Cure kinetics of multifunctional epoxies with 2,2′‐dichloro‐4,4′‐diaminodiphenylmethane as hardener

The curing behavior of the epoxy resin N,N,N′,N′‐tetraglycidyldiaminodiphenyl methane (TGDDM) with triglycidyl p‐aminophenol as a reactive diluent was investigated using 2,2′‐dichloro‐4,4′‐diaminodiphenylmethane (DCDDM) as the curing agent. The effect of the curing agent on the kinetics of curing, shelf‐life, and thermal stability in comparison with a TGDDM‐diaminodiphenylsulfone (DDS) system was studied. The results showed a lesser activation energy at the lower level of conversion with a broader cure exotherm for the epoxy‐DCDDM system in comparison with the epoxy‐DDS system, although the overall activation energy for the two systems was comparable. TGA studies showed more stability in the epoxy‐DCDDM system than in the epoxy‐DDS system. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2097–2103, 2000     

Radiopaque acrylic bone cements with bromine‐containing monomer

One important issue for the acrylic bone cements concerns the radiopacity, which may be achieved by different ways. In this work, a new bromine‐containing acrylic monomer, the 2‐(2‐bromopropionyloxy) propyl methacrylate (BPPM), was synthesized and proposed to be used for providing radiopaque bone cements. Different acrylic bone cements were realized by partially replacing the methyl methacrylate (MMA) monomer phase with 5–20% w/w of BPPM‐comonomer. The effect of this comonomer on the curing parameters of acrylic bone cements, on their thermal and rheological properties, water absorption, density, contact angle, compression tests, and radiopacity was studied. It appears that the presence of BPPM does provide radiopacity, improves the curing parameters by decreasing the maximum curing temperature and increasing the setting time. The new BPPM‐acrylic bone cements exhibit lower glass transition temperature and better thermal stability when compared with the classical radiolucent acrylic cements. Rheological measurements have shown that 10–20% w/w of BPPM in the liquid phase of acrylic bone cement formulations increase its flexibility, and may also induce a slight crosslinking reaction during the curing phase. BPPM‐modified acrylic bone cements present lower polymerization shrinkage and higher compression strength, and similar water uptake, porosity, and water contact angle as the radiolucent PMMA‐cements. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

One‐pot curing system of epoxy resin imines initiated with water

The curing and adhesive properties of one‐component epoxy resins containing Epikote 828 and diimines, derived from N,N′‐di(1‐ethylpropylidene)‐m‐xylylenediamine, N,N′‐di(1‐ethylpropylidene)‐1,3‐diaminomethylcyclohexane (2), and N,N′‐di(1,3‐dimethylbutylidene)‐m‐xylylenediamine, which were used as water‐initiated hardeners, were examined. Diethyl ketone‐based imines with a lower electron density on the C?N carbon were efficiently hydrolyzed and showed curing activity. 2, a novel diethyl ketone‐based diimine, served as an efficient latent hardener of the epoxy resin. A paste of the epoxy resin with 2 showed good storage stability at room temperature and good adhesive properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 878–882, 2003     

Time–temperature–transformation cure diagrams of phenol–formaldehyde and lignin–phenol–formaldehyde novolac resins

In this study, the time–temperature– transformation (TTT) cure diagrams of the curing processes of several novolac resins were determined. Each diagram corresponded to a mixture of commercial phenol–formaldehyde novolac, lignin–phenol–formaldehyde novolac, and methylolated lignin–phenol–formaldehyde novolac resins with hexamethylenetetramine as a curing agent. Thermomechanical analysis and differential scanning calorimetry techniques were applied to study the resin gelation and the kinetics of the curing process to obtain the isoconversional curves. The temperature at which the material gelled and vitrified [the glass‐transition temperature at the gel point (_gelT_g)], the glass‐transition temperature of the uncured material (without crosslinking; T_g0), and the glass‐transition temperature with full crosslinking were also obtained. On the basis of the measured of conversion degree at gelation, the approximate glass‐transition temperature/conversion relationship, and the thermokinetic results of the curing process of the resins, TTT cure diagrams of the novolac samples were constructed. The TTT diagrams showed that the lignin–novolac and methylolated lignin–novolac resins presented lower T_g0 and _gelT_g values than the commercial resin. The TTT diagram is a suitable tool for understanding novolac resin behavior during the isothermal curing process. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Phosphorus‐containing epoxy resins: Thermal characterization

