和,在基带校正算法单元利用正交码的时间相关性和IDFT并行处理的方法,同时得到多路射频通道的校正因子,并对得到的校正因子进行了归一化处理,消除了对通道中非线性器件的影响.仿真结果表明,该方法可以有效地补偿射频通道间的幅相不一致性,校正后的波束方向图接近理想的波束方向图.     

基于近场测试的相控阵天线自动化校准 与阵面监测方法

相控阵天线装配好之后,由于各组成部件机械加工误差、装配误差、部件老化更换和环境温度改变等因素,各 单元通道的初始幅相产生差异,因此必须对天线的所有系统进行校准。本文针对小型化相控阵平台,通过硬连接将相控 阵天线的波控系统与测试设备相结合,提出一种简便的自动化近场逐点校准方法。同时,本文还提出一种简单的外监测 方法。当相控阵天线工作期间,可对阵面的幅相分布进行监测。可在相控阵天线工作期间,对近场幅相校准数据进行修 正,达到阵面自身校准的目的。经对一个16阵元的相控阵天线进行实验测量可知,该自动化校准与阵面自身校准方法可 以准确、快捷测试出天线阵面的幅相分布。非常适合一维、二维相控阵天线,尤其是小型化相控阵天线的幅相校准与监 测。     

数字阵列天线接收通道宽带信号校准与波束形成技术研究

 本文提出了一种简洁、实用的天线接收通道宽带信号校准方法.该方法采用零中频信号处理技术,通过理论分析将数字阵列天线接收通道宽带线性调频信号校准分为通道间的时间和相位校准,证明了接收通道间宽带线性调频信号相位校准可以转化为单频信号进行,给出了接收通道间宽带信号的幅度校准方法和时间校准允许的误差范围.在通道校准基础上,采用脉冲压缩技术合成了宽带天线方向图.实验结果表明,本文方法是有效、可行的.     

一种低轨卫星接收的相控阵天线校准方法

针对相控阵天线设计中传统校准方法的缺陷,提出了一种适用于低轨卫星信号接收的通道校准方法,利用实际卫星下行信号对相控阵天线的各接收通路进行动态校准。该方法根据星历得到卫星动态位置坐标,计算卫星相对天线的方位和俯仰角度和理论相位差,再采集各个通路的实际信号,测量实际的相位差,理论值和实测值之间的差异即通道不一致性。最后利用波束合成指标验证了改进后校准的正确性。该方法简单可行,为低轨卫星侦察时相控阵天线的设计提供了一种先进、合理、有效的校准方案。     

多波束相控阵天线角度测量方法

在雷达、通信、测控等领域中,基于相控阵天线的幅度和差单脉冲测角技术是基本方法,但该方法通过旋转法向方向图去近似表示子波束方向图,并用一阶泰勒公式近似表示子波束接收信号幅度,从而带来非噪声因素误差,最终导致目标角度估计精度不高。为此,通过相控阵天线同时产生两个形状相同但相互独立的子波束,旋转波束指向中心轴方向的方向图函数来确定两个子波束的方向图函数,并用高阶泰勒公式对子波束接收信号幅度进行近似,从而减少误差。仿真和硬件测试结果表明所提方法能够有效提高测角精度。     

通道幅相误差对数字阵列天线性能影响及校准

为实现低副瓣数字阵列天线性能,需要对阵面通道幅相误差进行校准。针对此问题,定性分析了通道幅相误差、阵面通道数与数字阵列天线主要性能(副瓣电平、波束指向、增益)的相对关系,分析结果表明:通道间幅相误差越大,副瓣电平、波束指向、增益越差;通道数越多,副瓣电平、波束指向受通道误差影响越小,而增益受通道幅相误差的影响与阵面通道数无关。结合数字阵雷达实际使用中阵面通道幅相误差修调问题,重点研究了通道误差测量方法。给出了利用内监测法和中场测量法进行通道误差测量的原理、实现方法及适用条件,该2种通道误差测量方法可以作为互补手段使用。最后,给出了一种基于多次测量取平均值的数字阵列幅相误差校准方法,仿真结果表明:校准前后,通道幅相误差分别由2 d B和20°变为0.4 d B和2°,满足指标要求。     

子阵级DBF体制天线幅相误差校准方法

在子阵级DBF体制天线中,接收多路信号,这些信号通过射频通道会增加额外的增益,致使各通道的幅相特性产生差异,影响雷达的测角精度,所以必须将各路子阵幅相误差消除,保证各通道幅相一致.本文提出了一种工程中实用的误差校准方法,并通过仿真论证了该方法的可行性.     

有源相控阵天线的近场校准

为实现对相控阵天线的校准,降低幅相误差和阵元失效对天线性能的影响,提出了一种考虑互耦效应的近场校准方法。在利用近场扫描法完成逐一通道校准的基础上,使用旋转矢量法进行二次校准。在应用旋转矢量法（ REV)时,为使被测信号的变化明显,将大规模相控阵天线分为中间、边缘区域进行分区校准。通过二次校准可判定阵元是否失效,提高相控阵天线的幅相一致性;通过分区校准减小阵元间互耦的影响,缩短校准时间。仿真结果表明：此方法用于大型相控阵的校准具有较高的准确性,可改善校准结果。     

基于通道合成的数字阵列通道校准方法

通道校准是数字阵雷达的重要技术之一,校准精度影响波束指向、副瓣电平等多个波束形成指标,从而影响整个雷达性能。随着数字阵列规模的不断提升,通道校准对测试时间和测试精度的要求也随之提高。文中首先介绍了一种基于通道合成的数字阵列通道校准方法原理和组成,给出了该测试方法的校准算法;然后,与传统数字阵列通道校准方法的信噪比、记录量、测试时间、幅相标准差等校准性能进行比较;最后,给出了实际测量形成的天线方向图,验证了该方法的有效性。     

阵列天线近场校准方法及在波束形成中的应用

大型相控阵天线阵列由于天线口径很大,给天线远场测试带来很多困难,天线近场测试方法可以有效解决这类问题。本文在实际工程中利用天线近场测试方法对大型天线阵列的幅相误差进行了测试及校准。试验结果表明,此方法可以用于评估阵列天线的一致性。波束形成后,相对于接收机闭环校准,天线误差校准可以明显降低旁瓣,并且测角偏差明显减少,在短波低频段表现尤为突出。     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first     

JOURNAL OF ELECTRONICS(CHINA)

正~~     

NEXT GENERATION WIRELESS NETWORKS–ESPECIALLY THE USE OF MILLI-MICROWAVE BANDS

The global bandwidth shortage of wireless communications has motivated the exploration of the naillimeter wave （ram-wave） frequency spectrum for the next generation wireless communications. Recent advances in RF CMOS technology and high speed baseband signal processing technologies have enabled tile extensive research and development of turn-wave wireless communications. The multi gigabit per second data rate of ram-wave system will lead to applications in many important scenarios, such as WPAN, WLAN,back-haul for cellular system. And the frequency bands include 28 GHz, 38 GHz, 45GHz, 60GHz, E-BAND and even beyond 100 GHz. The propagation and the imitation of the RF circuits design in these frequency bands make the directional antennas be inevitable for mm-wave communications.