Three novel aromatic phosphorylated diamines, i.e., bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl} pyromellitamic acid (AP), 4,4′‐oxo bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl}phthalamic acid (AB) and 4,4′‐hexafluoroisopropylidene‐bis N,N′‐{3‐[(3‐aminophenyl)methyl phosphinoyl] phenyl}phthalamic acid (AF) were synthesized and characterized. These amines were prepared by solution condensation reaction of bis(3‐aminophenyl)methyl phosphine oxide (BAP) with 1,2,4,5‐benzenetetracarboxylic acid anhydride (P)/3,3′,4,4′‐benzophenonetetracarboxylic acid dianhydride (B)/4,4′‐(hexafluoroisopropylidene)diphthalic acid anhydride (F), respectively. The structural characterization of amines was done by elemental analysis, DSC, TGA, ¹H‐NMR, ¹³C‐NMR and FTIR. Amine equivalent weight was determined by the acetylation method. Curing of DGEBA in the presence of phosphorylated amines was studied by DSC and curing exotherm was in the temperature range of 195–267°C, whereas with conventional amine 4,4′‐diamino diphenyl sulphone (D) a broad exotherm in temperature range of 180–310°C was observed. Curing of DGEBA with a mixture of phosphorylated amines and D, resulted in a decrease in characteristic curing temperatures. The effect of phosphorus content on the char residue and thermal stability of epoxy resin cured isothermally in the presence of these amines was evaluated in nitrogen atmosphere. Char residue increased significantly with an increase in the phosphorus content of epoxy network. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2235–2242, 2002     

Effect of isomerization on thermal behaviour of bisitaconimides

The effect of isomerization of N,N′‐bisitaconimido‐4,4′‐diphenyl ether to the corresponding biscitraconimide on the curing characteristics and thermal stability of cured resins is described. Resins having bisitaconimide:biscitraconimide ratios of 23:77–93:7 were prepared by reacting 4,4′‐diaminodiphenyl ether with itaconic anhydride in solvents of different polarities and under different reaction conditions. Resins containing a higher proportion of citraconimide had a lower melting point (191 vs 208 °C). The curing exotherm was observed immediately after melting in all the resins and exothermic peak temperature reduced with increase in citraconimide content. Resins having a higher proportion of citraconimide on isothermal curing (200 °C, 2 h) and subsequent heating in nitrogen atmosphere degraded at a slightly lower temperature. However, the char yield at 800 °C did not show any systematic dependence on citraconimide content. © 2002 Society of Chemical Industry     

N-methylaniline formaldehyde: Its synthesis and use as an epoxy curing agent

A series of poly-secondary aromatic amines was prepared by the acid-catalyzed condensation of N-methylaniline with formaldehyde. These condensation products were evaluated as curing agents for a standard epoxy prepolymer, namely bis(2,3-epoxypropoxyphenyl)propane. Various molar ratios of N-methylaniline to formaldehyde were used to produce polyamine condensation products with varying degrees of polymerization. These molar ratios ranged from 1.60 to 1.30. Dielectric properties of the cured epoxy resins at temperatures above 100°C. were highly dependent upon these ratios. Lower-ratio condensation products produced resins with optimum dielectric properties at the higher temperature and also with good physical properties.     

Synthesis and characterization of thermosetting polyacetylene-terminated silicone resins

A novel polyacetylene-terminated silicone (PTS) resins possessing low curing temperature and high heat resistance has been prepared by Grignard reaction using m-diacetylenylbenzene (DEB), 1,3,5-triacetylenylbenzene(TEB), and dichlorosilane as original materials. The reaction of the functional groups was characterized by in situ Fourier transform infrared spectrometer. The experimental results indicated that Si─H and C≡CH bonds are almost exclusively involved in the crosslinking reaction, while ─C≡C─ bonds only partially react. Further, Si─H and C≡CH bonds can participate in the curing reaction at relatively low temperatures, but ─C≡C─ bonds require higher temperature, indicating the higher activity of Si─H and C≡CH bonds than ─C≡C─ bonds. As determined by differential scanning calorimetry, PTS resins have low peak exothermic temperature at 184.5 °C, which is lower than MSP resin (~ 210 °C); in addition, rheological test showed that PTS resins have a very wide processing window from 40 to 163.3 °C, indicating that the PTS resins have excellent processability with a low curing temperature and wide processing window. What is more, TGA results of thermal-cured PTS resins revealed that T_d5 (5% weight loss temperature) of PTS-H10 reached the highest of 684.4 °C. Compared with PTS-H0 resin, there is an increase of 124.2 °C and the remarkably increased heat resistance correlated with a higher m-DEB input ratio. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48783.     

Antibacterial materials: structure–bioactivity relationship of epoxy–amine resins containing quaternary ammonium compounds covalently attached

Bifunctional aminoalkyldimethylpropylammonium salts (N‐(3‐aminopropyl)‐N,N‐dimethylpentylammonium chloride, N‐(3‐aminopropyl)‐N,N‐dimethyloctylammonium chloride, N‐(3‐aminopropyl)‐N,N‐dimethyldecylammonium chloride, N‐(3‐aminopropyl)‐N,N‐dimethyldodecylammonium chloride) are synthesized and their structure‐dependent antibacterial effect against Gram‐negative Escherichia coli and Gram‐positive Lactococcus lactis is investigated. To this end, resins prepared from bisphenol A diglycidyl ether (2,2‐bis[4‐(glycidyloxy)phenyl]propane) and diethylenetriamine (2,2′‐diaminodiethylamine) as matrix and the bifunctional aminoalkyldimethylpropylammonium salts in a ratio of 6 mol% compared to epoxy components are used. A dependence of antibacterial effect on alkyl chain length of the quaternary ammonium compounds is observed for both species. Furthermore, resins with N‐(3‐aminopropyl)‐N,N‐dimethyldecylammonium chloride in varying concentrations up to 16 mol% for both organisms show a concentration‐dependent antibacterial effect of the quaternary ammonium salt. The antibacterial materials are characterized by differential scanning calorimetry, infrared spectroscopy and rheological studies. © 2013 Society of Chemical Industry     

High-performance poly(methylsilane arylether arylacetylene) resins with low curing temperatures and weak secondary relaxations

A series of poly(methylsilane arylether arylacetylene) (PSEA-H) resins were synthesized from methyldichlorosilane and isomeric arylether arylacetylenes, and characterized by ¹H-NMR and FT-IR spectroscopies. The effect of reactive Si-H groups and the linking positions of benzene rings in the arylether arylacetylene units on the properties of the resins were investigated. The results show that PSEA-H resins possess good processability with processing windows of over 80°C. The introduction of Si-H groups reduces the curing temperatures for PSEA-H resins and weakens the secondary relaxation for the cured PSEA-H resins. The cured resins and T300 carbon fiber (T300CF) reinforced composites display high mechanical properties. The flexural strengths of a cured PSEA-H resin and its T300CF composite at room temperature reach 64.2 and 426.5 MPa, respectively. The flexural properties depend on the linking positions of benzene rings. The cured PSEA-H resins show excellent heat resistance with a temperature of 5% weight loss (T_d5) above 500°C.     

Dynamic mechanical analysis study of the curing of phenol‐formaldehyde novolac resins

The curing reaction of typical commercial phenol‐formaldehyde novolac resins with hexamethylentetraamine (HMTA) was followed by dynamic mechanical analysis. The evolution of the rheological parameters, such as storage modulus G′, loss modulus G″, and tanδ (G″/G′), as a function of time, for samples of the phenolic resins on cloth, was recorded. The curing reaction, leading to the formation of a crosslinked structure, is described by a third‐order phenomenological equation. This equation takes into account a self‐acceleration effect, as a consequence not only of the chemical reaction of crosslinking after the gel point but of phase segregation as well. This rheokinetic model of the curing of phenolic novolac resins permits the determination of the numerical values of the kinetic equation constants. The influence of the composition, structure, and physical treatment on the curing kinetics of the novolac resins is evaluated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1902–1913, 2001     

Acrylic bone cements: Effects of the poly(methyl methacrylate) powder size and chitosan addition on their properties

The effect of the particle size of poly(methyl methacrylate) (PMMA) and the incorporation of chitosan (CH) on the mechanical and thermal properties and the biocompatibility of acrylic bone cements were investigated. Three groups of bone cements were prepared with different PMMA particles. Groups 1 (BC1) and 2 (BC2) contained ground and sieved PMMA with particle sizes in the ranges 50–150 μm and 1–50 μm, and group 3 (BC3) contained synthesized PMMA microspheres with a size of about 1 μm. The mechanical properties of the three groups were similar, but their curing properties were significantly affected. The presence of CH improved the mechanical and thermal properties. For the BC1 group, the compressive strength increased more than 10 MPa, and the curing temperature decreased 12°. The cement having the optimum properties (BC1) was applied to rats, where it enhanced the bone bonding ability, and bioactivity was observed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39662.     

Silicon-containing fluorenylacetylene resins with low curing temperature and high thermal stability

Silicon-containing arylacetylene resins (PSAs) are promising thermal stability polymers for many applications. However, the controllability of curing reaction limited their application because of the high curing temperature and enthalpy. In this study, Materials Genome Initiative was utilized to screen out a target monomer, 2,7-diethynyl-9H-fluorene (DEF), for design of new PSAs with low curing temperature and enthalpy. After incorporation of DEF, the obtained silicon-containing fluorenylacetylene resins (PSA-VBF) could be cured at a lower temperature of 149.2 °C with lower enthalpy (239.8 J g⁻¹) than the reported PSA-V (190.0 °C, 368.3 J g⁻¹). Moreover, the thermal curing behavior and mechanism were investigated by differential scanning calorimetry, Fourier transform infrared, and pyrolysis-gas chromatography–mass spectrometry. The results revealed that with the increased of DEF, the curing reaction of PSA-VBF became dominated by Diels–Alder reaction. And the formed aromatic fused rings endowed the cured PSA-VBF with excellent thermal stability, which were proved by thermogravimetric analysis results that the temperature at 5% weight loss (T_d5) of the cured copolymers ranged from 630 to 639 °C, and the char yield at 1000 °C was above 90%. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48262.     

Amine Modifiers with an s‐Triazine Ring for Unsaturated Polyester Resins, 1

Summary: Synthesis and properties of amine modifiers for unsaturated polyester resins are presented. The modifiers were obtained by reacting 3‐azapentan‐1,5‐diol (diethanoloamine) with 2,4‐dichloro‐6‐methoxy‐1,3,5‐triazine, 2‐chloro‐4,6‐dimethoxy‐1,3,5‐triazine or with cyanuric chloride. They were incorporated into the structure of typical unsaturated polyester resins in the polycondensation stage, i.e. prior to dilution with styrene, in the amount of 0.25 through to 2.0 wt.‐%. The effect of the modifier presence on the curing behavior of the resulting resins is discussed.

Gelation times for unsaturated polyester resins modified with modifiers A , B , and C are shown with the curing system consisting of peroxide initiator and (?): 0.10 cm³, (?): 0.15 cm³, (?): 0.25 cm³, and (?): 0.50 cm³ of cobalt(II ) octenate solution per 25 g of resin.     

Glucamine-based gemini surfactants II: Gemini surfactants from long-chain <Emphasis Type="Italic">N</Emphasis>-alkyl glucamines and epoxy resins

Gemini surfactants were synthesized by reaction of long-chain N-alkyl glucamines with epoxy resins. Analogous to the synthesis of gemini surfactns from long-chain N-alkyl glucamines and α, ω-diepoxides (1), the reaction in methanol at 70°C could be used to convert the starting materials selectively and almost quantitatively. N-Octyl glucamine, N-decyl glucamine, and N-dodecyl glucamine were combined with several epoxy resins, mainly technical glycidyl ethers of diols. Syntheses involving equimolar amounts of amine resulted in quantitative conversion of the epoxy resins, and epoxide and products could be isolated quantitatively by removing the solvent. Gemini surfactants having hydrophobic or hydrophilic spacers were preparared according to their structures and the hydrophilic properties of the epoxy resin. Surface tensions were measured, and foaming propertiers were examined to characterize surface-active properties of these surfactants. The more hydrophilic products were of particularly high surface activity. Tensiometric studies showed a reduction of surface tension to 30–34 mN/m and critical micelle concentrations in the range of 2–35 mg/L. Comparison of gemini surfactants from long-chain N-alkyl glucamines and diepoxides of α,ω-diolefins (chain lengths: C₈, C₉, C₁₀, and C₁₄) with those based on epoxy resins showed similar or lower surface activities using hydrophobic epoxy resins and much better surface-active properties using hydrophilic epoxy resins (e.g., based on glycerol). This, together with the easier availability, makes the epoxy resin-based products interesting surfactants. Products having very good surface-active properties are available, especially using glycidyl ether of aliphatic diols or glycerol.     

Microencapsulation of triglycidyl isocyanurate by solvent evaporation method for UV and thermal dual‐cured coatings

Triglycidyl isocyanurate (TGIC), a thermal curing agent, was encapsulated with poly(methyl methacrylate) with small particle size and narrow distribution for the application in acrylic resins to prepare one‐package UV and thermal dual‐cured coatings. Investigation of the wettability and thermal properties suggests that the microcapsules have better compatibility with acrylic resins and thermal stability as compared to pure TGIC. Results of the release performance experiments indicate good storage stability at 25°C and a quick release of vast TGIC at 120°C for the microcapsules. The UV‐thermal dual‐cured coatings prepared with the microcapsules exhibit a fast, even and complete hardening at 130°C together with an excellent adhesion to the mild steel panels. The results presented here show an application potential of the microcapsules in UV and thermal dual‐cured paints. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41008.     

Curing kinetics and mechanical properties of fast curing epoxy resins with isophorone diamine and N-(3-aminopropyl)-imidazole

Fast curing epoxy resins were prepared by the reactions of diglycidyl ether of bisphenol A with isophorone diamine (IPD) and N-(3-aminopropyl)-imidazole (API), and their curing kinetics and mechanical properties influenced by IPD content were also investigated. The analysis of curing kinetics was based on the nonisothermal differential scanning calorimetry (DSC) data with the typical Kissinger, Ozawa, and Flynn–Wall–Ozawa models, respectively. The glass-transition temperature was also measured by the same technique. Additionally, the mechanical properties including flexural, impact, and tensile performances were tested, and the curing time was estimated by isothermal DSC. The degree of cure (α) dependency of activation energy (E_a ) revealed the complexity of curing reaction. Detailed analysis of the curing kinetics at the molecular level indicated that the dependence of E_a on the α was a combined effect of addition reaction, autocatalytic reaction, viscosity, and steric hindrance. From the nonisothermal curves, the curing reaction mechanism could be proposed according to the increasingly obvious low temperature peaks generated by the addition reaction of epoxy group with the primary amines in API and IPD molecules. Using the preferred resin formulation, the resin system could be cured within 10 min at 120 °C with a relatively good mechanical performance. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47950.     

Blended hybrids based on silsesquioxane–OH and epoxy resins

Blended hybrids based on silsesquioxane cyclohexyl trisilanol [STOH; i.e., (c‐C₆H₁₁)₇Si₇O₉(OH)₃] and epoxy resin 4,5‐epoxyhexyl‐1,2‐dimethyl acid diglycidyl ester (TDE‐85) were prepared with good compatibility of STOH up to 5 wt % with TDE‐85. The blended hybrid resins, with various STOH additions, were cured by 4,4′‐diaminodiphenylsulfone, and the curing reactions were investigated with differential scanning calorimetry. The incorporation of STOH increased the curing reaction of TDE‐85 for three active hydrogens existing in the STOH molecule. The storage moduli and glass‐transition temperatures of the cured hybrid resins were studied with dynamic mechanical analysis. The cured hybrids had higher storage moduli than the pure epoxy resins at lower temperatures and increased slightly even when the temperature was above the glass‐transition temperature. Two peaks appearing in tan δ curves indicated the block copolymer structure and two different glass‐transition temperatures of the cured hybrid resins. The thermal stability and flame retardancy of the cured hybrid resins were investigated with thermogravimetric analysis and limited oxygen index values, respectively. The results showed that introducing silsesquioxane–OH units into epoxy resins could improve the thermal stability and flame retardancy of the resins. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Investigation of the curing mechanism and properties of bismaleimide-triazine resins containing phenolphthalein and cyano group

A series of bismaleimide-triazine (BT) resins with and without O, O′-diallyl bisphenol A (DABPA) were produced by mixing 2, 2-bis (4-cyanatophenyl) propane (BADCy) and MCBMI (2,6-bis(4-(1-(4-(4-(2,5-dioxo-2,5-dihydro-1H-pyrrol-1-yl)phenoxy)-3-methylphenyl)-3-oxo-1,3-dihydroisobenzofuran-1-yl)-2-methylphenoxy)benzonitrile). The resins show just one glass-transition temperature (T _g) and enhanced flexural properties as well as superior fracture toughness compared with commercial BDM/BADCy system, in which BDM is (N,N′-bismaleimido-4,4′-diphenylmethane). Introduction of DABPA can decrease the curing temperature of bismaleimide-triazine (BT) resins but increase its impact strength. When the mole of DABPA reach up to 1.2, the impact strength was increased by 1.34 times in comparison with BDM/ BADCy system. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 136, 47420.